PCE solubilization and mobilization by commercial humic acid

In this paper, comparison is made of terms describing solubilization of hydrophobic organic compounds (HOC) by dissolved humic substances (DHS) and commercial non-ionic surfactants. This paper examines the ability of a commercial humic acid (Aldrich humic acid) to solubilize and mobilize tetrachlorothene (PCE) residual in porous media. The constant for solubilization of PCE by Aldrich humic acid is shown to be a factor of two to thirty times less than that published for dodecyl alcohol ethoxylate surfactants, showing that Aldrich humic acid is less capable than some non-ionic surfactants at solubilizing residual PCE. The depression of PCE–water interfacial tension in the presence of DHS is shown to be significantly less than published values for a non-ionic surfactant, and surfactant mixtures, indicating that the DHS used in this study is less prone to cause mobilization of non-aqueous phase liquids relative to surfactants. Several possible advantages of DHS use in the remediation of subsurface media contaminated with HOC are described, including the ability of DHS to solubilize HOC irrespective of the DHS concentration, and potential lesser tendency of DHS to depress the interfacial tension between non-aqueous phases and water relative to surfactants (an advantage when mobilization is undesired).     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.     

Leaching characteristics of polybrominated diphenyl ethers (PBDEs) from flame-retardant plastics

To investigate the effect of leachant on the leachability of polybrominated diphenyl ethers (PBDEs), we determined the leaching concentrations of PBDEs from flame-retardant plastic samples (TV housings and raw materials before molding processing) that are regarded as a source of PBDEs in landfill sites. The leachants used were distilled water, 20% methanol solution, and dissolved humic solution (DHS) of 1000 mg/l based on organic carbon. The leaching test conditions were a liquid-to-solid ratio of 100:1, and a contact period of five days, with twice-daily agitation in a temperature-controlled room of 30 degrees C without pH or ionic strength control. The leaching concentrations of PBDEs increased with increased content, and were found to be remarkably enhanced when methanol and DHS were used instead of distilled water. The enhancement of leachability in the presence of the latter was attributed to the cosolvency effect, and complex formations between the PBDEs and dissolved humic matter (DHM). PBDE concentrations in the leachate obtained from the leaching test and an actual landfill site revealed a significant presence of congeners below heptabromodiphenyl ethers (H7BDEs), detected in the leachate of the actual landfill, while significant amounts of nonabromodiphenyl ethers (N9BDEs) and decabromodiphenyl ether (D10BDE) were detected in the leachate of the leaching test.     

The effects of dissolved organic matter and pH on sampling rates for polar organic chemical integrative samplers (POCIS)

The effect of solution pH and levels of dissolved organic matter (DOM) on the sampling rates for model pharmaceuticals and personal care products (PPCPs) and endocrine disrupting substance (EDS) by polar organic chemical integrative samplers (POCIS) was investigated in laboratory experiments. A commercially available POCIS configuration containing neutral Oasis HLB (hydrophilic-lipophilic balance) resin (i.e. pharmaceutical POCIS) and two POCIS configurations prepared in-house containing MAX and MCX anion and cation exchange resins, respectively were tested for uptake of 21 model PPCPs and EDS, including acidic, phenolic, basic and neutral compounds. Laboratory experiments were conducted with dechlorinated tap water over a pH range of 3, 7 and 9. The effects of DOM were studied using natural water from an oligotrophic lake in Ontario, Canada (i.e. Plastic Lake) spiked with different amounts of DOM (the concentration of dissolved organic carbon ranged from 3 to 5 mg L⁻¹ in uptake experiments). In experiments with the commercial (HLB) POCIS, the MCX-POCIS and the MAX-POCIS, the sampling rates generally increased with pH for basic compounds and declined with pH for acidic compounds. However, the sampling rates were relatively constant across the pH range for phenols with high pKa values (i.e. bisphenol A, estrone, estradiol, triclosan) and for the neutral pharmaceutical, carbamazepine. Thus, uptake was greatest when the amount of the neutral species in solution was maximized relative to the ionized species. Although the solution pH affected the uptake of some model ionic compounds, the effect was by less than a factor of 3. There was no significant effect of DOM on sampling rates from Plastic Lake. However, uptake rates in different aqueous matrixes declined in the order of deionized water > Plastic Lake water > dechlorinated tap water, so other parameters must affect uptake into POCIS, although this influence will be minor. MAX-POCIS and MCX-POCIS showed little advantage over the commercial POCIS configuration for monitoring in natural waters.     

Photocatalytic oxidation of toxic organohalides with TiO2/UV: the effects of humic substances and organic mixtures

TiO2/UV photocatalytic oxidation of DDT (1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane), 1,2,3-trichlorobenzene and 4-chlorophenol were examined in aqueous solution in the presence of humic substances and organic mixtures to study if the degradation rates were affected. Both commercial and natural humic substances were observed to retard the photodegradation rates, with a greater effect from the natural humic substances. Acetonitrile and isopropanol also caused significant retardation of 4-chlorophenol photodegradation. The overall retardation can be attributed to the combination of light attenuation, inhibition and competition effects. Moreover, the TiO2/UV system favors the decomposition of compounds that have stronger adsorption onto the TiO2 surface. To engineer effective treatment facilities that use the TiO2/UV system for the treatment of toxic substances in wastewater, the methodology must allow for concerns about adventitious species which are present.     

Enhanced oxidation of methoxy phenols at micromolar concentration photosensitized by dissolved natural organic material

The rate coefficients for the photosensitized oxidation of various phenols in aqueous solutions containing dissolved natural organic material increased in some cases with decreasing phenol concentration. For 3,4-dimethoxyphenol and 4-methoxyphenol at initial concentration going from 10 to 1.0 μM, the rate coefficients increased by a factor of 5 in a humic acid solution and by a factor of 2 in a fulvic acid solution and a lake water. For 2,4,6-trimethylphenol, 4-methylphenol and phenol at initial concentration going from 15 to 2.5 μM, they increased by a factor < 2 in the humic acid solution and were constant in the fulvic acid solution and the lake water. We suggest that the methoxy phenols, which are known to easily reduce oxidants, readily react with a class of photo-oxidants whose lifetime is expected to be > 100 μs. Thereby the long-lived photo-oxidants seem to be scavenged by the phenols themselves.     

Partitioning behaviour of perfluorinated alkyl contaminants between water, sediment and fish in the Orge River (nearby Paris, France)

This paper reports on the partitioning behaviour of 15 perfluorinated compounds (PFCs), including C₄-C₁₀ sulfonates and C₅-C₁₄ carboxylic acids, between water, sediment and fish (European chub, Leuciscus cephalus) in the Orge River (nearby Paris). Total PFC levels were 73.0 ± 3.0 ng L⁻¹ in water and 8.4 ± 0.5 ng g⁻¹ in sediment. They were in the range 43.1-4997.2 ng g⁻¹ in fish, in which PFC tissue distribution followed the order plasma > liver > gills > gonads > muscle. Sediment-water distribution coefficients (log K_d) and bioaccumulation factors (log BAF) were in the range 0.8-4.3 and 0.9-6.7, respectively. Both distribution coefficients positively correlated with perfluoroalkyl chain length. Field-based biota-sediment accumulation factors (BSAFs) are also reported, for the first time for PFCs other than perfluorooctane sulfonate. log BSAF ranged between −1.3 and 1.5 and was negatively correlated with the perfluoroalkyl chain length in the case of carboxylic acids.     

Determination of total organic halogen (TOX) in humic acids after microwave-induced combustion

Chemically chlorinated organic matter as well as natural background humic acids contain significant amounts of organically bound halogens that must be determined for assessment of environmental pollution. In this work the use of ion chromatography (IC) and inductively coupled plasma mass spectrometry (ICP-MS) is proposed for the determination of total organic Cl, Br and I concentration in humic acids extracted from various forest soil horizons after a single digestion by microwave-induced combustion (MIC). Samples were pressed as pellets and combusted using 20 bar of oxygen and ammonium nitrate solution as igniter. Analytes were absorbed in diluted alkaline solution (50 mM (NH₄)₂CO₃) and a reflux step was applied after combustion to improve analyte recoveries (5 min, microwave power of 1400 W). The accuracy was evaluated using certified reference materials (CRM) and spiked samples. Using MIC the agreement with CRM values and spike recoveries was higher than 97% for all analytes. As an advantage over conventional procedures, using MIC it was possible to digest up to eight samples in only 25 min, obtaining a single solution suitable for all halogens determination in humic acids samples by different techniques (IC and ICP-MS). The limit of detection (3σ) for Cl, Br and I obtained by IC was 1.2, 2.5 and 4.3 μg g⁻¹ and by ICP-MS it was 1.4, 0.03 and 0.002 μg g⁻¹, respectively.     

Significance of analytical parameters for the understanding of natural organic matter in relation to photocatalytic oxidation

In this review, special interest was devoted to provide information on the surrogate parameters expressing both quality and quantity of organic matter for the understanding of the photocatalytic oxidation of humic substances. Detailed investigation was directed to the application of photocatalysis with reference to source, origin and modeling of organic matter. Evaluation of the literature findings emphasizes that organic matter taken from natural waters are site specific and should be characterized in detail to be comparable to other studies. Taking into account the photocatalytic degradation studies of natural organic matter, humic substances, humic acids and fulvic acids in slurry systems, a procedure could be deduced that depends on the selection of a standard model sample with a representative concentration, selection of a standard photocatalyst and dose (e.g., TiO₂ Degussa P-25, 0.25 mg mL⁻¹), application of standardized reaction conditions such as light intensity, pH, and temperature. Furthermore, standardized filtration step avoiding organic leaching and selection of the most suitable analytical parameter are the crucial points to be considered. The use of such a protocol could form a basis for the determination of “relative degradation efficiency” of any sample containing natural organic matter, humic substances, humic acids and fulvic acids regardless of dependency on source and origin.     

Evaluating the impacts of some environmentally relevant factors on the availability of bisphenol A with negligible-depletion SPME

The effect of some environmentally relevant factors including salinity, pH, and humic acids on the availability of bisphenol A (BPA) was evaluated by using the negligible-depletion solid-phase microextraction (nd-SPME) biomimetic method. With the variation of salinity (0–500 mM NaCl) and pH (5.0–8.5) of aqueous solutions, the partition coefficients of BPA between the nd-SPME fiber and the aqueous solution varied in the range of log D = 3.55–3.86, which indicates that the salinity and pH can influence the availability of BPA. By using Acros humic acid as model dissolved organic matter (DOM), it was also demonstrated that the environmental factors such as salinity and pH could affect the partitioning of BPA between DOM and aqueous solutions. The determined partition coefficients of BPA between dissolved organic carbon (DOC) and aqueous solutions were in the range of log D_DOC = 4.03–5.60 for Acros humic acid solutions with 1–50 mg l⁻¹ DOC. The influence of salinity and pH on log D_DOC was more significant at low concentration (0–5 mg l⁻¹) of DOC.     

Determining the role of humic substances in the fate of pesticides in the environment

Abstract

The data presented in this paper emphasize that the behavior and fate of pesticides in the environment is influenced by humic substances. Various methods most frequently used for the characterization of humic substances are discussed. Both humic acid and fulvic acid can solubilize in water certain organic compounds and are important carriers of some pesticides in soil. Humic substances have the potential for promoting the nonbiological degradation of many pesticides. Several methods of bleaching humus color from drinking water, including chlorination, ozonation, and UV‐radiation, are described. Finally, the photochemical stability to UV‐radiation of certain pesticides in aqueous fulvic acid solution is discussed.     

Ozonation of azo dye Acid Red 14 in a microporous tube-in-tube microchannel reactor: decolorization and mechanism

Despite the great success of time-weighted average passive sampling of hydrophobic contaminants, such as PCBs and PAHs, the sampling of polar organic compounds still presents a challenge because the equilibrium between water and most sampling phases is attained in a relatively short time. In this study, we proposed a new time-integrative sampler using in situ solvent extraction (TISIS) for polar organic chemicals. The sampler was composed of a 15 cm poly(dimethylsiloxane) (PDMS) tubing, with an internal diameter of 0.5 mm and wall thickness of 0.5 mm, through which an extraction solvent (acetonitrile) was passed. Four polar organic contaminants, caffeine, atrazine, diuron and 17α-ethynylestradiol, were chosen for the evaluation of the performance of the sampler. Without the use of in situ solvent extraction, the PDMS tubing when exposed to a constant aqueous concentration of the four model compounds was able to linearly accumulate those compounds for less than 12 h and equilibrium between the PDMS tubing and water was attained in 2 d under our laboratory conditions. However, TISIS when exposed to a constant aqueous concentration was able to linearly accumulate all the model compounds without any exposure time limitation. The measured sampling rates at three different extraction flow rates (0.2, 0.5, 1.5 mL min⁻¹) were similar, regardless of the chemicals, indicating that the overall mass transfer from aqueous solution to the extraction solvent was most likely dominated by partitioning to the PDMS tubing and the internal diffusion within PDMS. In addition, a pulsed exposure experiment confirmed that TISIS operated in a time-integrative mode when the environmental concentration was highly fluctuated.     

Influence of Suwannee River humic acid on particle properties and toxicity of silver nanoparticles

Adsorption of natural organic matter (NOM) on nanoparticles can have dramatic impacts on particle dispersion resulting in altered fate and transport as well as bioavailability and toxicity. In this study, the adsorption of Suwannee River humic acid (SRHA) on silver nanoparticles (nano-Ag) was determined and showed a Langmuir adsorption at pH 7 with an adsorption maximum of 28.6 mg g⁻¹ nano-Ag. It was also revealed that addition of <10 mg L⁻¹ total organic carbon (TOC) increased the total Ag content suspended in the aquatic system, likely due to increased dispersion. Total silver content decreased with concentrations of NOM greater than 10 mg TOC L⁻¹ indicating an increase in nanoparticle agglomeration and settling above this concentration. However, SRHA did not have any significant effect on the equilibrium concentration of ionic Ag dissolved in solution. Exposure of Daphnia to nano-Ag particles (50 μg L⁻¹ and pH 7) produced a linear decrease in toxicity with increasing NOM. These results clearly indicate the importance of water chemistry on the fate and toxicity of nanoparticulates.     

A new approach for estimating emissions of organic solutes and organic solvents under wind speeds

A new approach is developed to predict the volatilization loss of the pure liquid and the volatilization rates of organic solutes with different Henry's law constants (H) under wind speed. The tested compounds include eight volatile organic compounds for pure liquid and the forty-one organic solutes with different H compounds are divided into three groups that span seven H orders. The wind speed is set from 0 to 6.0 ms^?1. A characteristic parameter ε was established to estimate volatilization loss of pure organic compounds. The mass transfer coefficient (K_OL) ratios of the organic solutes, under both wind speed and still conditions, are applied to describe the volatilization characteristics of the selected solutes. The curve profile for K_OL ratios and ε values relative to the selected wind speed can be divided into two stages, the sharp-rise stage and the stable-linearity stage. The critical finding is the ε values for the different organic compounds under a specific wind speed approach a constant. The changes in the curve profile of the K_OL ratios are similar to the ε values of the pure organic compounds. It is also found the relatively lower H compounds exhibit a sensitive wind effect on the K_OL ratios. The K_OL ratios of the relatively higher H compounds indicate a similar linear increase with the increasing wind speed in the two stages. Accordingly, concentrations of the organic compounds at the interface are thought to the primary factor. The obtained results could be a good reference to estimate volatilization loss of the organic solutes or the organic solvents under different wind speed conditions.     

Relative influence of the dissolved humic material on the solid-phase extraction efficiency of pesticides from environmental water

The effect of organic matter on the solid-phase extraction (SPE) efficiency for pesticides belonging to different chemical groups (urea-derivatives, carbamates and triazines) and having different polarities, was simultaneously studied for the first time in pure and simulated water samples. SPE was carried out in precolumns packed with C18 silica or styrene-divinylbenzene copolymer PLRP-S phases on-line coupled to high performance liquid chromatography (HPLC) analysis. Retention factors in water (k'(W)) were estimated for 25 compounds and used for the calculation of the theoretical breakthrough volume (Vb(T)) in pure water. Experimental breakthrough volumes (Vb(E)) were first determined using purified and deionized water as the matrix for selected compounds having Vb(T) < 500 mL; then, the same water with an added humic acid sodium salt (HA) at 0.4-5.6 mg/L of dissolved organic carbon (DOC) content, was used as the matrix for compounds having VbE < 500 mL in pure water. Several polar pesticides showed negative linear or logarithmic Vb(E) curves depending on HA content; their recoveries were also determined in environmental samples having low dissolved organic carbon values, between 0.5-6.4 mg/L. A similar behavior was observed for these compounds in simulated and natural water samples, where DOC concentration and the percolated volume (Vp) mainly determine the solute recoveries values. However, the variation of recoveries as a function of DOC content could be negative or null depending on the two examined conditions (Vp lower or larger than Vb(E) in pure water). Results demonstrated that breakthrough volume must always be considered to correctly interpret the participation of dissolved humic material on the SPE efficiency of organic micropollutants in water.     

Determining the role of human substances in the fate of pesticides in the environment

The data presented in this paper emphasize that the behavior and fate of pesticides in the environment is influenced by humic substances. Various methods most frequently used for the characterization of humic substances are discussed. Both humic acid and fulvic acid can solubilize in water certain organic compounds and are important carriers of some pesticides in soil. Humic substances have the potential for promoting the nonbiological degradation of many pesticides. Several methods of bleaching humus color from drinking water, including chlorination, ozonation, and UV-radiation, are described. Finally, the photochemical stability to UV-radiation of certain pesticides in aqueous fulvic acid solution is discussed.     

Nitrate-induced photodegradation of atenolol in aqueous solution: kinetics, toxicity and degradation pathways

The extensive utilization of β-blockers worldwide led to frequent detection in natural water. In this study the photolysis behavior of atenolol (ATL) and toxicity of its photodegradation products were investigated in the presence of nitrate ions. The results showed that ATL photodegradation followed pseudo-first-order kinetics upon simulated solar irradiation. The photodegradation was found to be dependent on nitrate concentration and increasing the nitrate from 0.5 mM L⁻¹ to 10 mM L⁻¹ led to the enhancement of rate constant from 0.00101 min⁻¹ to 0.00716 min⁻¹. Hydroxyl radical was determined to play a key role in the photolysis process by using isopropanol as molecular probe. Increasing the solution pH from 4.8 to 10.4, the photodegradation rate slightly decreased from 0.00246 min⁻¹ to 0.00195 min⁻¹, probably due to pH-dependent effect of nitrate-induced OH formation. Bicarbonate decreased the photodegradation of ATL in the presence of nitrate ions mainly through pH effect, while humic substance inhibited the photodegradation via both attenuating light and competing radicals. Upon irradiation for 240 min, only 10% reduction of total organic carbon (TOC) can be achieved in spite of 72% transformation rate of ATL, implying a majority of ATL transformed into intermediate products rather than complete mineralization. The main photoproducts of ATL were identified by using solid phase extraction-liquid chromatography-mass spectrometry (SPE-LC-MS) techniques and possible nitrate-induced photodegradation pathways were proposed. The toxicity of the phototransformation products was evaluated using aquatic species Daphnia magna, and the results revealed that photodegradation was an effective mechanism for ATL toxicity reduction in natural waters.     

Relative influence of the dissolved humic material on the solid-phase extraction efficiency of pesticides from environmental water

The effect of organic matter on the solid-phase extraction (SPE) efficiency for pesticides belonging to different chemical groups (urea-derivatives, carbamates and triazines) and having different polarities, was simultaneously studied for the first time in pure and simulated water samples. SPE was carried out in precolumns packed with C18 silica or styrene-divinylbenzene copolymer PLRP-S phases on-line coupled to high performance liquid chromatography (HPLC) analysis. Retention factors in water (k'_W) were estimated for 25 compounds and used for the calculation of the theoretical breakthrough volume (Vb_T) in pure water. Experimental breakthrough volumes (Vb_E) were first determined using purified and deionized water as the matrix for selected compounds having Vb_T < 500 mL; then, the same water with an added humic acid sodium salt (HA) at 0.4–5.6 mg/L of dissolved organic carbon (DOC) content, was used as the matrix for compounds having VbE < 500 mL in pure water. Several polar pesticides showed negative linear or logarithmic Vb_E curves depending on HA content; their recoveries were also determined in environmental samples having low dissolved organic carbon values, between 0.5–6.4 mg/L. A similar behavior was observed for these compounds in simulated and natural water samples, where DOC concentration and the percolated volume (Vp) mainly determine the solute recoveries values. However, the variation of recoveries as a function of DOC content could be negative or null depending on the two examined conditions (Vp lower or larger than Vb_E in pure water). Results demonstrated that breakthrough volume must always be considered to correctly interpret the participation of dissolved humic material on the SPE efficiency of organic micropollutants in water.     

Characterization of dissolved organic matter using high-performance liquid chromatography (HPLC)-size exclusion chromatography (SEC) with a multiple wavelength absorbance detector

High-performance liquid chromatography-size exclusion chromatography (HPLC-SEC) coupled with a multiple wavelength absorbance detector (200-445 nm) was used in this study to investigate the apparent molecular weight (AMW) distributions of dissolved organic matter (DOM). Standard DOM, namely humic acid, fulvic acid and hydrophilic acid, from the Suwannee River were tested to ascertain the performance and sensitivity of the method. In addition to four compounds groups: humic substances (Peak 1, AMW 16 kD), fulvic acids (Peak 2, AMW 11 kD), low AMW acids (Peak 3, AMW 5 kD), and low AMW neutral and amphiphilic molecules, proteins and their amino acid building blocks (Peak 4, AMW 3 kD), an new group that appears to include low AMW, 6-10 kD, humic substances was found based on investigating the spectra at various elution times. The spectroscopic parameter S_>365 (slope at wavelengths >365 nm) was determined to be a good predictor of the AMW of the DOM. The detector wavelength played an important role in evaluating the AMW distribution. For some fractions, such as the humic and low AMW non-aromatic substances, the error in measurement was ±30% as determined by two-dimensional chromatograms detected at an artificially selected wavelength. HPLC-SEC with multiple wavelength absorbance detection was found to be a useful technique for DOM characterization. It characterized the AMW distributions of DOM more accurately and provided additional, potentially important information concerning the properties of DOM with varying AMWs.     

Influence of aggregated particles on biodegradation activities for dimethylarsinic acid (DMA) in Lake Kahokugata

Aquatic arsenic cycles mainly depend on microbial activities that change the arsenic chemical forms and influence human health and organism activities. The microbial aggregates degrading organic matter are significantly related to the turnover between inorganic arsenic and organoarsenic compounds. We investigated the effects of microbial aggregates on organoarsenic mineralization in Lake Kahokugata using lake water samples spiked with dimethylarsinic acid (DMA). The lake water samples converted 1 μmol L⁻¹ of DMA to inorganic arsenic for 28 d only under anaerobic and dark conditions in the presence of microbial activities. During the DMA mineralization process, organic aggregates >5.0 μm with bacterial colonization increased the densities. When the organic aggregates >5.0 μm were eliminated from the lake water samples using filters, the degradation activities were reduced. DMA in the lake water would be mineralized by the microbial aggregates under anaerobic and dark conditions. Moreover, DMA amendment enhanced the degradation activities in the lake water samples, which mineralized 50 μmol L⁻¹ of DMA. The DMA-amended aggregates >5.0 μm completely degraded 1 μmol L⁻¹ of DMA with a shorter incubation time of 7 d. The supplement of KNO₃ and NaHCO₃ to lake water samples also shortened the DMA-degradation period. Presumably, the bacterial aggregates involved in the chemical heterotrophic process would contribute to the DMA-biodegradation process in Lake Kahokugata, which is induced by the DMA amendment.