废氨纶短纤维/废聚氨酯/丁腈橡胶复合材料的性能研究

对废氨纶短纤维/废聚氨酯(PU)/丁腈橡胶(NBR)复合材料的性能进行研究,探讨了废氨纶短纤维含量、废PU含量和两种低聚物对NBR胶复合材料的性能影响。结果表明,废氨纶短纤维含量在20份左右,材料的综合性能最佳;废PU能改善废氨纶短纤维/NBR胶的综合性能;两种低聚物均能明显改善复合材料的物理机械性能,酚醛树脂的改善效果较好。     

废混凝土粉在建筑砂浆中的应用研究

研究了废混凝土粉以不同取代率取代建筑砂浆中的天然砂对砂浆的和易性及强度的影响,结果表明,废混凝土粉可以取代建筑砂浆中的部分天然砂配制再生骨料砂浆.     

用废镍铝合金粉制备镍催化剂

研究了以废镍铝合金粉（废镍渣）为原料、H2SO4为浸出剂、尿素为沉淀剂制备镍催化剂的方法;考察了Ni浸出条件对其浸出率的影响,并通过催化加氢实验对镍催化剂的活性进行了评价。Ni的浸出条件：w（H2SO4）25％、酸浸时间3h、n（废镍渣）：n（H2SO4）=1．0：1．4。在该条件下,Ni的浸出率为92．85％。Ni的回收率在90％以上。催化加氢实验结果表明,在温度120～125℃、压力大于或等于1．2MPa、催化剂用量1％（质量分数）的条件下,可将异丙叉丙酮经一步液相催化加氢反应制备成甲基异丁基甲醇（MBC）,异丙叉丙酮转化率为100％,MIBC的收率达99．3％。     

风电行业废玻璃钢资源化处置研究

我国风电行业每年产生大量热固性玻璃钢废弃物,这些废弃的热固性复合材料叶片、机舱罩等,在处置过程中广泛存在资源浪费和环境污染问题。对风电行业废玻璃钢的来源、产生量进行分析,概述废玻璃钢的生态毒性,阐述当前玻璃钢废弃物资源化处置技术及其优缺点,并提出风电行业废玻璃钢资源化处置技术的未来发展方向。     

废粘土砖粉潜在活性探究

通过将磨细的废砖粉取代水泥制作胶砂试件,并测其抗折、抗压强度值来研究废砖粉的潜在活性,并在此基础上,进一步研究了石灰对废砖粉活性的激发作用.结果表明：磨细的废砖粉具有潜在活性,且粒径越小,活性越大;在一定掺量时,石灰可进一步激发废砖粉的活性.     

用微孔填充理论研究活性炭对有机气体的吸附性能

用微孔填充理论研究了活性炭C40／4对丙酮、甲苯、二氯甲烷有机气体的吸附性能,测试了该活性炭对3种有机气体在不同温度下（288．15,293．15,298．15K）的吸附结果。用D—R方程处理了实验数据,建立了3种有机气体在活性炭C40／4上的等温吸附模型,并将实验测试值与理论预测值进行了比较。实验结果表明：微孔填充理论及D—R方程可很好地描述活性炭C40／4对有机气体的吸附性能,理论预测值与实验测试值的平均相对误差小于3％;有机气体分压较高时,由于发生毛细凝聚,理论预测值较实验测试值偏低。     

废旧玻璃钢的回收利用

介绍了目前国内外热固性玻璃钢废弃物的回收利用方法,着重论述了化学热解回收法和物理粉碎回收法,对不同方法的回收料用于BMC和SMC的产品的性能进行了对比,分析了我国在玻璃钢回收方面的主要问题和发展方向.     

废陶瓷的表面改性及其吸附性能

以十八烷基三甲氧基硅烷为改性剂,对废陶瓷进行表面改性,使改性后的废陶瓷粒具有疏水性表而.考察了改性废陶瓷粒对工业废水的有机物去除作用以及对染料废水的脱色作用.实验结果表明,在改性废陶瓷粒径为1 -4 mm、改性废陶瓷加入量为500 g/L、吸附时间为30 min的条件下,造纸废水的COD去除率可达42％,亚甲基蓝溶液的...     

废电子焊料综合利用研究

针对电子产品焊接过程中产生的波峰焊渣、SMT过程中产生的废电子焊膏及废电子信息产品回收拆解过程中产生的废电子焊料的回收利用,开发经济实用的废电子焊料综合利用工艺技术与设备。在H2SiF6-Pb(Sn)SiF6电解液中,控制游离H2SiF6在100～150 g/L,Pb2(+Sn2+)在60～120 g/L,电流密度100 A/m2,槽电压0.3～0.5 V,常温电解,实现Pb-Sn合金的提纯精制,生产出合格的Pb-Sn合金焊料。然后用常规方法从电解阳极泥中进一步回收银等贵金属。     

废油漆桶无氧裂解工艺研究

废油漆桶的处理问题一直备受关注,目前常用的处置方法存在极大的环境风险,同时残留的油漆包含大量有机物,具有较高的回收利用价值.无氧裂解通过将有机废弃物转化成油、气、碳等,整个转化过程不会产生新的二次污染,具有较好的应用前景.对废油漆桶无氧裂解资源化过程进行探讨,研究反应温度及时间对油漆无氧裂解的影响,同时对反应产物进行分...     

Characterization of poly(lactic acid) biocomposites filled with chestnut shell waste

The aim of this study was to determine thermal and mechanical properties and applicability of ground chestnut shell waste as a filler for poly(lactic acid) composites. The used amount of filler was ranging from 2.5 to 30 wt%. Spectroscopic analysis of composites and its ingredients was conducted by means of FT-IR method. The mechanical and thermal properties of the composites were determined in the course of static tensile test, Dynstat impact strength test, DMTA analysis, and DSC method. The fractured surface morphology of biocomposites was evaluated by SEM analysis. Incorporation of the filler influenced the overall mechanical properties of the composites characterized by high stiffness and lowered impact resistance. Fabricated composites with different amounts of non-reactive natural waste filler exhibited acceptable mechanical and thermal properties. Therefore, these composites can be used as eco-friendly, biodegradable materials for low-demanding applications.     

废旧胶粉的制作及利用现状

简要介绍废旧胶粉的制造方法,以及胶粉在实际生产、生活当中的应用现状。提高废旧胶粉的再利用技术,拓展其应用领域,是节约资源、保护环境,促进国民经济增长方式转变和可持续发展的重要措施。     

Properties of alkali-activated systems with stone powder sludge

This article investigates the effects of stone powder sludge on the microstructure and strength development of alkali-activated fly ash and blast furnace slag mixes. Stone powder sludge produced from a crushed aggregate factory was used to replace fly ash and granulated blast furnace slag at replacement ratios of 0%, 10%, 20%, and 30% by mass. The unit weight and compressive strength of the samples were measured, and scanning electron microscopy/energy dispersive spectroscopy and X-ray diffraction (XRD) analyses were performed. The test results indicated that the compressive strength of alkali-activated blast furnace slag mixes using stone powder sludge was higher than that of the alkali-activated blast furnace slag control mix, but the compressive strength of alkali-activated fly ash mixes decreased with increasing replacement ratio of stone powder sludge. Microscopy results indicated that for alkaliactivated blast furnace slag samples, broken surfaces were more evident than for the alkali-activated fly ash samples. For all XRD diagrams, broad and diffuse peaks were observed around 2θ = 35° (d = 2.96–3.03 Å), implying amorphous or short-ordering structure phases.     

Mechanical and durability properties of insulation mortar with rubber powder from waste tires

Fine rubber particles from scrap tires can be used as an insulation material by incorporating with Portland cement mortar. In addition to thermal properties, there are special mechanical and durability properties that are important for the insulation mortar. The addition of rubber particles has negative impact on these properties. The special properties for insulation mortar can be improved using cellulose ether, redispersible polymer powder (RPP), and wood fiber. The objective of this study is to investigate the effects of these additives and the rubber powder on the properties of rubberized insulation mortar. With increasing rubber content, both flexural strength and compressive strength were reduced, but the reduction of flexural strength was not as significant as for the compressive strength. At a fixed rubber content, as the optimal amount of RPP and smaller rubber powder were used, the compressive strength of rubberized mortar satisfied the minimum requirement of the type N mortar. The drying shrinkage of the rubber mortar was about the same as the ordinary cement mortar. The permeability of the rubber mortar was low comparing with that of the ordinary cement mortar. The bond strength of the rubber mortar is low due to the reduced effective bonding surface.     

废旧天然胶胶粉应用研究

以80目的废天然胶胶粉为研究对象,处理后将其分别以20%,30%的比例添加到天然混炼胶(NR)中,制备废胶粉/NR共混硫化胶;同时,通过邻苯二甲酸酐(PA)和高芳烃油对胶粉进行处理改性,制备了全胶粉弹性体。拉伸强度测试表明,对于共混胶弹性体,NR混炼胶空白样的拉伸强度为19.21 MPa,添加20%,30%比例的胶粉/NR共混硫化胶的拉伸强度可以分别达到18.03 MPa,17.23 MPa;改性后制备的全胶粉混炼胶硫化样品拉伸强度达到8.12 MPa,超过了再生胶的国标标准。同时应用扫描电子显微镜SEM分析、比较了各试样断裂面的微观结构,应用比表面仪BET和SEM表征了胶粉的表面形貌与结构,发现胶粉表面呈现"绒球"状,具有较好的表面性能。     

我国废橡胶粉用于沥青改性的研究及应用

从道路建设与防水卷材制造两方面,描述了我国废橡胶粉在沥青改性用途中的研究及应用现状。大量国内试验及应用实例表明,与普通石油沥青相比,胶粉改性沥青的针入度、延度、软化点、温度敏感性、稳定性和抗老化性等性能均得到了改善。此外,较之其他种类的沥青改性剂,废橡胶粉成本低,具有环保与资源节约的优点,对我国循环经济的发展具有重要意义。     

Fly ash reinforced thermoplastic vulcanizates obtained from waste tire powder

Novel thermoplastic composites made from two major industrial and consumer wastes, fly ash and waste tire powder, have been developed. The effect of increasing fly ash loadings on performance characteristics such as tensile strength, thermal, dynamic mechanical and magnetic properties has been investigated. The morphology of the blends shows that fly ash particles have more affinity and adhesion towards the rubbery phase when compared to the plastic phase. The fracture surface of the composites shows extensive debonding of fly ash particles. Thermal analysis of the composites shows a progressive increase in activation energy with increase in fly ash loadings. Additionally, morphological studies of the ash residue after 90% thermal degradation shows extensive changes occurring in both the polymer and filler phases. The processing ability of the thermoplastics has been carried out in a Monsanto processability testing machine as a function of shear rate and temperature. Shear thinning behavior, typical of particulate polymer systems, has been observed irrespective of the testing temperatures. Magnetic properties and percolation behavior of the composites have also been evaluated.     

Characterization of the properties of thermoplastic elastomers containing waste rubber tire powder

The aim of this research was to recycle waste rubber tires by using powdering technology and treating the waste rubber tire powder with bitumen. It has been proven that the elongation at break, thermal stability and processing flowability of composites of polypropylene (PP), waste rubber tire powder (WRT) and bitumen composites are better than those of PP/WRT composite. A comparative study has been made to evaluate the influence of bitumen content and different compatibilizers on the properties of PP/WRT/bitumen composites, using a universal testing machine (UTM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and a capillary rheometer. The results suggested that the properties of PP/WRT/bitumen composites were dependent on the bitumen content and the kind of compatibilizer used.     

Recycling of waste biomass and mineral powder for preparation of potassium-enriched compost

An attempt was made to recycle waste biomass and mineral powder (waste mica) as an alternative source of potassium (K) through composting technology. Two different waste biomass, isabgol straw and palmarosa distillation waste along with two levels of waste mica (2 and 4% as K) were used for preparation of enriched composts. A notable decrease of C:N ratio was observed at the end of the composting (150 days) as an indicator of compost maturity. The mature composts were evaluated for K-supplying capacity through laboratory leaching and soil incubation study. Significantly higher water-soluble K released initially followed by a sharp decrease up to 21 days of leaching thereafter gradually decreased up to 35 days of leaching. Water-soluble K was released from K-enriched (mica charged) compost significantly higher than the ordinary compost throughout the leaching period. Soil incubation study also revealed that application of K-enriched compost greatly improved the available K (water soluble and exchangeable) pools in K-deficient soil which indicated that a considerable amount of K releases during composting. Therefore, K-enriched compost could be an effective alternative of costly commercial K fertilizer and eco-friendly approach to utilize low-cost waste mineral powder and plant residue.