Paper fibers as a carbon source for the de novo formation of polychlorinated dioxins and furans

The formation of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/Fs) from carbon that was produced by the pyrolysis of paper fibers and from wood charcoal was investigated experimentally. Fibers obtained from filter paper were pyrolyzed at 300° and 800°C to produce low- and high-temperature carbon samples. The two types of carbon and wood charcoal were mixed with silica (SiO₂) and trace copper oxide to produce three synthetic fly ash samples. Experiments to measure the formation of PCCDs/Fs from the three ash samples were conducted using a bench-scale reactor. The two carbon samples derived from paper fibers generated more PCDDs/Fs than was generated by the wood charcoal. The PCDDs/Fs generated by the low-temperature carbon and by the wood charcoal were dominated by the lower-chlorinated PCDFs. Such unique homologue distribution patterns are very similar to those generated by the open burning of household waste. The high-temperature carbon generated more highly chlorinated PCDDs/Fs. The effect of pyrolysis temperature on the de novo formation of PCDDs/Fs from residual carbon is discussed. Paper and paper products contained in household waste are likely to be the source of unburned carbon that contributes to high PCDD/F emissions in the open burning of household waste.     

Optimization of combustion conditions to minimize dioxin emissions

Polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) may enter an incinerator with the waste, be created in poor combustion or form in post-combustion zones under certain conditions of temperature and oxygen. Tests of MSW burning plants show a wide range of emissions of PCDD and PCDF. Diagnostic tests show the relationship between combustion conditions and the emission of PCDD/DF before and after emission controls. Mixing effectiveness, tightness of control, moisture, furnace and post-furnace temperatures, and the use of lime and reduced temperatures for acid-gas control all have an effect on emissions of trace organics. Carbon monoxide (CO), oxygen, moisture and furnace temperature have been found to be closely related to PCDD/PCDF emissions. By control of temperature and/or oxygen, and the use of CO as an indicator, it is possible to find and maintain optimum combustion conditions so as to minimize dioxins and furans. Plants having acid-gas controls reduce emissions below those achieved by good combustion alone.     

Persistent organic pollutant emissions from medical waste incinerators in China

The huge amount of medical waste (MW) has caused a tough challenge to environmental protection in China because of its serious infectious potential. At present, incineration is the most common technology for MW disposal. Unfortunately, the medical waste incinerator (MWI) is considered one of the major sources of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). This study was conducted to investigate the generation and the components of MW; the fingerprint of PCDD/Fs in MWI; and PCDD/F, polychlorinated biphenyl (PCB) and hexachlorobenzene concentrations in residue ash. The estimated annual production of MW was estimated to be 0.97 million tons in China in 2008; in addition, plastic and rubber accounted for 24.5% of MW contents. PCDD/F emissions from MWI could be divided into two main groups according their fingerprints, and the ratio of PCDFs/PCDDs was mostly over 1.5, with a mean value of 3.43. The toxic equivalent of PCDD/Fs was over 30 times that of the value of PCBs in the residue ash, and PCDD/F contents in fly ash accounted for approximately 67% of the total output of PCDD/Fs, which was in line with the UNEP default emission factors for MWI (class 3, 63.7%).     

An investigation on pollutant emissions from co-firing of RDF and coal

Pollutant emissions from co-firing of refuse derived fuel (RDF) and coal were investigated in a vortexing fluidized bed combustor (VFBC). RDF-5 was made of common municipal solid waste (MSW). CaCO₃ was injected in the combustor to absorb HCl at 850 °C. The results show that NO_x and HCl emissions increase with RDF-5 co-firing ratio. The NO_x concentration in flue gas at the bottom of the combustor is higher than that at the top. However, the trend of HCl released is reverse compared with NO_x emissions. It was found that the HCl concentration decreases with increasing the molar ratio of Ca/Cl. However, the effect of CaCO₃ addition on HCl retention is not significant when the molar ratio of Ca/Cl is higher than 5. The chlorine content in fly ash increases obviously with the molar ratio of Ca/Cl. PCDD/Fs emissions decrease slightly with an addition of CaCO₃. In this study incomplete combustion is regarded as the main cause for polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) formation.     

Catalytic detoxification of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans in fly ash

An efficient catalytic detoxification method for polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in fly ash produced by municipal waste incinerator has been studied using palladium on carbon (Pd/C) catalyst. As one of the trace components in fly ash, the detoxification of PCDD/Fs is very difficult because of the interferences of other persistent components with higher concentrations. However, the detoxification reaction of PCDD/Fs shows higher activity in water/isopropanol solution using commercial Pd/C catalyst at 40 degrees C under normal pressure. The results indicated that the catalytic degradation of PCDFs has been found to be easier than that of PCDDs. Moreover, the dechlorination ratios were higher for octa- and hepta-chlorinated congeners than those for tetra- and penta-chlorinated ones. The detoxification process worked well in water. The dechlorination efficiencies of almost all of the PCDD/Fs congeners can reach over 99% within a shorter reaction time.     

Environmental Technology Verification (ETV) test of dioxin emission monitors

The performance of four dioxin emission monitors, including two long-term sampling devices, the Dioxin-MonitoringSystem (DMS) and AMESA (the adsorption method for sampling dioxins and furans), and two semireal-time continuous monitors, the resonance ionization with multimirror photon accumulation time-of-flight mass spectrometer (RIMMPA-TOFMS) and the jet resonance-enhanced multiphoton ionization (jet-REMPI) system were tested. A package boiler burning a simulated chlorinated hazardous waste was used for a total of nine tests. Reference samples were collected during each test and analyzed for polychlorinated dibenzodioxins and dibenzofurans (PCDDs/Fs) using gas chromatography mass spectrometry. The PCDD/F concentrations of the reference samples measured by EPA Method 23 ranged from 0.9 to 6.0 ng toxic equivalence (TEQ)/dry standard cubic meter. The relative accuracies achieved by DMS, AMESA, and jet-REMPI varied from 22.6% to 78.2%, with 100% data completeness. The RIMMPA-TOFMS produced no quantifiable results due to various difficulties associated with the instrument during the testing. The two long-term samplers were easy to install and operate and provided a cumulative, averaged emission for the sampling period. The operations of the two semi-real-time continuous monitors were relatively complex, but one of them provided on-site, real-time data for PCDD/F emissions from measurement of a TEQ correlative indicator compound. This article summarizes results from the individual Environmental Technology Verification reports for the four dioxin monitors. This work was presented, in part, at the Fourth International Conference on Combustion, Incineration/Pyrolysis and Emission Control (i-CIPEC)     

Sludge as dioxins suppressant in hospital waste incineration

Nitrogen containing compounds such as ammonia, urea and amines can effectively inhibit the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Sewage sludge accumulates both sulfur and nitrogen during wastewater treatment so it could be used to reduce PCDD/Fs formation. Indeed, it is observed in this study that the gas evolving from the sludge drying process can significantly suppress chlorobenzene (CBz) and PCDD/Fs formation from fly ash collected from a hospital waste incinerator. For instance, the reduction of hexachlorobenzene (HxCBz) and PCDD/Fs amount was 92.1% and 78.7%, respectively, when the drying gas evolving from 2g sludge flew through 2g fly ash. These tests were conducted in the frame of projects devoted to hospital waste incineration. The disposal technology for hospital waste (HW), developed in this institute, features rotary kiln pyrolysis combined with post-combustion followed by flue gas cleaning. Hence, some preliminary tests were devoted to investigate dioxins suppression by co-pyrolysis and co-combustion of polyvinyl chloride (PVC) and sludge in lab scale. More experimental research will be conducted to appropriately assess these effects of sludge on PCDD/Fs emissions during co-pyrolysis/combustion of HW and sludge.     

Behavior of PCDD/Fs during open burning of municipal solid waste in open dumping sites

Open dumping sites in Surabaya and Palembang, Indonesia, have been studied to investigate emissions of polychlorinated dibenzo-para-dioxins and dibenzofurans (PCDD/Fs) and dioxin-like polychlorinated biphenyls (DL-PCBs), as well as the resulting soil contamination that might be caused by open burning of municipal solid waste. The emission factors of the waste residue, accounting for the ratio of waste burned, have also been characterized. The concentrations of PCDD/Fs and DL-PCBs in soil from Palembang were 61–310 pg-TEQ/g (dry weight) and 6.3–32 pg-TEQ/g, respectively. In Surabaya, very low levels of PCDD/Fs and DL-PCBs, ranging from 0.075 to 0.098 and 0.00032 to 0.095 pg-TEQ/g, respectively, were observed in soil for an open dumping site that included a top cover layer of soil above the compacted waste. The large difference in concentrations can be explained by the fact that open burning of waste is the source of PCDD/Fs and DL-PCBs. The emission factors for the residue for PCDD/Fs ranged from 27 to 140 pg-TEQ/g, and a sensitivity analysis found that the maximum emission factor to the residue could be 5600 pg-TEQ/g. Our results indicate that emissions of PCDD/Fs can be controlled by modifying the open dumping process to one that involves depositing soil layers on top of the compacted waste.     

Hydrodechlorination/detoxification of PCDDs,PCDFs, and co-PCBs in fly ash by using calcium polysulfide

Dioxins like polychlorinated dibenzo-p-dioxins (PCSDDs), polychlorinated dibenzofurans (PCDFs) and polychlorinated biphenyls (PCBs) are mainly emitted from waste incinerators (WIs) and have become an international research focus because of its serious concerns over the adverse health effects. The detoxification of PCCDs/Fs and PCBs is very difficult because of their stable chemical structure. A significant hydrodechlorination/detoxification of polychlorinated 1-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and polychlorinated biphenyls (PCBs) were achieved in fly ash by using an aqueous mixture of calcium hydroxide and sulfur. Two different fly ashes were studied: originating from municipal waste incinerator (FA1) and industrial waste incinerator (FA2). They were heated with the aqueous mixture at 150 °C for 30 or 60 min with agitation. Higher decomposition (87%) and detoxification (87.7%) of PCDD/Fs and PCBs were achieved at 150 °C with two runs; every run was for 30 min, compared to one run for 60 min. FA2 gave higher decomposition and detoxification as compared to FA1, which might be due to higher metal content that played a catalytic role to decompose and detoxify the PCDDs, PCDFs and PCBs. The decomposition and detoxification of PCDFs in fly ash was higher than PCDDs and was augmented with increasing number of chlorides on aromatic compounds. As the highly significant decomposition and detoxification of higher concentration of PCDD/Fs and PCBs were achieved in 1 hour without additive catalyst and at low temperature of 150 °C, therefore, the developed method is cost effective and most suitable to apply on commercial/industrial level. The detail results of hydrodechlorination/detoxification of PCDD, PCDFs at different conditions are described and its mechanism is discussed.     

SETTING DIOXIN EMISSION LIMITS FOR MSW INCINERATORS: A MULTIMEDIA EXPOSURE ASSESSMENT FRAMEWORK

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are emitted in trace amounts from municipal solid waste (MSW) incinerators. The exposure to PCDD/Fs experienced by an individual is dominated by the food chain pathway, which accounts for over 98% of the total uptake. Defining a target daily intake (the World Health Organization TDI of 10 pg I-TEQ kg.bw⁻¹day⁻¹) exposure assessment algorithms were then applied to arrive at the corresponding PCDD/F levels in air, soil, plants, food products, etc., which would allow the target intake to be met while retaining the balance of intake between the various exposure pathways. These concentrations were converted to an ambient air concentration of PCDD/Fs and ultimately, by defining criteria for acceptability, to a guide value for PCDD/F concentration in emissions from the MSW incinerator. This strategy was applied to PCDD/F emissions from MSW incinerators of various sizes against two illustrative criteria for acceptability: an “insignificant” release and a threshold above which the release may require further assessment for environmental effects and for control. Using the criteria developed in this paper, the current PCDD/F emission limit of 0.1 ng I-TEQ m⁻³results in an emission that is classed as “insignificant” for all plant sizes. However, higher emission concentrations can also be accommodated below the threshold for further assessment and control.     

Treatment of Sydney N.S. tar pond sludge in a pilot‐scale rotary kiln

Tar pond wastes from Sydney, Nova Scotia, containing 50 ppm or more of polychlorinated biphenyls (PCBs) were treated in a pilot‐scale rotary kiln. In order to use the existing feed system attached to the rotary kiln, the wastes were first oven‐dried. Stack gas sampling was conducted during the test, which included measurement of volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), semi‐volatile organic compounds (SVOCs), HCl, and metals. The purpose of this study was to determine emissions from treatment of the tar pond waste using rotary kiln technology. It was found that the dried sludge could sustain combustion in the kiln without any supporting fuel. The emissions of polychlorinated dibenzodioxins/furans (PCDD/Fs) were higher than the Canadian Council of Ministers of the Environment (CCME) air emissions guidelines, and the reasons for this are discussed. © 2008 Wiley Periodicals, Inc.     

Correlations between homologue concentrations of PCDD/Fs and toxic equivalency values in laboratory-, package boiler-, and field-scale incinerators

The toxic equivalency (TEQ) values of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) are predicted with a model based on the homologue concentrations measured from a laboratory-scale reactor (124 data points), a package boiler (61 data points), and operating municipal waste incinerators (114 data points). Regardless of the three scales and types of equipment, the different temperature profiles, sampling emissions and/or solids (fly ash), and the various chemical and physical properties of the fuels, all the PCDF plots showed highly linear correlations (R(2)>0.99). The fitting lines of the reactor and the boiler data were almost linear with slope of unity, whereas the slope of the municipal waste incinerator data was 0.86, which is caused by higher predicted values for samples with high measured TEQ. The strong correlation also implies that each of the 10 toxic PCDF congeners has a constant concentration relative to its respective total homologue concentration despite a wide range of facility types and combustion conditions. The PCDD plots showed significant scatter and poor linearity, which implies that the relative concentration of PCDD TEQ congeners is more sensitive to variations in reaction conditions than that of the PCDF congeners.     

Statistical modelling for the prediction and control of PCDDs and PCDFs emissions from municipal solid waste incinerators

The emissions of a full range of polychlorinated dibenzo-p-dioxins and furans (PCDDs/PCDFs) have become one of the most controversial issues in siting and building new municipal incinerators. The lack of comprehensive evaluation of the PCDDs/PCDFs formation and emission control technologies in earlier times resulted in ambiguity in the decision-making of incineration projects. Until the last decade, several emission tests of municipal solid waste incineration regarding to new combustion criteria, public regulations, and risk assessments were conducted and reported in the literature. However, only a few analyses of statistical prediction and control have been established. This paper presents a series of multiple linear regression models for PCDDs/PCDFs emission prediction and control corresponding to different types of incinerators. The data used in the regression analysis were integrated from several testing programmes held in North America. By applying these regression results, evaluation of various combustion criteria, public regulations, and environmental and health risk assessment can then be achieved. Such evaluation is valuable for some developing countries which do not have sufficient finance or engineering experience to pursue large scale emission tests, but need rapid promulgation of emissions control for municipal solid waste incinerators.     

Repartition of PCDD and PCDF in the emissions of municipal solid waste incinerators between the particulate and volatile phases

The present paper refers to the results of a research project on the polychlorinated dibenzyil-p-dioxin (PCDD) and polychlorinated dibenzofurans repartition in particulate and volatile phase in emissions from municipal solid waste incinerators. The distribution of such micropollutants between the different phases is analyzed in terms of absolute weights and in terms of 2, 3, 7, 8 TCDD Equivalents. This paper shows that more than half of the total content of PCDD/Fs emitted are adsorbed in the fly ash, with the remaining part in the volatile phase. Such repartition is inverted if the PCDD/Fs are expressed in terms of 2, 3, 7, 8 TCDD Equivalent.     

Decreased PCDD/F formation when co-firing a waste fuel and biomass in a CFB boiler by addition of sulphates or municipal sewage sludge

Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are formed during waste incineration and in waste-to-energy boilers. Incomplete combustion, too short residence times at low combustion temperatures (<700 °C), incineration of electronic waste and plastic waste containing chlorine are all factors influencing the formation of PCDD/Fs in boilers. The impact of chlorine and catalysing metals (such as copper and iron) in the fuel on PCDD/F formation was studied in a 12 MW_th circulating fluidised bed (CFB) boiler. The PCDD/F concentrations in the raw gas after the convection pass of the boiler and in the fly ashes were compared. The fuel types were a so-called clean biomass with low content of chlorine, biomass with enhanced content of chlorine from supply of PVC, and solid recovered fuel (SRF) which is a waste fuel containing higher concentrations of both chlorine, and catalysing metals. The PCDD/F formation increased for the biomass with enhanced chlorine content and it was significantly reduced in the raw gas as well as in the fly ashes by injection of ammonium sulphate. A link, the alkali chloride track, is demonstrated between the level of alkali chlorides in the gas phase, the chlorine content in the deposits in the convection pass and finally the PCDD/F formation. The formation of PCDD/Fs was also significantly reduced during co-combustion of SRF with municipal sewage sludge (MSS) compared to when SRF was fired without MSS as additional fuel.     

Formation of persistent chlorinated aromatic compounds in simulated and real fly ash from iron ore sintering

Effects of carbon concentration and Cu additive in simulated fly ash (SFA) and real fly ash (RFA) on the formation of polychlorinated dibenzofurans (PCDFs), polychlorinated dibenzo-p-dioxins (PCDDs), chlorobenzenes, and polychlorinated biphenyls which were all regarded as persistent chlorinated aromatics in iron ore sintering were investigated. In the annealing process of SFA with various carbon contents, the yield of chlorinated aromatics and the I-TEQ obtained their maximum at 10 wt% carbon content. Active carbon in SFA acted as the carbon source as well as an adsorbent which led to higher production of PCDD/F in solid phase at 10 wt% carbon content. The increase of carbon content will be beneficial on the formation of 2,3,7,8-Chloro-substituted PCDF compared with 2,3,7,8-Chloro-substituted PCDD. In addition, the CuCl₂·2H₂O was a much more powerful catalyst in the formation of chlorinated aromatic compounds compared with elementary Cu, since it served as both a catalyst and a chlorine donor. However, the RFA behaved similarly with SFA with elementary Cu in the formation of chlorinated aromatic compounds. The effect of carbon content and copper additives on formation of 2,3,7,8-chloro-substituted congeners displayed similar characteristics with the tetra- to octa-PCDD/F isomers and even the total PCDD/Fs.     

Characterizing emissions from open burning of military food waste and ration packaging compositions

Emissions from open burning of military food waste and ration packaging compositions were characterized in response to health concerns from open burning disposal of waste, such as at military forward operating bases. Emissions from current and prototype Meals, Ready-to-Eat (MREs), and material options for their associated fiberboard packaging were quantified to assess contributions of the individual components. MREs account for 67–100% of the particulate matter (PM), volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), and polychlorinated dibenzo-p-dioxins and -furans (PCDDs/PCDFs) emissions when burned in unison with the current fiberboard container and liner. The majority of the particles emitted from these burns are of median diameter 2.5 µm (PM_2.5). Metal emission factors were similar regardless of waste composition. Measurements of VOCs and PAHs indicate that targeted replacement of MRE components may be more effective in reducing emissions than variation of fiberboard-packaging types. Despite MRE composition variation, equivalent emission factors for PM, PAH, VOC, and PCDD/PCDF were seen. Similarly, for fiberboard packaging, composition variations exhibited essentially equivalent PM, PAH, VOC, and PCDD/PCDF emission factors amongst themselves. This study demonstrated a composition-specific analysis of waste burn emissions, assessing the impact of waste component substitution using military rations.     

Influences of chlorine content on emission of HCl and organic compounds in waste incineration using fluidized beds

HCl and some organic compounds are the precursors of polychlorinated dibenzo-p-dioxins and furans (PCDD/Fs) in municipal solid waste incinerators. In this work, a lab-scale fluidized bed incinerator is adopted to study the relationship between the organic and the inorganic chlorine contents of artificial wastes and the emissions of HCl and organic compounds. The lower threshold limit (LTL) of chlorine content below which HCl and organic compounds are not generated is studied. Experimental results showed that organic chlorides had a greater potential to release chlorine than inorganic chlorides. The generation of organic pollutants fell, but the emissions of HCl increased with the temperature. The concentrations of chlorophenols (CPs)/chlorobenzenes (CBs) increased with chlorine contents. No LTL existed for HCl regardless of whether CaO was added. The LTL for CPs was between 0.1 and 0.3wt% of inorganic chloride, but there was none for organic sources. For CBs, the LTL was between 0.5 and 1.0wt% for inorganics at 700 and 800 degrees C, but 0.1-0.3 wt% at 700 degrees C and 0.3-0.5 wt% at 800 degrees C for organics. The production of PAHs and benzene, toluene, ethylbenzene and xylene (BTEX) was related to the surplus hydrogen ions that were not reacted with the chlorine. Adding CaO inhibited the production of HCl, CBs and CPs, but did not seriously affect PAHs and BTEX.     

Generation and distribution of PAHs in the process of medical waste incineration

After the deadly earthquake on May 12, 2008 in Wenchuan county of China, several different incineration approaches were used for medical waste disposal. This paper investigates the generation properties of polycyclic aromatic hydrocarbons (PAHs) during the incineration. Samples were collected from the bottom ash in an open burning slash site, surface soil at the open burning site, bottom ash from a simple incinerator, bottom ash generated from the municipal solid waste (MSW) incinerator used for medical waste disposal, and bottom ash and fly ash from an incinerator exclusively used for medical waste. The species of PAHs were analyzed, and the toxicity equivalency quantities (TEQs) of samples calculated. Analysis results indicate that the content of total PAHs in fly ash was 1.8 × 10³ times higher than that in bottom ash, and that the strongly carcinogenic PAHs with four or more rings accumulated sensitively in fly ash. The test results of samples gathered from open burning site demonstrate that Acenaphthylene (ACY), Acenaphthene (ACE), Fluorene (FLU), Phenanthrene (PHE), Anthracene (ANT) and other PAHs were inclined to migrate into surrounding environment along air and surface watershed corridors, while 4- to 6-ring PAHs accumulated more likely in soil. Being consistent with other studies, it has also been confirmed that increases in both free oxygen molecules and combustion temperatures could promote the decomposition of polycyclic PAHs. In addition, without the influence of combustion conditions, there is a positive correlation between total PCDD/Fs and total PAHs, although no such relationship has been found for TEQ.     

Characterization of PCDD/Fs and heavy metals from MSW incineration plant in Harbin

The characterization of PCDD/Fs and heavy metals in the flue gas and fly ash of Harbin municipal solid waste (MSW) incineration plant, located in the northeast of China, was investigated in this study. The MSW was treated in a twin internal fluidized (TIF) bed incinerator. The results indicate that the emission of PCDD/Fs into the environment is 0.02 ng I-TEQ/m3 and the level of PCDD/Fs in the fabric filter fly ash is 0.7982 ng I-TEQ/g. The leachability levels of Pb, Cd and Hg in the fly ash are below the limits of environmental protection standard in China. However, the contents of Cu, Zn, and Hg are high in the fly ash. This suggests that the fly ash is a hazardous waste that requires special treatment and disposal. The practice of more than four years of operation shows that the TIF bed incinerator is very suitable and practical for China.