Smog Chamber Simulation of Los Angeles Pollutant Transport

The body of information presented in this paper is directed to those individuals concerned with the effect of urban pollution on downwind areas. In the absence of any evidence, it has been widely assumed that increasing NO _x emissions have caused oxidant levels to increase downwind of Los Angeles, i.e., Riverside and San Bernardino. This smog chamber study simulated pollutant transport from Los Angeles to the downwind areas by irradiating a typical Los Angeles hydrocarbon/NO _x mixture for extended periods of time. The smog chamber experiments were extended to 22 hours to obtain an integrated light intensity equal to that which occurs in the Los Angeles area. The effects of variations of nitrogen oxide emissions on an aged air mass were examined. The results show that downwind oxidant levels are only slightly affected by large changes in NO _x emissions. However, it is clear that reduced nitrogen oxide emissions will lead to an increase in oxidant in downtown Los Angeles.     

A Portable Electrical Analyzer for Size Distribution Measurement of Submicron Aerosols

An electrical aerosol analyzer capable of performing rapid, in situ size distribution measurement on aerosols from 0.003 to 1 μm diameter has been described. The instrument is based on the “diffusion charging-mobility analysis” principle first described by Whitby and Clark. The prototype instrument has a total volume of 3.75 ft³ and a total weight of 60 lb, and is sufficiently portable to be used on small airplanes and ground based vehicles for mobile air pollution studies. The paper describes the design, operation, and performance of the instrument. Sample data are presented showing the size distributions of aerosols measured by the instrument on board a small research aircraft over the Los Angeles basin at several different altitudes. In addition, data are presented showing the size distribution of smog chamber aerosols and aerosols produced by a conventional Collison atomizer.     

A photochemical model for air quality assessment: Model description and verification

A hybrid Eulerian-Lagrangian, photochemical model has been developed for the assessment and prediction of the impact of large point sources on air quality. This simple model is based on solving the mass conservation equations which include chemical reaction terms in the cells of a two-dimensional crosswind plane which moves with the air parcel. Testing of the model is done in three ways. First, the chemistry is evaluated using results of smog chamber experiments simulating Melbourne's emissions and meteorological conditions. Second, the accuracy of the emissions inventory is tested using aircraft measurements. Finally the overall performance of the model is evaluated using monitoring station data. In general the model gives good agreement with the measurements, with the predictions for O₃ being somewhat better than those for NO₂. This result was also found in the three-dimensional study of McRae and Seinfeld (1983, Atmospheric Environment17, 501–522) for the Los Angeles area.     

Assessment of tropospheric ozone at an industrial site of Chennai megacity

This paper presents the temporal variation in surface-level ozone (O₃) measured at Gummidipoondi near Chennai, Tamilnadu. The site chosen for the present study has high potential for ozone generation sources, such as vehicular traffic and industrial activities. The site is also located near a hazardous waste management facility. The key sources of nitrogen oxides (NO_x), which are considered to be an important precursor of O₃, include hazardous waste incineration, trucks bringing the hazardous wastes, and vehicles plying on the nearby National Highway 16 (NH 16). The measurements clearly showed diurnal variation, with maximum values observed during the noon hours and minimum values observed when solar radiation was less. The data showed a marked seasonal variation in O₃, with the highest hourly average O₃ concentration (497.2 µg/m³) in the summer season. Consequently, in order to identify the long-range transport sources adding to the increased O₃ levels, backward trajectories were computed using the Hybrid Single Particle Lagrangian Integrated Trajectory (HYSPLIT) model. It was found that the polluted air mass originated from the Southeast Asian region and the Indo-Gangetic Plain. The polluted air mass, which advected large amounts of carbon monoxide (CO) plumes, was analyzed using the Measurement of Pollution in the Troposphere (MOPITT) retrievals. The correlations of O₃ with temperature (r = 0.746; P < 0.01) and solar radiation (r = 0.751; P < 0.01) were strongly positive, and that with NO_x was found to be negative. Stronger correlation of O₃ with NO_x was observed during pre-monsoon months (r = 0.627; P < 0.01) and following hours of photochemical reactions. There were substantial differences in concentrations between weekdays and weekends, with higher nitric oxide (NO) and nitrogen dioxide (NO₂), but lower O₃, concentrations on weekdays. A substantial weekday-weekend difference in O₃, which was higher on weekends, appears to be attributable to lower daytime traffic activity and hence reduced emissions of NO_x to a “NO_x-saturated” atmosphere.

Implications: The assessment of ground-level ozone in an industrial area with hazardous waste management facility is very important, as there is high possibility for more generation of tropospheric ozone. Since the location of the study area is coastal, wind plays a major role in O₃ transportation; hence, the effects of wind speed and wind direction have been studied in different seasons. When compared with the other studies carried out in different places across India, the present study area has recorded much greater O₃ mixing ratio. This study can be useful for setting up control strategies in such industrial areas.     

Application of the Fenton’s process in a bubble column reactor for hydroquinone degradation

The aim of this study was to assess the degradation and mineralization of hydroquinone (HQ) by the Fenton’s process in a bubble column reactor (BCR). The effect of the main operating variables, namely, air flow rate, effluent volume, hydrogen peroxide (H₂O₂) concentration, catalyst (Fe²⁺) dose, initial pH, and temperature, were assessed. For all air flow rates tested, no concentration gradients along the column were noticed, evidencing that a good mixing was reached in the BCR. For the best conditions tested ([H₂O₂] = 500 mg/L, [Fe²⁺] = 45 mg/L, T = 24 °C, Q _air = 2.5 mL/min, pH = 3.0, and V = 5 L), complete HQ degradation was reached, with ~ 39% of total organic carbon (TOC) removal, and an efficiency of the oxidant use—η _H2O2—of 0.39 (ratio between TOC removed per H₂O₂ consumed normalized by the theoretical stoichiometric value); moreover, a non-toxic effluent was generated. Under these conditions, the intermediates and final oxidation compounds identified and quantified were a few carboxylic acids, namely, maleic, pyruvic, and oxalic. As a strategy to improve the TOC removal, a gradual dosage of the optimal H₂O₂ concentration was implemented, being obtained ~ 55% of mineralization (with complete HQ degradation). Finally, the matrix effect was evaluated, for which a real wastewater was spiked with 100 mg/L of HQ; no reduction in terms of HQ degradation and mineralization was observed compared to the solution in distilled water.     

summary of the California aerosol characterization experiment

This report gives a brief summary of the experimental plan and the early results of field observations from the California Aerosol Characterization Experiment (ACHEX). The objectives of the program center on questions of the sources and evolution of aerosols in urban air, as they are superimposed on a natural background, particularly as they relate to visibilitydegradation. The project initially nvolved the use of an elaborately instrumented mobile laboratory combined with a fixed station in San Jose, in Pasadena, and in Riverside, and later incorporated several satellite monitoring stations in the Los Angeles Basin. Intensive field observationswere taken from July 1972 to November 1972 in several urban and nonurban locations between the San Francisco Bay area and the South Coast Basin, covering the Los Angeles area. In a second phase of the ACHEX, aerosols accompanying photochemical smog were studied intensively in the Los Angeles Basin during the period between July and October of 1973. The observations cover a wide variety of parameters including physical and chemical properties of aerosols, pollutant gas concentrations, and meteorological variables. The initial results show the great importance of sulfate, nitrate, noncarbonate carbon, and liquid water to the mass concentration of airborne particles and their relation to reduction in visibility. The anthropogenic contribution to atmospheric aerosols is consistently found to be allocated primarily to the submicron or fine particle size range.     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

Air Analysis: The Standard Dosage-Area Product

The Dosage-Area Product is an areawide smog index obtained by combining contaminant concentration, duration, and areal extent: DAP = c×f×A (ppm × hr × mi²). The first step in developing a DAP is to plot daily contaminant dosages from an air monitoring network and to draw isopleths showing the dosage pattern. The second step is to determine the areas between isopleths and to multiply these areas by the applicable dosage levels. The final step is to sum the above partial products into a single number and to add a type designator indicating the geographic configuration of the dosage pattern. The DAP smog index is a realistic yardstick for measuring areawide smog experience. Reproducible results are obtained at low cost by using standard techniques. The standard DAP smog index is also useful for: analyzing air pollution episodes, estimating contaminant trends, and informing the public.     

The APCA Exhibition

On June 5 and 6 of 1980, two parallel plume oxidation studies were carried out in the vicinity of the Tennessee Valley Authority's Colbert Steam Plant. One study was performed in a smog chamber into which stack gases were injected and mixed with ambient air. The other study included direct airborne sampling of the power plant plume. Atmospheric oxidation rates for the conversion of SO₂ to SO₄ ^2- and the removal rates of NO _x (which is presumably the rate of NO₃ ^- formation) were estimated for both studies. The SO₂ to SO₄ ^2- rate coefficients were found to be 0.022 ± 0.009 h^-1 for both chamber experiments and the first airborne sampling day. For the second day, a rate constant of 0.041 ± 0.052 h^-1 was estimated from the aircraft data. The large deviation in this value is explained by the fact that the plume from the power plant combined and reacted with the urban plume from the city of Florence, AL. The formation of a very large "O3 bulge" on this day is also attributed to the mixed plumes. The first order rate coefficients for NO _x removal were estimated to be 0.27 ± 0.14 h^-1 for both chamber experiments and the first airborne sampling day. A NO _x removal rate could not be determined for the second airborne sampling day.     

Atrazine degradation by fungal co-culture enzyme extracts under different soil conditions

This investigation was undertaken to determine the atrazine degradation by fungal enzyme extracts (FEEs) in a clay-loam soil microcosm contaminated at field application rate (5 μg g^?1) and to study the influence of different soil microcosm conditions, including the effect of soil sterilization, water holding capacity, soil pH and type of FEEs used in atrazine degradation through a 2⁴ factorial experimental design. The Trametes maxima–Paecilomyces carneus co-culture extract contained more laccase activity and hydrogen peroxide (H₂O₂) content (laccase = 18956.0 U mg protein^?1, H₂O₂ = 6.2 mg L^?1) than the T. maxima monoculture extract (laccase = 12866.7 U mg protein^?1, H₂O₂ = 4.0 mg L^?1). Both extracts were able to degrade atrazine at 100%; however, the T. maxima monoculture extract (0.32 h) achieved a lower half-degradation time than its co-culture with P. carneus (1.2 h). The FEE type (p = 0.03) and soil pH (p = 0.01) significantly affected atrazine degradation. The best degradation rate was achieved by the T. maxima monoculture extract in an acid soil (pH = 4.86). This study demonstrated that both the monoculture extracts of the native strain T. maxima and its co-culture with P. carneus can efficiently and quickly degrade atrazine in clay-loam soils.     

Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

Dicarboxylic acids and related compounds in fine particulate matter aerosols in Huangshi,central China

PM_2.5 (particulate matter with an aerodynamic diameter <2.5 μm) samples were collected in Huangshi, central China, from March 2012 to February 2013 and were analyzed for dicarboxylic acids (diacids) and related compounds (DARCs). Oxalic acid (C₂; 416 ng m^?3) was the most abundant species, followed by phthalic (Ph; 122 ng m^?3), terephthalic (tPh; 116 ng m^?3), succinic (C₄; 70.4 ng m^?3), azelaic (C₉; 67.9 ng m^?3), and adipic (C₆; 57.8 ng m^?3) acids. Relatively high abundances of Ph and tPh differed from the distribution in urban and marine aerosols, indicating contributions from nearby anthropogenic sources. Glyoxylic acid (ωC₂; 41.4 ng m^?3) was the dominant oxoacid, followed by 9-oxononanoic (ωC₉; 40.8 ng m^?3) and pyruvic (Pyr; 24.1 ng m^?3) acids. Glyoxal (Gly; 35.5 ng m^?3) was the dominant α-dicarbonyl. Highest average concentrations were found for C₂, ωC₂, and C₉ in autumn, for C₄, for Pyr and C₆ in spring, for Ph, ωC₉, and Gly in summer, whereas the lowest values were observed in winter. Seasonal variations and correlation coefficients of DARCs demonstrate that both primary emissions and secondary production are important sources. Principal component analysis of selected DARCs species suggests that a mixing of air masses from anthropogenic and biogenic sources contribute to the Huangshi aerosols.

Implications: Both primary emissions and secondary production are important sources of diacids and related compounds in PM_2.5 from Huangshi, central China. Principal component analysis of selected diacids in Huangshi aerosols suggests that mixing of air masses from anthropogenic and biogenic sources contribute to ambient aerosols in central China.     

Effects of air/fuel ratio on gas emissions in a small spark-ignited non-road engine operating with different gasoline/ethanol blends

This study investigates the effects of several blends of gasoline and anhydrous ethanol on exhaust emission concentrations of carbon monoxide (CO), total hydrocarbons (HCs), and nitrogen oxides (NO_x) from a small spark-ignited non-road engine (SSINRE). Tests were carried out for different air/fuel equivalence ratios as measured by lambda (λ). A 196 cm³ single-cylinder four-stroke engine-generator operating at a constant load of 2.0 kW was used; pollutant gas concentrations were measured with an automatic analyzer similar to those typically used in vehicle inspections. The results showed that as the ethanol content of the mixture increased the concentrations of CO, HCs, and NO_x reduced by 15, 53, and 34%, respectively, for values of λ < 1 (rich mixture) and by 52, 31, and 16% for values of λ > 1 (lean mixture). Overall, addition of anhydrous ethanol to the gasoline helped to reduce emissions of the pollutant gases investigated, what contributes to photochemical smog reduction and quality of life in urban areas.     

Single and combined effects of aluminum (Al<Subscript>2</Subscript>O<Subscript>3</Subscript>) and zinc (ZnO) oxide nanoparticles in a freshwater fish, <Emphasis Type="Italic">Carassius auratus</Emphasis>

The increasing use of nanoparticles (NPs) worldwide has raised some concerns about their impact on the environment. The aim of the study was to assess the toxicity of metal oxide nanoparticles, singly or combined, in a freshwater fish (Carassius auratus). The fish were exposed for 7, 14, and 21 days to different concentrations of NPs (10 μg Al₂O₃.L^?1, 10 μg ZnO.L^?1, 10 μg Al₂O₃.L^?1 plus 10 μg ZnO.L^?1, 100 μg Al₂O₃.L^?1, 100 μg ZnO.L^?1, and 100 μg Al₂O₃.L^?1 plus 100 μg ZnO.L^?1). At the end of each exposure period, antioxidant enzyme activity (catalase, glutathione-S-transferase, and superoxide dismutase), lipid peroxidation, and histopathology were assessed in the gills and livers of C. auratus. The results show an increase in catalase (CAT) and superoxide dismutase (SOD) activity in the gills and livers of fish, especially after 14 days of exposure to single and combined NPs, followed by a reduction at 21 days. An increase in glutathione S-transferase (GST) was observed in gills after 7 days for all tested NP concentrations (single and combined); while in livers, a significant increase was determined after 14 days of exposure to 100 μg.L^?1 of both single ZnO and Al₂O₃ NPs. Lipid peroxidation (LPO) significantly increased in gills after 7 days of exposure to 100 μg.L^?1 Al₂O₃ NPs (single or combined). In livers, LPO increased significantly after 7 days of exposure to all tested concentrations of both single ZnO and Al₂O₃ (except for 10 μg Al₂O₃.L^?1), and after 14 days of exposure to ZnO (10 and 100 μg.L^?1) and Al₂O₃ (100 μg.L^?1)_. The results from histological observations suggest that exposure to metal oxide NPs affected both livers and gills, presenting alterations such as gill hyperplasia and liver degeneration. However, the most pronounced effects were found in gills. In general, this study shows that the tested NPs, single or combined, are capable of causing sub-lethal effects on C. auratus, but when combined, NPs seem to be slightly more toxic than when added alone.     

Physiological and biochemical responses of <Emphasis Type="Italic">Machilus ichangensis</Emphasis> Rehd. et Wils and <Emphasis Type="Italic">Taxus chinensis</Emphasis> (Pilger) Rehd. to elevated O<Subscript>3</Subscript> in subtropical China

Considerable researches have documented the negative effects of ozone on woody species in North America and Europe; however, little is known about how woody tree species respond to elevated O₃ in subtropical China, and most of the previous studies were conducted using pot experiment. In the present study, Machilus ichangensis Rehd. et Wils (M. ichangensis) and Taxus chinensis (Pilger) Rehd. (T. chinensis), evergreen tree species in subtropical China, were exposed to non-filtered air (NF), 100 nmol mol^?1 O₃ (E1) and 150 nmol mol^?1 O₃ (E2), in open-top chambers under field conditions from 21st March to 2nd November 2015. In this study, O₃ fumigation significantly reduced net photosynthesis rate (Pn) in M. ichangensis in the three measurements and in T. chinensis in the last measurement. Also, non-stomatal factors should be primarily responsible for the decreased Pn. O₃ fumigation-induced increase in malondialdehyde, superoxide dismutase, and reduced ascorbic acid levels indicated that antioxidant defense mechanism had been stimulated to prevent O₃ stress and repair the oxidative damage. Yet, the increase of antioxidant ability was not enough to counteract the harm of O₃ fumigation. Because of the decrease in CO₂ assimilation, the growth of the two tree species was restrained ultimately. The sensitivity of the two tree species to O₃ can be determined: M. ichangensis > T. chinensis. It suggests a close link between the rising O₃ concentrations and the health risk of some tree species in subtropics in the near future.     

Conversion of Concentrated Solar Thermal Energy into Chemical Energy

When a concentrated solar beam is irradiated to the ceramics such as Ni-ferrite, the high-energy flux in the range of 1500–2500 kW/m² is absorbed by an excess Frenkel defect formation. This non-equilibrium state defect is generated not by heating at a low heating-rate (30 K/min), but by irradiating high flux energy of concentrated solar beam rapidly at a high heating rate (200 K/min). The defect can be spontaneously converted to chemical energy of a cation-excess spinel structure (reduced-oxide form) at the temperature around 1773 K. Thus, the O₂ releasing reaction (α-O₂ releasing reaction) proceeds in two-steps; (1) high flux energy of concentrated solar beam absorption by formation of the non-equilibrium Frenkel defect and (2) the O₂ gas formation from the O^2? in the Frenkel defect even in air atmosphere. The 2nd step proceeds without the solar radiation. We may say that the 1st step is light reaction, and 2nd step, dark reaction, just like in photosynthesis process.     

Impacts of boundary layer mixing on pollutant vertical profiles in the lower troposphere: Implications to satellite remote sensing

Mixing in the planetary boundary layer (PBL) affects vertical distributions of air tracers in the lower troposphere. An accurate representation of PBL mixing is critical for chemical-transport models (CTMs) for applications sensitive to simulations of the vertical profiles of tracers. The full mixing assumption in the widely used global CTM GEOS-Chem has recently been supplemented with a non-local PBL scheme. This study analyzes the impact of the non-local scheme on model representation of PBL mixing, consequences for simulations of vertical profiles of air tracers and surface air pollution, and implications for model applications to the interpretation of data retrieved from satellite remote sensing. The non-local scheme significantly improves simulations of the vertical distributions for NO₂ and O₃, as evaluated using aircraft measurements in summer 2004. It also reduces model biases over the U.S. by more than 10 ppb for surface ozone concentrations at night and by 2–5 ppb for peak ozone in the afternoon, as evaluated using ground observations. The application to inverse modeling of anthropogenic NO_x emissions for East China using satellite retrievals of NO₂ from OMI and GOME-2 suggests that the full mixing assumption results in 3–14% differences in top–down emission budgets as compared to the non-local scheme. The top–down estimate combining the non-local scheme and the Lin et al. inverse modeling approach suggests a magnitude of 6.6 TgN yr^?1 for emissions of NO_x over East China in July 2008 and 8.0 TgN yr^?1 for January 2009, with the magnitude and seasonality in good agreement with bottom–up estimates.     

Recent spatial gradients and time trends in Dhaka,Bangladesh, air pollution and their human health implications

Dhaka, the capital of Bangladesh, is among the most polluted cities in the world. This research evaluates seasonal patterns, day-of-week patterns, spatial gradients, and trends in PM_2.5 (<2.5 µm in aerodynamic diameter), PM₁₀ (<10 µm in aerodynamic diameter), and gaseous pollutants concentrations (SO₂, NO₂, CO, and O₃) monitored in Dhaka from 2013 to 2017. It expands on past work by considering multiple monitoring sites and air pollutants. Except for ozone, the average concentrations of these pollutants showed strong seasonal variation, with maximum during winter and minimum during monsoon, with the pollution concentration of PM_2.5 and PM₁₀ being roughly five- to sixfold higher during winter versus monsoon. Our comparisons of the pollutant concentrations with Bangladesh NAAQS and U.S. NAAQS limits analysis indicate particulate matter (PM_2.5 and PM₁₀) as the air pollutants of greatest concern, as they frequently exceeded the Bangladesh NAAQS and U.S. NAAQS, especially during nonmonsoon time. In contrast, gaseous pollutants reported far fewer exceedances throughout the study period. During the study period, the highest number of exceedances of NAAQS limits in Dhaka City (Darus-Salam site) were found for PM_2.5 (72% of total study days), followed by PM₁₀ (40% of total study days), O₃ (1.7% of total study days), SO₂ (0.38% of total study days), and CO (0.25% of total study days). The trend analyses results showed statistically significant positive slopes over time for SO₂ (5.6 ppb yr^?1, 95% confidence interval [CI]: 0.7, 10.5) and CO (0.32 ppm yr^?1, 95% CI: 0.01, 0.56), which suggest increase in brick kilns operation and high-sulfur diesel use. Though statistically nonsignificant annual decreasing slopes for PM_2.5 (?4.6 µg/m³ yr^?1, 95% CI: ?12.7, 3.6) and PM₁₀ (?2.7 µg/m³ yr^?1, 95% CI: ?7.9, 2.5) were observed during this study period, the PM_2.5 concentration is still too high (~ 82.0 µg/m³) and can cause severe impact on human health.

Implications: This study revealed key insights into air quality challenges across Dhaka, Bangladesh, indicating particulate matter (PM) as Dhaka’s most serious air pollutant threat to human health. The results of these analyses indicate that there is a need for immediate further investigations, and action based on those investigations, including the conduct local epidemiological PM exposure-human health effects studies for this city, in order to determine the most public health effective interventions.     

Heterogeneous Fenton degradation of bisphenol A catalyzed by efficient adsorptive Fe3O4/GO nanocomposites

A new method for the degradation of bisphenol A (BPA) in aqueous solution was developed. The oxidative degradation characteristics of BPA in a heterogeneous Fenton reaction catalyzed by Fe₃O₄/graphite oxide (GO) were studied. Transmission electron microscopic images showed that the Fe₃O₄ nanoparticles were evenly distributed and were ～6 nm in diameter. Experimental results suggested that BPA conversion was affected by several factors, such as the loading amount of Fe₃O₄/GO, pH, and initial H₂O₂ concentration. In the system with 1.0 g L^?1 of Fe₃O₄/GO and 20 mmol L^?1 of H₂O₂, almost 90 % of BPA (20 mg L^?1) was degraded within 6 h at pH 6.0. Based on the degradation products identified by GC–MS, the degradation pathways of BPA were proposed. In addition, the reused catalyst Fe₃O₄/GO still retained its catalytic activity after three cycles, indicating that Fe₃O₄/GO had good stability and reusability. These results demonstrated that the heterogeneous Fenton reaction catalyzed by Fe₃O₄/GO is a promising advanced oxidation technology for the treatment of wastewater containing BPA.     

Effect of Hydrocarbon and NO x on Photochemical Smog Formation under Simulated Transport Conditions

The body of information presented in this paper is directed to those individuals concerned with the effect of urban pollution on downwind areas. Concern has been expressed over the appropriate hydrocarbon and NO _x control strategy to be used in minimizing the effects of ozone and NO₂ on urban population centers and their downwind environs. O₃ and NO₂ formation were studied in smog chamber irradiations as a function of the initial NO _x concentration at three hydrocarbon concentrations. By carrying out the irradiations for a period of time equivalent to one solar day in a continuously diluting system, smog formation in a chemically reacting pollutant system under transport was simulated. The results of this experimental simulation suggest that hydrocarbon reduction reduces O₃ in urban as well as downwind areas while NO _x reduction increases O₃ in the urban area and has little effect on O₃ in downwind areas. Both hydrocarbon and NO _x reduction will reduce atmospheric NO₂ levels, with the effect of NO _x reduction generally being more pronounced.