Validation of a new formula for predicting the lower flammability limit of hybrid mixtures

A correlation of the lower flammability limit for hybrid mixtures was recently proposed by us. The experimental conditions including ignition energy and turbulence which play a primary role in a gas or dust explosion were at fixed values. The sensitivity of such experimental conditions to the accuracy of the proposed formula was not thoroughly discussed in the previous work. Therefore, this work studied the effect of varying the ignition energy and turbulence intensity to the formula proposed in our previous paper. For ignition energy effect, results from methane/niacin mixture demonstrated that the MEC and LFL will not be affected by changing ignition energy. There is no distinguishable difference among gas explosion index (K_G) and dust explosion index (K_St) derived from tests with every ignition energy (2.5 kJ, 5 kJ and 10 kJ) in a 36 L vessel. The proposed formula is independent of ignition energy. For turbulence effect, the proposed formula can have a good prediction of the explosion and non-explosion zone if the ignition delay time is within a certain range. The formula prediction is good as the ignition delay time increases up to 100 ms in this work. Propane/niacin and propane/cornstarch mixtures are also tested to validate the proposed formula. It has been confirmed that the proposed formula predicts the explosion and non-explosion zone boundary of such mixtures.     

Study of the severity of hybrid mixture explosions and comparison to pure dust-air and vapour-air explosions

The explosion behaviour of heterogeneous/homogeneous fuel-air (hybrid) mixtures is here analysed and compared to the explosion features of heterogeneous fuel-air and homogeneous fuel-air mixtures separately.Experiments are performed to measure the pressure history, deflagration index and flammability limits of nicotinic acid/acetone-air mixtures in a standard 20 L Siwek bomb adapted to vapour-air mixtures. Literature data are also used for comparison.The explosion tests performed on gas-air mixtures in the same conditions as explosion tests of dust-air mixtures, show that the increase in explosion severity of dust/gas-air mixtures has to be addressed to the role of initial level of turbulence prior to ignition.At a fixed value of the equivalence ratio, by substituting the dust to the flammable gas in a dust/gas-air mixture the explosion severity decreases. Furthermore, the most severe conditions of dust-gas/air mixtures is found during explosion of gas-air mixture at stoichiometric concentration.     

Effect of ignition delay on explosion parameters of corn dust/air in confined chamber

This paper presents the explosion parameters of corn dust/air mixtures in confined chamber. The measurements were conducted in a setup which comprises a 5 L explosion chamber, a dust dispersion sub-system, and a transient pressure measurement sub-system. The influences of the ignition delay on the pressure and the rate of pressure rise for the dust/air explosion have been discussed based on the experimental data. It is found that at the lower concentrations, the explosion pressure and the rate of pressure rise of corn dust/air mixtures decrease as the ignition delay increases from 60 ms; But at the higher concentrations, the explosion pressure and the rate of pressure rise increase slightly as the ignition delay increases from 60 ms to 80 ms, and decrease beyond 80 ms. The maximum explosion pressure of corn dust/air mixtures reaches its highest value equal to 0.79 MPa at the concentration of 1000 gm⁻³.     

Experimental study on the minimum explosion concentration of anthracite dust: The roles of O2 mole fraction,inert gas and CH4 addition

The explosion characteristics of anthracite coal dust with/without small amount of CH₄ (1.14 vol %) were investigated by using a 20 L spherical explosion apparatus with an emphasis on the roles of oxygen mole fraction and inert gas. Two methods based on overpressure and combustion duration time were used to determine the minimum explosion concentration (MEC) or the lower explosion limit (LEL) of the pure anthracite coal dust and the hybrid coal-methane mixtures, respectively. The experiment results showed that increasing oxygen mole fraction increases the explosion risk of coal dust: with increasing oxygen mole fraction, the explosion pressure (P_ex) and the rate of explosion pressure rise ((dp/dt)_ex)) increase, while MEC decreases. The explosion risk of anthracite dust was found to be lower after replacing N₂ with CO₂, suggesting that CO₂ has a better inhibition effect on explosion mainly due to its higher specific heat. However, the addition of 1.14% CH₄ moderates the inhibition effect of CO₂ and the promotion effect of O₂ on anthracite dust explosion for some extent, increasing explosion severity and reducing the MEC of anthracite dust. For hybrid anthracite/CH₄ mixture explosions, Barknecht's curve was found to be more accurate and conservative than Chatelier's line, but neither are sufficient from the safety considerations. The experimental results provide a certain help for the explosion prevention and suppression in carbonaceous dust industries.     

Explosibility of cork dust in methane/air mixtures

Explosibility studies of hybrid methane/air/cork dust mixtures were carried out in a near-spherical 22.7 L explosibility test chamber, using 2500 J pyrotechnic ignitors. The suspension dust burned as methane/air/dust clouds and the uniformity of the cork dust dispersion inside the chamber was evaluated through optical dust probes and during the explosion the pressure and the temperature evolution inside the reactor were measured. Tested dust particles had mass median diameter of 71.3 μm and the covered dust cloud concentration was up to 550 g/m³. Measured explosions parameters included minimum explosion concentration, maximum explosion pressures and maximum rate of pressure rise. The cork dust explosion behavior in hybrid methane/air mixtures was studied for atmospheres with 1.98 and 3.5% (v/v) of methane. The effect of methane content on the explosions characteristic parameters was evaluated. The conclusion is that the risk and explosion danger rises with the increase of methane concentration characterized by the reduction of the minimum dust explosion concentration, as methane content increases in the atmosphere. The maximum explosion pressure is not very much sensitive to the methane content and only for the system with 3.5% (v/v) of methane it was observed an increase of maximum rate of pressure rise, when compared with the value obtained for the air/dust system.     

Hybrid H2/Al dust explosions in Siwek sphere

Explosion indices and explosion behaviour of Al dust/H₂/air mixtures were studied using standard 20 l sphere. The study was motivated by an explosion hazard occurring at some accidental scenarios considered now in ITER design (International Thermonuclear Experimental Reactor). During Loss-of-Vacuum or Loss-of-Coolant Accidents (LOCA/LOVA) it is possible to form inside the ITER vacuum vessel an explosible atmosphere containing fine Be or W dusts and hydrogen. To approach the Be/H₂ explosion problem, Be dust is substituted in this study by aluminium, because of high toxicity of Be dusts. The tested dust concentrations were 100, 200, 400, 800, and 1200 g/m3; hydrogen concentrations varied from 8 to 20 vol. % with 2% step. The mixtures were ignited by a weak electric spark. Pressure evolutions were recorded during the mixture explosions. In addition, the gaseous compositions of the combustion products were measured by a quadruple mass-spectrometer. The dust was involved in the explosion process at all hydrogen and dust concentrations even at the combination ‘8%/100 g/m3’. In all the other tests the explosion overpressures and the pressure rise rates were noticeably higher than those relevant to pure H₂/air mixtures and pure Al dust/air mixtures. At lower hybrid fuel concentrations the mixture exploded in two steps: first hydrogen explosion followed by a clearly separated Al dust explosion. With rising concentrations, the two-phase explosion regime transits to a single-phase regime where the two fuel components exploded together as a single fuel. In this regime both the hybrid explosion pressures and pressure rise rates are higher than either H₂ or Al ones. The two fuels compete for the oxygen; the higher the dust concentration, the more part of O2 it consumes (and the more H₂ remains in the combustion products). The test results are used to support DUST3D CFD code developed at KIT to model LOCA or LOVA scenarios in ITER.     

On the transient flow in the 20-liter explosion sphere

The turbulence level in the 20-l explosion sphere, equipped with the Perforated Dispersion Ring, was measured by means of laser Doppler anemometry. The spatial homogeneity of the turbulence was investigated by performing velocity measurements at various locations in the transient flow field. Directional isotropy was investigated by measuring two independent components of the instantaneous velocity. The transient turbulence level could be correlated by a decay law of the form

in which the exponent, n, assumes a constant value of 1.49±0.02 in the period between 60 and 200 ms after the start of the injection process. In this time interval the turbulence was also observed to be homogeneous and practically isotropic. The results of this investigation imply that the turbulence level in the 20-l explosion sphere at the prescribed ignition delay time of ms is not equal to the turbulence level in the 1 m³-vessel. Hence, these results call into question the widely held belief that the cube-root-law may be used to predict the severity of industrial dust explosions on the basis of dust explosion severities measured in laboratory test vessels.     

Explosibility of hydrogen–graphite dust hybrid mixtures

To evaluate the hazard of combined hydrogen/dust explosions under severe accident conditions in International Thermonuclear Experimental Reactor (ITER), standard method of 20-L-sphere was used to measure the explosion indices of 4-μm fine graphite dust in lean hydrogen/air mixtures. The mixtures were ignited by a weak electric spark. The tested fuel concentrations were 8–18 vol% H₂ and 25–250 g/m³ dust. If the hydrogen content is higher than 10 vol%, the dust constituent can be induced to explode by the hydrogen explosion initiated by a weak electric spark. Depending on the fuel component concentrations, the explosions proceed in either one or two stages. In two-stage explosions occurring at low hydrogen and dust concentrations, the mixture ignition initiates first a fast hydrogen explosion followed by a slower phase of the dust explosion. With increasing dust concentration, the dust explodes faster and can overlap the hydrogen-explosion stage. At higher hydrogen concentrations, the hybrid mixtures explode in one stage, with hydrogen and dust reacting at the same time scale. Maximum overpressures of hybrid explosions are higher than those observed with hydrogen alone; maximum rates of pressure rise are lower in two-phase explosions and, generally, higher in one-stage explosions, than those characteristic of the corresponding H₂/air mixtures.     

基于20 L球罐的多相混合物扩散模拟

为更好地探索多相混合物的爆炸特性，以铝粉、乙醚、空气为研究对象，基于20 L球型爆炸罐建立三维计算模型，对气固两相和气液固三相混合物的分散过程进行数值模拟，以分析不同多相混合物分散过程的差异，并为测量多相混合物爆炸下限时的点火延迟时间设定提供参考。监测分析铝粉浓度粒子分布、流场内部湍流动能以及液相体积百分数等的演化过程，讨论混合物分散效果的差异，并确定测量爆炸下限的点火延迟时间。研究结果表明:实验工况下，液相的存在会降低粉尘云团的湍流动能、降低其扩散速度，并使粉尘云内部浓度更均匀。测量多相混合物爆炸下限时，三相混合物的最佳点火延迟时间早于气固两相混合物10~20 ms。     

Experimental studies of ignition and explosions in cyclohexane liquid under oxygen oxidation conditions

The safe operation of hydrocarbon liquid-phase oxidation by air or oxygen requires the knowledge on the flammability of hydrocarbon/oxygen mixtures in both the vapor space and vapor bubbles. The latter is of particular importance in situation where pure oxygen is used as the oxidant as most bubbles are expected to be flammable and explosive. New experimental findings are presented for ignition and explosion in cyclohexane liquid under oxygen oxidation conditions. A bubble column is constructed and fitted with multiple igniters. Experiments were performed at liquid temperatures between 373.15 and 423.15 K under various flow rates of pure oxygen. Two drastic different ignition and explosion behaviors were observed. The first is a typical bubble explosion from the direct ignition of the flammable bubbles in the liquid. The explosion occurs immediate following the ignition and do not produce significant energy that endanger the system. The other is a remote, delayed ignition and explosion in the vapor space that can produce significant overpressure and endanger the system. The explosion is attributed to the ignition of flammable vapor space by active free radicals from cyclohexyl hydroperoxide decomposition. A mechanism is proposed for the remote, delayed ignition to occur in the oxidation system. It is concluded that explosion in an oxidizing, bubbly liquid is not only a likely scenario but also a severe scenario, and cyclohexane oxidation should not be carried out directly with pure oxygen and without any inerting.     

点火延迟时间对甘薯粉尘爆炸的影响研究

为了预防甘薯粉尘爆炸事故的发生,本文研究点火延迟时间对甘薯粉尘爆炸的影响规律,利用20 L球形爆炸仪研究甘薯粉尘的爆炸特性及其在200 g/m3,500 g/m3和800 g/m3质量浓度下通过改变点火延迟时间的爆炸规律。结果表明:粉尘的最佳点火延迟时间与浓度有关,在该点火时间下所测得的最大爆炸压力均高于在固定点火延迟时间下的测量值,60 ms的固定点火延迟时间不适用于甘薯粉尘爆炸测试。     

Study of dust cloud behaviour in the modified Hartmann tube using the image subtraction method (ISM)

A dispersion of fine particles in the air is needed for a dust explosion to occur since an explosion is the fast combustion of particles in the air. When particles are poorly dispersed, agglomerated, or their concentration is low, the combustion velocity decreases, and deflagration would not occur. The combustion rate is strictly related to dust concentration. Therefore, the maximum explosion pressure rise occurs at dust concentration close to stoichiometric. Conversely, Minimum Explosion Concentration (MEC) is the lower limit at which self-sustained combustion and a pressure rise are possible. Dust explosion tests are designed to reproduce the dispersion and generation of dust clouds in industrial ambiences by using dispersion devices activated by pressurised air pulses. The resulting dust cloud, which has a marked transient character, is considered representative of real clouds by current standards. Over time, several studies have been carried out to optimise these devices (e.g. to reduce the inhomogeneity of the cloud in the 20 L sphere). The Minimum Ignition Energy (MIE) of dust is measured using the Mike3 modified Hartmann tube, where the ignition attempt is made 60–180 ms after dust dispersion regardless of dust characteristics.This work investigates the dust clouds’ actual behaviour inside the modified Hartmann tube before ignition using high-velocity video movies and a new image post-treatment method called Image Subtraction Method (ISM). Movies are recorded with high-speed cameras at a framerate of 2000 fps and elaborated with an on-purpose developed LabVIEW® code. Concentration (mass per volume) and dispersion pressure are varied to evaluate their effect on dust clouds. Maise starch, iron powder and silica powder are chosen to investigate the effect of particle density and size on the cloud structure and turbulence. This approach will help to investigate the structure of the dust cloud, the shape and size of the particle lumps and the change in dust concentration over time. In addition, information on the actual concentration and cloud turbulence at the ignition location and delay time were obtained, which may help identify the local turbulence scale and widen the characterisation of the cloud generated in the Hartmann tube.     

基于正交实验的面粉爆炸特性研究

为探究面粉爆炸实验中粉尘质量浓度、点火能量、点火延迟时间对面粉爆炸的影响,采用正交实验法并利用20 L球形爆炸测试装置比较研究了粉尘质量浓度、点火延迟时间以及点火能对面粉爆炸的影响程度.结果表明:对最大爆炸压力影响最为显著的因素是点火延迟时间,对最大爆炸指数影响最为显著的因素是粉尘质量浓度;在实验浓度范围内,存在最佳实...     

Study of the explosion parameters of vapor–liquid diethyl ether/air mixtures

The knowledge of the vapor–liquid two-phase diethyl ether (DEE)/air mixtures (mist) on the explosion parameters was an important basis of accident prevention. Two sets of vapor–liquid two-phase DEE/air mixtures of various concentrations were obtained with Sauter mean diameters of 12.89 and 22.90 μm. Experiments were conducted on vapor–liquid two-phase DEE/air mixtures of various concentrations at an ignition energy of 40.32 J and at an initial room temperature and pressure of 21 °C and 0.10 MPa, respectively. The effects of the concentration and particle size of DEE on the explosion pressure, the explosion temperature, and the lower and upper flammability limits were analyzed. Finally, a series of experiments was conducted on vapor–liquid two-phase DEE/air mixtures of various concentrations at various ignition energies. The minimum ignition energies were determined, and the results were discussed. The results were also compared against our previous work on the explosion characteristics of vapor–liquid two-phase n-hexane/air mixtures.     

The influence of air flow on maximum explosion characteristics of dust–air mixtures

A standard spherical apparatus for measuring explosion characteristics was modified to give increased and controlled turbulence within a dust–air mixture. This was intended to mimic the local effects which may occur during industrial dust explosions, particularly secondary ones which may develop in ducts or mine galleries where the initial explosion causes an increased air velocity and suspension of further quantities of dust.The results show that there may be a doubling of the maximum explosion pressure and of the rate of pressure rise during the explosion under more turbulent conditions. This is significant for modelling of dust explosions and suggests that explosion relief may be inadequate if this factor is not taken into consideration.The modified apparatus therefore gives a laboratory method for assessing the effect of turbulence in dust explosions.     

Minimum ignition temperatures and explosion characteristics of micron-sized aluminium powder

To forestall, control, and mitigate the detrimental effects of aluminium dust, a 20-L near-spherical dust explosion experimental system and an HY16429 type dust-cloud ignition temperature test device were employed to explore the explosion characteristics of micron-sized aluminium powder under different ignition energies, dust particle sizes, and dust cloud concentration (C_dust) values; the minimum ignition temperature (MIT) values of aluminium powder under different dust particle sizes and C_dust were also examined. Flame images at different times were photographed by a high-speed camera. Results revealed that under similar dust-cloud concentrations and with dust particle size increasing from 42.89 to 141.70 μm, the MIT of aluminium powder increased. Under various C_dust values, the MIT of aluminium dust clouds attained peak value when concentrations enhanced. Furthermore, the increase of ignition energy contributed to the increase of the explosion pressure (P_ex) and the rate of explosion pressure rise [(dP/dt)_ex]. When dust particle size was augmented gradually, the P_ex and (dP/dt)_ex attenuated. Decreasing particle size lowered both the most violent explosion concentration and explosive limits.     

A constant pressure dust explosion experiment

A new apparatus has been designed for investigating flame propagation in turbulent dust clouds at near constant pressure conditions. The experimental approach is inspired by the classical soap bubble method for measuring burning velocities in gaseous mixtures. Combustible dust is dispersed with pressurised air to form an explosive mixture inside a transparent latex balloon. After a certain delay time, the turbulent dust cloud is ignited by a 40 J chemical igniter. A digital high-speed video camera records the propagating flame and the expansion of the balloon. Experiments were performed with two types of dust, Lycopódium spores and maize starch, as well as with propane–air mixtures under initially quiescent or turbulent conditions. Although the results are primarily qualitative in nature, they nevertheless demonstrate fundamental differences between premixed combustion of gaseous mixtures, and ‘premixed combustion with non-premixed substructures' in mechanical suspensions of solid particles dispersed in air. The discussion highlights some fundamental challenges for future dust explosion research.     

Experiments on the influence of pre-ignition turbulence on vented gas and dust explosions

Experiments were performed on the influence of pre-ignition turbulence on the course of vented gas and dust explosions. A vertical cylindrical explosion chamber of approximately 100 l volume and a length-to-diameter ratio (l/d) of 4.7 consisting of a steel bottom segment and three glass sections connected by steel flanges was used to perform the experiments. Sixteen small fans evenly distributed within the chamber produced turbulent fluctuations from 0 to 0.45 m/s. A Laser-Doppler-anemometer (LDA) was used to measure the flow and turbulence fields. During the experiments the pressure and in the case of dust explosions the dust concentration were measured. In addition, the flame propagation was observed by a high-speed video camera. A propane/nitrogen/oxygen mixture was used for the gas explosion experiments, while the dust explosions were produced by a cornstarch/air mixture.It turned out that the reduced explosion pressure increased with increasing turbulence intensity. This effect was most pronounced for small vents with low activation pressures, e.g. for bursting disks made from polyethylene foil. In this case, the overpressure at an initial turbulence of 0.45 m/s was twice that for zero initial turbulence.     

Lower explosion limit of hybrid mixtures of burnable gas and dust

Hybrid mixtures – mixtures of burnable dusts and burnable gases – pose special problems to industries, as their combined Lower Explosion Limit (LEL) can lie below the LEL of the single substances. Different mathematical relations have been proposed by various authors in literature to predict the Lower Explosion Limit of hybrid mixtures (LEL_hybrid). The aim of this work is to prove the validity or limitations of these formulas for various combinations of dusts and gases. The experiments were executed in a standard 20 L vessel apparatus used for dust explosion testing. Permanent spark with an ignition energy of 10 J was used as ignition source. The results obtained so far show that, there are some combinations of dust and gas where the proposed mathematical formulas to predict the lower explosible limits of hybrid mixtures are not safe enough.     

点火延迟时间对粉尘最大爆炸压力测定影响的研究

根据粉尘云形成时颗粒分散及沉降的时间效应,指出目前国际通行的球型爆炸装置采用固定点火延迟时间测定粉尘最大爆炸压力的方法具有不确定性,并以煤粉为介质在20 L标准爆炸球装置上进行系列爆炸实验,研究装置点火延迟时间对粉尘爆炸压力的影响。结果表明:点火延迟时间对粉尘爆炸压力测定有十分显著的影响,不同粒径粉尘的最大爆炸压力有不同点火延迟时间,目前仅以气相湍流度所确定的固定点火延迟时间下,所测粉尘最大爆炸压力可能严重偏离实际。