EDTA在铅污染土壤治理中的优化处理方法

为了探究EDTA在土壤重金属污染治理中的优化处理方法,采用湿筛和水中重力沉降的方法,从人工Pb污染土壤(原土)中分离提取砂土、粉土和粘土,分析讨论了EDTA对土壤中Pb的去除效果,并从EDTA清洗前后土壤中Pb的BCR形态分布出发,分析了EDTA对不同粒径土壤中各形态Pb的去除效果。研究发现,实验用土壤中砂土、粉土和粘土含量分别为11.2%、75.6%和13.2%,EDTA浓度越高,土壤中Pb去除效果越好,且砂土中Pb最易被去除(~100%),粉土与原土其次(88.66%~96.50%),粘土最难被去除(64.78%~79.60%),但随着EDTA浓度增加,粒径对去除Pb的影响减弱。在土壤修复实践中,可通过利用不同浓度EDTA处理不同粒径土壤的方法达到优化效果。BCR形态分布说明外源性Pb进入土壤后主要以弱酸提取态和可还原态存在,EDTA清洗主要去除弱酸提取态和可还原态,粘土中的各形态去除率均最小。     

铅锌厂重金属污染土壤的螯合剂淋洗修复及其应用

为探讨螯合剂淋洗法在修复铅锌厂周边重金属污染土壤的修复效果及淋洗后土壤利用价值,研究采用振荡淋洗的方法比较了乙二胺四乙酸(EDTA)、次氮基三乙酸三钠盐(NTA)、[S,S]-乙二胺-N,N-二琥珀酸三钠盐(EDDS)乙二醇-双-(2-氨基乙醚)四乙酸(EGTA)4种螯合剂对不同污染程度土壤中Cd、Cu、Zn、Pb的去除效果,并用BCR连续提取法分析了淋洗前后土壤重金属形态的变化,最后通过黑麦草盆栽实验及土壤酶分析,探讨了土壤经淋洗后的利用价值。结果表明,4种螯合剂中EDTA对Cd、Cu、Zn和Pb的去除率比其他螯合剂的去除率高,其中对高污染土壤4种重金属离子的去除率最大,分别为Cd 90.98%、Cu 42.10%、Zn 56.98%和Pb 52.03%,4种重金属中Cd的去除效果分别为EDTANTAEDDSEGTA;EDTA能有效去除酸溶态、可还原态土壤重金属,而对可氧化态和残余态土壤重金属作用效果不明显;EDTA淋洗土种植黑麦草后土壤脱氢酶、碱性磷酸酶和β-葡糖苷酶活性均高于NTA淋洗后土壤中酶活性。综合考虑淋洗效率、淋洗剂的成本和利用价值等因素,可以认为,采用EDTA和NTA淋洗修复重金属污染土壤具有一定的实用性,并以EDTA效果较佳。     

超声强化淋洗修复Pb、Cd、Cu复合污染土壤

针对传统淋洗法修复土壤中重金属效率较低的问题,研究了超声强化淋洗技术以提高重金属去除率。以铅(Pb)、镉(Cd)、铜(Cu)为目标污染物,在0.05 mol·L~(-1)柠檬酸、0.05 mol·L~(-1)EDTA和0.05 mol·L~(-1)皂角苷作为淋洗剂条件下,使用传统振荡、超声强化以及超声波加振荡3种不同的作用方式,对Pb、Cd、Cu的去除率进行比较,并对3种不同淋洗方式后Pb、Cd、Cu的形态变化进行了探讨。结果表明,当使用柠檬酸和皂角苷作为淋洗剂进行振荡淋洗时,重金属洗脱效果不理想。超声对于强化柠檬酸洗脱效果并不明显,而对于强化皂角苷洗脱重金属效果明显,平均去除率提高了120.47%。当淋洗剂为EDTA时,土壤样品在传统振荡2 h作用下,对Pb、Cd、Cu的去除率依次为50.33%、76.65%和47.35%,而在超声波30 min条件下对Pb、Cd、Cu的去除率依次为82.19%、83.31%和53.89%,平均去除率高出28.60%,可显著提高重金属去除率,缩短淋洗时间。但超声波30 min加传统振荡2 h相较于单纯超声强化效果提升不明显。通过对比3种淋洗方式后土壤中的Pb、Cd、Cu形态发现,酸可提取态的重金属在超声强化作用后有明显降低,同时超声强化对于铁锰氧化物结合态、有机物结合态和残渣态也具有较好的去除能力。因此,超声强化在化学淋洗中的应用具有一定的可行性,是一种简单、极快速去除污染场地中重金属Pb、Cd、Cu的增效手段。     

超声波协同Fenton氧化法去除造纸法再造烟叶废水COD

采用单独Fenton氧化法和联合超声波Fenton氧化法去除经过生化处理后的造纸法再造烟叶废水COD,通过研究反应时间、H2O2和Fe2+用量对COD去除率的影响,确定最佳实验条件。结果显示,Fenton法和联合超声波Fenton法对COD最大去除率分别为66.18%和76.99%;对比结果发现,超声波可以减少Fenton反应时间,降低COD去除率最大时的Fenton试剂用量,保证高COD去除率的同时扩宽Fenton试剂用量范围,超声波协同Fenton反应的作用显著。     

EDTA/纳米羟基磷灰石联合修复重金属污染土壤

土壤淋洗可能导致残留重金属活化,采用淋洗/钝化联合修复重金属污染土壤可在一定程度上减少这一影响。研究了EDTA淋洗、纳米羟基磷灰石钝化及两者联合修复对土壤重金属洗脱率、TCLP浸出浓度、化学形态分布的影响,构建了涵盖土壤重金属残留量、生物有效性和生理毒性的环境风险评价方法,对淋洗、钝化及其联合修复进行了评价。结果发现,EDTA淋洗对Pb和Cu的洗脱效果较好,对Zn浸出浓度的削减率较高。当EDTA投加量为2 g·L~(-1)时,Zn的浸出浓度降低了70.40%。纳米羟基磷灰石对Pb和Zn具有较好的钝化效果,对Cu和Cd的钝化作用相对较弱。当纳米羟基磷灰石投加量为2%时,Pb浸出浓度削减率高达89.65%。淋洗/钝化联合修复大幅度降低了Pb和Cd的浸出浓度,降低了可还原态Cu残留量、可还原态和残渣态Cd残留量,以及弱酸提取态和可还原态Zn、Pb残留量。当EDTA和纳米羟基磷灰石投加量分别为1 g·L~(-1)和1%时,土壤重金属总环境风险削减率达到74.12%。EDTA对土壤中Cu和Cd的洗脱效果较好,后续钝化修复作用有限,Pb和Zn则可通过淋洗/钝化联合修复大幅度提高削减环境风险削减率。     

铅污染土壤电动修复增强技术的研究

利用电动修复技术对铅污染土壤的修复进行了实验室研究,研究了修复时间和络合剂EDTA对电动修复效果的影响,分析了土壤重金属的迁移和变化特征。结果表明,在电场力作用下随着修复时间的增长污染物的去除率相应提高,去除率由修复时间5 d时的13%增加到15 d时的20%。以EDTA作为阴极控制液,EDTA可与硝酸铅反应形成溶解态的络合物,提高铅离子的移动性,从而提高修复效果。随着EDTA浓度由0.1 mol/L到0.2 mol/L,Pb的去除率由44.4%提高到61.5%,说明添加络合剂可以提高修复效果。另外,电动修复效果与铅的形态分布有密切关系,交换态和碳酸盐结合态有利于重金属铅的去除。     

环境友好型淋洗剂对重金属污染土壤的修复效果

以广西某废弃铅锌冶炼企业重金属复合污染土壤为对象,采用土柱淋洗的方法,分别将自制的茶皂素、柠檬酸和EDTA 3种淋洗剂进行复合淋洗,并对复合淋洗的最佳配比、淋洗剂添加方式和淋洗时间进行研究,得到对环境友好且淋洗效果好的复合淋洗剂。最后,对淋洗前后土壤中Cu、Pb和Zn的赋存形态进行研究,探讨淋洗机理。研究结果表明,茶皂素和柠檬酸复合时对重金属Cu、Pb、Zn的去除率分别达到了77.00%、52.09%和58.66%,综合考虑淋洗效率以及经济环保等因素,选择将茶皂素和柠檬酸复合进行淋洗。复合淋洗实验结果表明,柠檬酸和茶皂素体积比为3∶1复合方式淋洗30 h,淋洗效果最佳,对重金属Cu、Pb和Zn的去除率分别达到82.77%、65.49%和78.12%。茶皂素和柠檬酸复合淋洗能有效的去除土壤中酸可提取态和有机结合态的重金属,氧化物结合态的Pb和Zn也有较大程度的降低,同时还发现,茶皂素和柠檬酸共同作用对残余态的Pb去除效果也较好,可达到50%以上。从茶籽饼中提取茶皂素与天然有机酸柠檬酸复合淋洗,用于修复污染面积小、污染浓度高且污染比较集中的重金属污染土壤,效果好且对环境友好。     

EDTA对土壤中Pb的赋存形态分布的影响及其环境意义

研究了 EDTA淋洗重金属污染土壤前后 Pb的赋存形态的分布变化。结果表明 ,EDTA淋洗后的土壤中 Pb主要以残渣态和酸可提取态存在。酸可提取态 Pb含量的增加对于运用植物提取技术修复 Pb污染的土壤是有利的     

阳极pH对Fe(Ⅲ)强化阴极电动修复Pb污染土壤的影响

土壤的pH值对电动力修复技术至关重要。利用Fe(NO3)3作为阴极电解液,不仅可以消耗电解产生的OH-,不会对土壤造成二次污染,并且修复后土壤的pH相对较低。在土壤室和阴极室之间添加活性炭纤维和阳离子膜,增强修复效果。采用配制的Pb污染土壤,在电场强度为1 V·cm-1的条件下进行实验,研究不同pH(3、4、5)的柠檬酸-柠檬酸钠阳极电解液对电动力学修复Pb污染土壤效果的影响。结果表明:在利用Fe(Ⅲ)-活性炭纤维强化电动修复时,添加的阳极电解液pH值越小,Pb的去除效果越好;各阳极电解液pH值递增梯度相对应Pb的截面最大去除率分别为:80.53%、53.1%和40.69%。通过分析残留在土壤中Pb的重金属形态,得到在距离阳极4 cm处的土壤截面中Pb主要以较稳定的、环境毒性较低的有机态和残渣态存在。     

不同化学淋洗剂对复合重金属污染土壤的修复机理

化学淋洗技术是一种常用的重金属污染土壤修复技术,化学淋洗剂的选择尤为重要。以乙二胺四乙酸二钠(EDTA),柠檬酸(CA)和三氯化铁(FeCl_3)为化学淋洗剂,采用振荡淋洗法研究淋洗时间与淋洗剂浓度对Cu、Zn、Pb和Cd去除效果的影响,分析重金属污染土壤淋洗前后重金属形态与基本理化性质的变化。结果表明:3种化学淋洗剂对重金属的快速反应阶段基本在60 min内,在240 min达到淋洗平衡,对Pb和Cd的淋洗主要是非均相扩散过程;EDTA、柠檬酸和FeCl_3对重金属的去除能力依次为PbCdCuZn,CdZnCuPb与Pb≈CdCuZn,EDTA的淋洗效率最高,Cd的解吸能力最强;EDTA和FeCl_3可有效去除弱酸可溶态与可还原态重金属,柠檬酸能有效去除弱酸可溶态重金属,修复后的土壤仍有环境风险;3种淋洗剂修复后的土壤中总有机碳与粒径分布无明显变化,FeCl_3会酸化土壤。综合考虑,EDTA、柠檬酸和FeCl_3均为淋洗效果好的环境友好型化学淋洗剂,该研究成果可用于现场淋洗去除土壤中重金属的小试。     

Optimization of Height of Release of Air Pollutants

A number of key projects in the Environmental Protection Agency (EPA) particulate R&;D program having applicability to industry are presented. For electrostatic precipitators (ESP) there is presented the result of work on large diameter discharge electrodes which provide a decrease in penetration of up to a factor of 4 when compared to conventional small diameter electrodes. Also discussed is the multistage ESP which provides a collection efficiency that would require a collecting plate area 4 or 5 times larger with conventional ESP technology. The E-SOX technology makes use of the multistage concept to free up space in the ESP for SO₂ removals of up to 90%. Electrostatically augmented fabric filtration provides a reduction in pressure drop of about 5 0% as compared to conventional fabric filtration. Wind tunnel modeling of windbreaks for material storage piles indicates a potential for providing engineering design data that would allow significant emission reduction caused by wind erosion     

Investigation of the characteristics of the reflectivity of clouds

This paper investigates some of the reflectivity characteristics that clouds (when modelled as solid bodies) must exhibit to be compatible with observations that the reflecting surface of a cloud (i) appears almost equally bright across its face, (ii) is brightest when the cloud is opposite to the Sun but decreases in brightness as the cloud moves to other positions and (iii) increases in brightness with increasing optical thickness of the cloud in the observer's line of sight. These observations, respectively, are shown to imply that the peak value of the bidirectional total reflectivity from a cloud surface (i) increases in inverse proportion to the cosine of the angle between the Sun and the normal to the cloud surface, as the incident angle increases, (ii) appears to be directed back in the direction of the incident radiation, and (iii) increases as optical thickness of the cloud in the observer's line of sight increases. The results could have application in many fields (e.g. modelling diffuse radiance distributions for cloudy skies).     

实验室质量管理体系内部审核的实施

在实施ISO／IEC17025：1999标准《检测和校准实验室能力的通用要求》过程中，通过实验室质量管理体系内部审核的实践与系统分析，识别出内部审核实施阶段的关键环节，提出召开首次会议、收集审核证据、确定审核发现和召开末次会议的技术方法，对提高内部审核的质量和有效性、获得可靠的审核结论具有重要意义。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

扬中生态环境建设的思考与实践

结合扬中生态环境的基本情况和存在的不足，进行了具体分析，对扬中未来生态建设的发展方向提出了建议及实施措施。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Comparison of methods for evaluation of activity of photocatalytic films

Objective

This work aims to investigate the correlation between the photocatalytic activity determined by methylene blue bleaching (DIN 52980), stearic acid degradation, and degradation of acetone in gas phase.

Method

The photocatalytic TiO₂ coatings included in this investigation ranged from thin commercially available coatings (Activ^TM and BioClean^TM) and ready to use suspensions (Nano-X PK1245) to lab-produced PVD and sol?Cgel coatings. XRD analysis of the photocatalytic coatings showed that all the coatings consisted of nanocrystalline anatase, although the thickness and porosity varied considerably.

Results

The study showed that the reproducibility of the activity measurements was good. However, more importantly, the investigation showed that there is a good correlation between the activities determined by the different methods even though the characteristics of the photocatalytic coatings and the organic probe molecules varied considerably.

Conclusion

The overall findings of this work suggest that there is a good correlation between the investigated methods. These results are promising for the future work concerning standardization of methods for determination of the activity of photocatalytic films.     

Impact of overexploitation of shellfish: northeastern coast of India

India has a very extensive coastline of about 7515 km, rich in diverse living resources. These resources continue to deteriorate with rampant harvesting or are altered for other uses such as aquaculture and fisheries. The present paper deals with degrading coastal habitats in northeastern India, and projects the intensity of the stress arising from the collection of tiger prawn seeds (Penaeus monodon) for aquacultural farms and molluskan shells for poultry feed and edible lime. Indiscriminate exploitation of these resources leads to a heavy reduction of the species concerned and other associated marine communities. The magnitude of such destruction has been quantified. The impacts of biodiversity loss and their after-effects on the ecobalance of this coastal system have become a matter of great concern to ecologists to maintain security and sustainability. The authors propose a public awareness program on themes relating to the importance of biodiversity for human livelihoods.