Characteristics of steel slag under different cooling conditions

Four types of steel slags, a ladle slag, a BOF (basic oxygen furnace) slag and two different EAF (electric arc furnace) slags, were characterized and modified by semi-rapid cooling in crucibles and rapid cooling by water granulation. The aim of this work was to investigate the effect of different cooling conditions on the properties of glassy slags with respect to their leaching and volume stability. Optical microscopy, X-ray diffraction, scanning electron microscope and a standard test leaching (prEN 12457-2/3) have been used for the investigation. The results show that the disintegrated ladle slag was made volume stable by water granulation, which consisted of 98% glass. However EAF slag 1, EAF slag 2 and the BOF slag formed 17%, 1% and 1% glass, respectively. The leaching test showed that the glass-containing matrix did not prevent leaching of minor elements from the modified slags. The solubility of chromium, molybdenum and vanadium varied in the different modifications, probably due to their presence in different minerals and their different distributions.     

Leaching assessment of road materials containing primary lead and zinc slags

Characterisation of the leaching behaviour of waste-containing materials is a crucial step in the environmental assessment for reuse scenarios. In our research we applied the multi-step European methodology ENV 12-920 to the leaching assessment of road materials containing metallurgical slag. A Zn slag from an imperial smelting furnace (ISF) and a Pb slag from a lead blast furnace (LBF) are investigated. The two slags contain up to 11.2 wt% of lead and 3.5 wt% of zinc and were introduced as a partial substitute for sand in two road materials, namely sand-cement and sand-bitumen. At the laboratory scale, a leaching assessment was performed first through batch equilibrium leaching tests. Second, the release rate of the contaminants was evaluated using saturated leaching tests on monolithic material. Third, laboratory tests were conducted on monolithic samples under intermittent wetting conditions. Pilot-scale tests were conducted for field testing of intermittent wetting conditions. The results show that the release of Pb and Zn from the materials in a saturated scenario was controlled by the pH of the leachates. For the intermittent wetting conditions, an additional factor, blocking of the pores by precipitation during the drying phase is proposed. Pilot-scale leaching behaviour only partially matched with the laboratory-scale test results: new mass transfer mechanisms and adapted laboratory leaching tests are discussed.     

Application of magnetic separation to steelmaking slags for reclamation

Integrated iron and steel plants generate large amounts of metallurgical slag, which usually contains some quantity of metals or mixtures of oxides that could be treated to be recycled in various applications. The conventional method for disposal of slags is dumping. However, it is possible to process the slags to be used in the production of metallic iron, or as an additive in cement making. In this study, a basic oxygen furnace (BOF) steelwork slag obtained from the Kardemir integrated iron and steel works, Karabuk, Turkey is used. A drum magnetic separator system with pre-engineered crucial processing parameters of drum revolution speed, drum radius, drum flesh thickness, and magnitude of the magnetic field applied is utilized, as these parameters have a competing influence on the results. Subsequently, the effects of slag grain size and the drum-blade gap are investigated in the separation efficiency of magnetic grains. It is found that collection of magnetic grains is improved by decreasing the grain size of slags and moreover, the collection of magnetic grains fraction is increased with an increase in the gap between the blades and drum.     

国内电炉钢发展现状与应用前景

通过电炉铜与转炉铜能耗对比,突显了电炉钢的节能与环保优势,同时介绍了国内外电炉钢应用现状。随着社会工业化的发展所带来的钢铁积蓄量的增加,以及电炉钢技术的不断完善和发展,加之迎合国家低碳经济政策的实施,国内电炉钢发展具有广阔前景。     

The use of waste basic oxygen furnace slag and hydrogen peroxide to degrade 4-chlorophenol

A new treatment method is developed to degrade 4-chlorophenol (4-cp) and its oxidation intermediates. The experimental results of this research demonstrate that 4-cp and its oxidation intermediates can be decomposed completely by basic oxygen furnace slag (BOF slag) with hydrogen peroxide (H₂O₂) in an acid solution. The factors that effect the treatment efficiency were studied including initial concentration of 4-cp, pH of the solution, concentration of H₂O₂ and amount of BOF slag. The BOF slags are final waste materials in the steel making process. The major components of BOF slag are CaO, SiO₂, Fe₂O₃, FeO, MgO and MnO. As the BOF slag in an acid solution, FeO and Fe₂O₃ can be dissociated to produce ferrous ion and ferric ion. Ferrous ion reacts with hydrogen peroxide to form “Fenton's reagent” which can produce hydroxyl radicals (OH^.). Hydroxyl radical possession of high oxidation ability can oxidize organic chemicals effectively. Results show that 100 mg/l of 4-cp is decomposed completely within 30 min by 438.7 g/l BOF slag with 8.2 mM hydrogen peroxide in pH=2.8±0.2 solution. The COD value of the solution is reduced from 290 to 90 mg/l. The factors studied which affect the 4-cp decomposition efficiency were the hydrogen peroxide concentration, BOF slag concentration, pH of the solution and initial concentration of 4-cp. Because large amounts of Fe₂O₃ and FeO are present in the BOF slag, the BOF slag not only has a high treatment efficiency, but also can be used repeatedly.     

炼钢精炼渣气固碳酸化反应吸附CO2

采用炼钢精炼渣,通过气固碳酸化反应吸附CO₂,考察了不同吸附温度下精炼渣对纯CO₂和模拟高炉煤气中CO₂的吸附能力。实验结果表明：吸附温度对精炼渣吸附CO₂反应有显著的影响,升高温度可以提高精炼渣对CO₂的吸附能力;在400 ℃时,精炼渣吸附纯CO₂和模拟高炉煤气中CO₂的量分别为4.7 mg/g和9.8 mg/g;吸附温度升高到500 ℃和550 ℃时,精炼渣对纯CO₂的吸附能力强于高炉煤气中CO₂;在550 ℃时,精炼渣吸附纯CO₂和模拟高炉煤气中CO₂的量达到最高,分别为14.7 mg/g和12.9 mg/g。     

Preparation of glass–ceramics from blast furnace slag and its heavy metal curing properties

Journal of Material Cycles and Waste Management - High-performance slag glass–ceramics were prepared by melting method using rare earth-containing blast furnace slag as the main raw material...     

Mechanical properties and microstructure of ground granulated blast furnace slag-based geopolymer reinforced with polyvinyl alcohol fibers

Journal of Material Cycles and Waste Management - Ground granulated blast furnace slag (GGBFS) is a solid waste characterized by a high reactivity with alkali solutions, which is normally used...     

An overview of recovery of metals from slags

Various slags are produced as by-products in metallurgical processes or as residues in incineration processes. According to the origins and the characteristics, the main slags can be classified into three categories, namely ferrous slag, non-ferrous slag and incineration slag. This paper analysed and summarised the generation, characteristics and application of various slags, and discussed the potential effects of the slags on the environment. On this basis, a review of a number of methods for recovery of metals from the slags was made. It can be seen that a large amount of slags is produced each year. They usually contain a quantity of valuable metals except for blast furnace slag and they are actually a secondary resource of metals. By applying mineral processing technologies, such as crushing, grinding, magnetic separation, eddy current separation, flotation and so on, leaching or roasting, it is possible to recover metals such as Fe, Cr, Cu, Al, Pb, Zn, Co, Ni, Nb, Ta, Au, and Ag etc. from the slags. Recovery of metals from the slags and utilisation of the slags are important not only for saving metal resources, but also for protecting the environment.     

Kinetics of steel slag leaching: Batch tests and modeling

Reusing steel slag as an aggregate for road construction requires to characterize the leaching kinetics and metal releases. In this study, basic oxygen furnace (BOF) steel slag were subjected to batch leaching tests at liquid to solid ratios (L/S) of 10 and 100 over 30 days; the leachate chemistry being regularly sampled in time. A geochemical model of the steel slag is developed and validated from experimental data, particularly the evolution with leaching of mineralogical composition of the slag and trace element speciation. Kinetics is necessary for modeling the primary phase leaching, whereas a simple thermodynamic equilibrium approach can be used for secondary phase precipitation. The proposed model simulates the kinetically-controlled dissolution (hydrolysis) of primary phases, the precipitation of secondary phases (C-S-H, hydroxide and spinel), the pH and redox conditions, and the progressive release of major elements as well as the metals Cr and V. Modeling indicates that the dilution effect of the L/S ratio is often coupled to solubility-controlled processes, which are sensitive to both the pH and the redox potential. A sensitivity analysis of kinetic uncertainties on the modeling of element releases is performed.     

Treatment Of Electric Arc Furnace Dust With A Sustained Shockwave Plasma Reactor

In the reprocessing of steel from automotive scrap, lead, cadmium and zinc, which are volatile constituents, vaporize under the extremely high localized temperatures in an electric arc furnace at the points of contact between the graphite electrodes and the charge. These vapors condense to produce a hazardous dust termed electric arc furnace dust (EFD). This study was undertaken to satisfy the need for a mobile system which could be moved from site to site of generators of EFD to avoid transportation of hazardous waste, and to recycle slags and metallic iron products within the plant. A new type of plasma device, the Sustained Shockwave Plasma (SSP) has been developed and tested for treatment of EFD on a laboratory scale (500 g h^-1). Batch tests show that EFD can be treated to produce a non-hazardous slag and metallic zinc and lead to recycle.     

On the ASR and ASR thermal residues characterization of full scale treatment plant

In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste.Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC – European Waste Catalogue – code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material.     

Soluble salt removal from MSWI fly ash and its stabilization for safer disposal and recovery as road basement material

Fly ash from municipal solid waste incinerators (MSWI) is classified as hazardous in the European Waste Catalogue. Proper stabilization processes should be required before any management option is put into practice. Due to the inorganic nature of MSWI fly ash, cementitious stabilization processes are worthy of consideration. However, the effectiveness of such processes can be severely compromised by the high content of soluble chlorides and sulphates. In this paper, a preliminary washing treatment has been optimized to remove as much as possible soluble salts by employing as little as possible water. Two different operating conditions (single-step and two-step) have been developed to this scope. Furthermore, it has been demonstrated that stabilized systems containing 20% of binder are suitable for safer disposal as well as for material recovery in the field of road basement (cement bound granular material layer). Three commercially available cements (pozzolanic, limestone and slag) have been employed as binders.     

Accelerated carbonation of steel slags in a landfill cover construction

Steel slags from high-alloyed tool steel production were used in a full scale cover construction of a municipal solid waste (MSW) landfill. In order to study the long-term stability of the steel slags within the final cover, a laboratory experiment was performed. The effect on the ageing process, due to i.e. carbonation, exerted by five different factors resembling both the material characteristics and the environmental conditions is investigated. Leaching behaviour, acid neutralization capacity and mineralogy (evaluated by means of X-ray diffraction, XRD, and thermogravimetry/differential thermal analysis, TG/DTA) are tested after different periods of ageing under different conditions.Samples aged for 3 and 10 months were evaluated in this paper. Multivariate data analysis was used for data evaluation. The results indicate that among the investigated factors, ageing time and carbon dioxide content of the atmosphere were able to exert the most relevant effect. However, further investigations are required in order to clarify the role of the temperature.     

Technical and environmental long-term properties of industrial residues--summary of field and laboratory investigations

In Sweden, use of industrial residues is still hindered by concern for their long-term properties. A three-year research project was therefore initiated aiming to (1) identify the crucial processes of ageing related to the usefulness of residues in roads; (2) investigate the consequences of these processes for technical and environmental properties of the residues, and (3) propose a method for accelerated ageing to predict the long-term properties. This paper gives an overview of the project methodology, a summary of the test results and references to papers where further details are given.The project, running through 2006-2008, compared naturally aged samples of two residues used as sub-bases in existing asphalt paved roads with samples of fresh residues from producers’ piles. Steel slag of electric arc furnace (EAF) type and municipal solid waste incinerator (MSWI) bottom ash were chosen. The samples were thoroughly characterised in order to identify which ageing processes had been crucial.The results showed that:

-

Bottom ash from the pavement edge was more aged than bottom ash from the road centre. However, no difference in pH was found, instead the differences were caused by differences in water exposure.

-

Steel slag from the pavement edge showed traces of carbonation and leaching processes, whereas slag from the road centre was identical to fresh slag.

-

Water exposure to the subbase materials after ten years in an asphalt paved road was calculated to less than 0.1-0.5 litres per kg.

-

Ageing reactions in steel slag and MSWI bottom ash, ready for use, were too small to be verified by laboratory measurement of deformation properties under loaded conditions.

An accelerated ageing test for steel slag was set up to achieve the carbonation (decrease in pH) and leaching that was observed in the pavement edge material.An accelerated ageing test for bottom ash was set up to achieve the pozzolan reactions that were observed in SEM analyses of in situ specimens.It is recommended to use uncrushed particles when properties of aged material are studied, in order to preserve the original particle surfaces.     

三维电极的制备及活性艳蓝的降解

以不锈钢基PbO2电极为阳极、同等材质的不锈钢板为阴极,在两电极之间以高炉炼钢废渣为填充粒子,自制改进三维电极反应器.通过自制的三维电极反应器,采用电催化氧化法降解活性艳蓝染料.实验结果表明,在废渣加入量为20 g/L、电极间距为10 mm、槽电压为8V的条件下,处理500 mL质量浓度为30 mg/L的活性艳蓝溶液,...     

Cost effective waste management through composting in Africa

Greenhouse gas (GHG) emissions per person from urban waste management activities are greater in sub-Saharan African countries than in other developing countries, and are increasing as the population becomes more urbanised. Waste from urban areas across Africa is essentially dumped on the ground and there is little control over the resulting gas emissions. The clean development mechanism (CDM), from the 1997 Kyoto Protocol has been the vehicle to initiate projects to control GHG emissions in Africa. However, very few of these projects have been implemented and properly registered. A much more efficient and cost effective way to control GHG emissions from waste is to stabilise the waste via composting and to use the composted material as a soil improver/organic fertiliser or as a component of growing media. Compost can be produced by open windrow or in-vessel composting plants. This paper shows that passively aerated open windrows constitute an appropriate low-cost option for African countries. However, to provide an usable compost material it is recommended that waste is processed through a materials recovery facility (MRF) before being composted. The paper demonstrates that material and biological treatment (MBT) are viable in Africa where they are funded, e.g. CDM. However, they are unlikely to be instigated unless there is a replacement to the Kyoto Protocol, which ceases for Registration in December 2012.     

Model-based prediction of long-term leaching of contaminants from secondary materials in road constructions and noise protection dams

In this study, contaminant leaching from three different secondary materials (demolition waste, municipal solid waste incineration ash, and blast furnace slag) to groundwater is assessed by numerical modeling. Reactive transport simulations for a noise protection dam and a road dam (a typical German autobahn), in which secondary materials are reused as base layers, were performed to predict the breakthrough of a conservative tracer (i.e., a salt) and sorbing contaminants (e.g., PAHs like naphthalene and phenanthrene or heavy metals) at the groundwater table. The dam constructions have a composite architecture with soil covers in inclined layers and distinct contrasts in the unsaturated hydraulic properties of the used materials. Capillary barrier effects result in strong spatial variabilities of flow and transport velocities. Contaminant breakthrough curves at the groundwater table show significant tailing due to slow sorption kinetics and a wide distribution of travel times. While conservative tracer breakthrough depends primarily on subsoil hydraulic properties, equilibrium distribution coefficients and sorption kinetics represent additional controlling factors for contaminant spreading. Hence, the three secondary materials show pronounced differences in the temporal development of leached contaminant concentrations with consequences for breakthrough times and peak concentrations at the groundwater table. Significant concentration reductions due to dispersion occur only if the source concentrations decrease significantly prior to the arrival of the contaminant at the groundwater table. Biodegradation causes significant reduction of breakthrough concentrations only if flow velocities are low.     

Reuse of residues arising from lead batteries recycle: a feasibility study

The performance of products arising from the stabilization/solidification of slags from lead batteries recycle into a Portland cement matrix has been evaluated not only in order to get a stabilized waste to be disposed of according to the current legislation, but also to obtain a recyclable material, with both economic and environmental benefits. Under this respect a detailed characterization of raw slags has been performed and different slag-cement samples have been prepared by varying the slag content. The parameters related to the cementation process have been evaluated and a series of tests on the final waste forms have been carried out, aimed at assessing both mechanical performance and leaching behaviour. In spite of the acceptable values for flexural, compressive and tensile strength, however, the high release of lead from the solidification products seems to be a limiting factor for a reusable material. While explanations of such phenomenon are given (high alkalinity of Portland cement; early "doping" of cementitious components by lead in the amorphous state), the main conclusion of the research work is that further efforts should be addressed to the adoption of a different or a modified incorporation matrix.     

Properties of alkali-activated systems with stone powder sludge

This article investigates the effects of stone powder sludge on the microstructure and strength development of alkali-activated fly ash and blast furnace slag mixes. Stone powder sludge produced from a crushed aggregate factory was used to replace fly ash and granulated blast furnace slag at replacement ratios of 0%, 10%, 20%, and 30% by mass. The unit weight and compressive strength of the samples were measured, and scanning electron microscopy/energy dispersive spectroscopy and X-ray diffraction (XRD) analyses were performed. The test results indicated that the compressive strength of alkali-activated blast furnace slag mixes using stone powder sludge was higher than that of the alkali-activated blast furnace slag control mix, but the compressive strength of alkali-activated fly ash mixes decreased with increasing replacement ratio of stone powder sludge. Microscopy results indicated that for alkaliactivated blast furnace slag samples, broken surfaces were more evident than for the alkali-activated fly ash samples. For all XRD diagrams, broad and diffuse peaks were observed around 2θ = 35° (d = 2.96–3.03 Å), implying amorphous or short-ordering structure phases.