Monitoring operational and leachate characteristics of an aerobic simulated landfill bioreactor

Long-term biodegradation of MSW in an aerobic landfill bioreactor was monitored as a function of time during 510 days of operation. Operational characteristics such as air importation, temperature and leachate recirculation were monitored. The oxygen utilization rates and biodegradation of organic matter rates showed that aerobic biodegradation was feasible and appropriate to proceed in aerobic landfill bioreactor. Leachate analyses showed that the aerobic bioreactor could remove above 90% of chemical oxygen demand (COD) and close to 100% of biochemical oxygen demand (BOD5) from leachate. Ammonium (NH4+), nitrate (NO3-) and sulphate (SO4(2-)) concentrations of leachate samples were regularly measured. Results suggest that nitrification and denitrification occurred simultaneously, and the increase in nitrate did not reach the levels predicted stoichiometrically, suggesting that other processes were occurring. Leachate recirculation reduced the concentrations of heavy metals because of the effect of the high pH of the leachate, causing heavy metals to be retained by processes such as sorption on MSW, carbonate precipitation, and hydroxide precipitation. Furthermore, the compost derived from the aerobic biodegradation of the organic matter of MSW may be considered as soil improvement in the agricultural plant production. Bio-essays indicated that the ecotoxicity of leachate from the aerobic bioreactor was not toxic at the end of the experiment. Finally, after 510 days of degradation, waste settlement reached 26% mainly due to the compost of the organic matter.     

Degradation of Phenolic Resin by Tremetes versicolor

A phenolic resin that is used as syntan in leather manufacturing was degraded using Tremetes versicolor. On degradation of this resin for eight days, the reduction in biochemical oxygen demand (BOD), chemical oxygen demand (COD) and total organic carbon (TOC) were 65.11, 76.66 and 72.94% respectively. It was found from the infra red (IR) spectra of the samples that up to seven days the aromaticity was not perturbed however there were reductions in BOD and COD. Addition of co-substrate starch, brought about reduction in BOD, COD and TOC by 85.36, 91.93 and 89.98% respectively. After eight days, there observed a disturbance in the aromatic ring. The enzyme was extracted and assayed for polyphenol oxidase and laccase. Polyphenol oxidase activity and laccase activity of the crude enzyme were found to be 31.4 and 1.67 U/mL. On ammonium sulfate precipitation and dialysis, the polyphenol oxidase activity and laccase activity were enhanced by 1.5- and 3.2-folds respectively.     

Report: anaerobic digestion of a sulphate-rich high-strength landfill leachate: the effect of differential dosing with FeCl3.

The effect of different dose concentrations of FeCl3 on the performance of a mesophilic anaerobic digester treating a highly alkaline, high-strength and sulphate-rich landfill leachate was tested. The results indicated that sulphate reduction was the predominant reaction and methanogenic processes were entirely inhibited in the reactor without FeCl3 addition. Adding FeCl3 into the reactor restored some methanogenic activity and also improved the rates of sulphate reduction. A combination of sulphate reduction and methanogenic activity resulted in up to 75% chemical oxygen demand (COD) removal and 85% sulphate removal. Sulphate reduction remained the principle mechanism by which COD removal took place with a methane yield of only between 0.14 and 0.18 m3 CH4 kg(-1) COD removed being achieved. The process was, however, stable and offered advantages for the further treatment or conveyance of the anaerobically treated leachate.     

Use of Sphagnum peat moss and crushed mollusk shells in fixed-bed columns for the treatment of synthetic landfill leachate

A laboratory bench-scale fixed-bed column study operated as a down-flow configuration was conducted to evaluate Sphagnum peat moss and crushed mollusk shells as natural low-cost adsorbents for the removal of heavy metals from aerated and unaerated synthetic landfill leachate. Columns were packed with 15 cm of prepared peat moss, or 15 cm adsorbent mixtures made up of peat moss and crushed mollusk shells (4.0–4.75 mm) from Lake Ontario at different bed depth ratios. Peat was found to have the best adsorption capacities in columns treating aerated synthetic leachate for cadmium and nickel with 78.6% and 83.8% removal efficiencies, respectively. The removal of chemical oxygen demand (COD) and total nitrogen from the synthetic leachate was also monitored to evaluate the potential effects of biological activity on heavy metal adsorption. Columns receiving unaerated raw synthetic leachates did not show any significant removal of COD and total nitrogen, whereas some reduction in COD and total nitrogen was noted in the columns treating aerated synthetic landfill leachate. The results suggested that biological activity and biofilm growth could positively contribute to heavy metal retention within the fixed-media biosorption columns.     

有机磷农药废水处理技术

久效磷和亚磷酸三甲酯生产过程中产生的废水经碱解沉淀和超声气浮预处理,可降低其ＣＯＤ和毒性,提高其可生化性,再经以光合细菌为主的生化处理,可使其ＣＯＤ降至２００ｍｇ／Ｌ。     

Seasonal dynamics in leachate hydrochemistry and natural attenuation in surface run-off water from a tropical landfill

Open waste dump systems are still widely used in Indonesia. The Jatibarang landfill receives 650-700 tons of municipal waste per day from the city of Semarang, Central Java. Some of the leachate from the landfill flows via several natural and collection ponds to a nearby river. The objectives of the study were to identify seasonal landfill leachate characteristics in this surface water and to determine the occurrence of natural attenuation, in particular the potential for biodegradation, along the flow path. Monthly measurements of general landfill leachate parameters, organic matter-related factors and redox-related components revealed that leachate composition was influenced by seasonal precipitation. In the dry season, electrical conductivity and concentrations of BOD, COD, N-organic matter, ammonia, sulphate and calcium were significantly higher (1.1-2.3 fold) than during the wet season. Dilution was the major natural attenuation process acting on leachate. Heavy metals had the highest impact on river water quality. Between the landfill and the river, a fivefold dilution occurred during the dry season due to active springwater infiltration, while rainwater led to a twofold dilution in the wet season. Residence time of leachate in the surface leachate collection system was less than 70 days. Field measurements and laboratory experiments showed that during this period hardly any biodegradation of organic matter and ammonia occurred (less than 25%). However, the potential for biodegradation of organic matter and ammonia was clearly revealed during 700 days of incubation of leachate in the laboratory (over 65%). If the residence time of leachate discharge can be increased to allow for biodegradation processes and precipitation reactions, the polluting effects of leachate on the river can be diminished.     

Treatment of a high-strength sulphate-rich alkaline leachate using an anaerobic filter

The research looks at the feasibility of treating an alkaline sulphate-rich leachate arising from the co-disposal of municipal solid waste with cement kiln dust by means of an anaerobic filter (AF). This type of leachate with a high sulphate concentration is commonly prohibited for discharge to sewer and requires an on-site treatment solution. The AF used had a working volume of 4l and contained reticulated polyurethane foam as the biomass support material. The filters were operated over a 152 day experimental period during which the COD loading onto the filter was increased from 0.76 to 7.63kgCODm(-3)d(-1). In the early stages of operation at low loading, soluble sulphides accumulated that inhibited methanogenic activity. This was restored by dosing FeCl(3) to the reactor. The continued dosing allowed efficient COD removal of between 75% and 90% until the nominal retention time in the reactor was 3 days, at which point reactor performance declined significantly. The main mechanism for COD removal was by sulphate-reducing bacteria, which also resulted in up to 88% sulphate removal from the leachate. The average methane generation rate was 0.10lg(-1) COD removed. The results indicate the potential for using this approach as a pre-treatment that could significantly reduce the COD load to a second stage treatment process, but problems associated with the implementation of the technology at a larger scale have been identified.     

Microbial influenced degradation of solidified waste binder

Ordinary cement pastes with water/cement (w/c) ratios of 0.2, 0.4 and 0.5 were used to examine the chemical and physical effects of microbial influenced degradation (MID). Samples were exposed to an active culture of Thiobacillus thiooxidans or to sterile media containing sulphuric acid using an intermittent immersion technique. Acid consumption and Ca, Al and Fe releases are presented for an exposure period of 90 days. Exposed samples were also sectioned and analysed by scanning electron microscopy (SEM) and energy dispersive X-ray (EDX). All cement paste samples were subject to significant degradation in either sterile acid media or the T. thiooxidans lixiviant. Corrosion depths observed from SEM examination of exposed samples were affected by the w/c ratio of the cement. The extent and rate of degradation were not apparent from the calculated rate of hydrogen ion consumption, or the leaching rates of Ca, Al and Fe. It was not possible to distinguish differences in corrosion due to the chemical and microbial influenced degradation from the results obtained to date and further work is focusing on modified procedures to address this.     

Remediation of acid mine drainage leachate by a physicochemical and biological treatment‐train approach

Biological and physicochemical approaches were utilized in a treatment train for acid mine dis charge (AMD) waters. Anaerobic bioreactors, chemical precipitation reactors, and biopolymer chelation reactors, operated in static, semicontinuous, and continuous flow modes, removed significant quantities of metals and sulfates associated with AMD water. Static tests indicated accept able copper removal via precipitation by generation of hydrogen sulfide in anaerobic reactors. However, low pH affected the biopolymer coating in the chelation reactor, resulting in loss of bed surface. Corrections of AMD to pH > 7 resulted in some metal precipitationprior to biopolymer treatment. A series of static semicontinuous tests at pH 5.0 provided improved metal and sulfate removal. Copper (Cu⁺) was reduced to trace concentrations, while manganese (Mn⁺), although reduced, proved to be the most recalcitrant of the metals. © 2006 Wiley Periodicals, Inc.     

Field‐scale uranium (VI) bioimmobilization monitored by lipid biomarkers and 13C‐acetate incorporation

At the Old Rifle uranium mill‐tailing site in eastern Colorado, a test of subsurface amendment with acetate to stimulate the reductive immobilization of uranium was monitored by using lipid biomarker analysis and incorporation of ¹³C‐labeled acetate into lipid biomarkers. Both sediment and groundwater samples were analyzed. Within 7 days of acetate addition, groundwater microbial biomass increased by a factor of 5, and remained higher than control values in most samples for the 28 days sampled. At 29 days after the beginning of acetate amendment, 4 of 12 sediment samples had microbial biomass greater than the 95 percent confidence interval of controls. The mole percents of the phospholipid fatty acids 16:1ω7c and 16:1ω5c increased over control values upon acetate amendment, and incorporated high levels of ¹³C from labeled acetate in groundwater and sediment samples. 16:1ω7c is a biomarker for Geobacter, and evidence is provided that 16:1ω5c represents an unidentified iron‐reducing bacterium, probably a member of the Desulfobulbaceae. Biomarkers for organisms other than iron‐reducing bacteria, iso‐ and anteiso‐branched fatty acids and 18:1ω9c, decreased upon acetate amendment, and had their highest stable isotope incorporation at least 4 days after labeled acetate amendment ended, evidence for carbon‐sharing between iron‐reducers and other microorganisms. © 2011 Wiley Periodicals, Inc.     

Anaerobic treatment of effluents from an industrial polymers synthesis plant

The feasibility of the anaerobic treatment of an industrial polymer synthesis plant effluent was evaluated. The composition of the wastewater includes acrylates, styrene, detergents, a minor amount of silicates and a significant amount of ferric chloride. The average chemical oxygen demand (COD) corresponding is about 2000 mg/l. The anaerobic biodegradability of the effluent is shown and the toxicity effect on the populations of anaerobic bacteria is evaluated. The results of the anaerobic biodegradation assays show that 62% of the wastewater compounds, measured as COD, could be consumed. An upflow anaerobic sludge blanket (UASB) reactor was used in the evaluation, it has a diameter–height ratio of 1:7, and 4-liter volume. The inoculum was obtained from a UASB pilot plant that treats brewery wastewaters. At the beginning of the operation, the biomass showed an anaerobic activity of 0.58 gCOD/(gVSS×d), it decreased only 2.5% in the subsequent 4 months. After 35 days of continuous operation, the reactor was operated at different steady states for 140 days. The COD was maintained at 2200 mg/l in the feed. The results were: organic loading rate (OLR): 4.3 kg COD/(m³×d), hydraulic retention time: 12 h, superficial velocity: 1 m/h, average biogas productivity: 290 L CH₄/kg COD fed, biogas composition: 70–75% methane and a COD removal percentage >75%. ©     

Chemical Oxidation Performance in High Temperature,Saline Groundwater Impacted With Hydrocarbons

A series of laboratory microcosm experiments and a field pilot test were performed to evaluate the potential for in situ chemical oxidation (ISCO) of aromatic hydrocarbons and methyl tertiary butyl ether (MTBE), a common oxygenate additive in gasoline, in saline, high temperature (more than 30 °C) groundwater. Groundwater samples from a site in Saudi Arabia were amended in the laboratory portion of the study with the chemical oxidants, sodium persulfate (Na₂S₂O₈) and sodium percarbonate (Na₂(CO₃)₂), to evaluate the changes in select hydrocarbon and MTBE concentrations with time. Almost complete degradation of the aromatic hydrocarbons, naphthalene and trimethylbenzenes (TMBs), was found in the groundwater sample amended with persulfate, whereas the percarbonate‐amended sample showed little to no degradation of the target hydrocarbon compounds in the laboratory. Isotopic analyses of the persulfate‐amended samples suggested that C‐isotope fractionation for xylenes occurred after approximately 30 percent reduction in concentration with a decline of about 1 percent in the δ¹³C values of xylenes. Based on the laboratory results, pilot‐scale testing at the Saudi Arabian field site was carried out to evaluate the effectiveness of chemical oxidation using nonactivated persulfate on a high temperature, saline petroleum hydrocarbon plume. Approximately 1,750 kg of Na₂S₂O₈ was delivered to the subsurface using a series of injection wells over three injection events. Results obtained from the pilot test indicated that all the target compounds decreased with removal percentages varying between 86 percent for naphthalene and more than 99 percent for the MTBE and TMBs. The benzene, toluene, ethylbenzene, and xylene compounds decreased to 98 percent on average. Examination of the microbial population upgradient and downgradient of the ISCO reactive zone suggested that a bacteria population was present following the ISCO injections with sulfate‐reducing bacteria (SRB) being the dominant bacteria present. Measurements of inorganic parameters during injection and postinjection indicated that the pH of the groundwater remained neutral following injections, whereas the oxidation–reduction potential remained anaerobic throughout the injection zone with time. Nitrate concentrations decreased within the injection zone, suggesting that the nitrate may have been consumed by denitrification reactions, whereas sulfate concentrations increased as expected within the reactive zone, suggesting that the persulfate produced sulfate. Overall, the injection of the oxidant persulfate was shown to be an effective approach to treat dissolved aromatic and associated hydrocarbons within the groundwater. In addition, the generation of sulfate as a byproduct was an added benefit, as the sulfate could be utilized by SRBs present within the subsurface to further biodegrade any remaining hydrocarbons. ©2015 Wiley Periodicals, Inc.     

Biohydrogen using leachate from an industrial waste landfill as inoculum

Since hydrogen is a renewable energy source, biohydrogen has been researched in recent years. However, data on hydrogen fermentation by a leachate from a waste landfill as inoculum are scarce. We investigated hydrogen production using a leachate from an industrial waste landfill in Kanagawa Prefecture. The results showed no methane gas production, and the leachate was a suitable inoculum for hydrogen fermentation. The maximum H₂ yield was 2.67 mol of H₂ per mol of carbohydrate added, obtained at 30°C and an initial pH of 7. The acetate and butyrate production was significant when the H₂ yield was higher. Oxidation–reduction potential analysis of the culture suggested that hydrogen-producing bacteria in the leachate were facultative anaerobic. Scanning electron microscope observations revealed that the hydrogen-producing bacteria comprised bacilli about 2 μm in length.     

Enhanced hydrolysis and methane yield by applying microaeration pretreatment to the anaerobic co-digestion of brown water and food waste

Microaeration has been used conventionally for the desulphurization of biogas, and recently it was shown to be an alternative pretreatment to enhance hydrolysis of the anaerobic digestion (AD) process. Previous studies on microaeration pretreatment were limited to the study of substrates with complex organic matter, while little has been reported on its effect on substrates with higher biodegradability such as brown water and food waste. Due to the lack of consistent microaeration intensities, previous studies were not comparable and thus inconclusive in proving the effectiveness of microaeration to the overall AD process. In this study, the role of microaeration pretreatment in the anaerobic co-digestion of brown water and food waste was evaluated in batch-tests. After a 4-day pretreatment with 37.5 mL-O₂/L_R-d added to the liquid phase of the reactor, the methane production of substrates were monitored in anaerobic conditions over the next 40 days. The added oxygen was consumed fully by facultative microorganisms and a reducing environment for organic matter degradation was maintained. Other than higher COD solubilization, microaeration pretreatment led to greater VFA accumulation and the conversion of other short chain fatty acids to acetate. This could be due to enhanced activities of hydrolytic and acidogenic bacteria and the degradation of slowly biodegradable compounds under microaerobic conditions. This study also found that the nature of inoculum influenced the effects of microaeration as a 21% and 10% increase in methane yield was observed when pretreatment was applied to inoculated substrates, and substrates without inoculum, respectively.     

Satellite and Ground Based Monitoring of Aerosol Plumes

Plumes of atmospheric aerosol have been studied using a rangeof satellite and ground-based techniques. The Sea-viewing WideField-of-view Sensor (SeaWiFS) has been used to observe plumesof sulphate aerosol and Saharan dust around the coast of theUnited Kingdom. Aerosol Optical Thickness (AOT) was retrievedfrom SeaWiFS for two events; a plume of Saharan dusttransported over the United Kingdom from Western Africa and aperiod of elevated sulphate experienced over the Easternregion of the UK. Patterns of AOT are discussed and related tothe synoptic and mesoscale weather conditions. Furtherobservation of the sulphate aerosol event was undertaken usingthe Advanced Very High Resolution Radiometer instrument(AVHRR). Atmospheric back trajectories and weather conditionswere studied in order to identify the meteorologicalconditions which led to this event. Co-located ground-basedmeasurements of PM₁₀ and PM_2.5 were obtained for 4sites within the UK and PM_2.5/10 ratios were calculatedin order to identify any unusually high or low ratios(indicating the dominant size fraction within the plume)during either of these events. Calculated percentiles ofPM_2.5/10 ratios during the 2 events examined show thatthese events were notable within the record, but were in noway unique or unusual in the context of a 3 yr monitoringrecord. Visibility measurements for both episodes have beenexamined and show that visibility degradation occurred duringboth the sulphate aerosol and Saharan dust episodes.     

Recovery of metal values from zinc solder dross

Zinc solder dross containing 14.8% Sn, 16.3% Pb, 0.41% Al and 64.5% Zn was leached with 3% H₂SO₄ at 45°C for 1 h. Zinc and aluminum went into solution, whereas lead and tin remained with the residue. Aluminum was selectively precipitated as calcium aluminum carbonate by treating the sulphate leachate with limestone at pH 4.8. Zinc sulphate solution was either evaporated to obtain zinc sulphate crystals or precipitated as basic zinc carbonate at pH 6.8. The undissolved lead and tin were leached with 5 M hot hydrochloric acid. The major part of lead chloride ( 73%) was separated by cooling the leached products down to room temperature. From the soluble fraction, tin was recovered as hydrated tin oxide by alkylation with caustic soda at pH 2.4, while the remaining lead was separated at pH 8.5 as lead hydroxide. A process flowsheet had been suggested which involved two-stage hydrometallurgical treatment. Parameters affecting the recovery efficiency of the suggested method such as temperature, time, pH and acid: solid stoichiometric ratio were investigated. Results obtained revealed that the optimum leaching conditions were achieved by using 20 ml of 3% H₂SO₄ acid/g dross for 1 h at 45°C. Recovery efficiency of the metal salts was 99.1, 99.4, 99.6 and 99.5% for Zn, Al, Pb and Sn respectively. Recovery efficiency was related to the solubility of the concerned salts under the given experimental conditions.     

Conversion of calcium sulphide to calcium carbonate during the process of recovery of elemental sulphur from gypsum waste

The production of elemental sulphur and calcium carbonate (CaCO₃) from gypsum waste can be achieved by thermally reducing the waste into calcium sulphide (CaS), which is then subjected to a direct aqueous carbonation step for the generation of hydrogen sulphide (H₂S) and CaCO₃. H₂S can subsequently be converted to elemental sulphur via the commercially available chemical catalytic Claus process. This study investigated the carbonation of CaS by examining both the solution chemistry of the process and the properties of the formed carbonated product. CaS was successfully converted into CaCO₃; however, the reaction yielded low-grade carbonate products (i.e. <90 mass% as CaCO₃) which comprised a mixture of two CaCO₃ polymorphs (calcite and vaterite), as well as trace minerals originating from the starting material. These products could replace the Sappi Enstra CaCO₃ (69 mass% CaCO₃), a by-product from the paper industry which is used in many full-scale AMD neutralisation plants but is becoming insufficient. The insight gained is now also being used to develop and optimize an indirect aqueous CaS carbonation process for the production of high-grade CaCO₃ (i.e. >99 mass% as CaCO₃) or precipitated calcium carbonate (PCC).     

Influence of composition on the biomethanation potential of restaurant waste at mesophilic temperatures

A synthetic waste was used to study the effect of waste composition on anaerobic degradation of restaurant waste. It was made by blending melted pork lard, white cabbage, chicken breast, and potato flakes, to simulate lipids, cellulose, protein, and carbohydrates, respectively. Four blends of the four constituents with an excess of each component were assayed and compared with a fifth blend containing an equal amount of chemical oxygen demand (COD) of each of the four components. The methane production and the time course of soluble COD and volatile fatty acids were assessed in batch assays. A high reduction of volatile solids (between 94% and 99.6%) was obtained in all the assays. The methane yield was between 0.40 m(3) CH(4)/kg VS(initial) (excess of carbohydrates) and 0.49 m(3) CH(4)/kg VS(initial) (excess of lipids). The degradation of the lipid-rich assays differed from the others. Fifty percent of the biochemical methane potential was obtained after 3-6 days for all of the assays, except for the one with excess of lipids which achieved 50% methanation only after 14.7 days of incubation. In the assay with excess of lipids, a considerable fraction of COD remained in the liquid phase, suggesting an inhibition of the methanogenic process that was likely due to the accumulation of long chain fatty acids. The hydrolysis rate constants, assuming first order kinetics, over the first 6 days were between 0.12d(-1) (excess of lipids) and 0.32 d(-1) (excess of carbohydrates). The results indicate that anaerobic digestion facilities with large variations in lipid input could have significant changes in process performance that merit further examination.     

Aerobic Biodegradation of Hydrocarbons in High Temperature and Saline Groundwater

A series of laboratory microcosm experiments and a field pilot test were performed to evaluate the potential for aerobic biodegradation of aromatic hydrocarbons and methyl tert‐butyl ether (MtBE; a common oxygenate additive in gasoline) in saline, high temperature (>30° C) groundwater. Aquifer, sediment, and groundwater samples from two sites, one in Canada and another in Saudi Arabia, were incubated for 106 days to evaluate the changes in select hydrocarbon and MtBE concentrations and microbial community structure. Almost complete biodegradation of the aromatic hydrocarbons was found in the Saudi Arabian microcosm samples whereas the Canadian microcosm samples showed no significant biodegradation during the laboratory testing. MtBE degradation was not observed in either set of microcosms. Denaturing gradient gel electrophoresis analyses showed that, while the Canadian microorganisms were the most diverse, they showed little response during incubation. The microbial communities for the Saudi Arabian sample contained significant numbers of microorganisms capable of hydrocarbon degradation which increased during incubation. Based on the laboratory results, pilot‐scale testing at the Saudi Arabian field site was carried out to evaluate the effectiveness of enhanced aerobic biodegradation on a high temperature, saline petroleum hydrocarbon plume. Dissolved oxygen was delivered to the subsurface using a series of oxygen diffusion emitters installed perpendicular to groundwater flow, which created a reactive zone. Results obtained from the seven‐month field trial indicated that all the target compounds decreased with removal percentages varying between 33 percent for the trimethylbenzenes to greater than 80 percent for the BTEX compounds. MtBE decreased 40 percent on average whereas naphthalene was reduced 85 percent on average. Examination of the microbial population upgradient and downgradient of the emitter reactive zone suggested that the bacteria population went from an anaerobic, sulfate‐reducing dominated population to one dominated by a heterotrophic aerobic bacteria dominant population. These studies illustrate that field aerobic biodegradation may exceed expectations derived from simple laboratory microcosm experiments. Also, high salinity and elevated groundwater temperature do not appear to inhibit in situ aerobic biorestoration. © 2014 Wiley Periodicals, Inc.     

Anaerobic biotransformation and methane generation potential of cheese whey in batch and UASB reactors.

Anaerobic treatability and methane generation potential of cheese whey were determined in batch reactors. Furthermore, the effect of nutrient and trace metal supplementation on the batch anaerobic treatment, and the high-rate anaerobic treatability of cheese whey in upflow anaerobic sludge blanket (UASB) reactors were investigated. To this purpose biochemical methane potential experiments were conducted and single- and two-stage UASB reactors with granular cultures were operated. In UASB experiments significance of process staging, operational parameters such as hydraulic retention time (HRT), influent chemical oxygen demand (COD) concentration and loading rate were also investigated. The results revealed that nutrient and trace metal supplementation is vital for the anaerobic treatment of cheese whey; the anaerobic methane generation for the cheese whey studied was found to be 424 ml CH4/g COD (23.4 1 CH4/l cheese whey); undiluted cheese whey could be treated anaerobically at relatively short HRT values (2.06-4.95 days) without any significant stability problems; HRT values as low as 2-3 days can be used for the anaerobic treatment of cheese whey, with a COD removal efficiency of 95-97% at influent COD concentration of 42 700 +/- 141-55 100 +/- 283 mg/l.