强化UV/Fenton法降解水中苯酚的研究

研究了UV/Fenton法处理含苯酚废水时H2 O2 和FeSO4 加入量及苯酚初始浓度对酚去除效果的影响及C2 O2 -4 对UV/Fenton法的增强效果。 [H2 O2 ]=2 0mmol/L ,[FeSO4 ]=5mmol/L ,反应 2 0min ,苯酚初始浓度为 5 0mg/L时 ,酚去除率达 99%。UV/Fenton体系中引入C2 O2 -4 后可有效提高对紫外和可见光的利用率 ,进而提高了对高浓度苯酚废水去除效果     

UV／Fenton法处理酸性红B研究

采用UV／Fenton高级氧化技术对酸性红B模拟废水进行处理，当进水浓度为400mg／L时，确定了各影响因素的最佳投加量：H2O2投加量为2mL／L，Fe^2＋投加量为0．08g／L，最佳pH值为4；并采用一级动力学公式对酸性红B降解速率进行拟合，研究了反应条件对速率常数的影响。最后通过对单独UV法、单独Fenton法和UV／Fenton法3种处理方法效果的比较，发现UV与Fenton试剂具有协同作用。     

UV／草酸铁／H2O2法处理乙草胺废水的研究

对UV／草酸铁／H2O2法处理乙草胺废水进行研究，考察了H2O2浓度、FeSO4浓度、K2C2O4浓度、pH值及反应时间对乙草胺去除效果的影响。结果表明，当H2O2／FeSO4／K2C2O4(化学剂量数比)=50：5：1，H2O2／乙草胺初始COD(质量浓度比)=3：1时，该技术对乙草胺的去除率可达85％以上。这表明，采用UV／草酸铁／H2O2法可以有效地处理含乙草胺废水。     

磁强化次氯酸钠氧化法处理邻硝基苯酚废水的实验研究

利用磁强化次氯酸钠氧化法对邻硝基苯酚废水进行了处理实验研究。结果表明,对于质量浓度为250mg／L、CODCr为2000mg／L、色度为150倍的100mL邻硝基苯酚废水,当次氯酸钠（2．5％）用量8mL、颗粒活性炭用量200mg、溶液pH为6．0、反应时间5min时,邻硝基苯酚的去除率达94．4％,CODCr的去除率达94．2％,色度的去除率达100％。采用外加磁场,当磁场强度为60mT时,邻硝基苯酚和CODCr达到相同的去除率,反应时间缩短了3min,显著提高了反应效率。同时对磁强化氧化法的机理进行了理论上的分析。     

紫外光助O3、H2O2氧化降解炼油废碱水的可行性实验

炼油高浓度有机废碱水是石化行业中很难降解的废水。本实验用光化学氧化技术对其进行了降解研究，比较了紫外光／空气、紫外光／O3、紫外光／空气／H2O2系统的处理效果。结果表明，光化学氧化技术降解此废水是可行的，紫外光可使废水中COD、油、酚的降解率明显提高。当废水中O3的投加量每小时为22mg／L，或H2O2投加量为1％／L时，UV／O3法与UV／空气／H2O2法的降解效果相近。同时，通过控制O，浓度或H2O2的投加量等条件，可使废水中COD、油、酚和硫化物降解到地方污染物二级排放标准。     

O3氧化工艺处理黄连素制药废水研究

采用臭氧（O3）氧化法处理含高浓度黄连素和COD的制药废水,探讨了废水初始pH、O3投加量及初始黄连素浓度等因素对O3氧化过程的影响,确定了O3氧化技术处理黄连素制药废水的最佳操作条件。结果表明,O3能够有效分解废水中的黄连素,降低其COD浓度;黄连素浓度为700mg／L、COD为3500mg／L、pH为0．88的废水,进气O3浓度为14．05mg／（L·min）,处理时间为180rain（即投加量为2529mg／L）时,黄连素和COD的降解率分别可达77．46％和41．28％,BOD,／COD比（B／C比）从0．06提高到0．34,增加了4．7倍;随着废水中初始黄连素浓度的升高,废水COD降解率逐渐降低。O3氧化法是一种有效的黄连素制药废水预处理技术,可以大大提高废水的可生化性。     

臭氧与TiO2/UV协同降解对氯苯酚

利用O3／UV、TiO2／UV和O3／TiO2／UV降解对氯苯酚表明，臭氧与TiO2／UV具有明显的协同作用，如在本实验条件下降解5min后，上述3者对对氯苯酚的去除率分别为55％、10％和77%。O3／TiO2／UV协同作用的本质是由于臭氧能带走二氧化钛光致电子空穴对中的电子，从而产生了更多的羟基自由基，加速了有机物的降解。     

超声波-光催化氧化降解邻氯苯酚的研究

对超声波-光催化氧化降解邻氯苯酚(2-cp)进行了研究,探讨了溶液初始pH值、TiO2投加量、H2O2投加量和溶液初始浓度对邻氯苯酚降解率的影响.并对几种不同处理方法降解邻氯苯酚的结果进行了对比.结果表明,超声波和紫外光的协同效果明显,在相同的反应时间内,超声波能够明显提高光催化降解邻氯苯酚的降解率.超声波和紫外光连用,具有良好的工业应用前景.     

电催化氧化法降解苯酚废水的实验研究

应用自制电化学反应器对废水中苯酚的电催化氧化处理进行了研究，实验了阳极材料、电流密度、电解时间、电极间距离、废水pH值、废水电导率等对苯酚电解去除效果的影响，确定了最佳的处理条件。在电流密度为30mA／cm^2,电解时间为80min，电极间距离为2cm，废水pH值在7～8之间，废水电导率为1100μs／cm的处理条件下，苯酚的电解处理去除率可达97％以上。利用TOC测定仪、紫外光谱和红外光谱等仪，器分析的方法对苯酚降解过程中的产物进行了分析。     

O3／UV氧化法处理电镀含氰废水的试验研究

试验研究了臭氧／紫外光(O3／UV)处理电镀含氰废水的各种操作条件，O3通入量、溶液pH值等因素对除氰效果的影响，结果表明，O3与UV相结合对去除氰化物具有协同效应，该法对氰化物的去除率可达99．9％。     

O3、H2O2／O3及UV／O3在焦化废水深度处理中的应用

采用O3、H2O2／O3及UV／O3等高级氧化技术（AOPs）对某焦化公司的生化出水进行深度处理,考察了O3与废水的接触时间、溶液pH、反应温度等因素对废水COD去除率的影响,确定出O3氧化反应的最佳工艺参数为：接触时间40min,溶液pH8．5,反应温度25℃,此条件下废水COD及UV254的去除率最高可达47．14％和73．47％;H2O2／O3及UV／O3两种组合工艺对焦化废水COD及UV254的去除率均有一定程度的提高,但H2O2／O3系统的运行效果取决于H2O2的投加量。研究结论表明,单纯采用COD作为评价指标,并不能准确反映出O3系列AOPs对焦化废水中有机污染物的降解作用。     

Preparation of biofilm electrode with Xanthomonas sp. and carbon nanotubes and the application to rapid biochemical oxygen demand analysis in high-salt condition

A Xanthomonas sp. was isolated from the sludge on the drain outlet of a pharmaceutical factory. Then, the bacterium and carbon nanotubes (CNTs) were co-attached to an oxygen electrode for rapid analysis of biochemical oxygen demand (BOD). The response current was linear with BOD values in the range 10 to 300 mg/L for standard BOD solution with a response time of 35 seconds (R = 0.9994) and 20 to 580 mg/L for pharmaceutical wastewater with a response time < or =200 seconds (R = 0.9985), which means that this modified electrode might be used for online BOD analysis of pharmaceutical wastewater. Further studies revealed that the modified electrode can be used for BOD measurement in a high-salt condition. Also, the bacterium/CNTs biofilm can maintain its activity and good performance, even after being sealed and stored at 4 degrees C for 50 days.     

臭氧/ 生物活性炭深度处理循环养殖废水

随着工厂化循环水养殖的不断发展,高浓度循环养殖废水对环境污染日益严重.为实现环境友好和资源节约,采用臭氧/生物活性炭对循环养殖废水进行深度处理中试研究.实验结果表明,臭氧化臭氧最佳投加量为4 mg/L,显著增强水体的可生化性,使TOC(总有机碳)/UV254(在波长为254 nm处的单位比色皿光程下的紫外吸光度)提高80%.臭氧/生物活性炭对循环养殖废水中的有机物和氨氮具有良好的去除效果.臭氧/生物活性炭对TOC、高锰酸盐指数和UV254的最终去除率比生物活性炭分别高11.9%、13.4%和6.5%.臭氧/生物活性炭和生物活性炭对氨氮的最终去除率分别为96.0%、90.7%.     

模拟阳光下Ag／I-TiO2光催化预处理山核桃加工废水

研究了在模拟太阳光下,采用银修饰的碘掺杂二氧化钛光催化剂（Ag／I—TiO2）对某食品厂山核桃加工废水进行光催化预处理的效果。结合x射线衍射（XRD）、比表面积分析（BET）、紫外-可见漫反射光谱（uV—Vis）的表征结果,来分析催化剂结构对于废水处理效果的影响。探讨了Ag含量、废水初始pH（pHi）和光照时间等因素对化学需氧量（COD）去除及水质可生化性（B／C）提高的影响。并得出适宜的反应参数为：3％Ag含量;pHi为6;光照时间为240min。在最佳条件下,COD去除率45％,废水B／C比由0．17上升到0．31。光催化氧化法能够有效降低山核桃加工废水的COD含量,并达到显著提高废水可生化性的目的。     

组合方法去除新型采油污水中有机污染物的研究

含聚丙烯酰胺采油污水的有效处理是近年来困扰油田三次采油生产的一个难题。研究采用移动床生物膜技术与O3/UV/H2O2高级氧化技术的组合方法来处理含聚丙烯酰胺采油污水。实验结果表明,移动床生物膜技术可以有效去除污水中的石油类有机物,但对聚丙烯酰胺几乎无效果。O3/UV/H2O2高级氧化技术可以降解污水中的聚丙烯酰胺。组合方法处理后的含聚丙烯酰胺采油污水水质可以达到污水综合排放标准中的一级要求。     

模拟阳光下Ag/I-TiO_2光催化预处理山核桃加工废水

研究了在模拟太阳光下,采用银修饰的碘掺杂二氧化钛光催化剂(Ag/I-TiO2)对某食品厂山核桃加工废水进行光催化预处理的效果。结合X射线衍射(XRD)、比表面积分析(BET)、紫外-可见漫反射光谱(UV-Vis)的表征结果,来分析催化剂结构对于废水处理效果的影响。探讨了Ag含量、废水初始pH(pHi)和光照时间等因素对化学需氧量(COD)去除及水质可生化性(B/C)提高的影响。并得出适宜的反应参数为:3%Ag含量;pHi为6;光照时间为240 min。在最佳条件下,COD去除率45%,废水B/C比由0.17上升到0.31。光催化氧化法能够有效降低山核桃加工废水的COD含量,并达到显著提高废水可生化性的目的。     

Reactions of the amine-containing drugs fluoxetine and metoprolol during chlorination and dechlorination processes used in wastewater treatment

The reactivities of the amine-containing pharmaceuticals fluoxetine and metoprolol with hypochlorite were studied using conditions that simulate wastewater disinfection including neutral pH (7.0), a range of reaction times (2–60 min), and a molar excess of hypochlorite relative to the pharmaceutical concentration (5.7 times). The reactions were monitored using liquid chromatography (LC) with several detection modes including ultraviolet absorbance (UV), mass spectrometry (MS), and post-column reaction/reductive electrochemistry (EC) for determining active chlorine products. At levels of 10 μM, both compounds reacted rapidly (<2 min) to form principally N-chloramine products that were stable in aqueous solution for at least 1 h. The reaction was also studied in wastewater, and similar reactivity was noted. These results demonstrate that the cations fluoxetine and metoprolol are likely to be rapidly transformed into neutral N-chloramines during wastewater disinfection. The reactivity of the N-chloramines was also studied with sulfite to simulate dechlorination, which is often employed in wastewater treatment. Both N-chloramines reacted slowly with sulfite. In the pure water dechlorination experiments, it was estimated that 70% and 10% of the peak areas remained after 2 min reaction time for fluoxetine and metoprolol, respectively. At longer reaction times both N-chloramines had been completely reduced by sulfite, and the product of the sulfite reduction reaction was the parent pharmaceutical amine. Since typical dechlorination times in wastewater treatment are on the order of seconds, this suggests the chloramines formed from these two basic drugs might evade dechlorination and be released into the environment. The implications of chloramine release are discussed.     

Treatment of oily port wastewater effluents using the ultraviolet/hydrogen peroxide photodecomposition system.

This paper presents the nonselective degradation of mechanically pretreated oily wastewater by hydrogen peroxide (H2O2) in the presence and absence of UV irradiation. The effect of chemical oxidation on wastewater biodegradability was also examined. The exclusive use of H2O2 photolyzed by daylight results in quite efficient degradation rates for the low peroxide concentrations used. Higher hydrogen peroxide concentrations inhibit degradation of organic contaminants in the wastewater. The degradation rates of all contaminants are relatively high with an advanced oxidation system (UV/H2O2), but degradation efficiencies are not distinguishably different when 20 or 45 minutes of UV irradiation is used. The excess of H2O2 used in the process can inhibit phenolic degradation and may lead to the formation of a new phenolic fraction. The biodegradability of port wastewater did not increase significantly following the application of the advanced oxidation process.