Seasonal variations and trends in concentrations of filter-collected polycyclic aromatic hydrocarbons (PAH) and mutagenic activity in the San Francisco Bay area

Air monitoring in the San Francisco Bay Area was carried out to measure outdoor community air concentrations of polycyclic aromatic hydrocarbons (PAH) and mutagenic activity (mutagenicity) in particulate organic matter (POM). Monitoring began in 1979 and is currently conducted at six stations. PAH and mutagenicity tests were performed on organic extracts prepared from high volume (hi-vol) filters composited every four months, by meterological season. PAH were determined by high pressure liquid chromatography (HPLC) with fluorescence and ultraviolet detection. Mutagenicity was measured in the Ames Salmonella bioassay using strain TA98 with and without metabolic activation. The nine-year mean concentration of benzo(a)pyrene (BaP) was 0.4 ng/m3. The mutagenicity of this amount of BaP accounted for only about 0.2% of the observed mutagenicity in POM and other measured PAH accounted for even less. Concentrations of PAH and mutagenicity were three to nine times higher during the winter than during other seasons. Year-to-year wintertime trends in several PAH were also seen. Early in the 1980s, winter concentrations of BaP and benzo (g,h,i)perylene increased. However since the mid-1980's, their concentrations have fallen. The decrease in PAH concentrations may be the result of an increasing proportion of vehicles with relatively low organic emissions. In contrast to PAH, mutagenicity did not show significantly year-to-year time trends.     

In vitro EROD induction equivalency factors for the 10 PAHs generally monitored in risk assessment studies in The Netherlands

The ethoxy resorufin dealkylase (EROD) inducing potency of 10 polycyclic aromatic hydrocarbons (PAHs) is measured in the H4IIE in vitro bioassay and the results are compared to those reported in literature. The selected PAHs varied considerably in their potency to induce EROD activity. Anthracene (Ant) and phenanthrene (Phe) showed consistently no response. Naphthalene (Nap) showed no or a very weak response on EROD activity. Fluoranthene (Fla) and benzo[g,h,i]perylene (BghiP) showed weak responses at the highest doses. The other PAHs, including indeno[1,2,3-cd]pyrene (IP), benz[a]anthracene (BaA), benzo[a]pyrene (BaP), chrysene (Chr) and benzo[k]fluoranthene (BkF), showed full bell shaped dose-response curves. BaP EROD induction equivalency factors (BaP-1EF) were calculated and increased in the order Ant approximately Phe < Fla < Nap < BghiP < IP < BaA < BaP < Chr < BkF. Comparison of BaP-IEFs based on 50% effect concentration (EC50) or lowest effect concentration (LEC), yielded a significant relationship between both methods described by the equation log(BaPIEF(EC50) = 0.55 x log(BaPIEF(LEC)) + 0.07 (r2 = 0.913). BaP-IEFs as derived from our measurements and as reported in literature and measured in other in vitro assays deviated up to a factor of 17 among the different studies, but the potency rankings were comparable. For the PAH mixture as on average present in the human diet an overall tetrachlorodibenzo-p-dioxin (TCDD)-IEF of 1 x 10(-4) was estimated. The total PAH based TCDD induction equivalents (IEQ) intake then was calculated 300 pg/day, which is approximately 2 times higher then the PHAH based TCDD-EQ intake reported for humans.     

A Comparison of Mass,Lead, Sulfate,and Nitrate Concentrations in a Field Study Using Dichotomous,Size-Selective,and Standard Hi-Vol Samplers

Air monitoring In the San Francisco Bay Area was carried out to measure outdoor community air concentrations of poly cyclic aromatic hydrocarbons (PAH) and mutagenlc activity (mutagenlclty) In participate organic matter (POM). Monitoring began In 1979 and Is currently conducted at six stations. PAH and mutagenlclty tests were performed on organic extracts prepared from high volume (hl-vol) filters composited every four months, by meteorological season. PAH were determined by high pressure liquid chromatography (HPLC) with fluorescence and ultraviolet detection. Mutagenlclty was measured In the Ames Salmonella bloas-say using strain TA98 with and without metabolic activation. The nine-year mean concentration of benzo(a)pyrene (BaP) was 0.4 ng/m³. The mutagenlcfty of this amount of BaP accounted for only about 0.2% of the observed mutagenicity In POM and other measured PAH accounted for even less. Concentrations of PAH and mutagenlclty were three to nine times higher during the winter than during other seasons. Year-to-year wintertime trends In several PAH were also seen. Early In the 1980s, winter concentrations of BaP and benzo (g,h,i)perylene Increased. However since the mld-1980’s, their concentrations have fallen. The decrease In PAH concentrations may be the result of an Increasing proportion of vehicles with relatively low organic emissions. In contrast to PAH, mutagenlcfty did not show significant year-to-year time trends.     

Evaluation of high volume particle sampling and sample handling protocols for ambient urban air mutagenicity determinations.

An investigation of high volume particle sampling and sample handling procedures was undertaken to evaluate variations of protocols being used by the U.S. Environmental Protection Agency. These protocols are used in urban ambient air studies which collect ambient and source samples for subsequent mutagenicity analysis of the organic extracts of the aerosol fraction. Specific protocol issues investigated include: (a) duration of sampling period, (b) type of filter media used to collect air particles, (c) necessity for cryogenic field site storage and dry ice shipping of filter samples, and (d) sample handling at the receiving laboratory. Six PM10 Hi-Vol samplers were collocated at an urban site in downtown Durham, North Carolina and operated simultaneously to evaluate 12 h versus 24 h collection periods and filter media choices of glass fiber, Teflon impregnated glass fiber (TIGF), and quartz fiber. Filters from the samplers plus field blanks were collected during each of 25 sampling periods. TIGF filters from two samplers were immediately placed on dry ice in the field and transported directly to cryogenic storage. TIGF, quartz, and glass fiber filters from three samplers were transported at ambient and maintained at room temperature for three to six days prior to cryogenic storage. One TIGF sample, which was collected on a previously tared filter, was subjected to controlled environment equilibration (40 percent relative humidity, 22 degrees C) for 8 to 24 h and weighed prior to cryogenic storage. All filters were subsequently stored at -70 degrees C to -80 degrees C prior to a one-time extraction and Salmonella (Ames) mutagenicity bioassay of the entire sample set.(ABSTRACT TRUNCATED AT 250 WORDS)     

Phase distribution and artifact formation in ambient air sampling for polynuclear aromatic hydrocarbons

Laboratory and field sampling experiments were conducted to determine the phase-distribution of polynuclear aromatic hydrocarbons (PAH) in the ambient atmosphere and to determine the potential for artifact formation due to volatilization and ozone (O₃) reaction during normal sampling conditions. The study was conducted in two segments to investigate both summer and winter ambient temperature effects. The winter measurements reflect stronger association of PAH with the particulate phase than the summer data, but data from both seasons show appreciable filter losses due to volatilization of phenanthrene, anthracene, fluoranthene, benz(a)anthracene and chrysene. No evidence was found for volatilization of the heavier PAH, including benzo(e)pyrene, benzo(a)pyrene, indeno(l,2,3-c,d)pyrene, benzo(g,h,i)perylene and coronene. Although O₃ reacted readily with particulate matter that was freshly spiked with PAH in the laboratory experiments, no evidence was found for reaction of O₃ with particulate matter during the field sampling experiments.     

Oxidant denuder sampling for analysis of polycyclic aromatic hydrocarbons and their oxygenated derivates in ambient aerosol: evaluation of sampling artefact

The concentrations of some polycyclic aromatic hydrocarbons (PAH) and oxygenated PAH (O-PAH) can be changed by oxidation reactions during sampling. This can lead to an over- or underestimation of the corresponding adverse health effects. The aim of this study was the evaluation of these sampling artefacts. The potential of using an oxidant denuder was shown by parallel low-volume sampling with and without MnO₂ ozone denuder. Twenty-three PAH and 11 O-PAH in ambient air were analysed, both in the vapour and particulate phase. The denuder was proven to be highly efficient for stripping ozone from air while causing no significant particle losses. In general, the concentrations of 5- to 7-ring PAH, which are predominantly associated with particles, were underestimated in non-denuded samples. The highest losses due to reaction with ozone and other atmospheric oxidants were observed for benzo[a]pyrene and perylene. Concurrently, the concentrations of most of the mainly particle-associated 4- to 5-ring O-PAH were higher in the non-denuded samples. The denuder did not only remove ozone, moreover other gaseous species such as more volatile PAH and O-PAH were partially oxidized on the catalytic surface, too. Degradation of PAH and concurrent degradation/formation reactions of O-PAH occurred. The corresponding reactivities of selected PAH and O-PAH are discussed.     

Degradation mechanisms of benzo[a]pyrene and its accumulated metabolites by biodegradation combined with chemical oxidation

A high degradation extent of benzo[a]pyrene (BaP) should not be considered as the sole desirable criterion for the bioremediation of BaP-contaminated soils because some of its accumulated metabolites still have severe health risks to human. Two main metabolites of BaP, benzo[a]pyrene-1,6-quinone (BP1,6-quinone) and 3-hydroxybenzo[a]pyrene (3-OHBP) were identified by high performance liquid chromatography (HPLC) with standards. This study was the first time that degradation of both BaP and the two metabolites was carried out by chemical oxidation and biodegradation. Three main phases during the whole degradation process were proposed. Hydrogen peroxide-zinc (H(2)O(2)-Zn), the fungus - Aspergillus niger and the bacteria - Zoogloea sp. played an important role in the different phases. The degradation parameters of the system were also optimized, and the results showed that the effect of degradation was the best when fungus-bacteria combined with H(2)O(2)-Zn, the concentration range of BaP in the cultures was 30-120mg/l, the initial pH of the cultures was 6.0. However, as co-metabolites, phenanthrene significant inhibited the degradation of BaP. This combined degradation system compared with the conventional method of degradation by domestic fungus only, enhanced the degradation extent of BaP by more than 20% on the 12d. The highest accumulation of BP1,6-quinone and 3-OHBP were reduced by nearly 10% in the degradation experiments, which further proved that the combined degradation system was more effective as far as joint toxicity of BaP and its metabolites are concerned.     

Ozone measurements in South Carolina using passive samplers

Passive samplers with two different collection substrates were used to obtain an average ozone concentration for 1 month during the summer of 2002 for each South Carolina county. One sampler contained a filter coated with indigo carmine, whose color fades when exposed to ozone. The fading was measured by reflectance spectroscopy. The other sampler contained filters that were coated with nitrite, which is oxidized to nitrate when exposed to ozone. The nitrate was measured by ion chromatography. Calibration curves were developed for the two methods by comparing color fading from indigo carmine and nitrate ion concentration from the nitrite filter with ambient ozone concentration measured by a co-located reference continuous UV ozone analyzer. These curves were used to calculate integrated ozone concentrations for samplers distributed across South Carolina. Using the indigo carmine method, the average ozone concentrations ranged from 21 to 64 ppb (average = 46 +/- 7.9 ppb, n = 58) across the 46 counties in the state during one summer month of 2002. Concentrations for the same time period from the nitrite-coated filters ranged from 23 to 62 ppb (average = 41 +/- 8.1 ppb, n = 58). Also for the same time period, the 23 continuous UV photometric ozone monitors operated by the South Carolina Department of Health and Environmental Control at sites within 10 miles of some of the passive monitors showed ozone concentrations ranging from 28 to 50 ppb (average = 39 +/- 6.3 ppb, n = 22).     

Preliminary evidence of the role of hydrogen peroxide in the degradation of benzo[a]pyrene by a non-white rot fungus Fusarium solani

In order to study the enzymatic mechanisms involved in the successive steps of BaP degradation by a Deuteromycete fungus Fusarium solani, we developed an indirect approach by using inhibitors of enzymes. We used either specific inhibitors of peroxidases (i.e. salicylhydroxamic acid) and of cytochrome P-450 (i.e. piperonyl butoxyde) or inhibitors of both enzymes (i.e. potassium cyanide). Surprisingly, no expected decrease of BaP degradation was observed with most inhibitors tested. On the contrary, more BaP was degraded. Only butylated hydroxytoluene, which acts as a free radical scavenger, inhibited BaP degradation. The inhibition of these enzymes, which use H(2)O(2) as a cosubstrate, might have resulted in an increase of hydrogen peroxide availability in the fungal cultures. This enhancement could induce formation of reactive oxygen species (ROS) which might be the agents that initiate benzo[a]pyrene oxidation. This study proposed a hypothetic alternative metabolic pathway involved in PAH metabolism by Fusarium solani.     

The temporal variability of the profile of carcinogenic polycyclic aromatic hydrocarbons in urban air: a study in a medium traffic area in Rome, 1993–1998

The constancy, both temporal and spatial, of the profile of polycyclic aromatic hydrocarbons (PAHs) relative to benzo[a]pyrene (BaP) is a prerequisite to using the BaP-indicator approach in the carcinogenic risk assessment for PAHs. The principal aim of this study was to provide a contribution to validate this approach, by studying the variability of the profile at a typical urban site through a multi-year data set and by comparing the profiles available for different cities. Seven carcinogenic PAHs (benz[a]anthracene, benzo[b+j+k]fluoranthenes, BaP, indeno[1,2,3-cd]pyrene, dibenz[a,h]anthracene) were determined in PM₁₀ 24-h samples collected every third day at a road site; moreover, benzo[e]pyrene was determined as a reference PAH due to its stability. The profile was found stable from year to year. Besides, it was similar to those recently found in other European cities (observed differences within a factor of four) and to those elaborated from earlier (1970s–1980s) investigations. The substantial similarity of profiles, both temporal (on an annual basis) and spatial, supports the validity of the BaP-indicator approach. Large PAH-to-PAH differences were, however, found in the seasonal pattern of profile: they were explained by the different atmospheric degradability of PAHs, whose effect is enhanced under the meteoclimatic conditions typical of the European Mediterranean countries. PAH annual means showed a slight declining trend since 1994. In the last sampling year, mean concentration of BaP was 1.2 ng m⁻³. Within-year differences among monthly averaged PAH concentrations were observed, as large as up to 44-fold for BaP, underlining the need for whole-year monitoring.     

Ozone Measurements in South Carolina Using Passive Samplers

Abstract

Passive samplers with two different collection substrates were used to obtain an average ozone concentration for 1 month during the summer of 2002 for each South Carolina county. One sampler contained a filter coated with indigo carmine, whose color fades when exposed to ozone. The fading was measured by reflectance spectroscopy. The other sampler contained filters that were coated with nitrite, which is oxidized to nitrate when exposed to ozone. The nitrate was measured by ion chromatography.

Calibration curves were developed for the two methods by comparing color fading from indigo carmine and nitrate ion concentration from the nitrite filter with ambient ozone concentration measured by a co-located reference continuous UV ozone analyzer. These curves were used to calculate integrated ozone concentrations for samplers distributed across South Carolina.

Using the indigo carmine method, the average ozone concentrations ranged from 21 to 64 ppb (average = 46 ± 7.9 ppb, n = 58) across the 46 counties in the state during one summer month of 2002. Concentrations for the same time period from the nitrite-coated filters ranged from 23 to 62 ppb (average = 41 ± 8.1 ppb, n = 58). Also for the same time period, the 23 continuous UV photometric ozone monitors operated by the South Carolina Department of Health and Environmental Control at sites within 10 miles of some of the passive monitors showed ozone concentrations ranging from 28 to 50 ppb (average = 39 ± 6.3 ppb, n = 22).     

Molecular evidence for benzo[a]pyrene and naphthalene genotoxicity in Trifolium repens L

Polycyclic aromatic hydrocarbons (PAHs) are among the most dangerous environmental contaminants due to their toxic, carcinogenic and mutagenic effects. Although there are many data in literature that detail the effects of PAHs on animals, little is known about their action on higher plants which are often used as bioindicators. The aim of the present study was to evaluate the genotoxicity of two different PAHs, benzo[a]pyrene (BaP) and naphthalene (Naph), on Trifolium repens L. Clover plants were exposed to soil which had been artificially contaminated with three concentrations of BaP (5, 10 and 20 microg g-1) or Naph (25, 50 and 100 microg g-1). After 15 days, changes in the DNA content and sequence of roots and shoots were evaluated by flow cytometry (FCM) and amplified fragment length polymorphism (AFLP). Root and shoot dry weight were also determined to assess plant growth. Results showed that BaP and Naph were both genotoxic for white clover, inducing significant changes in root and shoot DNA sequence. Damage was more severe in the root than in the shoot suggesting that the translocation of these compounds and their genotoxic metabolites was limited. Ploidy alterations were not detected and the extent of damage caused by all the tested PAH concentrations was not sufficient to affect plant development.     

Benzo[a]pyrene degradation by Sphingomonas yanoikuyae JAR02

Batch experiments were conducted to characterize the degradation of benzo[a]pyrene, a representative high molecular weight (HMW) polycyclic aromatic hydrocarbon (PAH), by Sphingomonas yanoikuyae JAR02. Concentrations up to the solubility limit (1.2 microg l(-1)) of benzo[a]pyrene were completely removed from solution within 20 h when the bacterium was grown on salicylate. Additional experiments with [(14)C]7-benzo[a]pyrene demonstrated 3.8% mineralization over 7 days when salicylate was present is solution, and one major radio-labeled metabolite was observed that accounted for approximately 10% of the initial radio-label. Further characterization of the radio-labeled metabolite using HPLC/MS and HPLC/MS/MS identified radio-labeled pyrene-8-hydroxy-7-carboxylic acid and unlabeled pyrene-7-hydroxy-8-carboxylic acid as novel ring-cleavage metabolites, and a benzo[a]pyrene degradation pathway was proposed. Results indicate that biostimulation of HMW PAH degradation by salicylate, a water-soluble, non-toxic substrate, has significant potential for in situ bioremediation.     

Nitration of polycyclic aromatic hydrocarbons adsorbed to different carriers in a fluidized bed reactor

The reactivity of selected polycyclic aromatic hydrocarbons (PAH) adsorbed to various surfaces has been studied. PAH were adsorbed to silica, alumina or charcoal particles and exposed to ambient concentrations of NO₂ in air in a fluidized bed reactor. The reaction products were analyzed by capillary gas chromatography and gas chromatograpy/mass spectrometry.The results show that silica is a more reactive surface than alumina. The charcoal used showed to be very adsorbtive and too little material was recovered for analyses. The reactivity of the PAH compounds studied decrease in the order perylene > benzo(a)pyrene > pyrene > chrysene > fluoranthene and phenanthrene. The relevance of these results to the assessment of the possible formation of nitro-PAH in the atmosphere is discussed.     

Urban-Center CO Air Quality Projections

The distribution of mutagenic activity and nitroaromatic components of polycyclic organic matter (POM) in ambient air at industrial, urban, suburban, rural, and remote sites was studied using organic extracts from high volume aerosol samples. Direct-acting mutagens including 1-nitropyrene (1-NP), dinitropyrenes (DNP), and hydroxynitropyrenes (HNP) were measured by high performance liquid chromatography while the mutagenicity was determined in the Salmonella bioassay with strain TA-98. Benzo(a)pyrene (BaP), one of the possible precursors of nitroaromatic compounds in POM, was also measured. In comparing samples from a range of sites, TSP and the concentration of BaP per mass of particulate matter decreased, as expected, at greater distances from urban and industrial combustion sources. However, the concentrations of polar nitroaromatic POM compounds per mass of particles were higher at a remote site than in nonindustrial urban and suburban areas. The mutagenicity in particulate matter extracts from the remote area was predominantly (>90 percent) in the very polar fractions. There were also high atmospheric levels of nitroaromatic compounds and mutagenicity in heavily industrialized areas. These observations may reflect the influences of source emissions, atmospheric transformations of POM compounds, and ther atmospheric processes on the composition of ambient suspended particulate matter.     

Evidence for the transformation of polycyclic organic matter in the atmosphere

The ratios of 1-nitropyrene and hydroxynitropyrenes to inert marker species (fine particulate lead, selenium, and elemental carbon) were considerably higher at a remote site on Bermuda than in Delaware. The results suggested that these nitroaromatic POM are formed in atmospheric reactions. The ratio of benzo(a)pyrene to marker species was not significantly different at the two sites. This result did not reflect the expected loss of BaP in atmospheric photochemical reactions.     

Impact of polycyclic aromatic hydrocarbon emissions from medical waste incinerators on the urban atmosphere

In this study, polycyclic aromatic hydrocarbon (PAH) emissions from two batch-type medical waste incinerators (MWIs), one with a mechanical grate and the other with a fixed grate, both operated by a medical center, were assessed. Both MWIs shared the same air-pollution control devices (APCDs), with an electrostatic precipitator and a wet scrubber installed in series. Results show that when APCDs were used, total PAHs and total benzo[a]pyrene equivalent (total BaP(eq)) emission concentrations of both MWIs were reduced from 2220 to 1870 microg/m3 and 50 to 12.4 microg/m3, respectively. We used the Industrial Source Complex Short Term model (ISCST) to estimate the ground-level concentrations of the residential area and the traffic intersection located at the downwind side of the two MWIs. For the traffic intersection, we found both total PAHs and total BaP(eq) transported from MWIs to both studied areas were not significant. For the residential area, similar results were found when APCDs were used in MWIs. When APCDs were not included, we found that total PAHs transported from MWIs accounted for < 12%, but total BaP(eq) accounted for > 90%, of the on-site measured concentrations. These results suggest that the use of proper APCDs during incineration would significantly reduce the carcinogenic potencies associated with PAH emissions from MWIs to the residential area.     

Exploring relationships between outdoor air particulate-associated polycyclic aromatic hydrocarbon and PM2.5: A case study of benzo(a)pyrene in California metropolitan regions

Polycyclic aromatic hydrocarbons (PAHs) and particulate matter (PM) are co-pollutants emitted as by-products of combustion processes. Convincing evidence exists for PAHs as a primary toxic component of fine PM (PM_2.5). Because PM_2.5 is listed by the US EPA as a “Criteria Pollutant”, it is monitored regularly at sites nationwide. In contrast, very limited data is available on measured ambient air concentrations of PAHs. However, between 1999 and 2001, ambient air concentrations of PM_2.5 and benzo(a)pyrene (BaP) are available for California locations. We use multivariate linear regression models (MLRMs) to predict ambient air levels of BaP in four air basins based on reported PM_2.5 concentrations and spatial, temporal and meteorological variables as variates. We obtain an R² ranging from 0.57 to 0.72 among these basins. Significant variables (p<0.05) include the average daily PM_2.5 concentration, wind speed, temperature and relative humidity, and the coastal distance as well as season, and holiday or weekend. Combining the data from all sites and using only these variables to estimate ambient BaP levels, we obtain an R² of 0.55. These R²-values, combined with analysis of the residual error and cross validation using the PRESS-statistic, demonstrate the potential of our method to estimate reported outdoor air PAH exposure levels in metropolitan regions. These MLRMs provide a first step towards relating outdoor ambient PM_2.5 and PAH concentrations for epidemiological studies when PAH measurements are unavailable, or limited in spatial coverage, based on publicly available meteorological and PM_2.5 data.     

Ambient air concentrations of polycyclic aromatic hydrocarbons,fluoride, suspended particles and particulate carbon in areas near aluminum production plants

Concentrations of airborne polycyclic aromatic hydrocarbons (PAH), fluoride, suspended particles and particulate carbon were determined in four different residential areas near aluminum industries. Two of the areas were exposed to pollutants from primary aluminum production, the third area was close to a plant manufacturing electrodes for the aluminum industry while the fourth area received pollutants from the production of aluminum as well as electrodes. The sampling time was 24 h and the samples were collected every eighth day for about 16 months. The concentrations of PAH were high compared to levels in other polluted areas with industry and dense traffic. The average concentrations for benzo(a)pyrene (BaP) were above 10 ngm⁻³, which has been proposed as a guideline in some countries, at all sites. The highest air concentration of BaP measured in the present study was 160 ng m⁻³. At two of the stations the fluoride concentrations exceeded the 24-h national guideline of 25 μgm⁻³, which has been set to protect human health. In a few cases the concentrations of suspended particles were high while the levels of carbon agreed with concentrations reported in urban and residential areas in U.S.A. The concentrations varied with time and the variation was caused mainly by the changes of the meteorological conditions. The frequency distributions were skew for all components and close to logarithmic normal. PAH were well correlated with fluoride, which is an aluminum production tracer, indicating that they are of the same origin. The aluminum industry did not seem to be the main source of particulate matter and carbon in air. Apportionment studies of the organic pollutants were carried out by cluster analysis, and the results showed that the aluminum production is the main source to the PAH in ambient air in these areas.     

Polycyclic aromatic hydrocarbons air levels in Florence,Italy, and their correlation with other air pollutants

Benzo(a)pyrene [B(a)P] air levels were measured in Florence (Italy) in the period 1992-2001. For the period 1999-2000 seven polycyclic aromatic hydrocarbons (PAH) (benzo(a)anthracene, crysene, benzo(a)pyrene (B(a)P), benzo(b)fluoranthene (B(b)F), benzo(k)fluoranthene, dibenzo(a,h)anthracene (DBA) and benzo(g,h,i)perylene (BGP)), were measured in the air in four different sites (one with heavy traffic (A), one in a park (B), one in a residential area (C) and one in a hill area (D)). B(a)P levels were elevated in 1992-1998 (maximum average value of winter months: 5.8 ng/ m3) but a decreasing trend was observed in the following years, probably due to improvement in vehicle emissions. The sum of PAH in the air in the period 1999-2000 was about one order of magnitude lower in the hill site (D) relative to the urban sites, and residential areas (B and C) had values 2.5-3 times lower compared to site A with a heavy traffic. PAH concentrations decreased in the warmer seasons of 2000 in all sites. A negative correlation was found between PAH levels and ozone. A positive correlation with carbon monoxide (CO) (r = 0.862, P < 0.001) and low B(a)P/BGP ratios, ranging from 0.44 to 0.51, indicated that vehicular traffic was the major PAH source in all monitored sites. Using B(a)P(TEF) values (toxic equivalency factors) for evaluating the biological activity of PAH, we found that the highest PAH contributors in terms of potential air carcinogenic activity were B(a)P and DBA. Therefore, in addition to B(a)P, DBA concentration should be considered in the evaluation of air quality in terms of PAH contamination.