去除污泥中重金属铬的生物淋滤反应器设计与应用

用微生物方法去除污泥中重金属(生物淋滤法)是近年来发展的新技术,探索工程化的条件有重要的应用价值。设计了一套容积为1 m3的生物淋滤反应器,由生物淋滤池、搅拌器、曝气器和空气压缩机等构成。其中,搅拌叶轮由平叶桨和斜叶桨组合而成。利用制革污泥进行了半连续的生物淋滤试验,结果表明,在反应器中污泥与菌体和营养物质能充分混匀,经过2~5 d的处理,污泥pH持续下降到2.0以下,污泥中铬的溶出率达90%~99.5%。     

生物淋滤-Fenton对印染污泥脱水性能的影响

采用嗜酸性硫杆菌生物淋滤联合Fenton氧化法对印染污泥脱水性能进行了研究。结果表明,生物淋滤过程中pH下降速率随着硫粉添加量增加而变快,经生物淋滤处理后污泥的脱水性能在一定程度上得到了改善。对生物淋滤后的污泥进行了Fenton氧化处理,获得的最佳反应条件为反应时间2h,H2O2和Fe2＋添加量分别为6g／L和0．5g／L。在该条件下,污泥上清液中总有机碳（TOC）由20．8mg／L增加到356．6mg／L;污泥比阻（SRF）和滤饼含水率分别由5．98×10^11s2／g和88．75％减少至1．26×10^11 S2／g和82．85％。生物淋滤-Fenton氧化法在污泥破解程度和脱水性能改善方面均优于单独Fenton氧化法。     

生物淋滤法处理制革污泥的运行方式研究

生物淋滤技术浸提去除污泥中的重金属，是使污泥洁净化的有效方法。在自行设计的一套总容积为50L的搅拌釜式反应器中进行制革污泥的生物淋滤试验。在连续曝气时，研究了连续搅拌方式和搅拌30min后，停机30、45、60min再搅拌的间歇运行方式的效果。结果表明，连续搅拌运行以及搅拌30min后停机30、45、60min的间歇搅拌运行，分别经过48、60、84、156h的生物淋滤，污泥的pH值下降到2．0以下，氧化还原电位（ORP）上升到530～545mV，铬的溶出率达到99％以上；当固定供气量为9L／min时，污泥中的溶解氧保持在1．2～2．7mg／L；在各种运行方式中，搅拌30min再停机30min的间歇运行方式，其淋滤效果与连续搅拌方式相近，而综合能耗最低，因此，搅拌30min再停机30min的间歇搅拌运行方式可作为工程应用的参考。     

生物淋滤-Fenton对印染污泥脱水性能的影响

采用嗜酸性硫杆菌生物淋滤联合Fenton氧化法对印染污泥脱水性能进行了研究。结果表明,生物淋滤过程中pH下降速率随着硫粉添加量增加而变快,经生物淋滤处理后污泥的脱水性能在一定程度上得到了改善。对生物淋滤后的污泥进行了Fenton氧化处理,获得的最佳反应条件为反应时间2 h,H2O2和Fe2+添加量分别为6 g/L和0.5 g/L。在该条件下,污泥上清液中总有机碳(TOC)由20.8 mg/L增加到356.6 mg/L;污泥比阻(SRF)和滤饼含水率分别由5.98×1011s2/g和88.75%减少至1.26×1011s2/g和82.85%。生物淋滤-Fenton氧化法在污泥破解程度和脱水性能改善方面均优于单独Fenton氧化法。     

Fenton预处理对城市污泥重金属形态及生物淋滤溶出影响

针对生物淋滤处理城市污泥重金属Cr、As和Pd的溶出效率较低的问题,采用芬顿(Fenton)氧化法对城市污泥进行预处理,考察Fenton氧化对污泥中重金属Cr、As和Pd赋存形态转化及后继生物淋滤过程溶出率的影响。实验结果表明,经pH=4.00、Fe~(2+)=1.00 g·L~(-1)、H_2O_2=9 g·L~(-1)的条件下Fenton预处理后,重金属Cr、As和Pb的存在形态均由稳定性较强的可氧化态和残渣态向不稳定的弱酸提取态和可还原态转化,其不稳定态比重分别由15%、30%、9%提高到了24%、41%、11%;生物淋滤实验结果显示,由于重金属形态变化,重金属Cr、As和Pb溶出率分别由52.71%、11.15%、33.19%提升至60.76%、24.32%、45.96%。Fenton预处理联合生物淋滤法提高了对重金属Cr、As和Pb的去除效果,有助于实现污泥的无害化处理处置。     

生物淋滤改善城市污泥的脱水性能

污水处理过程中产生大量剩余污泥,使得污泥脱水逐渐成为污泥处理的关键环节。本研究采用生物淋滤方法处理城市污泥,改善污泥脱水性能。通过污泥比阻、滤饼含水率和离心脱水率的变化评价生物淋滤改善剩余污泥脱水性能的效能。综合考虑污泥脱水性能改善效果和运行成本,生物淋滤优化条件为:硫粉投加量3 g/L;Fe2+投加量4 g/L;接种物投加量(接种物与供试污泥的体积比,mL/mL)0.4。在优化条件下,污泥体系被酸化至pH为2.0左右需要36～48 h,淋滤污泥的比阻由1.26×1014 m/kg降至8.14×1012 m/kg,降低了93.54%,滤饼含水率从98.39%降至73.68%,同时污泥离心脱水率从72%提高到83%。回调淋滤污泥pH至6.0,污泥比阻继续降至8.27×1011 m/kg,污泥比阻降低99.34%,污泥从难脱水状态转化为易脱水状态。通过污泥体系中铁离子和污泥絮体特征的变化,分析生物淋滤改善污泥脱水性能的机理。作为底物投加的Fe2+在微生物氧化作用下快速转化为Fe3+。生物氧化产生的Fe3+的絮凝作用可能是生物淋滤改善污泥脱水性能的主要机理。     

好氧颗粒污泥对膜生物反应器污泥性能的影响

采用膜生物反应器进行含酚废水的处理,探讨投加好氧颗粒污泥对反应器中污泥性能的影响。结果表明,在膜生物反应器中投加好氧颗粒污泥能有效改善污泥性能,提高处理效果。从采用絮状污泥到逐渐增加好氧颗粒污泥投加量为100%的过程中,反应器中污泥浓度明显提高,MLSS由5 582 mg/L增加到8 168 mg/L;沉降性能得到改善,SVI由135.85 mL/g下降到29.36 mL/g;疏水性增强,Zeta电位由-20.302 mV升高到-4.325 mV;对含酚废水中COD、NH3-N的降解能力明显提高,COD、NH3-N、NO3-N去除率分别由87.3%、83.2%、55.3%增加到99.2%、94.9%、66.3%。改善了膜污染现象,膜通量衰减率由63.3%降低到42.8%。用二元多项式三维回归分析,得到污染物去除率关于好氧颗粒污泥投加量和反应器运行时间的二元方程,对指导好氧颗粒污泥膜生物反应器的连续运行具有重要意义。     

附着性胞外多聚物对HMBR膜污染控制性能的影响

采用复合式膜生物反应器（HMBR）处理城市生活污水,对附着性胞外多聚物影响HMBR膜污染控制性能的作用机理进行了研究。实验结果表明,HMBR中附着性胞外多聚物、松散附着性胞外多聚物和紧密附着性胞外多聚物的浓度比常规膜生物反应器分别降低了10．0％、43．6％和2．1％。附着性胞外多聚物与膜表面滤饼层污泥比阻的关系较为密切,随着其浓度逐渐降低,滤饼层污泥比阻相应减小。与紧密附着性胞外多聚物相比,松散附着性胞外多聚物对滤饼层污泥比阻的影响程度更深。因此,随着反应器中附着性胞外多聚物特别是松散附着性胞外多聚物浓度的降低,HMBR的膜污染控制性能增强,反应器中膜表面的滤饼层阻力比常规膜生物反应器降低了56．9％。     

生物淋滤技术对城市污泥中高浓度重金属的去除

实验以单质硫粉作为能源基质,考查了生物淋滤技术针对城市污泥中高浓度重金属的去除效果,探讨了生物淋滤处置前后污泥中重金属的形态变化规律。结果表明,生物淋滤技术能够有效去除污泥中的高浓度重金属。在硫粉投加量为4 g·L~(-1)、HRT为5 d、污泥回流比为50%、污泥浓度为4%、温度为30℃的条件下,生物淋滤系统pH值可降低至1.5左右,污泥中残留重金属Zn、Cu、Cr、Ni分别可降低至400、400、900和200 mg·kg~(-1)左右,达到了《城镇污水处理厂污泥处置林地用泥质》(CJ/T 362~(-2)011)标准重金属限值。生物淋滤处置后,污泥中残留重金属Zn、Cu、Cr、Ni均主要以稳定形态存在,环境风险较低,为进行土地利用奠定了物质基础。     

复合生物反应器工艺对化纤废水的处理研究

在普通活性污泥系统的曝气池中投加一定量的填料构成复合生物反应器,可以增加曝气池中的生物体量至6g／L左右,在HRT为8h,泥龄为5d时,CODCR、氨氮的去除率分别提高了20％和9．6％,容积负荷对复合生物反应器的脱氮能力影响较小。该工艺对污泥膨胀有较好的控制。     

Bioleaching of heavy metals from livestock sludge by indigenous sulfur-oxidizing bacteria: effects of sludge solids concentration

A technologically and economically feasible process called bioleaching was used for the removal of heavy metals from livestock sludge with indigenous sulfur-oxidizing bacteria in this study. The effects of sludge solids concentration on the bioleaching process were examined in a batch bioreactor. Due to the buffering capacity of sludge solids, the rates of pH reduction, ORP rise and metal solubilization were reduced with the increase of the solids concentration. No apparent influence of solids concentration on sulfate produced by sulfur-oxidizing bacteria was observed when the solids concentration was less than 4% (w/v). A Michaelis-Menten type of equation was able to well describe the relationship between solids concentration and rate of metal solubilization. Besides, high efficiencies of metal solubilization were achieved after 16 d of bioleaching. Therefore, the bioleaching process used in this study could be applied to remove heavy metals effectively from the livestock sludge.     

Enhanced Cr bioleaching efficiency from tannery sludge with coinoculation of Acidithiobacillus thiooxidans TS6 and Brettanomyces B65 in an air-lift reactor

Bioleaching process has been demonstrated to be an effective technology in removing Cr from tannery sludge, but a large quantity of dissolved organic matter (DOM) present in tannery sludge often exhibits a marked toxicity to chemolithoautotrophic bioleaching bacteria such as Acidithiobacillus thiooxidans. The purpose of the present study was therefore to enhance Cr bioleaching efficiencies through introducing sludge DOM-degrading heterotrophic microorganism into the sulfur-based sludge bioleaching system. An acid-tolerant DOM-degrading yeast strain Brettanomyces B65 was successfully isolated from a local Haining tannery sludge and it could metabolize sludge DOM as a source of energy and carbon for growth. A combined bioleaching experiment (coupling Brettanomyces B65 and A. thiooxidans TS6) performed in an air-lift reactor indicated that the rates of sludge pH reduction and ORP increase were greatly improved, resulting in enhanced Cr solubilization. Compared with the 5 days required for maximum solubilization of Cr for the control (single bioleaching process without inoculation of Brettanomyces B65), the bioleaching period was significantly shorten to 3 days for the combined bioleaching system. Moreover, little nitrogen and phosphorous were lost and the content of Cr was below the permitted levels for land application after 3 days of bioleaching treatment.     

元素硫颗粒粒径对污泥重金属生物沥滤的影响

以城市污水处理厂剩余污泥作为处理介质,土著嗜酸氧化硫硫杆菌(Acidithiobacillus thiooxidans,A.thiooxi-dans)为主要沥滤微生物,采用序批式生物沥滤装置,就投加150~725μm的不同粒径元素硫对沥滤的酸化效果、硫酸根产率和重金属去除效果的影响进行了研究。结果表明,在元素硫投配量为3 g/L,曝气强度为1.0 L/(min.L)的条件下,元素硫粒径在165~215μm范围减小时能显著改善污泥酸化速度、提高酸化程度和硫酸根产率。底物元素硫的最佳粒径为165μm,此时沥滤体系pH下降速率为0.85个pH单位/d,硫酸根的产率为454.9 mg/(L.d),沥滤6 d后污泥中高浓度重金属Cu、Zn、Cd的去除率达到70.3%、81.2%、87.8%.     

Bioleaching of heavy metals from anaerobically digested sewage sludge using FeS2 as an energy source

The effect of using FeS2 as an energy source, on the bioleaching of heavy metals (Zn, Cr, Cu, Pb and Ni) and nutrients (nitrogen and phosphorus) from anaerobically digested sludge using isolated indigenous iron-oxidizing bacteria was investigated in this paper. Addition of FeS2 in the range of 0.5-4.0 g l(-1) accelerated the acidification of sludge and raised the oxidation-reduction potential of sludge medium with an inoculation of 15% (v/v) of active bacteria, thus resulting in an overall increase in metal dissolution efficiency. After 16 days of bioleaching at 28 degrees C and an initial pH of 3.0, up to 99% of Zn, 65% of Cr, 74% of Cu, 58% of Pb and 84% of Ni can be removed from the sludge. In contrast, only 94% of Zn, 12% of Cr, 21% of Cu, 32% of Pb and 38% of Ni were leached out in the control without inoculation of iron-oxidizing bacteria and the addition of FeS2. Less than 15% of nitrogen and 6% of phosphorous were lost after 16 days of bioleaching when using FeS2 as the energy source. Comparing to 39% and 45% loss respectively for these two nutrients when using FeSO4.7H2O as the energy source, FeS2 appears to be a more suitable energy source for preserving nutrients in sludge while removing heavy metals from sludge.     

提高生物法分离制革污泥中铬分离效率的研究

在已确定污泥驯化最佳条件的基础上,通过改变滤材、液固分离条件,添加营养物质继续降低pH等方法,进行提高生物沥滤法分离制革污泥中铬的分离效率的研究。同时考察化学沥滤法（1∶1硫酸）在相同条件下的分离效率。试验结果表明：用相应pH值酸液（1∶1硫酸配制）淋洗,淋洗+闷洗和抽真空＋酸液淋洗等过滤方式可提高铬的分离效率。生物沥滤中当pH值下降至1.8时,分离效率即可达到94.65%,与直接用蒸馏水淋洗相比要高得多。化学沥滤中当pH值下降到1时,分离效果可达96.7%,沥滤污泥中剩余铬含量可达到制革污泥农用标准。     

废旧镍镉电池的生物沥滤处理——沥滤停留时间的影响研究

用污泥加硫酸化液沥滤镍镉电池中的重金属是一种全新的工艺,该工艺主要由生物酸化反应器和金属沥滤反应器两个反应器组成.生物酸化反应器中产生的酸液就是沥滤电池中重金属的反应液.研究表明,酸化液在沥滤反应池的停留时间对沥滤的效果有显著影响.在1、4、7、12 d 4个停留时间中,4 d的效果是最好的,对金属Cd和Ni都用40 d左右基本实现了全部滤除;1d略微慢一些,Cd用了40 d,Ni用了45 d;7 d和12 d的沥滤时间都长于50 d.4 d产生的金属废液量是1 d的1/4,考虑到后续处理金属沥滤废液的工作量,选择4d的停留时间要优于1d.     

微生物沥浸法去除底泥中的重金属

以硫酸亚铁盐为底物,培养以氧化亚铁硫杆菌为主要菌种的土著沥滤微生物,采用批式方法对湘江长沙段底泥进行微生物沥浸实验。实验结果表明,底物投加量与底泥固体浓度比(Sd/Sc)为1.5时已能满足底泥的微生物沥浸要求,进一步研究发现底泥固体浓度为13%、底物投加量为19.5 g/L、沥浸时间为6 d时,底泥中超标重金属Cd、Zn和Cu的去除率可分别达到83.1%、75.3%和61.2%;沥浸后底泥中大部分重金属以残渣态存在,且含量低于农用污泥中污染物控制标准,其中硫化物有机结合态Cu浸出较Zn、Cd需更低的pH,且Cu以间接机理浸出为主;以Fe2+为底物的沥浸体系中,黄铁矾的重吸附或共沉淀是沥浸实验后期重金属浸出率下降的原因之一。     

The efficiency of two standardized procedures for extracting mutagenic chemicals from soils

A major technical limitation to monitoring the fate of mutagenic compounds in soil is the lack of an established extraction procedure. This study was conducted to evaluate the efficiency of the blender extraction procedure for extracting benzo(a)pyrene (BAP) or 2-nitrofluorene (2NF) from a Weswood silt loam or a Bastrop clay loam soil. Extracted residues were evaluated using the Salmonella/microsome mutagenicity assay and high performance liquid chromatography (HPLC) to quantify recovery of the two chemicals from soil. In addition, a limited study using only the mutagenicity assay was conducted to compare the efficiency of the Blender and Soxhlet extraction procedures for recovering organic mutagens from both soils amended with a wood preserving bottom sediment waste.Extracted residues were dissolved in dimethylsulfoxide to concentrations that could be detected in the bioassay. Over all treatment levels and for both soils, the extraction efficiency of the blender procedure for BAP was greater than 80% for 12 of 16 treatments as measured using both bioassay and HPLC analysis; while, for 2NF the extraction efficiency was greater than 90% for all 15 treatments as measured by HPLC, and greater than 80% for twelve of 15 treatments as measured by bioassay. These results indicate that blender extraction provided efficient recovery of the pure compounds tested. When the efficiency of the blender and Soxhlet procedure for extracting the wood-preserving bottom sediment and waste amended soil were compared, significantly greater levels of mutagenic activity were detected in the fractions extracted using the blender extraction than were detected using the Soxhlet extraction.     

生物法和化学法回收制革污泥中铬的对比研究

研究了嗜酸性硫杆菌(Thiobacillus)生物沥滤法和1:1硫酸化学沥滤法分离回收制革污泥中的铬.比较了嗜酸性硫杆菌生物沥滤法和化学沥滤法回收制革污泥铬过程中pH、氧化还原电位(ORP)、沉降比(SV)以及铬的沥滤率的变化.试验结果表明,pH是影响制革污泥中铬的沥滤率的关键因素.生物沥滤法在使污泥pH大幅度降低的同时,能很好地改善污泥的沉降性能,对铬的沥滤效果好于化学沥滤法.