液化石油气站储罐区火灾爆炸危险性分析与安全措施

选择具体的液化石油气储配站,分析了该站的危险特性、危险产生的途径及可能造成的后果。在没有任何防护措施的情况下,采用蒸气云爆炸和沸腾液体扩展蒸气云爆炸模型,对该站一个50m3储罐发生泄漏造成的火灾爆炸事故后果进行预测,得出火灾爆炸后的安全距离为大于211．0m。在储配站不能满足此安全距离的基础之上,从防止产生爆炸性气体环境、消除点火源和抑制事故扩大三方面来提出有效的安全措施,降低事故发生的概率及事故造成的损失。其中,站址选在全年最小频率风向的上风侧且周围空旷的地区,罐上设置液位计、压力表、温度计及可燃气体报警器可防止产生爆炸性气体环境;罐及管道设静电接地,法兰用铜线跨接,站内设警示标志可消除点火源;生产区与辅助区间设置隔离墙,罐区周围设置砖混围堤,罐上设安全阀可抑制火灾爆炸事故扩大。     

Impact of leakage location and downwind storage tank on the gas dispersion in a typical chemical tank storage area

Toxic gas leakage in a tank area can have catastrophic consequences. Storage tank leakage location (particularly for high leakage) and downwind storage tanks potentially influence gas diffusion in tank areas. In this study, we developed a numerical and experimental method to investigate the impact of a high leakage location and downwind storage tank on gas diffusion based on three (1.05H, 0.90H, and 0.77H, H was the tank height, 22m) leakage field experiments on the leeward side of storage tank, which have been not conducted before. The experiments revealed an unexpected phenomenon: the maximum ground concentration first decreased and then increased with increasing leakage height. The simulations illustrated that the differences in micrometeorological conditions caused the maximum ground concentration of gas emitted from the roof to be higher than that emitted from the tank wall near the storage tank height. The downwind storage tank 1) had little influence on the entire diffusion direction but altered the local diffusion pattern; 2) reduced the maximum ground concentration (∼18.7%) and the distance from the emission source (approximately a storage tank diameter); and 3) had strong influences on the concentration, velocity, turbulence, and pressure on the leeward side. The concentration negatively correlated with the velocity, pressure, and turbulence in the middle of the two storage tanks on wind centerline. Our results can improve understanding of gas dispersion in tank areas and provide references for mitigating loss and protecting lives during emergency response processes.     

LNG加气站槽车卸车直供过程泄漏后果分析*

为研究LNG加气站槽车直接供液过程泄漏后果严重程度,采用HAZOP辨识槽车供液和储罐供液典型泄漏场景,基于PHAST分析不同泄漏场景下LNG液池半径、蒸汽云扩散距离及积聚时长、爆炸超压和池火热辐射影响范围,定量评价槽车供液可能造成的事故后果扩大程度。结果表明:槽车供液泄漏事故的LNG液池最大半径、蒸汽云最大扩散距离、爆炸超压最大影响半径和池火热辐射最大半径,分别为储罐供液的5.7,1.7,2.3,7.9倍;槽车在无人值守条件下泄漏形成的LNG液池最大半径和蒸汽云积聚时长,分别为有人值守下的1.85,56倍;日供液量较大加气站不宜采用槽车直接为汽车供液模式,而应采用先卸车入罐、再储罐供液的模式;应落实槽车卸车轮班值守制度,并与周边社区建立有效的应急联动方案。     

天然气储气罐破坏效应分析

针对城市天然气储气罐的不断兴建与发展趋势的大型化,对于已建和待建储罐区对周围环境的潜在安全性问题,指出运用破坏伤害范围评价法可直观地预测破坏效应。通过对储罐爆炸释放能量的估算,采用模拟比法结合TNT爆炸试验数据计算出距离储气罐不同距离处爆破冲击波超压值,运用超压准则模拟预测出不同规格、储压下储罐爆破破坏伤害严重程度及危及半径范围;采用世界银行推荐的危害关系式,结合伤害破坏等级分析天然气爆炸破坏效应并与爆破效应比较。5000m3储气罐、储压1.20MPa下,储罐爆破和天然气爆炸危及距离分别可达144.0m和247.7m。依据预测结果,可将罐区周围划分不同区域,为实际工程中罐区选址、建设、安全距离确定及安全预案制定提供参考。     

原油储罐区可燃气体探测器布置优化方案研究

为有效预警原油储备区储罐气体泄漏,制定气体探测器布置优化方案,以某大型原油站库为例,基于CFD法和FLACS软件模拟原油泄漏及可燃蒸汽云溢散分布,通过分析蒸汽云扩散规律,实现全方位气体探测器优化布置.结果表明:原油储罐区探测器分别布置在区块21-2、6-1、31-1、40-2,且每个罐组总计布置16处;优化设置方案可满...     

埋地油罐事故伤害范围模拟评价

分析埋地油罐可能发生的火灾爆炸事故,建立事故模拟模型,模拟爆炸物质完全燃烧的质量依据化学计量浓度确定,事故伤害范围的计算用G.M莱克霍夫在砂质土壤中爆炸的冲击波计算方法。对50 m3埋地油罐模拟,油蒸气形成爆炸性混合气体爆炸伤害范围较大,安全范围与《汽车加油加气站设计与施工规范》中相关规定相符合。模拟方法用于埋地储罐的定量安全评价,为罐区选址、建设、安全距离确定及安全预案制定提供参考。     

Blast damage to storage tanks and steel clad buildings

The 2005 Buncefield vapour cloud explosion showed the huge cost associated with blast damage to commercial property surrounding a major explosion incident. In most cases there was serious disruption to business activity; in many cases the buildings had to be demolished or abandoned for long periods until extensive repairs were carried out.Another key feature of this and other recent vapour cloud explosions has been the damage done to storage tanks. The blasts almost invariably cause immediate top and bund fires in any tanks surrounded by the vapour – even if they contain relatively high flashpoint materials such as diesel.The first part of this paper describes the patterns of damage observed in buildings in the industrial estates around Buncefield. Methods for assessing the degree of external and internal damage are presented.The second part of the paper deals with failure modes and ignition of various types of liquid storage tank during vapour cloud explosions. Again, the Buncefield data provides excellent examples that illustrate the importance of tank design, fill level, location relative to the cloud, etc.     

Wire-mesh inhibition of jet fire induced by explosion venting

Explosion venting is widely applied in industrial explosion-proof designs due to the convenient, economical and practical features of this method. Natural gas is usually stored in storage tanks. If the gas in the vessel is mixed with air and encounters an ignition source, explosion venting might occur, producing jet fire, generating new secondary derivative accidents and causing casualties and property losses. In this paper, a set of test platforms including wire-mesh suppression devices is established to study the inhibition of jet fire induced by explosion venting by wire mesh. The experimental research shows that a wire mesh significantly inhibits the jet fire induced by explosion venting. The flame propagation velocity and pressure clearly decrease with increasing numbers of wire-mesh layers. The wire-mesh structure significantly affects the flame propagation, and the more layers of mesh there are, the better the suppression effect is. The flame temperature gradually decreases with the addition of the wire mesh. The mesh size significantly affects the pressure propagation of explosion venting. The explosion pressure gradually decreases with the addition of the wire mesh. With increasing distance between the wire mesh and the explosion vent, the maximum temperature first increases and then decreases, and the maximum explosion pressure first decreases and then increases. In the case of single gas cloud, the flame suppression effect is the most obvious when the wire mesh is 0.2 m away from the explosion vent. In the case of double gas clouds, the flame suppression effect is the most significant when the distance between the wire mesh and the first gas cloud is 0.4 m.     

Influence of built-in obstacles on unconfined vapor cloud explosion

The obstacle structure in the vapor cloud has a significant influence on the gas explosion. Obstacles could not only lead to the acceleration of flame, but also they may occupy some space, thus affecting the amount of combustible gas. In this paper, a new two-step method was proposed to respectively study the effects of the obstacles amount and volume blockage ratio (VBR) on the gas explosion by using Computation Fluid Dynamic software AutoReaGas, and the obstacles in the vapor cloud were set to “Solid” instead of “Subgrid”. Based on the results and analysis, it is found that the peak overpressure and the maximum combustion rate rise with the increase of the number of obstacles for a single VBR, which indicated that the vapor cloud explosion of more obstacles was more dangerous for a single VBR. However, under a single number of obstacles, the peak overpressure and the maximum combustion rate increase firstly and then decrease as VBR increases and reach the highest at the VBR of 0.74, which indicated that the intensity of vapor cloud explosion reach a peak at a certain VBR in the middle instead of the largest. In addition, the existence and structure of obstacles have little effect on the size of explosion fireball when the size and concentration of combustible gas cloud are the same.     

高压储氢系统泄漏爆炸事故的动力学演化

为研究燃料氢气泄漏、爆炸的特性和规律,预防高压储氢系统中氢气泄漏爆炸事故发生,以加氢站为背景,数值仿真45 MPa高压储罐氢气泄漏并引发爆炸事故,分析泄漏爆炸动力学性质以及爆炸波在非均匀氢气浓度中的传播机制。同时,基于泄漏爆炸事故演化的力学机理,开展氢气泄漏爆炸动态风险分析,针对氢气不同泄漏量,建立泄漏扩散形成的气云体积、气云爆炸产生的冲击波与空间x,z方向上危害距离之间关系。研究结果表明：氢气泄漏过程中,气云氢气浓度变化与流场雷诺数具有较好一致性;氢气扩散受到高压储氢罐周围装置影响,流场中氢气浓度分布不均匀;当发生燃烧爆炸事故时,冲击波参数和湍动能变化梯度大;得到复杂布局区域冲击波超压峰值与比例距离之间关系式,其相比于理论方法更精细、计算结果更准确。研究结果可为降低高压储氢系统泄漏爆炸事故后果、采取有效防护措施提供一定依据。     

Gas explosion analysis of safety gap effect on the innovating FLNG vessel with a cylindrical platform

After investigating gas dispersion on a cylindrical Floating Liquefied Natural Gas (FLNG) platform (Li et al, 2016), this second article focuses on assessment of gas explosion by using Computational Fluid Dynamics (CFD). Gas explosion simulations are carried out to evaluate the explosion overpressure mitigating effect of safety gap. The Data-dump technique, which is an effective tool in resetting turbulence length scale in gas explosion overpressure calculation, is applied to ensure simulation accuracy for the congestion scenario with safety gap. Two sets of different safety gaps are designed to investigate the safety gap on the cylindrical FLNG platform, the overall results indicate that the safety gap is effective in reducing overpressure in two adjacent congestions. However, for the explosion scenario where the flame is propagating through several safety gaps to the far field congestion, the safety gap mitigates overpressure only in certain explosion protecting targets. Two series of artificial configurations are modeled to further investigate the explosion scenarios with more than two safety gaps in one direction. It is concluded that the optimal safety gap design in overpressure mitigation for the cylindrical FLNG platform is to balance the safety gap distance ratio in the congested regions.     

化工储罐间距和体积对爆炸碎片多米诺效应概率的影响

化工储罐爆炸后将产生大量碎片,这些抛射碎片一旦击中相邻罐体容易引发多米诺效应。碎片的抛射方位和抛射距离具有很大的随机性,已有研究多采用概率模型来描述碎片抛射的各分过程。通过总结和发展已有的分过程模型,建立了求取多米诺效应的综合概率模型,并基于蒙特卡罗算法编制了模拟软件,可对化工储罐多米诺效应的发生概率进行预测计算。选取若干常用化工球罐为相邻目标储罐进行实例分析,计算结果表明储罐间距和体积是影响多米诺效应发生概率的两个重要影响因素：随着距离的增大,多米诺效应发生概率不断减小;目标储罐体积越大,多米诺效应发生概率将越大。其中,爆炸碎片对目标储罐的击中概率受上述因素的影响程度更大。该文工作对化工储罐区的安全评价具有一定的参考价值。     

碳纤维含量对球形非金属阻隔防爆材料防爆性能的影响

在临界起爆能和高起爆能条件下,对装填碳纤维含量分别为6.5%、8.0%、9.5%和 11.0%球形非金属阻隔防爆材料的油箱进行等效静爆试验,探究球形非金属阻隔防爆材 料中碳纤维含量对其防爆性能的影响。利用红外热成像仪、高速摄像机分别记录油箱爆 炸火球的温度场参数及爆炸过程,并与未填装阻隔防爆材料的油箱进行对比。试验结果 表明:在临界起爆能条件下,装填4种材料的油箱均有一定阻燃防爆效果,油箱爆炸产 生的燃料云团面积有依次减小的趋势;在高起爆能量条件下,4种材料的外场防爆性能 分数分别为16.93、22.04、32.51、94.18,材料的防爆能力随着碳纤维含量的增加而增 强。     

Forced ventilation effect by Air-Fin-Cooler on flammable gas cloud dispersion

This paper is the second installment of a paper published on Process Safety and Environment Protection in 2013, which evaluates the Air-Fin-Cooler (AFC) forced ventilation effect over natural ventilation inside congested LNG process train, i.e., modularized LNG, considering the Air Change per Hour (ACH) using Computational Fluid Dynamics (CFD) analysis. This second paper evaluates the effect of forced ventilation on gas cloud dispersion using CFD in order to evaluate possible design measures, such as safety distance in trains and whether to shut down the AFC in case of releases. The results of this evaluation show that gas cloud accumulation is reduced by AFC induced air flow in the case of shorter separation distances between modules. Based on the results, two design measures are proposed, i.e., keep AFC running during emergency and train orientation against prevailing wind direction.     

Study of the situation deduction of a domino accident caused by overpressure in LPG storage tank area

The production and storage of liquefied petroleum gas (LPG) is gradually becoming larger and more intensive, which greatly increases the risk of the domino effect of an explosion accident in a storage tank area while improving production and management efficiency. This paper describes the construction of the domino effect scene of an explosion accident in an LPG storage tank area, the analysis of the characteristics of the LPG tank explosion shock wave and the target storage tank failure, and the creation of an ANSYS numerical model to derive the development trend and expansion law of the domino accident in the LPG storage tank area. The research showed that: 400 m³ tank T1 explosion shock waves spread to T2, T4, T5, T3, and T6, and the tank overpressures of 303 kPa, 303 kPa, 172 kPa, 81 kPa, and 61 kPa respectively. The critical values of the target storage tank failure overpressure-range threshold were 70 kPa and 60 m. After the explosion of the initial unit T1 tank, at 38 ms, the T2 and T4 storage tanks failed and exploded; at 56 ms, the T5 storage tank exploded for the third time; at 82 ms, the T3 storage tank exploded for the fourth time; and at 102 ms, the T6 storage tank exploded for the fifth time. With the increase of explosion sources, the failure overpressure of the target storage tank increased, and the interval between explosions continuously shortened, which reflected the expansion effect of the domino accident. The domino accident situation deduction in the LPG storage tank area provided a scientific basis for the safety layout, accident prevention and control, emergency rescue, and management of a chemical industry park.     

储罐爆炸碎片最可能抛射距离的Monte-Carlo(蒙特卡罗)数值模拟

在总结前人工作的基础上,推导了储罐爆炸碎片抛射距离的理论计算公式,并给出具体的计算方法;分析了计算参数的不确定性,同时介绍用Monte-Carlo方法模拟高压储罐爆炸时碎片抛射距离的算法;在数值模拟结果的基础上,计算了碎片抛射距离的分布函数和概率密度函数,引入最可能抛射距离的概念,并指出可以用此来确定碎片抛射的危害范围。该方法对于定量评价储罐爆炸碎片危害性,减缓和控制碎片产生的风险,具有重要的意义。     

开敞空间可燃气云爆炸冲击波超压及灾害动力响应研究评述

为了进一步梳理和分析开敞空间可燃云爆炸冲击波超压传播规律及灾害动力响应方面的各项研究成果,推进可燃气体爆炸安全防控,减少人员伤亡和经济损失。在分析现有研究的基础上,总结开敞空间可燃气云爆炸冲击波超压传播规律及灾害动力响应研究等方面存在的不足,提出开敞空间多元混合气体爆炸冲击波超压传播规律研究、多影响参数下可燃气云爆炸冲击波超压传播规律定量分析、基于可燃气云爆炸冲击波超压作用下的承载体动力响应等未来研究的关键技术问题。     

基于蒙特卡洛法的储罐爆炸碎片冲击失效模型研究

为定量研究相邻储罐间爆炸碎片冲击的多米诺效应,基于蒙特卡洛方法建立爆炸碎片冲击失效模型。该模型共包括爆炸能量与碎片初始速度、考虑风速及碎片初始位置的碎片三维抛射轨迹、空气阻力、碎片冲击穿透等4个分步模型。基于上述模型,研究储罐爆炸后碎片的初始状态、抛射轨迹以及对相邻储罐的冲击效应。在数值模拟结果的基础上,用储罐最高允许工作压力代替泄放装置的泄压压力来计算爆炸压力,绘制碎片质量及初始速度的直方图,定量分析储罐间距对击中概率的影响。结果表明,热辐射、超压和碎片冲击3种能量作用方式均可能导致储罐间火灾爆炸事故多米诺现象发生,但爆炸碎片冲击导致相邻罐失效的概率较低。     

聚乙烯醇罐区火灾爆炸事故树分析

通过现场的调研与事故树分析相结合的手段对某厂聚乙烯醇车间聚合罐区火灾爆炸事故的危险因素进行了识别与分析.以该罐区可能发生的火灾爆炸事故作为顶上事件,对可能引发顶上事件的21个基本事件及一个条件事件构建事故树,利用最小割集、最小径集及结构重要性计算手段进行事故风险程度分析,从而确定醋酸乙烯暴聚是聚合罐区的首要危险源,而促发醋酸乙烯暴聚的物料长时间停留、气相氧含量过高、温度控制失效、阻聚剂含量不足等四个基本事件是导致聚合罐区火灾爆炸事故的最危险因素.本文对以上聚合罐区发生火灾爆炸事故的风险因素进行详细定性分析,并在此基础上有针对性的提出了相应的安全预防控制措施.同时,该聚合罐区的事故树分析结论也可以为同类别化工单位罐区的日常运行、设计改造、维护保养等工作提供理论依据.