Investigation of heavy metal contaminations in the lower Sakarya river water and sediments

In this work, water and sediment samples were collected from three different stations located along the Sakarya river between May and September 2003. Lead, copper, chromium, zinc, nickel and cadmium concentrations were determined by using solvent extraction and flame atomic absorption spectrometric method. The results show that differences based upon sampling times, regions, sediment and water samples were observed. The mean levels of copper, nickel, chromium, lead, cadmium, zinc for sediment samples are; 4.630 μg g⁻¹, 13.520 μg g⁻¹, 8.780 μg g⁻¹, 2.550 μg g⁻¹, 9.990 μg g⁻¹ and for water samples are; 0.851 μg g⁻¹, 1.050 μg g⁻¹, 0.027 μg g⁻¹, 1.786 μg g⁻¹, 0.236 μg g⁻¹, 0.173 μg g⁻¹, respectively.     

The effect of oxidation and acidification on the speciation of heavy metals in sulfide-rich freshwater sediments using a sequential extraction procedure

The speciation of metals in a contaminated, anoxic, sulfide-rich, freshwater sediment was determined experimentally, using a sequential extraction procedure based on the method of Tessier et al. Taking into account the advantages and disadvantages of sequential extractions, the applied methodology allowed the investigation of the influence of aeration and acidification on the distribution of various metals in the sediment. Aeration caused Zn and Cd to be released from sulfides. Carbonates were partly dissolved by the oxidation process, causing mobilisation of Ca. Fe became less mobile owing to a stronger binding to organic matter. The speciation of K, Al, Ni, Pb and Mn and to a lesser extent of Cu was not affected by aeration. As a result of acidification of the aerated sediment, Ca, Mn, Ni, Zn and Cd became more mobile owing to the dissolution of carbonates.     

Assessment of heavy metals in aquatic sediments

The concentration of heavy metals in the bottom sediment and interstitial water collected from two reservoirs in Singapore was found to be enriched. A distribution coefficient,K _d , was used to assess the chemical stability of heavy metals in the sediments. Numerical models were used to assess (1) the redistribution of heavy metals in a changing environment, and (2) long-term self clean-up capabilities of a reservoir.     

Fractionation of heavy metals and phosphorus in suspended sediments of the Yamuna river,India

The Yamuna river is the largest tributary of the Ganges river system. It originates in the Himalayas and flows through a varied geological terrain encompassing a large basin area. Metals Fe, Mn, Pb, Zn, Cu in different chemical fractions of suspended sediments such as exchangeable, carbonates, Fe–Mn oxides, organics and residual fractions were studied. Phosphorus associated with different chemical forms are discussed. The metals are mostly associated with residual fractions in the sediments followed by organics, Fe–Mn oxides, exhangeable and carbonates. Intensive use of chemical fertilizers and pesticides in agriculture in the basin affects the high inorganic phosphorus content in sediments.     

Secondary mobilisation of heavy metals in overbank sediments

Heavy metal mobility was studied in overbank sediments of the Grote Beek river in Central Belgium. The geochemical signature of heavy metals in fine-scale sampled overbank sediments was compared with data on heavy metal emission into the river. The influence of acidification, organic and inorganic complexation on heavy metal mobility in overbank sediments was studied by single and sequential extractions and leaching tests. As confirmed by these tests, the elevated CaCl(2) content of the river water significantly enhanced the mobilisation of especially Cd, while Zn was mobilised to a lesser extent. The mobilisation of As on the other hand decreased in the presence of elevated CaCl(2) concentrations. Based on the results of single extractions, two highly contaminated zones with a different Cd mobility were observed in one of the overbank profiles. A detailed investigation of Cd leaching behaviour in the zone of Fe-accumulation during pH(stat) leaching tests, suggested that it was related to the association of Cd with Fe-oxides, while adsorption was the dominant binding form of Cd in the clay-rich part of the overbank sediment profile.     

Distribution of heavy metals in water and sediments of selected sites of Yamuna river (India)

The concentration of Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn metals in water and sediments of Yamuna river were determined by atomic absorption spectrophotometry in the year 1981. The data showed that there was considerable variation in the concentration of elements from one sampling station to the other which may be due to the variation in the quality of industrial and sewage wasters being added to the river at different sampling stations. The sediment samples collected from different sampling stations were also analysed for calcium carbonate, organic matter, potassium, and phosphorus.     

Short-term accumulative signatures of heavy metals in river bed sediments in the industrial area, Tehran, Iran

In modern civilization, numerous anthropogenic activities release a variety of pollutants into the environment and with anomalous enrichment of heavy metals it causes surface and subsurface contamination. The aquatic sediments provide pertinent tools for the quality assessment of urban and industrial environments in large cities. The present study reveals short-term accumulative trends of heavy metals (Co, Cd, and Pb) in the sand and silt dominated riverbed sediments from Chitgar industrial area (Tehran, Iran) between the period of May 2007 and May 2008. Lead demonstrates highest concentration in residential areas, cadmium in and around industrial areas, whereas cobalt shows least variability. Geo-accumulation index implies moderately to highly polluted sediments with respect to Cd and Pb. With few exceptions, all three metals at different sampling stations display short-term increasing trends, independent of seasonal variability with urban and industrial distends along the river being the chief sources of contamination.     

Accelerated fractionation of heavy metals in contaminated soils and sediments using rotating coiled columns

A new approach to performing an accelerated sequential extraction of trace elements from solid samples has been proposed. It has been shown that rotating coiled columns (RCC) earlier used in counter-current chromatography can be successfully applied to the dynamic leaching of heavy metals from soils and sediments. A solid sample was retained in the rotating column as the stationary phase under the action of centrifugal forces while different eluents (aqueous solutions of complexing reagents, mineral salts and acids) were continuously pumped through. The procedure developed is time saving and requires only 4-5 h instead of the several days needed for traditional sequential extraction (TSE), complete automation being possible. Losses of solid sample are minimal. In most cases the recoveries of readily bioavailable and leachable forms of Pb, Zn, and Cd are higher, if a dynamic extraction in RCC is used. Since naturally occurring processes are always dynamic, continuous extraction in RCC may help to estimate the contents of leachable forms and their potential risk for the environment more correctly than batch TSE. The Kersten-Foerstner and McLaren-Crawford leaching schemes have been compared, the former has been found to be preferable.     

Multivariate analysis of heavy metals concentrations in river estuary

Multivariate statistical techniques such as multivariate analysis of variance (MANOVA) and discriminant analysis (DA) were applied for analyzing the data obtained from two rivers in the Penang State of Malaysia for the concentration of heavy metal ions (As, Cr, Cd, Zn, Cu, Pb, and Hg) using a flame atomic absorption spectrometry (F-AAS) for Cr, Cd, Zn, Cu, Pb, As and cold vapor atomic absorption spectrometry (CV-AAS) for Hg. The two locations of interest with 20 sampling points of each location were Kuala Juru (Juru River) and Bukit Tambun (Jejawi River). MANOVA showed a strong significant difference between the two rivers in terms of heavy metal concentrations in water samples. DA gave the best result to identify the relative contribution for all parameters in discriminating (distinguishing) the two rivers. It provided an important data reduction as it used four parameters (Zn, Pb, Cd and Cr) affording 100% correct assignations. Results indicated that the two rivers were different in terms of heavy metals concentrations in water, and the major difference was due to the contribution of Zn. A negative correlation was found between discriminate functions (DF) and Cr and As, whereas positive correlation was exhibited with other heavy metals. Therefore, DA allowed a reduction in the dimensionality of the data set, delineating a few indicator parameters responsible for large variations in heavy metal concentrations. Correlation matrix between the parameters exhibited a strong evidence of mutual dependence of these metals.     

Speciation of selected heavy metals geochemistry in surface sediments from Tirumalairajan river estuary, east coast of India

Surface sediment samples from the Tirumalairajan river estuary were studied for grain size pattern, organic matter, and heavy metals (Fe, Mn, Zn, and Pb) using the sequential and bulk metal extraction methods to evaluate metal behavior. Ten surface sediment samples were collected during the monsoon and summer seasons of the year 2009. The observed orders of concentrations of heavy metals in the sediments were as follows: Fe?>?Mn?>?Zn?>?Pb. The results obtained from sequential extraction showed that, among the metals studied, a larger portion of the metals were associated with the residual phase, although they are available in other fractions. The low concentration of metals available in bioavailable phases indicated that the sediments of Tirumalairajan river estuary were relatively unpolluted. Correlation analysis was also carried out to understand the associations of metals in different phases with sand, silt, clay, and organic matter. To understand the risk of heavy metals to sediment-dwelling organisms, the data were compared with risk assessment code and sediment quality values using the screening quick reference table. The main source of metals to the estuary is from the irrigation field and its associated activities in the study area.     

Analysis of some heavy metals in the riverine water, sediments and fish from river Ganges at Allahabad

The river Ganges has been one of the major recipients of industrial effluents in India. The present paper deals with the study related to occurrence and bioaccumulation of heavy metals (Cu, Cr, Cd, Pb, Zn) in the riverine water, sediment, and the muscles of two cat fish species, Channa punctatus (C. punctatus) and Aorichthys aor (A. aor) procured from the river Ganges at Allahabad. The data obtained after water analysis reflected the order of occurrence of heavy metals to be Zn > Pb > Cu > Cr > Cd, respectively. The analysis of heavy metals in sediment indicated that among the five heavy metals tested; Zn was maximally accumulated followed by Pb, Cr, Cu and Cd. The trend of heavy metals accumulation in fish muscles was found to be similar to that observed in sediment and water such as Zn > Pb > Cu > Cr > Cd. Data indicated that Zn accumulated maximally in the sediment as well as muscles of both of the fish species in comparison to other metals.     

Mobility and ecological risk assessment of trace metals in polluted estuarine sediments using a sequential extraction scheme

The three-stage sequential extraction procedure for the fractionation of Cd, Cr, Cu, Ni, Pb, and Zn, proposed by the Commission of the European Communities Bureau of Reference, was applied to sediment five samples collected from the Sal estuary, Sergipe State, northeast Brazil, in September 2009. The method showed satisfactory recoveries, detection limits, and standard deviations for determinations of trace metals in the sediments. Cd and Pb were the metals most prevalent in the bioavailable fractions (carbonates, Fe and Mn oxides, organic matter, and sulfides), while Ni, Zn, Cu, and Cr showed higher percentages in the inert fraction. The order of mobility of the metals was Cd (66 %) > Pb (65 %) > Zn (59 %) > Ni (57 %) = Cr (57 %) > Cu (56 %). Possible toxicity related to these metals was examined using the risk assessment code, and by comparing the chemical data with sediment quality guideline ERL-ERM values. Results obtained using the two methods were in agreement, and showed low to medium risk for all metals, indicating that adverse effects on aquatic biota should rarely occur.     

Determination and speciation of heavy metals in sediments of the Juru River,Penang, Malaysia

The Juru River flows through largely urbanized areas and is grossly polluted by domestic wastes and discharges from pig farms. Other than carrying highly polluting organic materials, these wastes are also contaminated with heavy metals. To ascertain the extent of heavy metal pollution in the river, total and non-residual concentrations of Cu, Pb, Zn, Mn and Fe in sediment samples collected along the river were determined. The results indicate that both the total and non-residual metal concentrations in sediments can successfully be used to identify heavy metal pollution sources. The speciation of Zn, Mn and Fe in the sediment samples were investigated using a sequential leaching technique which identifies the elements among six operationally defined host fractions: (1) exchangeable, (2) carbonate and surface-associated, (3) easily reducible, (4) moderately reducible, (5) bound to organic matter and sulphides and (6) residual. The results indicate that Zn is mainly associated with the reducible fractions. Zn and Fe found in the moderately reducible fraction are significantly correlated, indicating that iron oxides is the preferred host phase by Zn.     

Determination of heavy metals (Cd, Cr, Cu, Fe, Ni, Pb, Zn) by ICP-OES and their speciation in Algerian Mediterranean Sea sediments after a five-stage sequential extraction procedure

Surface sediment samples (n = 18) were collected from the Algerian Mediterranean coasts and analyzed for seven metals using inductively coupled plasma-optical emission spectrometry in order to asses the distribution and bioavailability of metals and to study the anthropogenic factors affecting their concentrations. Sediment samples were size-fractionated into three sizes: 1,080–500 (coarse), 500–250 (medium), and <250 mm (fine). Bulk sediments were subjected to both sequential extraction and total digestion to evaluate the reliability of the sequential extraction procedure (SEP), while the fractions have been only sequentially extracted for metals speciation. The metals were sequentially extracted into five phases namely exchangeable (P1), carbonates (P2), Fe–Mn oxides (P3), organic (P4) and residual (P5). Metal recoveries in sequential extractions were ±20% of the independently measured total metal concentrations; the high recovery rates indicate the good reliability of the SEP used in this study. Correlation coefficients indicated that the grain size has an effect on the distribution of metals in the investigated samples. The order of metal levels in the fractions was medium > fine > coarse for all the metals. The average total extractable metal concentrations for Cd, Cr, Cu, Fe, Ni, Pb, and Zn were 1.1, 8.8, 4.7, 1,291.3, 13.9, 5.7 and 20.4 μg/g, respectively. The northeastern shelf had the lowest metal levels while the highest were in northwestern part mainly due to the significant tourism activities in the northwestern part. Comparison of our results to Earth’s crust values and to previous studies points out that our samples were relatively unpolluted with respect to the heavy metals investigated; most of the metals are not from anthropogenic sources. Enrichment factors as the criteria for examining the impact of the anthropogenic sources of heavy metals were calculated, and it was observed that the investigated samples were not contaminated with Cr, Cu, and Fe, moderately contaminated with Ni, Pb, and Cd, and contaminated with Cd in some sites. The P5 phase had the highest percents of Cr, Cu, Fe, Ni, and Zn. Cadmium and lead were predominant in the P4 phase, while Cu, Fe and Zn were distributed in the order P5 > P3 > P4 > P2 > P1. The following order of bioavailability was found with the heavy metals Pb > Cr > Cd > Ni > Zn > Cu > Fe.     

Partition of heavy metals in a tropical river system impacted by municipal waste

A research program was established to identify the governing factors for the partition coefficient (K _D ) of heavy metals between suspended particulate and dissolved phases in the Day River system a tropical, highly alluvial aquatic system, in Vietnam. The targeted river system, draining an urbanized–industrialized catchment where discharged wastewater is mostly untreated, could be separated into the least impacted, pristine area, and the most impacted, polluted area. Organic matter degradation was shown to govern the variation of parameters like total organic carbon, biochemical oxygen demand, chemical oxygen demand, nutrients, conductivity, or redox potential. Heavy metals in both dissolved and particulate phases were enriched in severely polluted area because of wastewater inflow that contains concentrated metals and intensification of metal influx from sediment. Results show log K _D in the order Mn?<?As?<?Zn?<?Hg?<?Ni?<?Cu?<?Cd?<?Co?<?Pb?<?Cr?<?Fe and As?<?Zn?<?Ni?<?Mn?<?Cr?<?Cu?<?Co?<?Fe in the polluted zone and the pristine zone, respectively. A decreasing tendency of partition coefficients of 11 heavy metals considered from the pristine to the impacted zones was observed. Three explanations for the difference are: (1) increase of solubility of most heavy metals in low redox potential, (2) competition for the binding sites with major and minor cations, and (3) complexation with dissolved organic matter concentrated in municipal waste impacted water. Apart from domestic waste impact, statistical analysis has contributed to identify the influence of climate condition and hydrological regime to the partition of heavy metals in the area.     

Development of a hybrid pollution index for heavy metals in marine and estuarine sediments

Heavy metal pollution of sediments is a growing concern in most parts of the world, and numerous studies focussed on identifying contaminated sediments by using a range of digestion methods and pollution indices to estimate sediment contamination have been described in the literature. The current work provides a critical review of the more commonly used sediment digestion methods and identifies that weak acid digestion is more likely to provide guidance on elements that are likely to be bioavailable than other traditional methods of digestion. This work also reviews common pollution indices and identifies the Nemerow Pollution Index as the most appropriate method for establishing overall sediment quality. Consequently, a modified Pollution Index that can lead to a more reliable understanding of whole sediment quality is proposed. This modified pollution index is then tested against a number of existing studies and demonstrated to give a reliable and rapid estimate of sediment contamination and quality.     

Distribution of heavy metals in sediment and water of river Gomti

Gomti river receives industrial as well as domestic wastes from various drains of Lucknow city. In the process the water and sediment of the river Gomti get contaminated with heavy metals and other pollutants. In the present study, impacts of domestic/industrial wastes on the water and sediment chemistry of river Gomti with special reference to heavy metals have been investigated in different seasons (summer, winter and rainy). For this, seven sampling sites: Gaughat, Mohan Meakin, Martyrs Memorial, Hanuman Setu, Nishatganj bridge, Pipraghat and Malhaur, in the river Gomti in Lucknow region were identified and samples of water and sediments were collected in all the three seasons. In the collected water and sediment samples, six metals (Cd, Cr, Cu, Ni, Pb, and Zn) were analyzed on ICP-AES (Inductively coupled plasma emission spectroscopy) Labtam Plasmalab 8440. High concentrations of all the metals were noticed in water and sediment in rainy season compared to summer and winter. Because in rainy season runoff from open contaminated sites, agricultural field and industries, directly comes into the river without any treatment. In both the cases, the concentration of zinc was maximum (0.091 g/ml in water and 182.13 g/g in sediment) and the concentration of cadmium (0.001 g/ml in water and 17.26 g/g in sediment) was minimum. Higher concentration of metal in water and sediment during rainy season could be due to the industrial/agricultural/domestic runoff coming into the river.     

Determination of radioactive elements and heavy metals in sediments and soil from domestic water sources in northern peninsular Malaysia

Soil serves as a major reservoir for contaminants as it posseses an ability to bind various chemicals together. To safeguard the members of the public from an unwanted exposure, studies were conducted on the sediments and soil from water bodies that form the major sources of domestic water supply in northern peninsular Malaysia for their trace element concentration levels. Neutron Activation Analysis, using Nigeria Research Reactor-1 (NIRR-1) located at the Centre for Energy Research and Training, Zaria, Nigeria was employed as the analytical tool. The elements identified in major quantities include Na, K, and Fe while As, Br, Cr, U, Th, Eu, Cs, Co, La, Sm, Yb, Sc, Zn, Rb, Ba, Lu, Hf, Ta, and Sb were also identified in trace quantities. Gamma spectroscopy was also employed to analyze some soil samples from the same area. The results indicated safe levels in terms of the radium equivalent activity, external hazard index as well as the mean external exposure dose rates from the soil. The overall screening of the domestic water sources with relatively high heavy metals concentration values in sediments and high activity concentration values in soil is strongly recommended as their accumulation overtime as a consequence of leaching into the water may be of health concern to the members of the public.     

Characterization of heavy metals in water and sediments in Taihu Lake, China

To explore a comprehensive status of heavy metals in the Taihu Lake, which is one of the most important waters in China, water and sediment samples were taken throughout the lake during April to May of 2010, and metal elements (Cu, Cd, Cr, Ni, Pb, Sn, Sb, Zn, Mn) were analyzed in the water column, interstitial water and sediment. Relevant standards were used to assess the sediment and water quality. Results show that, in the lake water column, the average concentration of all metals ranged from 0.047 μg/l (Cd) to 8.778 μg/l (Zn). The concentration in the river water was usually higher than in the lake water for many metals. In the interstitial water Mn was significantly higher than that in water column, and other metals had no significant difference between the two media. In the surface sediment, average metal content ranged from 1.325 mg/kg (Cd) to 798.2 mg/kg (Mn). Spatially, contents of many metals were higher in Zhushan Bay than in other lake areas, and there existed a clear content gradient from the river to the lake for both water and sediment. On the sediment profiles, many metals presented an increasing trend from the depth of 15-20 cm to the top, which is indicative of the impact of increasingly intensive human activities from that period. Quality assessment indicates that metals in water phase are generally safe compared with USEPA "National Recommended Water Quality Criteria," with the exception of Mn in the interstitial water and Sb in the river water. Whereas the sediment is widely contaminated with metals to some extent compared with the "Consensus-Based Sediment Quality Guidelines," and Cu, Cr, and Ni are more likely to raise ecological risks. This work could be a basis for the ongoing China's criteria strategy.     

Assessment of heavy metals in sediments from a typical catchment of the Yangtze River, China

An intensive investigation was conducted to study the accumulation, speciation, and distribution of various heavy metals (As, Cd, Cr, Cu, Hg, Ni, Pb, and Zn) in sediments from the Yangtze River catchment of Wuhan, China. The potential ecological risks posed by these heavy metals also were estimated. The median concentrations of most heavy metals (As, Cd, Cr, Cu, Ni, Pb, and Zn) were higher than the background values of soils in Wuhan and were beyond the threshold effect level (TEL), implying heavy metal contamination of the sediments. Carbonate-bound Cd and exchangeable Cd, both of which had high bioavailability, were 40.2% and 30.5% of the total for Cd, respectively, demonstrating that Cd poses a high ecological risk in the sediments. The coefficients of the relationship among Pb, Hg, and Cu were greater than 0.797 using correlation analysis, indicating the highly positive correlation among these three elements. Besides, total organic carbon content played an important role in determining the behaviors of heavy metals in sediments. Principal component analysis was used to study the distribution and potential origin of heavy metals. The result suggested three principal components controlling their variability in sediments, which accounted for 36.72% (factor 1: Hg, Cu, and Pb), 28.69% (factor 2: Cr, Zn, and Ni), and 19.45% (factor 3: As and Cd) of the total variance. Overall, 75% of the studied sediment samples afforded relatively low potential ecological risk despite the fact that generally higher concentrations of heavy metals relative to TEL were detected in the sediments.