Heavy metal concentration and speciation of seven representative municipal sludges from wastewater treatment plants in Northeast China

The analysis of heavy metals is very important for assessing the feasibility of the agricultural utilization for the municipal sludge. In this paper, a four-step sequential extraction method was applied to extract heavy metals (Cu, Zn, Mn, Cr, and Ni) in municipal sludges from seven individual wastewater treatment plants located in Jilin and Heilongjiang Province, China, for estimating the mobility and bioavailability of the metal ions in the agricultural application. The total concentrations of heavy metals and their chemical fractions after the sequential extraction were determined. Principal component analysis (PCA) was applied to analyze the relations of heavy metals fractions in the municipal sludges. Experimental results indicated that the total concentrations of Cu, Zn, Cr, and Ni in all sludge samples were below the threshold values set out by the Chinese legislation (GB18918-2002). Specially, Zn had a high bioavailability and mobility, Cu and Cr had potential bioavailability, while Mn mainly existed in the residual fraction of municipal sludge. On the other hand, Ni had different mobility in different municipal sludge. PCA results were confirmed by the environmental behavior of heavy metals.     

Heavy metal concentrations in water and sediments in Tasik Chini, a freshwater lake, Malaysia

The purpose of this paper are to determine the concentration of heavy metals namely cadmium (Cd), copper (Cu) and lead (Pb) in water and sediment; and to investigate the effect of sediment pH and sediment organic matter on concentration of cadmium, copper and lead in sediment at oxidation fraction. For this purpose the concentration of heavy metals were measured in water and sediments at 15 sites from Tasik Chini, Peninsular Malaysia. The sequential extraction procedure used in this study was based on defined fractions: exchangeable, acid reduction, oxidation, and residual. The concentration of heavy metals in residual fraction was higher than the other fractions. Among the non-residual fractions, the concentration of heavy metals in organic matter fraction was much higher than other fractions collected from all sampling sites. The pH of the sediment in all sites was acidic. The mean pH ranges from 4.8 to 5.5 with the higher value observed at site 15. Results of organic matter analysis showed that the percentage of organic matter present in sediment samples varies throughout the lake and all sites of sediments were relatively rich in organic matter ranging from 13.0% to 34.2%. The highest mean percentage of organic matter was measured at sampling site 15, with value of 31.78%.     

Metal Fractionation Studies in Surfacial and Core Sediments in the Achankovil River Basin in India

The Fractionation of Fe, Zn, Cu, Pb, Mn and Cd in the sediments of the Achankovil River, Western Ghats, India using a sequential extraction method was carried out to understand the metal availability in the basin for biotic and abiotic activities. Spatial distribution of heavy metals has been studied. Sediment grain size has significant control over the heavy metal distribution. The fluctuations in their concentration partly depend upon the lithology of the river basin and partly the anthropogenic activities. The sediments are dominated by sand and are moderately to strongly positively skewed and are very leptokurtotic in nature. The quartzite and feldspars are abundant minerals along with significant amount of mica with low clay content. The core sediments show increasing trend of heavy metal concentration with depth due to the recent addition of anthropogenic sources and post-diagenic activities. Significant amount of Cd (18%) was found in carbonate fraction, which may pose environmental problems due to its toxic nature. Small concentrations of metals, except Cd and Cu, are in exchangeable fraction, which indicate low bio-availability. Enrichment Factor (EF) for individual metals shows the contribution from terrregious and in part from anthropogenic sources. Selective Sequential Extraction (SSE) study shows the variation in specific metal distribution pattern, their distribution in different phases and their bio-availability. Maximum amount of the metals were bound to the non-residual fractions (mainly Fe-oxides). Overall, bio-availability of these micronutrients from sediments seems to be very less. Non-residual phase is the most important phase for majority of heavy metals studied. Among the non-residual fraction, maximum amount of the heavy metals bound to Fe-oxides. The study high lights the need for in-depth study of heavy metals distribution and fractionation in the smaller river basins to get precise information on the behavior and transport of heavy metals in the fluvial environment and their contribution to the world ocean.     

Heavy metals partitioning in sediments of the Kabini River in South India

Cu, Cr, Fe, Mn, Ni, Pb, and Zn in the sediments of the Kabini River, Karnataka, India was studied to determine the association of metal with various geochemical phases by sequential extraction. The variations of heavy metal concentration depend on the lithology of the river basin and partly on anthropogenic activities. The Kabini River sediments are dominated by Sargur supracrustals with amphibolites, gneisses, carbonates, and ultrabasic rocks weathering into gneissic and serpentine soils carrying a natural load of cationic heavy metals. The source of heavy metals in the Kabini riverbed sediments is normally envisaged as additional inputs from anthropogenic over and above natural and lithogenic sources. Geochemical study indicates the metals under study were present mostly in the least mobilizable fraction in the overlying water and it is concluded that heavy metals in these sediments are to a great extent derived from multisource anthropogenic inputs besides geochemical background contributions The results show that lead and chromium have higher potential for mobilization from the sediment due to higher concentration at the exchangeable ion and sulfide ion bounded, also Cu and Pb have the greatest percentage of carbonate fraction, it means that the study area received inputs from urban and industrial effluents. Association of the Fe with organic matter fraction can be explained by the high affinity of these elements for the humic substances. Further, Zn and Ni reveal a significant enrichment in sediment and it is due to release of industrial wastewater into the river. These trace metals are possible contaminants to enter into aquatic and food chain.     

Speciative distribution and bioavailability of metals in agricultural soils receiving industrial wastewater

In order to assess the metal pollution status of agricultural lands of Mandi Bahauuddin receiving industrial wastewater, 35 top soil samples were investigated for the determination of selected metal levels, i.e., Fe, Cu, Cd, Cr, Ca, Ni, and Pb by flame atomic absorption spectroscopy under optimum analytical conditions. The distribution of these metals in different operationally defined chemical fractions was also determined by using the sequential extraction technique. The highest mean total concentration was found for Fe while the least one was observed for Pb. All the studied metals were found to be present at levels much enhanced than national and international standards. Moreover, most of the metals were distributed principally in residual fraction with the exception of Ni which was found to be associated mainly with oxidizable fraction. The significant correlations were observed between Fe-Mn oxide-bound and residual fractions and exchangeable and oxidizable fractions for most of the metals. The highest mobility was exhibited by Ni that evidenced its enhanced bioavailability in the soil. The multivariate statistical analyses in terms of principal component analysis (PCA) and cluster analysis (CA) revealed multiple sources for various geochemical fractions of different metals. CA also revealed that the nonresidual fractions of most of the metals were very closely associated while PCA presented a distinctive behavior of Ca in the soil. It was therefore suggested that in order to avoid the metal contamination arising from industrial wastewater, appropriate remediation strategies must be adopted.     

Leaching Characteristics of Heavy Metals and As from Two Urban Roadside Soils

The leaching tests, including the Toxicity Characteristic Leaching Procedure (TCLP), EDTA extraction and BCR sequential extractions before and after EDTA treatments, were performed on two specific soils to elucidate heavy metal-associated mineral fractions and general leachability. The TCLP illustrated the low leachability of heavy metals in soils from two sites. EDTA is a strong chelator and therefore had higher extraction efficiency compared to that of TCLP. The lower extraction percentages by EDTA for As and Sb were found compared to the other heavy metals derived from anthropogenic sources. Sequential extractions showed that the importance of acid-extractable, organically-bound and Fe–Mn oxide fractions was identified for anthropogenic heavy metals with the exception of As and Ni while the importance of residual fraction was identified for endogenous metals. Changes in sequential fractions of heavy metals after leaching with EDTA are very complex and it is difficult to generalize on which fraction was more mobile than the others. These combined results are helpful in elucidating the association of heavy metals to soil fractions and the mobility characteristics of heavy metals under certain environmental conditions.     

Environmental risk assessment of heavy metal extractability in a biosludge from the biological wastewater treatment plant of a pulp and paper mill

A five-stage sequential extraction procedure was used to fractionate heavy metals (Cd, Cu, Pb, Cr, Zn, Fe, Mn, Ni, Co, As, V and Ba) in a biosludge from the biological wastewater treatment plant of Stora Enso Oyj Veitsiluoto Mills at Kemi, Northern Finland, into the following fractions: (1) water-soluble fraction, (2) exchangeable fraction, (3) easily reduced fraction, (4) oxidizable fraction, and (5) residual fraction. The biosludge investigated in this study is a combination of sludge from the primary and secondary clarifiers at the biological wastewater treatment plant. Extraction stages (2)–(4) follow the protocol proposed by the Measurements and Testing Program (formerly BCR Programme) of the European Commission, which is based on acetic acid extraction (stage 2), hydroxylamine hydrochloride extraction (stage 3), and hydrogen peroxide digestion following the ammonium acetate extraction (stage 4). The residual fraction (stage 5) was based on digestion of the residue from stage 4 in a mixture of HF + HNO₃ + HCl. Although metals were extractable in all fractions, the highest concentrations of most of the metals occurred in the residual fraction. From the environmental point of view, it was notable that the total heavy metal concentrations in the biosludge did not exceed the maximal allowable heavy metal concentrations for sewage sludge used in agriculture, set on the basis of environmental protection of soil by European Union Directive 86/278/EEC, and by the Finnish legislation. The Ca (98.6 g kg⁻¹; dry weight) and Mg (2.2 g kg⁻¹; dry weight) concentrations in the biosludge were 62 and 11 times higher than the typical values of 1.6 and of 0.2 g kg⁻¹ (dry weight), respectively, in arable land in Central Finland. The biosludge had a slightly alkaline pH (∼8.30), a high loss-on-ignition value (∼78%) and a liming effect of 10.3% expressed as Ca equivalents (dry weight). This indicates its potential as a soil conditioner and improvement agent, as well as a pH buffer.     

Heavy metal speciation in solid-phase materials from a bacterial sulfate reducing bioreactor using sequential extraction procedure combined with acid volatile sulfide analysis

Heavy metal mobility, bioavailability and toxicity depends largely on the chemical form of metals and ultimately determines potential for environmental pollution. For this reason, determining the chemical form of heavy metals and metalloids, immobilized in sludges by biological mediated sulfate reduction, is important to evaluate their mobility and bioavailability. A modified Tessier sequential extraction procedure (SEP), complemented with acid volatile sulfide (AVS) and simultaneous extracted metals (SEM) measurements, were applied to determine the partitioning of five heavy metals (defined as Fe, Ni, Zn and Cu, and the metalloid As) in anoxic solid-phase material (ASM) from an anaerobic, sulfate reducing bioreactor into six operationally defined fractions. These fractions were water soluble, exchangeable, bound to carbonates (acid soluble), bound to Fe-Mn oxides (reducible), bound to organic matter and sulfides (oxidizable) and residual. It was found that the distribution of Fe, Ni, Zn, Cu and As in ASM was strongly influenced by its association with the above solid fractions. The fraction corresponding to organic matter and sulfides appeared to be the most important scavenging phases of As, Fe, Ni, Zn and Cu in ASM (59.8-86.7%). This result was supported by AVS and SEM (Sigma Zn, Ni and Cu) measurements, which indicated that the heavy metals existed overwhelmingly as sulfides in the organic matter and sulfide fraction. A substantial amount of Fe and Ni at 16.4 and 20.1%, respectively, were also present in the carbonate fraction, while an appreciable portion of As (18.3%) and Zn (19.4%) was bound to Fe-Mn oxides. A significant amount of heavy metals was also associated with the residual fraction, ranging from 2.1% for Zn to 18.8% for As. Based on the average total extractable heavy metal (TEHM) values, the concentration of heavy metals in the ASM was in the order of Cu > Ni > Zn > Fe > As. If the mobility and bioavailability of heavy metals are assumed to be related to their solubility and chemical forms, and that they decrease with each successive extraction step, then the apparent mobility and bioavailability of these five heavy metals in ASM increase in the order of Cu < As < Ni < Fe < Zn. The SEM/AVS ratio was less than one in eight replicate ASM samples, indicating that the ASM was non-toxic with regards to having a low probability of bioavailable metals in the pore water.     

Pollution, fractionation, and mobility of Pb, Cd, Cu, and Zn in garden and paddy soils from a Pb/Zn mining area

This study was conducted to investigate the pollution load index, fraction distributions, and mobility of Pb, Cd, Cu, and Zn in garden and paddy soils collected from a Pb/Zn mine in Chenzhou City, China. The samples were analyzed using Leleyter and Probst’s sequential extraction procedures. Total metal concentrations including Pb, Cd, Cu, and Zn exceeded the maximum permissible limits for soils set by the Ministry of Environmental Protection of China, and the order of the pollution index was Cd > Zn > Pb > Cu, indicating that the soils from both sites seriously suffered from heavy metal pollution, especially Cd. The sums of metal fractions were in agreement with the total contents of heavy metals. However, there were significant differences in fraction distributions of heavy metals in garden and paddy soils. The residual fractions of heavy metals were the predominant form with 43.0% for Pb, 32.3% for Cd, 33.5% for Cu, and 44.2% for Zn in garden soil, while 51.6% for Pb, 40.4% for Cd, 40.3% for Cu, and 40.9% for Zn in paddy soil. Furthermore, the proportions of water-soluble and exchangeable fractions extracted by the selected analytical methods were the lowest among all fractions. On the basis of the speciation of heavy metals, the mobility factor values of heavy metals have the following order: Cd (25.2–19.8%) > Cu (22.6–6.3%) > Zn (9.6–6.0%) > Pb (6.7–2.5%) in both contaminated soils.     

Speciation of selected heavy metals geochemistry in surface sediments from Tirumalairajan river estuary, east coast of India

Surface sediment samples from the Tirumalairajan river estuary were studied for grain size pattern, organic matter, and heavy metals (Fe, Mn, Zn, and Pb) using the sequential and bulk metal extraction methods to evaluate metal behavior. Ten surface sediment samples were collected during the monsoon and summer seasons of the year 2009. The observed orders of concentrations of heavy metals in the sediments were as follows: Fe?>?Mn?>?Zn?>?Pb. The results obtained from sequential extraction showed that, among the metals studied, a larger portion of the metals were associated with the residual phase, although they are available in other fractions. The low concentration of metals available in bioavailable phases indicated that the sediments of Tirumalairajan river estuary were relatively unpolluted. Correlation analysis was also carried out to understand the associations of metals in different phases with sand, silt, clay, and organic matter. To understand the risk of heavy metals to sediment-dwelling organisms, the data were compared with risk assessment code and sediment quality values using the screening quick reference table. The main source of metals to the estuary is from the irrigation field and its associated activities in the study area.     

An assessment of heavy metal contamination in soils of fresh water aquifer system and evaluation of eco-toxicity by lithogenic implications

The chemistry of heavy metals in sediments with respect to bio-availability and chemical reactivity is regulated by pH, texture, and organic matter contents of the sediments and specific binding form and coupled reactivity of the metals within. To focus on the metal distribution (Fe, Mn, Pb, Cd, Zn, Co, Cu, and Cr) and behavior in a fresh water aquifer system along with the ecological toxicity parameters, a four-step sequential extraction method was applied on 18 Eastern Ghats’ type sediments from fluorosis-hit Nayagarh district, India. Geo-accumulation index of metals in the sediments indicates that they are practically uncontaminated and/or less contaminated with and Fe, Mn, and Cu; contaminated to moderately contaminated with Pb, Zn, and Cr; and strongly contaminated with Cd. Rather, more than 80 % recovered Cd metal concentration in sediments constitute the labile fractions. Temporal clustering of metal fractions indicates transition metal fraction distribution claiming the sediment pH regulation. Similarly, base metal distribution accounts for organic carbon and soil conductivity due to their greater availability in exchangeable and sulfide fractions. Correlation analysis and factor analysis scores demonstrate lack of inter-relationship between transition group and base metal fractions. High fluoride concentration in ground water is associated with high sodium-bicarbonate-iron affinity with elevated pH values (i.e., >7.0) and high positive factor score with the total iron concentration in ground water.     

Heavy metals in bottom sediments of Lake Umbozero in Murmansk Region, Russia

Sediment cores collected from different locations of Lake Umbozero were studied with respect to concentration and mobility of trace and heavy metals Co, Cu, Fe, Mn, Ni, Pb, U, and Zn. Lake Umbozero is the second largest lake in the Murmansk Region and subjected to contamination by air-borne emissions and river transportation from the nearby metallurgical and mining industries. Unlike its neighboring, more industry-prone Lake Imandra, Lake Umbozero is relatively unexplored with respect to its state of pollution. In our study, metal distribution in sediments was found to vary with respect to the cores, although in general the concentrations were at the same level throughout the lake indicating uniform horizontal distribution of metals. When compared to Lake Imandra, the concentrations of most of the metals studied were significantly lower and represented the levels in sediments measured in lakes of Kola Peninsula located further off from industrial pollutant sources. An exception was Pb the concentration of which was at the same level as in Lake Imandra, probably due to long-distance transport. Sediment layers were subjected to four-step sequential extraction procedure to reveal the metal distribution in soluble, exchangeable, acid-soluble, and residual fractions. Indicative of their potential higher lability, Mn, U, and Zn were generally found in exchangeable fraction; as also Mn and U extensively in the acid-soluble fraction.     

The Influence of pH on Mobility of Heavy Metals from Municipal Solid Waste Incinerator Fly Ash

Incineration has become one of the principal methods for municipal solid waste disposal particularly in all large cities throughout the world. Currently, the municipal solid waste incinerator fly ashes (MSWIF) are disposed of by landfill. The metal speciation of cadmium (Cd), chromium (Cr), copper (Cu), lead (Pb), and zinc (Zn) in MSWIF after been extracted with water at different pH values were examined using a sequential extraction procedure. The extraction sequence was as follows: (1) Exchangeable (NaOAc, pH 8.2), (2) Bound to Carbonates (NaOAc, pH 5.0), (3) Bound to metal oxides (HONH3Cl), (4) Bound to organic matters (HNO3, H2O2), and (5) Residual (HNO3, HCl, H2O2, HF, 1:3:1:3). The heavy metal contents in the extraction solutions were determined by inductively coupled plasma atomic emission spectrometry. The heavy metal concentrations in the different fractions obtained by sequential extraction show distinct distribution trends. The extractable fraction ranges from 25.5 to 88% of the total element content. With the pH of the extractant fall below the neutral and acidic ranges, the concentrations of heavy metals rise substantially due to the released of metals bound to carbonate fraction.     

Environmentally safe sewage sludge disposal: the impact of liming on the behaviour of Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn

Dewatered sewage sludge containing relatively high total concentrations of Cr (945 micrograms ml-1), Cu (523 micrograms ml-1), Ni (1186 micrograms ml-1) and Zn (2950 micrograms ml-1) was treated with quicklime and sawdust for sludge disinfection and post-stabilisation. The mobility of the heavy metals in the sludge samples was assessed by applying a modified five-step Tessier sequential extraction procedure. Water was added as a first step for estimation of the proportion of the easily soluble metal fractions. To check the precision of the analytical work the concentrations of heavy metals in steps 1-6 of the extraction procedure were summed and compared to the total metal concentrations. The mass balance agreed within +/- 3% for Cd, Cu, Cr, and Zn and within +/- 5% for Ni, Pb, Fe and Mn. Data from the partitioning study indicate that in the lime-treated sludge at a pH of 12 the mobility of Cu and Ni notably increased with the solubilisation of these metals from their organic and/or carbonate and Fe and Mn oxide and hydroxide fractions, respectively. Liming slightly decreased the proportion of other heavy metals in the easily soluble fractions while its impact on the partitioning between other sludge phases was almost insignificant. Due to the increased solubility of Ni and Cu as well as potential Cr oxidation at high pH, liming cannot be recommended for sludge disinfection. Addition of sawdust did not change the heavy metal partitioning.     

Distribution and speciation of selected metals in surface sediments, from the tropical Zuari estuary, central west coast of India

Estuarine sediments are major reservoirs for the metals. Distribution and mobility of metals within estuaries depends strongly on their specific chemical form. In the present study, surface sediments from Zuari estuary, Goa were analysed by a sequential procedure for Fe, Mn, Cu, Zn, Cr and Co to determine their distribution in five geochemical phases (Exchangeable, carbonate, Fe-Mn oxide (reducible) organic bound (oxidisable) and residual). The total metal content, sand, silt, clay and organic carbon were also determined of the surface sediments. The total metal contents were found to be greater than the background concentrations of average shale values as well as to that of earlier studies indicating enrichment probably due to the anthropogenic origin of metals. The results obtained from sequential procedure showed that among the studied elements, Mn and Co are potentially available in the bioavailable fractions (exchangeable, carbonate and Fe-Mn oxide bound fractions) indicating their importance in toxicity whereas rest of the metals viz. Fe, Cu, Zn and to some extent Cr are largely available in residual phase although they are available in other fractions. The main source of metals to the estuary is mining and its associated activities in the study area. Chemical speciation by sequential extraction procedure has helped in assessing the mobility, bioavailability, diagenesis and toxicity of metals and hence giving a better insight into the ultimate fate of pollutants, which are introduced into the estuarine environment. To understand the risk of the metals to the sediment dwelling organisms the data were compared with the Sediment Quality Values (SQV) using SQUIRT. Also, correlation and Factor analysis were carried out to understand the associations of metals in the different fractions with sand, silt, clay, organic carbon and with other metals.     

Speciation and assessment of heavy metals in surface sediments of Jinjiang River tidal reach, southeast of China

The concentration and speciation of heavy metals (Cr, Ni, Cu, Zn, Cd, Pb) in surface sediments (??≤ 63 μm) of Jinjiang River tidal reach are determined to evaluate the metal behavior. A modified BCR three-step sequential extraction procedure is carried out, and the residual fraction is undertaken by microwave-assisted acid digestion. The index of geo-accumulation indicates that Cd appeared highest among all these heavy metals in surface sediments, Cr, Cu, Zn lower, and Ni, Pb the least. The percentage of Zn, Cd is comparatively higher in the acid soluble fraction, Pb and Cu higher in the reductive fraction, indicating larger potential danger to the environment. So it is essential for developing the future remediation plans and pollution control strategies.     

Speciation of metals in bed sediments and water of Qaraaoun Reservoir, Lebanon

Determination of only total element in sediments does not give an accurate estimate of the likely environmental impacts. Speciation study of metals in sediment provides information on the potential availability of metals (toxic) to biota under various environmental conditions. In water, the toxic metal specie is the free hydrated metal ion. The toxicity of metals depends especially on their chemical forms rather than their total metal content. The present study focuses on Qaraaoun Reservoir, Lebanon. Earlier studies focused only on total metal concentrations in sediment and water. The objective of this study was to determine metal speciation (Fe, Cr, Ni, Zn, Cu, Pb, Cd) in the (operationally defined) sediment chemical fractions and metal speciation in reservoir water. This would reflect on metal bioavailability and toxicity. Water samples and bed sediments were collected from nine sites during the dry season and a sequential chemical fraction scheme was applied to the <75-??m sieve sediment fraction. Metal content in each fraction was determined by the FAAS technique. The data showed that the highest percentages of total metal content in sediment fractions were for: Fe in residual followed by reducible, Cr and Ni in residual and in reducible, Cu in organic followed by exchangeable, Zn in residual and in organic, Pb in organic and carbonate, Cd was mainly in carbonate. Total metal content in water was determined by ICP-MS technique and aqueous metal speciation was predicted using AQUACHEM software interfaced to PHREEQC geochemical computer model. The water speciation data predicted that a high percentage of Pb and Ni were present as carbonate complex species and low percentages as free hydrated ions, highest percentage of Zn as carbonate complex species followed by free hydrated ion, highest percentage of Cd as free hydrated ion followed by carbonate complex species. The sensitivity attempt of free hydrated ion of Ni, Zn, Pb, and Cd in reservoir water revealed dependence of Zn and Cd on pH and alkalinity, while Ni and Pb were only dependent on pH.     

Experimental photochemical release of organically bound aluminum and iron in three streams in Maine, USA

In the present study, the BCR (Community Bureau of Reference) sequential procedure has been applied to determine the zinc partition in sediments taken from a river situated in the Southwest of Romania, in a region subject of intense mining activities. The sampling was performed during three sampling expeditions, organized in the spring, summer, and autumn, 2007. The zinc concentration in different fractions was normalized, its concentration being related to the concentrations of some metals (such as Al or Fe) that are naturally present in sediments. The zinc-contaminated sediments from the investigated area have been evaluated by means of combining the analysis data from the BCR sequential extraction with the normalization to the Al content. The most important zinc collector in the samples taken during the three sampling expeditions is the easily soluble fraction, next being amorphous iron and manganese hydrated oxides fraction, followed by organic matter fraction.     

Effect of methods of preparation on distribution of heavy metals in different size fractions of municipal solid waste composts

The present study compares the distribution and nature of heavy metals in composts from 12 cities of India, prepared from different types of processed urban solid wastes, namely mixed wastes (MWC), partially segregated wastes (PSWC), and segregated bio-wastes (BWC). Compost samples were physically fractionated by wet sieving, followed by extraction of heavy metals by dilute HCl and NaOH. Bigger particles (>0.5 mm) constituted the major fraction in all three types of composts and had a relatively lower concentration of organic matter and heavy metals, the effect being more pronounced in MWC and PSWC in which a significant portion of the heavy metals was distributed in finer size fractions. Cd, Ni, Pb, and Zn were extracted to a greater extent by acid than by alkali, the difference being greater in MWC, which contained a higher amount of mineral matter. In contrast, Cu and Cr were extracted to a greater extent by dilute alkali, particularly from BWC containing a higher amount of organic matter. Water-soluble heavy metals were generally related to the water-soluble C or total C content as well as to pH, rather than to their total contents. This study concludes that wet sieving with dilute acid can effectively reduce heavy metal load in MWC and PSWC.     

Fractionation and mobility of cadmium and zinc in urban vegetable gardens of Kano, Northern Nigeria

Metal fractionation provides information on mobility and stability of various metal species which can be used to evaluate the movement of such metals in soils. The effect of wastewater irrigation on the fractions, spatial distribution, and mobility of cadmium (Cd) and zinc (Zn) was investigated in five urban gardens in Kano, Nigeria. Concentration of total Zn in the surface soils (0–20 cm) ranged from 121 to 207 mg kg^− 1 while Cd concentration was 0.3–2.0 mg kg^− 1. Speciation of both heavy metals into seven operationally defined fractions indicated that the most reactive forms extracted with ammonium nitrate and ammonium acetate, also considered as the bioavailable fractions, accounted for 29–42% of total Cd and 22–54% of total Zn, respectively. The weakly bound fractions of Cd and Zn reached up to 50% of the total Cd and Zn concentrations in the soils. Such high proportions of labile Cd and Zn fractions are indicative of anthropogenic origins, arising from the application of wastewater for irrigation and municipal biosolids for soil fertility improvement. Thus, given the predominance of sandy soil textures, high concentrations of labile Cd and Zn in these garden soils represent a potential hazard for the redistribution and translocation of these metals into the food chain and aquifer.