Assessment and analysis of industrial liquid waste and sludge disposal at unlined landfill sites in arid climate

Municipal solid waste disposal sites in arid countries such as Kuwait receive various types of waste materials like sewage sludge, chemical waste and other debris. Large amounts of leachate are expected to be generated due to the improper disposal of industrial wastewater, sewage sludge and chemical wastes with municipal solid waste at landfill sites even though the rainwater is scarce. Almost 95% of all solid waste generated in Kuwait during the last 10 years was dumped in five unlined landfills. The sites accepting liquid waste consist of old sand quarries that do not follow any specific engineering guidelines. With the current practice, contamination of the ground water table is possible due to the close location of the water table beneath the bottom of the waste disposal sites. This study determined the percentage of industrial liquid waste and sludge of the total waste dumped at the landfill sites, analyzed the chemical characteristics of liquid waste stream and contaminated water at disposal sites, and finally evaluated the possible risk posed by the continuous dumping of such wastes at the unlined landfills. Statistical analysis has been performed on the disposal and characterization of industrial wastewater and sludge at five active landfill sites. The chemical analysis shows that all the industrial wastes and sludge have high concentrations of COD, suspended solids, and heavy metals. Results show that from 1993 to 2000, 5.14+/-1.13 million t of total wastes were disposed per year in all active landfill sites in Kuwait. The share of industrial liquid and sludge waste was 1.85+/-0.19 million t representing 37.22+/-6.85% of total waste disposed in all landfill sites. Such wastes contribute to landfill leachate which pollutes groundwater and may enter the food chain causing adverse health effects. Lined evaporation ponds are suggested as an economical and safe solution for industrial wastewater and sludge disposal in the arid climate of Kuwait.     

Solid Waste Recycling And Reuse In Bangkok

Materials recovered from solid waste in Bangkok are mainly glass bottles, paper and paper products, plastic products and metals. Materials are separated at three different stages of the collection process: at the source, prior to collection; by the crews of the collection vehicle; and by the scavengers at the dump site. The total daily tonnage of recyclable garbage collected at the source by the waste pickers is estimated at 286 tonnes, about 5% of the garbage collected by the city. There are small scale recycling shops (SSR) located around the main disposal sites where collected materials are sold by the collection crews and the scavengers. The quantity of materials delivered to the SSR shops by the collection crew vary between 1-6 tonnes per day. The amount of materials recovered by the scavengers (at the dump site) varies between 50-150 kg person^-1 day^-1. Therefore around 7.5% of the solid waste is recycled. In Bangkok both formal and informal sectors manufacture paper pulp, cardboard boxes and magazines from the recyclable paper. Paper products which account for 55% of the total waste stream are considered as the largest "product group" in the municipal solid waste. Recyclable glass (1-3% of the total waste stream) or cullet is used to manufacture plain glasses or cups. Plastics constitute about 10-15% of the waste stream. The benefit/cost ratios of production of most of these industries were reported to be higher than 1.5. In order to enhance recycling, legislative measures need to be introduced and enforced. In Thailand, there is, however, no law concerning recycling. There is no incentive for the consumer to separate solid waste for recycling, as the prices of waste in Bangkok are low and inconsistent. Therefore the pricing system should be more organized for recycling to be more effective.     

Report: biomedical waste management practices at Balrampur Hospital, Lucknow, India.

Biomedical waste has become a serious health hazard in many countries, including India. Careless and indiscriminate disposal of this waste by healthcare establishments and research institutions can contribute to the spread of serious diseases such as hepatitis and AIDS (HIV) among those who handle it and also among the general public. The present study pertains to the biomedical waste management practices at Balrampur Hospital, a premier healthcare establishment in Lucknow, in North India. The study shows that infectious and non-infectious wastes are dumped together within the hospital premises, resulting in a mixing of the two, which are then disposed of with municipal waste at the dumping sites in the city. All types of wastes are collected in common bins placed outside the patients wards. For disposal of this waste the hospital depends on the generosity of the Lucknow Municipal Corporation, whose employees generally collect it every 2 or 3 days. The hospital does not have any treatment facility for infectious waste. The laboratory waste materials, which are disposed of directly into the municipal sewer without proper disinfection of pathogens, ultimately reach the Gomti River. All disposable plastic items are segregated by the rag pickers from the hospital as well as municipal bins and dumps. The waste is deposited either inside the hospital grounds, or outside in the community bin for further transportation and disposal along with municipal solid waste. The open dumping of the waste makes it freely accessible to rag pickers who become exposed to serious health hazards due to injuries from sharps, needles and other types of material used when giving injections. The results of the study demonstrate the need for strict enforcement of legal provisions and a better environmental management system for the disposal of biomedical waste in the Balrampur Hospital, as well as other healthcare establishments in Lucknow.     

An investigation of the presence of methane and other gases at the Uzundere-Izmir solid waste disposal site, Izmir, Turkey

Izmir is a large metropolitan city with a population of 3,114,860. The city consists of 27 townships, each township has a population of not less than 10,000 inhabitants. The two major solid waste disposal sites are in the townships of Uzundere and Harmandali. The amount of solid waste that is disposed at each of these sites is about 800 and 1800 t/day, respectively. In Uzundere, compost is produced from the organic fraction of urban solid wastes while the residual material is deposited at a disposal site with a remaining capacity of 700,000 m(3) as of 2001. Gas monitoring and measurements were carried out at the disposal site in Uzundere. For this purpose, nine sampling wells were drilled on selected locations. Each well was furnished with perforated metal pipes suitable for gas monitoring and measurements. The following gases were monitored: O(2), CH(4), CO, CO(2), and H(2)S. The most important finding was that the concentrations of CH(4) in the wells ranged from 7 to 57%. Dilution of the CH(4) by O(2) down to the LEL levels (5-15%) is always possible and poses a continuing risk at the site. Furthermore, the levels of O(2) require that access to the site be limited to only authorized personnel.     

Management of hazardous waste in Thailand: present situation and future prospects

 This paper deals with the present scenario of hazardous waste management practices in Thailand, and gives some insights into future prospects. Industrialization in Thailand has systematically increased the generation of hazardous waste. The total hazardous waste generated in 2001 was 1.65 million tons. It is estimated that over 300 million kg/year of hazardous waste is generated from nonindustrial, community sources (e.g., batteries, fluorescent lamps, cleansing chemicals, pesticides). No special facilities are available for handling these wastes. There are neither well-established systems for separation, storage, collection, and transportation, nor the effective enforcement of regulations related to hazardous wastes management generated from industrial or nonindustrial sectors. Therefore, because of a lack of treatment and disposal facilities, these wastes find their way into municipal wastewaters, public landfills, nearby dump sites, or waterways, raising serious environmental concern. Furthermore, Thailand does not have an integrated regulatory framework regarding the monitoring and management of hazardous materials and wastes. In addition to the absence of a national definition of hazardous wastes, limited funding has caused significant impediments to the effective management of hazardous waste. Thus, current waste management practices in Thailand present significant potential hazards to humans and the environment. The challenging issues of hazardous waste management in Thailand are not only related to a scarcity of financial resources (required for treatment and disposal facilities), but also to the fact that there has been no development of appropriate technology following the principles of waste minimization and sustainable development. A holistic approach to achieving effective hazardous waste management that integrates the efforts of all sectors, government, private, and community, is needed for the betterment of human health and the environment. Received: February 26, 2001 / Accepted: October 11, 2002     

Municipal solid waste characteristics and management in Allahabad, India

Increasing population levels, rapid economic growth and rise in community living standard accelerates the generation rate of municipal solid waste (MSW) in Indian cities. Improper management of MSW causes hazards to inhabitants. The objectives of the study are to determine the quantitative and qualitative characteristics of MSW along with basic information and to create GIS maps for Allahabad city. The samples have been randomly collected from various locations and analyzed to determine the characteristics of MSW. A questionnaire survey has been carried out to collect data from inhabitants including MSW quantity, collection frequency, satisfaction level, etc. The Geographic Information System (GIS) has been used to analyze existing maps and data, to digitize the existing sanitary ward boundaries and to enter the data about the wards and disposal sites. The total quantity of MSW has been reported as 500 ton/day, and the average generation rate of MSW has been estimated at 0.39 kg/capita/day. The generated ArcGis maps give efficient information concerning static and dynamic parameters of the municipal solid waste management (MSWM) problem such as the generation rate of MSW in different wards, collection point locations, MSW transport means and their routes, and the number of disposal sites and their attributes.     

Solid waste management practices in Turkey

As an economically developing country, Turkey has very well operated integrated solid waste management applications structured on modern facilities, besides over 2,000 scattered open dump areas in the country. Integrated waste management applications seem eligible for the metropolitan cities like Istanbul and Izmit (Kocaeli). Attempts have not been encouraging for the scattered regional settlements using central storage sites due to financial shortages and received rejections from nearby settlements. Small-scale compact solid waste management systems with materials recycling and composting can be more suitable alternatives in the small-scale regional settlements. The major constituents of municipal solid waste are organic in nature and approximately a quarter of municipal solid waste is recyclable. Although paper, including cardboard, is the main constituent, the composition of recyclable waste varies strongly by the source or the type of collection point. Solid wastes need primary treatment in order to be suitable for incineration and composting. Turkey needs to give more emphasis on the usage of modern solid waste removal technologies to overcome the overgrowing solid waste disposal problems.     

Transforming an open dump into a sanitary landfill: a development effort in waste management

Upgrading a crude dump site into a sanitary landfill is a very challenging task; Matuail landfill site in Dhaka posed just such a challenge. From the very beginning, the existing disposal site had been used for the crude dumping of solid wastes. All types of solid wastes were haphazardly disposed of all over the site. The existing drainage channels of the dumping ground were not operational due to blockage by indiscriminate waste dumping. A large amount of leachate oozing out from the waste mixed with storm water and made the site esthetically very displeasing and environmentally unsound. This adverse situation sometimes caused disruption of the waste vehicular movement. Step-by-step improvement measures have been taken in the open dump to make it controlled and sanitary by adopting simple and locally available materials, technical guidelines, and construction techniques.     

The Ümraniye-Hekimbaşi open dump accident

The open dump of Ümraniye-Hekimbaşi was the main solid disposal site of the Asiatic side of Istanbul. At this site, which was in operation since 1976, 1500–2000 tonnes of solid wastes were disposed of daily. No waste compaction was undertaken during placement. The slope formed by the solid wastes was very steep (3 vertical to I horizontal), and recently demolition wastes were disposed of on top of these wastes. On 28 April 1993, an “explosion” took place, followed by the displacement of a large mass of solid wastes which engulfed II houses causing the death of 39 people. This paper investigates the possible reasons for this accident and concludes that it was caused by the initial sliding of the solid wastes, which were not deposited in a stable way, followed by an explosion of the methane generated and retained in the landfill.     

Report: future industrial solid waste management in pars Special Economic Energy Zone (PSEEZ), Iran.

The Pars Special Economic Energy Zone (PSEEZ) is located in the south of Iran, on the northern coastline of the Persian Gulf. This area was established in 1998 for the utilization of south Pars field oil and gas resources. This field is one of the largest gas resources in the world and contains about 6% of the total fossil fuels known. Petrochemical industries, gas refineries and downstream industries are being constructed in this area. At present there are three gas refineries in operation and five more gas refineries are under construction. In this study, different types of solid waste including municipal solid waste (MSW) and industrial wastes were investigated separately. The aim of the study was to focus on the management of the industrial wastes in order to minimize the environmental impact. In the first stage, the types and amounts of industrial waste in PSEEZ were evaluated by an inventory. The main types of industrial waste are oil products (fuel oil, light oil, lubricating oil), spent catalysts, adsorbents, resins, coke, wax and packaging materials. The waste management of PSEEZ is quite complex because of the different types of industry and the diversity of industrial residues. In some cases recycling/reuse of waste is the best option, but treatment and disposal are also necessary tools. Recently a design has been prepared for a disposal site in PSEEZ for the industrial waste that cannot be reused or recycled. The total surface area of this disposal site where the industrial waste should be tipped for the next 20 years was estimated to be about 42 000 m2.     

Evaluation of municipal solid waste flow in the Bandung metropolitan area, Indonesia

This article covers partial results for research which was carried out to determine the effectiveness of municipal solid waste (MSW) recycling in Bandung metropolitan urban areas. It focuses on the results of waste flow analysis as basic information in developing better MSW management systems, especially in applying the reduce, reuse, recycle (3Rs) concept. The dependence upon final disposal sites in MSW management and the difficulties in finding disposal sites have resulted in interest in the 3Rs concept. In this research, the determination of waste compositions and the potential of recycling were evaluated based on data from interviews with householders, members of the nonhousehold sector, and recycling actors and on measurement. The informal sector activities observed were mainly from handcart crews, mobile scavengers, transfer point scavengers, final disposal scavengers, waste traders, and recycling business people at several locations in Bandung and Cimahi cities. The estimated waste recycling and composting by stakeholders has not yet achieved 10% (wet weight) of the total waste generated. As in other major cities in developing countries, the informal sectors hold an important role in the recovery of usable materials from waste. However, inorganic waste recycling activities from this sector have not even reached 8% (wet weight) of the total waste generated.     

Recovery and recycling practices in municipal solid waste management in Lagos, Nigeria

The population of Lagos, the largest city in Nigeria, increased seven times from 1950 to 1980 with a current population of over 10 million inhabitants. The majority of the city's residents are poor. The residents make a heavy demand on resources and, at the same time, generate large quantities of solid waste. Approximately 4 million tonnes of municipal solid waste (MSW) is generated annually in the city, including approximately 0.5 million of untreated industrial waste. This is approximately 1.1 kg/cap/day. Efforts by the various waste management agencies set up by the state government to keep its streets and neighborhoods clean have achieved only minimal success. This is because more than half of these wastes are left uncollected from the streets and the various locations due to the inadequacy and inefficiency of the waste management system. Whilst the benefits of proper solid waste management (SWM), such as increased revenues for municipal bodies, higher productivity rate, improved sanitation standards and better health conditions, cannot be overemphasized, it is important that there is a reduction in the quantity of recoverable materials in residential and commercial waste streams to minimize the problem of MSW disposal. This paper examines the status of recovery and recycling in current waste management practice in Lagos, Nigeria. Existing recovery and recycling patterns, recovery and recycling technologies, approaches to materials recycling, and the types of materials recovered from MSW are reviewed. Based on these, strategies for improving recovery and recycling practices in the management of MSW in Lagos, Nigeria are suggested.     

The current situation of solid waste management in China

With economic development, the quantity of solid waste is increasing rapidly in China; the total quantities of municipal solid waste (MSW), industrial solid waste (ISW), and hazardous waste (HW) in 2002 were 136.5 million tons, 945 million tons, and 10 million tons, respectively. In 2002, the quantity of MSW disposed of was 74.04 million tons, 89.30% of which was landfilled, 3.72% was incinerated, and 6.98% was composted. There are currently 651 disposal facilities for MSW in China. Mining gangue is the largest component of ISW, making up 27.5% of the total. In the Chinese industrial sector, the coal mining and processing industry contributed most to the total quantity of ISW, with 16.0% of the total quantity of ISW generated by this sector. In total, 44% of HW was recycled, 27% was stored, 13.5% was disposed of, and 15.4% was discharged. Of the total HW generated, 40% was produced by the chemical materials and chemical products industry. Five categories of HW, i.e., waste alkali, waste acid, inorganic fluoride waste, copper waste, and inorganic cyanide waste, made up 57.8% of the total HW generated. Solid waste pollution has become a huge challenge faced by those involved in Chinese environmental management, but this can be seen as an opportunity to improve environmental quality. This article introduces the strategies taken to improve solid waste management in China.     

Analysis of potential RDF resources from solid waste and their energy values in the largest industrial city of Korea

The production potential of refuse derived fuel (RDF) in the largest industrial city of Korea is discussed. The purpose of this study is to evaluate the energy potential of the RDF obtained from utilizing combustible solid waste as a fuel resource. The total amount of generated solid waste in the industrial city was more than 3.3 million tonnes, which is equivalent to 3.0 tonnes per capita in a single year. The highest amount of solid waste was generated in the city district with the largest population and the biggest petrochemical industrial complex (IC) in Korea. Industrial waste accounted for 89% of the total amount of the solid waste in the city. Potential RDF resources based on combustible solid wastes including wastepaper, wood, rubber, plastic, synthetic resins and industrial sludge were identified. The amount of combustible solid waste that can be used to produce RDF was 635,552 tonnes/yr, consisting of three types of RDF: 116,083 tonnes/yr of RDF-MS (RDF from municipal solid waste); 146,621 tonnes/yr of RDF-IMC (RDF from industrial, municipal and construction wastes); and 372,848 tonnes/yr of RDF-IS (RDF from industrial sludge). The total obtainable energy value from the RDF resources in the industrial city was more than 2,240,000 × 10⁶ kcal/yr, with the following proportions: RDF-MS of 25.6%, RDF-IMC of 43.5%, and RDF-IS of 30.9%. If 50% or 100% of the RDF resources are utilized as fuel resources, the industrial city can save approximately 17.6% and 35.2%, respectively, of the current total disposal costs.     

Municipal solid waste management in India: From waste disposal to recovery of resources?

Unlike that of western countries, the solid waste of Asian cities is often comprised of 70-80% organic matter, dirt and dust. Composting is considered to be the best option to deal with the waste generated. Composting helps reduce the waste transported to and disposed of in landfills. During the course of the research, the author learned that several developing countries established large-scale composting plants that eventually failed for various reasons. The main flaw that led to the unsuccessful establishment of the plants was the lack of application of simple scientific methods to select the material to be composted. Landfills have also been widely unsuccessful in countries like India because the landfill sites have a very limited time frame of usage. The population of the developing countries is another factor that detrimentally impacts the function of landfill sites. As the population keeps increasing, the garbage quantity also increases, which, in turn, exhausts the landfill sites. Landfills are also becoming increasingly expensive because of the rising costs of construction and operation. Incineration, which can greatly reduce the amount of incoming municipal solid waste, is the second most common method for disposal in developed countries. However, incinerator ash may contain hazardous materials including heavy metals and organic compounds such as dioxins, etc. Recycling plays a large role in solid waste management, especially in cities in developing countries. None of the three methods mentioned here are free from problems. The aim of this study is thus to compare the three methods, keeping in mind the costs that would be incurred by the respective governments, and identify the most economical and best option possible to combat the waste disposal problem.     

Treatment and disposal alternatives for health-care waste in developing countries--a case study in Istanbul, Turkey.

Efficient health-care waste management is crucial for the prevention of the exposure of health-care workers, patients, and the community to infections, toxic wastes and injuries as well as the protection of the environment (Safe Management of Wastes from Health-care Activities. World Health Organization, Geneva). The amount of health-care waste produced in the Istanbul Metropolitan City in Turkey is 30 ton day(-1) in total. The method used for the final disposal of most of the health-care waste of Istanbul is incineration. However, a great portion of the infectious waste is disposed of with the domestic waste into the sanitary landfill because of improper segregation practices applied in the health-care institutions. Therefore the alternatives for the treatment and disposal of health-care waste were evaluated. The technical information related to the available treatment technologies including incineration, microwave irradiation, mobile or stationary sterilization, etc. were also investigated. The capital investment cost, transportation/operational costs for each alternative method and the different locations for installation were compared. When the data collected were evaluated, it was found that separate handling and disposal of health-care waste generated on the European and the Asian sides of the city was the most economic and practicable solution. As a result, it was concluded that the capacity of the Kemerburgaz-Odayeri incineration plant is enough to incinerate the health-care waste generated on the European side of Istanbul, the construction of a new incineration plant or a stationary sterilization unit for the disposal of health-care waste generated on the Asian side was the most effective alternative.     

Rapid assessment of industrial waste production based on available employment statistics

A number of problems arise when trying to ascertain the types and quantities of industrial waste generated by a city or region for waste management purposes. To estimate the amount of industrial waste produced it is often necessary to carry out an industrial waste survey—this can be time consuming and costly and beyond the scope of most authorities in developing countries. INVENT is a computer program developed to predict industrial waste production within an area requiring the minimum of data gathering. It comprises a database containing information on known types and quantities of waste that arise from many different types of manufacturing industry. Using this data amounts of waste for other similar industries in an area can be predicted. Initial predictions are based on waste production per employee in other locations.     

Co-disposal of hazardous and municipal wastes in landfills: Experimental work

During the past 15 years considerable research has taken place in the U.K. to investigate the decomposition processes occurring within municipal waste landfills. This, in turn, has led to a better understanding of the environmental fate of many industrial wastes currently, or formerly, co-disposed with municipal refuse. Codisposal is defined in this paper as the disposal of chemical wastes in an admixture with domestic waste so that full advantage is taken of the attenuation and biochemical processes operating within a landfill to reduce the environmental impact to an insignificant level. Central to this philosophy is the maintenance of a balanced input of different wastes to ensure that attenuation and degradation processes are not overwhelmed. It is contended that co-disposal is an effective disposal option for a wide range of industrial wastes at correctly sited and well managed landfills.Co-disposal research findings for three selected industrial waste types are presented and related to the scientific basis for the prohibition, or continuation of their disposal to landfills.     

Characterization of municipal solid waste from the main landfills of Havana city

The city of Havana, the political, administrative and cultural centre of Cuba, is also the centre of many of the economic activities of the nation: industries, services, scientific research and tourism. All of these activities contribute to the generation of municipal solid waste (MSW), which also impact other Cuban cities. Inadequate handling of waste and the lack of appropriate and efficient solutions for its final disposal and treatment increase the risk and possibility of contamination. The main difficulty in the development of a system of management of MSW lies in the lack of knowledge of the chemical composition of the waste that is generated in the country as a whole, and especially in Havana, where solid waste management decisions are made. The present study characterizes MSW in Havana city during 2004. The Calle 100, Guanabacoa and Ocho Vías landfills were selected for physical-chemical characterization of MSW, as they are the three biggest landfills in the city. A total of 16 indicators were measured, and weather conditions were recorded. As a result, the necessary information regarding the physical-chemical composition of the MSW became available for the first time in Cuba. The information is essential for making decisions regarding the management of waste and constitutes a valuable contribution to the Study on Integrated Management Plan of MSW in Havana.     

Medical waste management in Trachea region of Turkey: suggested remedial action.

The main objective of this paper was to analyse the present status of medical waste management in the Trachea region of Turkey and subsequently to draw up a policy regarded with generation, collection, on-site handling, storage, processing, recycling, transportation and safe disposal of medical wastes. This paper also presents the results of study about awareness on how to handle expired drugs. Initially all health-care establishments in Tekirda?, Edirne and Kyrklareli provinces in Trachea region were identified and the amounts of hospital wastes generated by each of them were determined. Current medical waste-management practices, including storage, collection, transportation and disposal, in surveyed establishments were identified. Finally, according to results, remedial measurements for medical waste management in these establishments were suggested. Unfortunately, medical wastes are not given proper attention and these wastes are disposed of together with municipal and industrial solid wastes. The current disposal method is both a public health and environmental hazard. When landfill sites are visited, many scavengers can be seen sorting for recyclable materials, a practice which is dangerous for the scavengers. In addition, it was found that some staff in health-care establishments are unaware of the hazard of medical wastes. It is concluded that a new management system, which consists of segregation, material substitution, minimization, sanitary landfilling and alternative medical waste treatment methods should be carried out. For the best appropriate medical waste management system, health-care establishment employers, managers and especially the members of house- keeping divisions should be involved in medical waste management practice.