不同诱导条件对结晶产物形貌特征的影响

在流化床反应器中,以含铜废水为处理对象,重点考察了诱导条件改变对结晶系统运行效率及结晶产物形貌特征的影响。结果表明,进水200 mg/L,进药比([Cu2+]/[CO2-3])1∶1.2,p H为10.2的条件下,铜离子去除率可接近100%,诱导晶种表面平滑,诱导颗粒生长成致密杆状晶体结构,以碳酸盐为沉淀剂的诱导结晶系统依赖于体系的p H,高p H体系下发生的共结晶现象是影响系统运行的主要原因;随着进药摩尔比的增加,结晶产物由短杆状向球状转化,晶体机械强度显著降低大量破碎,影响出水水质;进药比1∶1.2,p H为11的条件下,含铜废水浓度为500 mg/L时,系统去除率可达95%以上,微晶产率低于5%。     

磷酸铵镁沉淀法预处理垃圾渗滤液

探讨了用磷酸铵镁沉淀法预处理垃圾渗滤液时,沉淀剂种类、pH值、物质摩尔配比和反应时间等因素对氨氮去除效果的影响。得出了处理氨氮浓度为2 677.34 mg/L的垃圾渗滤液时,在兼顾所用镁盐量尽量低和处理出水氨氮或磷酸盐的残留量都比较低的较佳实验条件为:沉淀剂种类为:MgSO4.7H2O和Na2HPO4.12H2O,反应时间为20 min,pH=9.5,n(Mg)∶n(P)∶n(N)=1.3∶1.15∶1.0。在较佳实验条件下,垃圾渗滤液的NH3-N去除率为97.05%,处理出水PO34--P含量为8.35 mg/L,NH3-N含量为75.86 mg/L。对所得沉淀物进行了成分分析和X-衍射光谱、扫描电镜表征,表明大部分沉淀物为磷酸铵镁物质。     

嗜盐菌的筛选及原油降解性能

油气开发过程含油废液中过高的盐含量是影响其生物处理效果不佳的一个重要因素。针对含油废液的特点,实验从油田废弃泥浆中筛选分离出一株高效嗜盐降解菌,该菌呈杆状,经BIOLOG鉴定系统与分子序列鉴定分析,该菌为芽孢杆菌Bacillus subtilis strain;研究了嗜盐菌的耐盐碱性及原油降解性能,结果表明,该菌适宜于碱性环境,适盐浓度范围为5 000~200 000 mg/L,7 d内对高盐含油模拟废水中原油的降解率高达60%,最佳降解条件为:菌液/培养液体积比1∶12.5,pH=9,NaCl浓度范围为10 000~50 000 mg/L,最佳N源和P源分别为(NH2)2CO和K2HPO4·3H2O。嗜盐菌的研究为高盐含油废液的生物处理拓展了一条新的技术途径。     

NaClO_2/H_2O_2复合吸收剂同时脱硫脱硝实验研究

在喷淋塔中,对NaClO_2/H_2O_2复合吸收剂(简称复合吸收剂)同时去除烟气中的SO_2和NO进行了研究。考察了复合吸收剂摩尔浓度(H_2O_2与NaClO_2摩尔浓度之和)、H_2O_2和NaClO_2的摩尔比、pH、温度和液气比对SO_2和NO去除率的影响。结果表明:保持H_2O_2和NaClO_2的摩尔比为6,当复合吸收剂摩尔浓度小于7mmol/L时,SO_2和NO去除率随着复合吸收剂浓度的升高而增加,当复合吸收剂摩尔浓度大于7 mmol/L时,SO_2和NO去除率基本不再变化;保持复合吸收剂摩尔浓度为7 mmol/L,当H_2O_2和NaClO_2的摩尔比在6以下时,摩尔比越大,SO_2和NO的去除率越高,超过6以后,去除率不再增加;复合吸收剂的氧化性能在pH为5.5时最大;当温度在60℃以下时,随着温度的升高,NO的去除率增加,但当温度超过60℃后,NO的去除率反而降低。综合考虑成本和处理效果,最优化条件为H_2O_2和NaClO_2的摩尔比为6,复合吸收剂摩尔浓度为7 mmol/L,pH为6.0,温度为60℃,液气比为20.0L/m3。在最佳条件下,SO_2和NO去除率分别达到99.5%、84.3%。     

利用高浓度含铬废水制备铬鞣剂

高质量浓度含铬褪铜度液的含铬量高，具有回收利用价值，探索了一条综合处理利用的工艺路线：将含铬废液在合适的条件下，把Cr^3 氧化为Cr^6 ，加入适量的沉淀剂除去杂质，加入工业葡萄糖还原，用碱调节盐基度，生产铬鞣剂。     

膜电解法从模拟酸性蚀刻废液中回收铜粉

酸性蚀刻废液是一种印制电路板制作过程中产生的强酸、高铜的工业废水,对其回收利用具有较高的经济价值。采用膜电解法处理模拟酸性蚀刻废液,在阴极区回收铜粉。研究了铜粉的形成条件,考察了阴极液铜浓度、温度和电流密度对阴极电流效率的影响。结果表明,阴极液的铜浓度在20~25 g/L,温度为45~50℃,电流密度在11~12 A/dm2,阴极的电流效率最高。随着阴极液酸度的增加,铜粉的纯度提高,但阴极电效会降低。为保证较高的铜粉纯度及阴极电效,阴极液的酸度在0.32~0.36 mol/L为宜。     

膜电解工艺处理碱性含铜蚀刻废液

实验对碱性含铜蚀刻废液膜电解工艺处理的可行性开展相关研究,考察了槽电压、电解时间和阳极液pH值等因素对膜电解电流效率的影响,并确定了最佳工艺条件:槽电压3.10 V、电解时间2 h、阳极液初始pH值9.20。在上述最优工艺条件下,膜电解电流效率达91.5%。实验结果表明,该工艺操作方便、简单可行,是处理蚀刻废液、回收铜的有效方法,具有一定的应用价值。     

碱金属盐改性炽热镁渣激冷水合脱硫剂

将炽热镁渣通过激冷水合以及碱金属盐添加剂改性的方法制得脱硫剂,并借助TGA研究改性脱硫剂钙转化率。借助XRD、SEM和BET分析改性脱硫剂物质成分、表面形貌特征以及微观特征,从而获得炽热镁渣激冷水合过程中使用不同碱金属盐改性添加剂的改性机理。结果表明:对镁渣进行激冷水合和加入添加剂改性均可提高脱硫性能;NaCl和Na_2SO_4的加入明显改善了脱硫剂的孔隙结构,Na_2CO_3和K_2CO_3与镁渣水合产物发生化学反应生成CaCO_3并在改性脱硫剂表面附着结晶;水合温度的升高有利于钙转化率的提高。     

混凝剂循环使用及化学混凝处理乳化废液的研究

对乳化废液进行了不完全的化学混凝处理 ,优化出的混凝剂为PAC +PAM ,最佳条件为 :PAC ,1 0～ 2 0g/L ;PAM ,2 0mg/L ;pH ,6 5～ 8 5 ;混凝后的出水COD在 5 0 0～ 5 6 0 0mg/L之间 ,可以用来重新配制乳化液 ,性能指标达到国家规定要求 ;混凝产生的絮渣采用浓硫酸处理 ,每升乳化废液混凝产生的絮渣用 4 5mL浓硫酸 ,处理后回收油品 15mL/L ,混合液可循环使用处理乳化废液 ;将出水回用于配制新乳化液 ,实现了废水循环利用、清洁生产的目的     

UV/Fenton法处理间-甲酚废水

利用UV/Fenton工艺对模拟间-甲苯酚废水进行了处理,研究了H2O2加入量、FeSO4加入量、pH、原水初始COD值、环境温度、反应时间等因素对COD去除率的影响.实验表明:间-甲苯酚浓度为100mg/L、初始COD值251 mg/L的废水,在30℃下,pH为4.Q,[H2O2]/[Fe2 ]=15(质量浓度比),紫外灯照射3 h后,COD去除率达86.3%,若再经Ca(OH)2絮凝沉降,则COD去除率提高到92.6%.同时,对Fenton及UV/Fenton的处理效果进行了比较,实验表明:UV/Fenton的处理效果明显优于Fenton法.     

锌冶炼废渣浸出液硫化法除砷的研究

以硫化钠为沉淀剂,将锌冶炼废渣浸出液中的砷以硫化砷的形式沉淀析出,实验考察了浸出液酸度、硫化钠加入量、反应时间等因素对除砷效率的影响.实验结果表明,当浸出液中游离H2SO4浓度为3 mol/L,Na2S·9H2O投加量为16.1 g/L(浸出液),反应时间为30 min时,浸出液中的砷去除率达到99.3%,较好地解决了...     

填料塔中Na_2CO_3吸收高浓度H_2S的传质特性

在填料吸收塔中考察了Na2CO3溶液吸收高浓度H2S气体的气液传质特性。通过测量填料塔进出口气体中H2S浓度计算了Na2CO3溶液吸收高浓度H2S气体的总体积传质系数(KGa),并研究了进气流速、吸收液流量、吸收温度和吸收液浓度对KGa的影响。结果表明,KGa随Na2CO3浓度、吸收液流量的增加而增加,随吸收温度、进气流速的升高而降低;在高浓度H2S吸收过程中液相传质阻力不能忽略。     

Simultaneous removal of phosphorus and potassium from synthetic urine through the precipitation of magnesium potassium phosphate hexahydrate

This study investigated the simultaneous removal of P and K from synthetic urine through the precipitation of magnesium potassium phosphate hexahydrate (MPP, MgKPO₄·6H₂O) in bench-scale experiments. Results show that the removal efficiencies of P and K are mainly determined by the solution pH and the molar ratio of Mg:K:P. Co-precipitation of struvite-type compounds, i.e., magnesium ammonium phosphate hexahydrate (MAP, MgNH₄PO₄·6H₂O), magnesium sodium phosphate heptahydrate (MSP, MgNaPO₄·7H₂O), and MPP, was confirmed by analysis of the solid precipitates using a Scanning Electron Microscope/Energy Dispersive X-ray Apparatus and an X-ray Diffractometer. The co-precipitation significantly influenced the removal of K. As much ammonium as possible should be removed prior to MPP precipitation because MAP had higher tendency to form than MPP. The inevitable co-precipitation of MPP and MSP resulted in the addition of more MgCl₂·6H₂O and Na₂HPO₄·12H₂O to obtain the high removal of K. In total, the removal efficiencies of P and K were 77% and 98%, respectively, in the absence of ammonium when pH was 10 and the molar ratio of Mg:K:P was 2:1:2. The results indicate that the MPP precipitation is an efficient method for the simultaneous removal of P and K to yield multi-nutrient products.     

钛基IrO2-SnO2电极在烟气海水脱硫恢复系统中的应用

采用浸渍-热分解法制备了含IrOx-TiO2中间层的IrO2-SnO2电极,得到的电极具有较高的析氯电催化活性和较强的稳定性,并通过电化学氧化法对Na2SO3海水脱硫模拟液进行处理,考察了电流密度、温度、pH值和电解时间等电解工艺参数对Na2SO3去除率和化学需氧量COD的影响.结果表明,在电流密度为200 mA/cm...     

微波辅助双氧水氧化降解水中磺胺二甲嘧啶

采用微波辐照技术辅助双氧水氧化降解水中磺胺二甲嘧啶（SM2）,研究了微波辅助双氧水氧化降解水中SM2的影响因素。结果表明,单纯使用微波辐照并不能显著降解SM2,而微波辐照可显著促进双氧水对SM2的氧化作用,提高SM2的降解率。在初始浓度为50 mg/L,微波功率为900 W,加入0.25 mL质量分数为30%的双氧水,pH值为4的条件下辐照6 min,SM2的降解率可达96.5%,COD去除率为72%。     

原位水解生成的羟基氧化铁凝聚吸附除磷效能与机制简

将不同摩尔比Fe³⁺与OH^-（[Fe³⁺]：[OH^-]=1：0、1：1、1：2和1：3）反应获得原位水解生成的羟基氧化铁（in situ FeO_xH_y）,研究了具有不同水解程度的羟基氧化铁对凝聚吸附除磷效能与机制。研究显示,In situ FeO_xH_y对磷的去除率随铁投量增大而升高,且均在中性pH范围内具有最佳除磷效果;在相同铁投量条件下,磷去除率随着[OH^-]：[Fe³⁺]的升高而降低;当体系碱度较低时（pH<6）,引入OH^-可促进Fe³⁺水解而提高除磷效果。4种羟基氧化铁均可在15 s内可快速吸附磷,且吸附过程符合准二级动力学模型;Freundlich模型均可很好地描述磷在4种羟基氧化铁表面的吸附行为。磷酸盐吸附后,In situ FeO_xH_y表面Zeta电位明显降低,且[Fe³⁺]：[OH^-]为1：0的羟基氧化铁降低最为显著。结合MINITEQ计算软件磷酸盐、铁盐形态分析结果显示,对于碱度较低的体系,通过投加一定量OH^-可促进Fe³⁺水解,进而使得其更易与水中H₂PO₄^-与HPO₄^2-结合,生成具有多核羟基的磷酸铁络合物,进而提高除磷效果。     

O3/H2O2处理嘧啶废水的研究

采用O3/H2O2法对嘧啶废水进行处理,考察了不同反应条件对嘧啶和COD去除率的影响,并对O3/H2O2降解嘧啶的反应机制和动力学进行了初步探讨.实验结果表明,在pH值为11,反应时间为70 min,O3流量为4g/h,H2O2投加量为50 mmol/L的条件下,废水的嘧啶和COD的去除率分别达到86.46%和74.9...     

A novel application of H2O2-Fe(II) process for arsenate removal from synthetic acid mine drainage (AMD) water

Batch experiments were carried out to investigate the influences of H₂O₂/Fe(II) molar ratio, pH, sequence of pH adjustment, initial As(V) concentration, and interfering ions on As(V) removal in H₂O₂-Fe(II) process from synthetic acid mine drainage (AMD). The optimum H₂O₂/Fe(II) molar ratio was one for arsenate removal over the pH range of 4-7. Arsenate removal at pH 3 was poor even at high Fe(II) dosage due to the high solubility of Fe(III) formed in situ. With the increase of Fe(II) dosage, arsenate removal increased progressively before a plateau was reached at pH 5 as arsenate concentration varied from 0.05 to 2.0 mg L⁻¹. However, arsenate removal was negligible at Fe/As molar ratio <3 and then experienced a striking increase before a plateau was reached at pH 7 and arsenate concentration ≥1.0 mg L⁻¹. The co-occurring ions exerted no significant effect on arsenate removal at pH 5. The experimental results with synthetic AMD revealed that this method is highly selective for arsenate removal and the co-occurring ions either improved arsenate removal or slightly depressed arsenate removal at pH 5-7. The extended X-ray absorption fine structure (EXAFS) derived As-Fe length, 3.27-3.30 Å, indicated that arsenate was removed by forming bidentate-binuclear complexes with FeO(OH) octahydra. The economic analysis revealed that the cost of the H₂O₂-Fe(II) process was only 17-32% of that of conventional Fe(III) coagulation process to achieve arsenate concentration below 10 μg L⁻¹ in treated solution. The results suggested that the H₂O₂-Fe(II) process is an efficient, economical, selective and practical method for arsenate removal from AMD.     

臭氧辅助UV/Fenton法处理电镀添加剂生产废水

采用臭氧辅助光芬顿法处理电镀添加剂生产废水,考察双氧水、FeSO₄·7H₂O、pH和反应时间等因素对废水COD和UV₂₅₄去除的影响。实验结果表明,pH=4,臭氧通入量为0.25 g,双氧水的投加量93.3 mL/L,FeSO₄·7H₂O投加量为5.3 g/L,最佳反应时间为30 min,COD和UV₂₅₄去除率分别达到92.64%和87.95%。这表明,臭氧辅助光芬顿法对电镀添加剂生产废水处理效果显著,处理时间大大减少。     

Photooxidative removal of the herbicide Acid Blue 9 in the presence of hydrogen peroxide: modeling of the reaction for evaluation of electrical energy per order (EEO)

The present work deals with photooxidative removal of the herbicide, Acid Blue 9 (AB9), in water in the presence of hydrogen peroxide (H₂O₂) under UV light illumination (30 W). The influence of the basic operational parameters such as amount of H₂O₂, irradiation time and initial concentration of AB9 on the photodegradation efficiency of the herbicide was investigated. The degradation rate of AB9 was not appreciably high when the photolysis was carried out in the absence of H₂O₂ and it was negligible in the absence of UV light. The photooxidative removal of the herbicide was found to follow pseudo-first-order kinetic, and hence the figure-of-merit electrical energy per order (E_Eo) was considered appropriate for estimating the electrical energy efficiency. A mathematical relation between the apparent reaction rate constant and H₂O₂ used was applied for prediction of the electricity consumption in the photooxidative removal of AB9. The results indicated that this kinetic model, based on the initial rates of degradation, provided good prediction of the E_Eo values for a variety of conditions. The results also indicated that the UV/H₂O₂ process was appropriate as the effective treatment method for removal of AB9 from the contaminated wastewater.