氢化物诱致金属稳态裂纹扩展数学模型的应用

在温度和裂尖速度恒定、平面应变和小规模屈服、小规模氢化物沉淀条件下,应用有限元法研究氢化物诱致金属稳态裂纹扩展的信息.在考虑氢扩散、氢化物沉淀、非机械能量流和氢化物/固溶变形等多物理的耦合现象条件下,有限元结果和导出的分析表达式给出的结果都证实应力平稳平台的存在,且两种计算结果相当一致.分析关系式基于氢化学平衡并明确表明了温度、远端氢浓度和氢化物弹性性态效应.裂纹尖端场特性用于发展断裂准则和估计应力强度因子阈值.当归一化应力强度因子趋于零时,临近应力强度因子阈值的裂尖场产生,表现为氢化物沉淀区出现常静水应力.随着归一化应力强度因子值增加,裂纹扩展裂尖场从阶段I演化到阶段II,氢化物沉淀区域实际尺寸减小并偏离平台水平,裂尖场附近的力学响应基本和金属中不含有氢的工况一致,此时裂尖场强烈依赖于远离裂尖场的氢浓度.     

连续管复合裂纹的应力强度因子有限元分析

针对解析法计算连续管复合裂纹应力强度因子繁琐的问题,引入扩展有限元法（XFEM）进行分析。应用有限元软件ABAQUS计算不同裂纹角度对应的连续管Ⅰ,Ⅱ,Ⅲ型裂纹的裂尖应力强度因子KⅠ,KⅡ,KⅢ,分析了裂纹角度对应力强度因子的影响,并模拟得到了受单向拉伸载荷的连续管裂纹扩展的整个过程。研究结果表明:扩展有限元解与计算解很接近,验证了利用扩展有限元法计算复合型应力强度因子的有效性。随着裂纹夹角θ的增大,裂尖处KⅠ不断减小、KⅡ始终很小,可以忽略、KⅢ先增大后减小、总应力强度因子K不断减小。通过扩展有限元法计算出裂尖应力强度因子,可有效预测含裂纹CT80连续管的安全性。     

含半无限长裂纹压电材料的Ⅲ型强度因子

研究了含半无限长裂纹压电材料在平面内电场和反平面荷载作用下的问题 ,得到了满足拉普拉斯方程、裂纹面边界条件的位移函数解和电势函数解及电弹场的基本解 ,并得到了应力、应变、电位移强度因子和能量释放率。研究结果表明 ,在裂尖 ,电场强度没有奇异性 ,而应变、应力、电位移具有奇异性。     

煤层底板卸荷扰动断裂机制宏细观研究

基于断裂力学和重整化群理论,采用综合研究方法,从宏细观角度对开采扰动底板损伤岩层动态失稳机理进行了研究。结果表明,煤层回采后,底板岩层存在高应力束组成的主应力拱,最大主应力大小决定裂纹的起裂与扩展,裂纹的生长路径受控于最大主应力的方向。采场高支承压力引起岩层原始裂纹起裂,宏观上表现为底板岩层的预先剪切随机破坏;近场区域最大主应力场部分偏转,引起底板岩层中垂直应力显著降低、浅部水平应力急剧增加和斜向采空区方向产生高剪应力,迫使裂隙在原有扩展长度基础上进一步生长;工作面继续推进,采空区内底板岩层水平方向上压缩和竖向膨胀引起岩层拉破坏,当底板岩层损伤发展到临近损伤值时,极小范围的扰动被强烈放大,底板岩层由随机破坏转为"雪崩"式宏观断裂。     

断裂力学及其在岩石中的应用

第二讲应力强度因子 1.裂纹尖端的应力强度因子在第一讲中已经指出,如果载荷对称于裂纹平面,并使裂纹受拉,则这样的裂纹叫     

海底悬跨管道表面双裂纹数值分析

为了研究海底油气管道多个裂纹间相互作用对管道产生的影响,针对海底悬跨管道表面双裂纹的相互作用,采用有限元方法建立双环向表面裂纹模型,采用围道积分法求解双裂纹下的应力强度因子,研究了不同边界条件下,不同尺寸裂纹间的相互影响规律,并对比了单裂纹下应力强度因子的变化情况。研究结果表明:不同尺寸的裂纹对双裂纹的相互影响规律有一定影响,且双裂纹应力强度因子最大值均出现在裂纹最深点处;弹簧边界下双裂纹相互影响规律与简单边界下相互影响规律明显不同;不同边界条件对悬跨管道双裂纹应力强度因子的影响较大。研究结果可为海底悬跨管道的失效分析提供参考依据。     

超高强度钻杆低温断裂性能及裂纹扩展特征研究

超高强度钻杆在冬季低温环境下容易发生脆性断裂事故,为了从断裂力学角度揭示其冷脆现象的本质,采用ZBC2302-D型示波冲击试验机,获得了不同温度下超高强度钢在冲击断裂过程中的力-位移曲线,并对比分析了冲击功、起裂功和裂纹扩展功之间的变化关系。采用国家标准GB 4161—2007中的计算公式,计算了冲击试样的裂纹扩展量Δa和阻抗应力强度因子K_R;同时,引入K_R阻力曲线,得到超高强度钻杆在不同温度下的剩余强度图。结果表明,当冲击试样开始出现裂纹时,随温度降低,钻杆的初始起裂应力有所增加,出现硬化现象。当钻杆出现一定长度的裂纹时,随温度降低,阻抗应力强度因子越来越小,而且降低速度越来越快,剩余强度也表现出相同的变化趋势。随温度降低,材料抵抗裂纹扩展的能力逐渐下降,表明钻杆在低温下更容易断裂。     

车用CNG2气瓶金属内胆低周疲劳行为分析

在对CNG2气瓶进行有限元分析的基础上,对应变集中区域的应力进行了分析。运用Manson-Coffin公式,结合气瓶内胆的应变疲劳性能计算得到疲劳寿命,计算结果与气瓶疲劳试验寿命相符。制造过程中使用预紧工艺或过载方式产生塑性变形和残余压应力,可以提高应力强度范围门槛值,使裂纹启裂减慢,从而延长了气瓶的疲劳寿命。     

环向缠绕气瓶金属内胆表面裂纹的应力强度因子计算

本文利用弹塑性理论对环向缠绕气瓶自紧及服役工况进行应力分析,推导得出不同工况下,气瓶的复合材料和内胆的应力、应变计算公式,并展开讨论。以金属内胆应力计算公式为基础,借鉴平板椭圆形表面裂纹应力强度因子公式,给出了金属内胆表面椭圆形裂纹应力强度因子的计算方法。通过算例表明,内胆裂纹的应力强度因子除与裂纹几何参量、气瓶内压相关,还与气瓶制造时自紧工艺相关,同一气瓶设计,最小、最大自紧引起的应力强度因子相差36%。     

球罐裂纹与焊接接头表面涂层改性防护

介绍16MnR钢制液化石油气球罐开罐检验内表面焊接接头经常发现裂纹的概况,分析硫化氢应力腐蚀裂纹本质上属焊接接头氢致裂纹,指出通过给内表面焊接接头进行铝涂层改性防护,可避免液化石油气球罐产生裂纹从而创造巨大的社会效益和经济效益.     

油浸变压器排油注氮装置在500kV变电站的设计与应用

在分析500kV变电站主变压器消防系统的现状,比较3类消防系统优缺点的基础上,详细论述了主变排油注氮装置的结构组成、工作原理、参数计算、控制系统设计以及需要注意的事项等,为下一步排油注氮装置的推广应用打下基础.     

HAZOP结合What-if方法在某延迟焦化装置除焦中的应用

为克服传统危险与可操作性（HAZOP）定性分析方法在复杂操作、间歇作业等过程中使用的局限性,提出在传统HAZOP定性分析方法的基础上结合What-if（故障假设）方法,对人的不安全行为和操作规程不完备所导致的风险后果分析作出补充。详细说明其技术原理、工作流程等使用细节,系统阐述该方法与传统HAZOP定性分析方法的区别,并在某延迟焦化装置的除焦操作的风险分析中应用。经分析,识别出在“给水-泡焦”节点,有“操作规程错误”场景2项,“操作规程不具体”场景1项,不存在“操作人员未按操作规程执行”场景。研究结果表明:本文方法有效且具有较好效果,可以广泛应用于操作规程/作业指导书审查、作业过程隐患排查等方面,帮助企业开展操作层面的风险识别与管理,提升企业的生产安全水平。     

Nighttime pedestrian fatalities: A comprehensive examination of infrastructure,user, vehicle,and situational factors

Introduction: Pedestrian fatalities in the United States increased 45.5% between 2009 and 2017. More than 85% of those additional pedestrian fatalities occurred at night. Method: We examine Fatality Analysis Reporting System (FARS) data for fatal pedestrian crashes that occurred in the dark between 2002 and 2017. Within-variable and before/after examinations of crashes in terms of infrastructure, user, vehicle, and situational characteristics are performed with one-way analysis of variance (ANOVA) and two-sample t-tests. We model changes in crash characteristic proportions between 2002–2009 and 2010–2017 using linear regressions and test for autocorrelation with Breusch-Godfrey tests. Results: The increase in fatal nighttime pedestrian crashes is most strongly correlated with infrastructure factors: non-intersection unmarked locations (saw 80.8% of additional fatalities); 40–45 mph roads (54.6%); five-lane roads (40.7%); urban (99.7%); and arterials (81.1%). In addition, SUVs were involved in 39.7% of additional fatalities, overrepresenting their share of the fleet. Increased pedestrian alcohol and drug involvement warrant further investigation. The age of pedestrians killed increased more (18.1%) than the national average (3.2%). Conclusions: By identifying factors related to the increase in nighttime pedestrian fatalities, this work constitutes a vital first step in making our streets safer for pedestrians. Practical Applications: More research is needed to understand the efficacy of different solutions, but this paper provides guidance for such future research. Engineering solutions such as road diets or traffic calming may be used to improve identified infrastructure issues by reducing vehicle speeds and road widths. Rethinking vehicle design, especially high front profiles, may improve vehicle issues. However, the problems giving rise to these pedestrian fatalities are likely a result of not only engineering issues but also interrelated social and political factors. Solutions may be correspondingly comprehensive, employing non-linear, systems-based approaches such as Safe Systems.     

潞安矿区煤层渗透率的各向异性特征实验研究

为了研究原位煤体渗透性的各向异性特征,以山西潞安常村矿3号煤层圆柱试样为对象,利用TCQT-Ⅲ型低渗煤层气相驱替增产试验装置,对煤样进行加载,并以氮气注入压力2.0 MPa的条件下,分析垂直层理和平行层理2个方向的煤体变形和渗透率变化特征。实验结果表明:煤样在加载过程中,平行和垂直层理煤样渗透率均随着有效应力的增大而减小,平行层理方向的渗透率始终大于垂直层理方向,应力加载初期渗透率急剧下降,最后逐渐趋于平缓;径向应变的增加量与渗透率呈正相关性,且平行层理相关性大于垂直层理;沿平行层理方向的裂隙度大于沿垂直层理方向,沿垂直层理方向的应变量大于沿平行层理方向;应变增加量均随有效应力的增加而逐渐减小。研究结果可为煤层井网布置及优化提供参考。     

森林地表火蔓延模拟方法及其计算机实现

进行了森林火蔓延的研究,对传统的经验公式和模型进行改进,明显发现改进的模型有更好的结果,用计算机巧妙准确地实现了模拟模型,在风力不是特别大,地形变化不是特别剧烈时,该模型有较高精度;并结合火蔓延的主要因素（气象因子、气候、地形等）,进行系统分析,写出算地,编制实现地表火蔓延的预测预报计算机系统软件。这对于有效的组织扑救、减少火灾损失、计算森林火灾的损失评估有重要意义。     

Footedness and Mounting—Short Review and Two Case Studies

Footedness is a personal quality like handedness. Footedness may be associated with moving ability during mounting, dismounting, and jumping movements. Occupational accidents have occurred during movement at different working levels, during the use of access and exit systems, and during the mounting of vehicles. Aging can also affect accident risk and body laterality. For example, falling accidents on stairs are common among the elderly. One reason for accidents may be that the structure of the access system or stair system is unsuitable for individual moving patterns depending partly on body laterality. Footedness and the way the feet are used may be contradictory to the demands of the moving situation, especially during uncommon or rapid situations. This contradiction may trigger disturbance during moving. The aims of this pilot study were (a) to review the literature briefly and (b) to describe the use of the dominant and nondominant foot by farmers and the elderly when mounting a tractor and stairs, respectively. The study also gives ideas for future studies based on both (a) and (b).     

AHP与GA-SVM耦合模型在滑坡预警中的应用*

为了减少滑坡造成的损失,提高滑坡预测的准确性,通过搭建灾害模拟平台获得滑坡的实验数据,在获得多组模拟实验数据后,分析各变量的特性。首先,通过层次分析(Analytic Hierarchy Process,AHP)算法,对滑坡进行危险度划分;然后,通过支持向量机(Support Vector Machine,SVM)建立模型,遗传算法(Genetic Algorithm,GA)再优化SVM参数,提出1种层次分析法与GA-SVM相耦合的模型。研究结果表明:AHP方法划分后的数据,通过GA与SVM结合建立的模型精度较好,实验预测结果与实际结果较为吻合,与单一SVM相比,精度更高,结果更好,更加适用于多变量的复杂非线性滑坡预警。     

Debunking the false dichotomy of leadership idealism and pragmatism: Critical evaluation and support of newer genre leadership theories

Leadership theories have shifted over the last few decades from a focus on managerial functions and economic leader–follower exchanges toward greater focus on the interpersonal dynamics occurring within the leadership process. Theories such as transformational, ethical, authentic, and other “newer genre” theories were created to address neglected topics such as leader vision and inspirational messages, transparency, emotional effects, morality, individualized attention, and intellectual stimulation. Critiques of these theories, however, have been raised. In this paper, we address five of those critiques and argue for the validity and practical effectiveness of the new genre theories. Further, we describe how newer genre leadership research should be viewed as a performative epistemology, entailing a process of co‐creation involving scholars and practitioners. Finally, from this view, we provide general ideas for leader development. Copyright © 2014 John Wiley & Sons, Ltd.     

Occupational Safety and Health in Finland

In Finland, occupational safety is the responsibility of the employer, while the occupational safety and health laws are enforced by the Labour Inspection Service, an organization of the state. The Labour Inspection is divided in 11 administrative districts, and it employs 360 professionals. They are mandated to carry out site visits without prearranged appointments to inspect safe work situations, working hours, construction safety, or any aspect of accident risks. The inspectors are also mandated to verify the existence of sufficient occupational health services as prescribed by the Occupational Health Services Act for all employees. The occupational health services are typically provided by enterprise-owned medical departments, by mutually owned health care centers, by private practitioners, or by municipal health care centers. The latter are required by law to provide all services as prescribed by the legislation to anyone who comes to the facility. This situation is prevalent in the countryside, where there are very few private caregiving centers. Declaring occupational accidents and disease cases is mandatory, and the Inspection districts examine all accidents to establish causes and consequences, and to initiate prosecution in case of criminal negligence. Labour Inspection Districts are also notified of the new occupational disease cases as they are declared to insurance companies. Insurance for occupational disease, accidents, and death is an obligation of the employer, although they can choose the insurance company. The medical confidentiality between the workers and their occupational health care providers is very strict. Official statistics are maintained by the state Statistics Finland organization, and they may be used, for example, for research purposes by scientific institutes like the Finnish Institute of Occupational Health. Construction industry accounts for 25% of all fatal accidents (120 cases per 1 million working hours), followed by mechanical, wood, metal, machinery, and pulp and paper industry (10% each of fatal accidents) with rates ranging from 100–160 cases per 1 million working hours. There are some 5,000 occupational disease cases per year (rate 22/10,000 employed). The major disease categories include repetitive strain injuries (1,300 cases), respiratory allergies (600 cases), occupational skin diseases (1,000 cases), and 900 cases of noise-caused hearing loss. In 1998, 589 cases of asbestos-related diseases were reported.     

公路隧道火灾逃生疏散研究

以苍岭隧道为背景,首先采用经验计算理论和计算软件building EXODUS相结合的方式,从被困人员的安全疏散时间、高温烟气的影响、隧道横通道的利用率以及人员的疏散行为特性进行了研究。结果表明:中小规模火灾情况下的安全疏散时间控制在8 min之内,高温烟气影响不大,但横通道的利用率不平均,且人员疏散路线相对集中。然后对存在的逃生疏散问题提出针对性建议以及其他相关建议,旨在为更大程度降低事故的严重性和经济财产损失。