Sequestration of toxic Pb(Ⅱ) ions by chemically treated rubber(Hevea brasiliensis) leaf powder

Rubber leaf powder(an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(Ⅱ) ions from aqueous solution was evaluated.The interactions between Pb(Ⅱ) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared(FT-IR) spectroscopy,scanning electron microscopy(SEM) coupled with X-ray energy dispersive spectroscopy(EDX).The effects of several important parameters which can affect adsorption capacity such as pH,adsorbent dosage,initial lead concentration and contact time were studied.The optimum pH range for lead adsorption was 4-5.Even at very low adsorbent dosage of 0.02 g,almost 100% of Pb(Ⅱ) ions(23 mg/L) could be removed.The adsorption capacity was also dependent on lead concentration and contact time,and relatively a short period of time(60-90 min) was required to reach equilibrium.The equilibrium data were analyzed with Langmuir,Freundlich and Dubinin-Radushkevich isotherms.Based on Langmuir model,the maximum adsorption capacity of lead was 95.3 mg/g.Three kinetic models including pseudo first-order,pseudo second-order and Boyd were used to analyze the lead adsorption process,and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

Sequestration of toxic Pb（II） ions by chemically treated rubber （Hevea brasiliensis ） leaf powder

Rubber leaf powder (an agricultural waste) was treated with potassium permanganate followed by sodium carbonate and its performance in the removal of Pb(II) ions from aqueous solution was evaluated. The interactions between Pb(II) ions and functional groups on the adsorbent surface were confirmed by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) coupled with X-ray energy dispersive spectroscopy (EDX). The effects of several important parameters which can affect adsorption capacity such as pH, adsorbent dosage, initial lead concentration and contact time were studied. The optimum pH range for lead adsorption was 4–5. Even at very low adsorbent dosage of 0.02 g, almost 100% of Pb(II) ions (23 mg/L) could be removed. The adsorption capacity was also dependent on lead concentration and contact time, and relatively a short period of time (60–90 min) was required to reach equilibrium. The equilibrium data were analyzed with Langmuir, Freundlich and Dubinin-Radushkevich isotherms. Based on Langmuir model, the maximum adsorption capacity of lead was 95.3 mg/g. Three kinetic models including pseudo first-order, pseudo second-order and Boyd were used to analyze the lead adsorption process, and the results showed that the pseudo second-order fitted well with correlation coefficients greater than 0.99.     

Removal of Methyl Violet from aqueous solutions using poly （acrylic acid.co-acrylamide）/attapulgite composite

The adsorption of Methyl Violet (MV) cationic dye from aqueous solution was carried out by using crosslinked poly (acrylic acid-co-acrylamide)/attapulgite (Poly(AA-co-AM)/ATP) composite as adsorbent. The factors influencing adsorption capacity of the composite such as pH, concentration of the dye, temperature, contact time, adsorbent dosage, ionic strength and surfactant were systematically investigated. The equilibrium data fitted very well to the Langmuir isotherm and the maximum adsorption capacity reached 1194 mg/g at 30°C. The thermodynamic parameters including G0, △H0 and △S 0 for the adsorption processes of MV on the composite were also calculated, and the negative △H0 and △G0 confirmed that the adsorption process was exothermic and spontaneous. The kinetic studies showed that the adsorption process was consistent with the pseudo second-order kinetic model and the desorption studies revealed that the regeneration of the composite adsorbent can be easily achieved.     

Kinetic adsorption of application of carbon nanotubes for Pb(Ⅱ) removal from aqueous solution

The capability of carbon nanotubes (CNTs) to adsorb lead (Pb) in aqueous solution was investigated. Batch mode adsorption experiment was conducted to determine the effects of pH, agitation speed, CNTs dosage and contact time. The removal of Pb(Ⅱ) reached maximum value 85% or 83% at pH 5 or 40 mg/L of CNTs, respectively. Higher correlation coeffcients from Langmuir isotherm model indicates the strong adsorptions of Pb(Ⅱ) on the surface of CNTs (adsorption capacity Xm = 102.04 mg/g). The results indicates tha...     

Ethyl thiosemicarbazide intercalated organophilic calcined hydrotalcite as a potential sorbent for the removal of uranium(VI) and thorium(IV) ions from aqueous solutions

This work was conducted to determine the practicability of using a new adsorbent 4-ethyl thiosemicarbazide intercalated,organophilic calcined hydrotalcite(ETSC-OHTC) for the removal of uranium(U(VI)),and thorium(Th(IV)) from water and wastewater.The FTIR analysis helped in realizing the involvement of nitrogen and sulphur atoms of ETSC in binding the metal ions through complex formation.Parameters like adsorbent dosage,solution pH,initial metal ions concentration,contact time and ionic strength,that influence adsorption phenomenon,were studied.The optimum pH for maximum adsorption of U(VI) and Th(IV) was found to be in the range 4.0-6.0.The contact time required for reaching equilibrium was 4 hr.The pseudo second-order kinetic model was the best fit to represent the kinetic data.Analysis of the equilibrium adsorption data using Langmuir,Freundlich and Sips models showed that the Freundlich model was well suited to describe the metal ions adsorption.The K F values were 25.43 and 29.11mg/g for U(VI) and Th(IV),respectively,at 30°C.The adsorbent can be regenerated effectively from U(VI) and Th(IV) loaded ones using 0.01mol/L HCl.The new adsorbent was quite stable for many cycles,without much reduction in its adsorption capacity towards the metals.     

Removal of Pb(Ⅱ) from aqueous solutions using waste textiles/poly(acrylic acid) composite synthesized by radical polymerization technique

Waste textiles(WTs) are the inevitable outcome of human activity and should be separated and recycled in view of sustainable development. In this work, WT was modified through grafting with acrylic acid(AA) via radical polymerization process using ceric ammonium nitrate(CAN) as an initiator and microwave and/or UV irradiation as energy supply. The acrylic acid-grafted waste textiles(WT-g-AA) thus obtained was then used as an adsorbent to remove Pb(Ⅱ) from Pb(Ⅱ)-containing wastewater. The effects of p H, initial concentrations of Pb(Ⅱ) and adsorbent dose were investigated, and around 95% Pb(Ⅱ) can be removed from the aqueous solution containing 10 mg/L at p H 6.0–8.0. The experimental adsorption isotherm data was fitted to the Langmuir model with maximum adsorption capacity of35.7 mg Pb/g WT-g-AA. The Pb-absorbed WT-g-AA was stripped using dilute nitric acid solution and the adsorption capacity of Pb-free material decreased from 95.4%(cycle 1) to91.1%(cycle 3). It was considered that the WT-g-AA adsorption for Pb(Ⅱ) may be realized through the ion-exchange mechanism between \COOH and Pb(Ⅱ). The promising results manifested that WT-g-AA powder was an efficient, eco-friendly and reusable adsorbent for the removal of Pb(Ⅱ) from wastewater.     

Pb(Ⅱ) biosorption using chitosan and chitosan derivatives beads: Equilibrium,ion exchange and mechanism studies

The study examined the adsorption of Pb(II) ions from aqueous solution onto chitosan, chitosan-GLA and chitosan-alginate beads. Several important parameters influencing the adsorption of Pb(II) ions such as initial pH, adsorbent dosage and different initial concentration of Pb(II) ions were evaluated. The mechanism involved during the adsorption process was explored based on ion exchange study and using spectroscopic techniques. The adsorption capacities obtained based on non-linear Langmuir isotherm for ch...     

Removal of Pb(II) from aqueous solution by hydrous manganese dioxide: Adsorption behavior and mechanism

Hydrous manganese dioxide (HMO) synthesized by redox of potassium permanganate and hydrogen peroxide was used as an adsorbent for Pb(Ⅱ) removal.The specific surface area,pore volume and BJH pore diameter of the HMO were 79.31m2/g,0.07cm3/g and 3.38 nm,respectively.The adsorption equilibrium at 298K could be well described by the Langmuir isotherm equation with q max value of 352.55mg/g.The negative values of G and the positive values of H and S indicated the adsorption process was spontaneous and endothermic.The pseudo second-order equation could best fit the adsorption data.The value of the calculated activation energy for Pb(Ⅱ) adsorption onto the HMO was 38.23 kJ/mol.The uptake of Pb(Ⅱ) by HMO was correlated with increasing surface hydroxyl group content and the main adsorbed speciation was PbOH+.The final chemical state of Pb(Ⅱ) on the surface of HMO was similar to PbO.HMO was a promising candidate for Pb(Ⅱ) removal from aqueous solution.     

Adsorption of Disperse Blue SBL dye by synthesized poorly crystalline hydroxyapatite

The present study has been undertaken to evaluate the adsorption in batch mode of a disperse dye (Disperse Blue SBL) by poorly crystalline hydroxyapatite synthesized by coprecipitation between Ca(NO_3)_2 and (NH_4)_2HPO4 reagents in aqueous solution at room temperature. The adsorption experiments were carried out to investigate the factors that influence the dye uptake by the adsorbent, such as the contact time under agitation, adsorbent dosage, initial dye concentration, solution temperature, and pH. The e...     

Removal of ammonium ion from water by Na-rich birnessite: Performance and mechanisms

Na-rich birnessite (NRB) was synthesized by a simple synthesis method and used as a high-efficiency adsorbent for the removal of ammonium ion (NH₄⁺) from aqueous solution. In order to demonstrate the adsorption performance of the synthesized material, the effects of contact time, pH, initial ammonium ion concentration, and temperature were investigated. Adsorption kinetics showed that the adsorption behavior followed the pseudo second-order kinetic model. The equilibrium adsorption data were fitted to Langmuir and Freundlich adsorption models and the model parameters were evaluated. The monolayer adsorption capacity of the adsorbent, as obtained from the Langmuir isotherm, was 22.61 mg NH₄⁺-N/g at 283 K. Thermodynamic analyses showed that the adsorption was spontaneous and that it was also a physisorption process. Our data revealed that the higher NH₄⁺ adsorption capacity could be primarily attributed to the water absorption process and electrostatic interaction. Particularly, the high surface hydroxyl-content of NRB enables strong interactions with ammonium ion. The results obtained in this study illustrate that the NRB is expected to be an effective and economically viable adsorbent for ammonium ion removal from aqueous system.     

Using a novel adsorbent macrocyclic compound cucurbit[8]uril for Pb removal from aqueous solution

In this study, cucurbit[8]uril (CB[8]) was utilized as a kind of new adsorbent to remove Pb^2 + ions from aqueous solution. With the solution pH increased from 2 to 6, the removal efficiency of adsorption increased from 55.6% to 74.5%correspondingly. The uptake of Pb^2 + increased rapidly in the initial 30 min, and then the adsorption rate became slower. The Pseudo-second order model could be used to interpret the adsorption kinetics satisfactorily; and the rate determining step in Pb^2 + adsorption onto CB[8] was the external mass transfer step. Equilibrium isotherm study reveals that the Langmuir model gave a better fitting result than Freundlich model. The maximum adsorption capacity calculated by the Langmuir model was 152.67 mg/g for 298 K, 149.70 mg/g for 313 K and 136.42 mg/g for 323 K, respectively. The adsorption is a spontaneous process of exothermic nature. The effect of the adsorbent dosage and the influences of solution pH and co-existing cations were also investigated. The CB[8] was synthesized and characterized by ¹H NMR, IR, ESI-MS spectra, SEM-EDAX, Zeta-potential and BET-analysis. The adsorption mechanism was due to the coordination between CB[8] molecule and Pb^2 + ions.     

Synthesis, characterization and application of Lagerstroemia speciosa embedded magnetic nanoparticle for Cr(VI) adsorption from aqueous solution

Lagerstroemia speciosa bark (LB) embedded magnetic nanoparticles were prepared by co-precipitation of Fe²⁺ and Fe³⁺ salt solution with ammonia and LB for Cr(VI) removal from aqueous solution. The native LB, magnetic nanoparticle (MNP), L. speciosa embedded magnetic nanoparticle (MNPLB) and Cr(VI) adsorbed MNPLB particles were characterized by SEM–EDX, TEM, BET-surface area, FT-IR, XRD and TGA methods. TEM analysis confirmed nearly spherical shape of MNP with an average diameter of 8.76 nm and the surface modification did not result in the phase change of MNP as established by XRD analysis, while led to the formation of secondary particles of MNPLB with diameter of 18.54 nm. Characterization results revealed covalent binding between the hydroxyl group of MNP and carboxyl group of LB particles and further confirmed its physico-chemical nature favorable for Cr(VI) adsorption. The Cr(VI) adsorption on to MNPLB particle as an adsorbent was tested under different contact time, initial Cr(VI) concentration, adsorbent dose, initial pH, temperature and agitation speed. The results of the equilibrium and kinetics of adsorption were well described by Langmuir isotherm and pseudo-second-order model, respectively. The thermodynamic parameters suggest spontaneous and endothermic nature of Cr(VI) adsorption onto MNPLB. The maximum adsorption capacity for MNPLB was calculated to be 434.78 mg/g and these particles even after Cr(VI) adsorption were collected effortlessly from the aqueous solution by a magnet. The desorption of Cr(VI)-adsorbed MNPLB was found to be more than 93.72% with spent MNPLB depicting eleven successive adsorption–desorption cycles.     

Pb（II） biosorption using chitosan and chitosan derivatives beads： Equilibrium, ion exchange and mechanism studies

The study examined the adsorption of Pb(II) ions from aqueous solution onto chitosan, chitosan-GLA and chitosan-alginate beads. Several important parameters influencing the adsorption of Pb(II) ions such as initial pH, adsorbent dosage and di erent initial concentration of Pb(II) ions were evaluated. The mechanism involved during the adsorption process was explored based on ion exchange study and using spectroscopic techniques. The adsorption capacities obtained based on non–linear Langmuir isotherm for chitosan, chitosan-GLA and chitosan-alginate beads in single metal system were 34.98, 14.24 and 60.27 mg/g, respectively. However, the adsorption capacity of Pb(II) ions were reduced in the binary metal system due to the competitive adsorption between Pb(II) and Cu(II) ions. Based on the ion exchange study, the release of Ca2+, Mg2+, K+ and Na+ ions played an important role in the adsorption of Pb(II) ions by all three adsorbents but only at lower concentrations of Pb(II) ions. Infrared spectra showed that the binding between Pb(II) ions and the adsorbents involved mostly the nitrogen and oxygen atoms. All three adsorbents showed satisfactory adsorption capacities and can be considered as an e cient adsorbent for the removal of Pb(II) ions from aqueous solutions.     

Adsorptive removal of heavy metal ions from industrial effluents using activated carbon derived from waste coconut buttons

Removal of heavy metal ions from industrial effluents by the activated carbon prepared by steam activation of waste coconut buttons through batch adsorption process.     

From illite/smectite clay to mesoporous silicate adsorbent for efficient removal of chlortetracycline from water

A series of mesoporous silicate adsorbents with superior adsorption performance for hazardous chlortetracycline(CTC) were sucessfully prepared via a facile one-pot hydrothermal reaction using low-cost illite/smectite(IS) clay,sodium silicate and magnesium sulfate as the starting materials.In this process,IS clay was "teared up" and then "rebuilt" as new porous silicate adsorbent with high specific surface area of 363.52 m~2/g(about 8.7 folds higher than that of IS clay) and very negative Zeta potential(- 34.5 mV).The inert Si- O- Si(Mg,Al) bonds in crystal framework of IS were broken to form Si(Al)- O~- groups with good adsorption activity,which greatly increased the adsorption sites served for holding much CTC molecules.Systematic evaluation on adsorption properties reveals the optimal silicate adsorbent can adsorb 408.81 mg/g of CTC(only 159.7 mg/g for raw IS clay) and remove 99.3%(only 46.5%for raw IS clay) of CTC from 100 mg/L initial solution(pH 3.51;adsorption temperature 30℃;adsorbent dosage,3 g/L).The adsorption behaviors of CTC onto the adsorbent follows the Langmuir isotherm model,Temkin equation and pseudo second-order kinetic model.The mesopore adsorption,electrostatic attraction and chemical association mainly contribute to the enhanced adsorption properties.As a whole,the high-efficient silicate adsorbent could be candidates to remove CTC from the wastewater with high amounts of CTC.     

Pb(II) removal from water using Fe-coated bamboo charcoal with the assistance of microwaves

Bamboo charcoal(BC) was used as starting material to prepare iron-modified bamboo charcoal(Fe-MBC) by its impregnation in FeCl 3 and HNO 3 solutions simultaneously,followed by microwave heating.The material can be used as an adsorbent for Pb(Ⅱ) contaminants removal in water.The composites were prepared with Fe molar concentration of 0.5,1.0 and 2.0 mol/L and characterized by means of N 2 adsorption-desorption isotherms,X-ray diffraction spectroscopy(XRD),scanning electron microscopy coupled with energy dispersive X-ray spectrometry(SEM-EDS),Fourier transform infrared(FT-IR) and point of zero charge(pH pzc) measurements.Nitrogen adsorption analyses showed that the BET specific surface area and total pore volume increased with iron impregnation.The adsorbent with Fe molar concentration of 2 mol/L(2Fe-MBC) exhibited the highest surface area and produced the best pore structure.The Pb(Ⅱ) adsorption process of 2Fe-MBC and BC were evaluated in batch experiments and 2Fe-MBC showed an excellent adsorption capability for removal Pb(Ⅱ).The adsorption of Pb(Ⅱ) strongly depended on solution pH,with maximum values at pH 5.0.The ionic strength had a significant effect on the adsorption at pH < 6.0.The adsorption isotherms followed the Langmuir isotherm model well,and the maximum adsorption capacity for Pb(Ⅱ) was 200.38 mg/g for 2Fe-MBC.The adsorption processes were well fitted by a pseudo second-order kinetic model.Thermodynamic parameters showed that the adsorption of Pb(Ⅱ) onto Fe-MBC was feasible,spontaneous,and exothermic under the studied conditions,and the ion exchange mechanism played an significant role.These results have important implications for the design of low-cost and effective adsorbents in the removal of Pb(Ⅱ) from wastewater.     

Adsorption of Mn2+ from aqueous solution using Fe and Mn oxide-coated sand

The adsorption of Mn²⁺ onto immobilized Mn-oxide and Fe-oxide adsorbent such as manganese oxide-coated sand1 (MOCS1), manganese oxide-coated sand2 (MOCS2), iron oxide-coated sand2 (IOCS2), and manganese and iron oxide-coated sand (MIOCS) was investigated. The effects of pH (5.5 to 8.0) and temperature (25 to 45℃) on the equilibrium capacity were examined. Equilibrium studies showed that there is a good fit with both Freundlich and Langmuir isotherm, which indicates surface heterogeneity and monolayer adsorption of the adsorbents. Kinetic data showed high correlation with the pseudo second-order model, which signifies a chemisorption-controlled mechanism. The activation energies, activation parameters (ΔG^*, ΔH^*, ΔS^*), and thermodynamic parameters (ΔG⁰, ΔH⁰, ΔS⁰) confirmed that adsorption with MIOCS was endothermic and more spontaneous at higher temperature while an opposite trend was observed for the other adsorbents. Thermodynamic studies showed that adsorption involved formation of activated complex, where MOCS1 and MIOCS follow a physical-chemical mechanism, while MOCS2 and IOCS2 follows purely chemical mechanism.