Biomass waste gasification - can be the two stage process suitable for tar reduction and power generation?

A pilot scale gasification unit with novel co-current, updraft arrangement in the first stage and counter-current downdraft in the second stage was developed and exploited for studying effects of two stage gasification in comparison with one stage gasification of biomass (wood pellets) on fuel gas composition and attainable gas purity. Significant producer gas parameters (gas composition, heating value, content of tar compounds, content of inorganic gas impurities) were compared for the two stage and the one stage method of the gasification arrangement with only the upward moving bed (co-current updraft). The main novel features of the gasifier conception include grate-less reactor, upward moving bed of biomass particles (e.g. pellets) by means of a screw elevator with changeable rotational speed and gradual expanding diameter of the cylindrical reactor in the part above the upper end of the screw. The gasifier concept and arrangement are considered convenient for thermal power range 100-350 kW_th. The second stage of the gasifier served mainly for tar compounds destruction/reforming by increased temperature (around 950 °C) and for gasification reaction of the fuel gas with char. The second stage used additional combustion of the fuel gas by preheated secondary air for attaining higher temperature and faster gasification of the remaining char from the first stage. The measurements of gas composition and tar compound contents confirmed superiority of the two stage gasification system, drastic decrease of aromatic compounds with two and higher number of benzene rings by 1-2 orders. On the other hand the two stage gasification (with overall ER = 0.71) led to substantial reduction of gas heating value (LHV = 3.15 MJ/Nm³), elevation of gas volume and increase of nitrogen content in fuel gas. The increased temperature (>950 °C) at the entrance to the char bed caused also substantial decrease of ammonia content in fuel gas. The char with higher content of ash leaving the second stage presented only few mass% of the inlet biomass stream.     

Fate of heavy metals and radioactive metals in gasification of sewage sludge

The fates of radioactive cadmium, strontium, cesium, cobalt, arsenic, mercury, zinc, and copper spiked into sewage sludge were determined when the sludge was gasified by a process that maximizes production of char from the sludge (ChemChar process). For the most part the metals were retained in the char product in the gasifier. Small, but measurable quantities of arsenic were mobilized by gasification and slightly more than 1% of the arsenic was detected in the effluent gas. Mercury was largely mobilized from the solids in the gasifier, but most of the mercury was retained in a filter composed of char prepared from the sludge. The small amounts of mercury leaving the gasification system were found to be associated with an aerosol product generated during gasification. The metals retained in the char product of gasification were only partially leachable with 50% concentrated nitric acid.     

Reduction of hazardous elements contained in sewage sludge incineration ash

Research and experimental studies were carried out in relation to reduction of hazardous elements contained in sewage sludge incineration ash. A questionnaire survey was conducted in 69 Japanese municipalities with sewage sludge incineration facilities. Selenium content in bag filter ash and ceramic filter ash was relatively higher than that in ash of cyclone and electrostatic precipitators. It was assumed that selenium vaporized in the furnace was due to adsorb in the fly ash on filter when passing through the low-temperature filter. To reduce high boiling point heavy metals in the ash, sewage sludge and incineration ash were heated up using a small muffle furnace. As the result, the chrome and nickel contents were reduced. A decrease in the surface area of ash and the reduction of elements occurred at the same time in sewage sludge and incineration ashes tested in this study.     

Critical evaluation of the use of the hydroxyapatite as a stabilizing agent to reduce the mobility of Zn and Ni in sewage sludge amended soils

The leachability of zinc (Zn) and nickel (Ni) was investigated in various soil types amended with sewage sludge and sewage sludge treated with hydroxyapatite. Sandy, clay and peat soils were investigated. For leachability tests, plastic columns (diameter 9 cm, height 50 cm) were filled with moist samples up to a height of 25 cm. Sewage sludge (1 kg) was mixed with 4.6 kg of clay and sandy soils and with 6.7 kg of peat soil. For sewage sludge mixtures treated with hydroxyapatite, 0.5 kg of the hydroxyapatite was added to 1 kg of the sewage sludge. Neutral (pH 7) and acid precipitation (pH 3.5) were applied. Acid precipitation was prepared from concentrated HNO(3), H(2)SO(4) and fresh doubly distilled water. The amount of precipitation corresponded to the average annual precipitation for the city of Ljubljana, Slovenia. It was divided into eight equal portions and applied sequentially on the top of the columns. The results indicated that the leachabilities of Zn in sewage sludge amended peat and clay soils were low (below 0.3% of total Zn content) and of Ni in sewage sludge amended sandy, clay and peat soil below 1.9% of total Ni content. In sewage sludge amended sandy soil, the leachability of Zn was higher (11% of Zn content). The pH of precipitation had no influence on the leachability of either metal. Treatment of sewage sludge with hydroxyapatite efficiently reduced the leachability of Zn in sewage sludge amended sandy soil (from 11% to 0.2% of total Zn content). In clay and peat sewage sludge amended soils, soil characteristics rather than hydroxyapatite treatment dominate Zn mobility.     

Combustion kinetics of sewage sludge and combustible wastes

This study estimated the kinetics of the mono- and co-combustion of sewage sludge pellets and combustible wastes such as municipal solid waste (MSW) and refuse-derived fuel (RDF). Sewage sludge was manufactured into pellets with a diameter of 8, 12, or 16 mm and a length of 30 mm. The RDF was composed of paper and plastics and was formed into pellets with a diameter of 8 mm and a length of 30 mm. MSW samples were synthesized using combustible wastes such as garbage, paper, plastics, and wood. The MSW was adjusted to have a moisture content of around 40% after shredding to under 10 mm. A laboratory-scale batch type stoker incinerator was used for the combustion and the gas composition of the flue gas was measured. The activation energy was calculated using the experimental results, and then the relation of the decomposition rate and reaction time was evaluated using the shrinking core model. The decomposition rate of the sludge pellets decreased as their diameter and moisture content increased, and the co-combustion of sludge pellets and combustible waste was affected by the amount of combustible waste. The individual combustion rates of the cylindrical sludge pellets or RDF were mainly controlled by the chemical reaction, but in the case of shredded MSW it was mostly influenced by gas diffusion. The rate for the co-combustion of sludge pellets and combustible wastes was mainly determined by the combustion rate of the combustible waste. The activation energy of the 8-mm-diameter sludge pellets was between 6.70 and 10.0 kcal/mol, according to the moisture content, but it was lower for MSW and RDF. In the case of MSW co-combustion, the reaction rate accelerated as the moisture content of the sludge pellets decreased, but it was markedly increased by the addition of RDF, regardless of the sludge moisture content.     

Lightweight aggregate made from sewage sludge and incinerated ash

In this study, sewage sludge ash (SSA), with similar characteristics to expansive clay, was used as the principal material and sewage sludge (SS) as the admixture to sinter lightweight aggregate and to study the influences of raw material composition on pelletising, sintering effect and aggregate properties. Results showed that both SS and SSA could be sintered to produce synthetic aggregates individually or mixed. Increasing the amount of SS would decrease the pelletising ratio. Under the consideration of energy saving, the mixture of SSA was better for sintering normal weight aggregate. On the contrary, the mixture that added 20-30% of SS was more adequate to make lightweight aggregates. Adding SS would enhance the oxidation-reduction reaction and lower the bulk density and sintering temperature of aggregates to save energy. Sintering temperature affected the properties of sewage sludge ash lightweight aggregate (SSALA) more than retention period did. Prolonging the retention period could improve bloating effect.     

Sewage sludge ash to phosphorus fertiliser (II): Influences of ash and granulate type on heavy metal removal

Ashes from monoincineration of sewage sludge suggest themselves as an ideal base for inorganic fertiliser production due to their relatively high phosphorus (P)-content. However, previously they need to be detoxified by reducing their heavy metal content. The core process considered in this paper consists of three steps: mixing of the ashes with suitable chlorine-containing additives, granulation of the mixture and thermochemical treatment in a rotary kiln. Here relevant heavy metal compounds are first transformed into volatile species with the help of the additives and then evaporated from the granules.In this study two chemically different ashes and their mixture were agglomerated to two different granulate types, briquettes and rolled pellets. The resulting six different materials were subjected to thermal treatment at different temperatures. The heavy metals examined were Cu and Zn due to their strong dependence on treatment conditions and their relevance concerning thermal treatment of sewage sludge ashes. Besides, the behaviour of Cl and K was monitored and evaluated.The experiments showed that ash type and temperature are more influential on Cl and heavy metal chemistry than granulate type. Temperature is a primary variable for controlling removal in both cases. Cu removal was less dependent on both ash and granulate type than Zn. The Cl utilization was more effective for Cu than for Zn. Depending on the treatment conditions some K could be retained, whereas always all P remained in the treated material. This satisfies the requirement for complete P recycling.     

Waste paper and clinoptilolite as a bulking material with dewatered anaerobically stabilized primary sewage sludge (DASPSS) for compost production

Environmental problems associated with sewage sludge disposal have prompted strict legislative actions over the past few years. At the same time, the upgrading and expansion of wastewater treatment plants have greatly increased the volume of sludge generated. The major limitation of land application of sewage sludge compost is the potential for high heavy metal content in relation to the metal content of the original sludge. Composting of sewage sludge with natural zeolite (clinoptilolite) can enhance its quality and suitability for agricultural use. However, the dewatered anaerobically stabilized primary sewage sludge (DASPSS) contained a low concentration of humic substances (almost 2%), and the addition of the waste paper was necessary in order to produce a good soil conditioner with high concentrations of humics. The final results showed that the compost produced from DASPSS and 40-50% w/w of waste paper was a good soil fertilizer. Finally, in order to estimate the metal leachability of the final compost product, the generalized acid neutralization Capacity (GANC) procedure was used, and it was found that by increasing the leachate pH, the heavy metal concentration decreased. The application of the sequential chemical extraction indicated that metals were bound to the residual fraction characterized as a stabilize fractions.     

Hybrid cement-assisted dewatering,solidification and stabilization of sewage sludge with high organic content

Sewage sludge with high organic content is particularly difficult to dewater before disposal in landfill. In this study, different hybrid cement binders were investigated to evaluate their ability to dewater the sewage sludge with high organic content. After 7 days of stabilization, the CASC (Mayenite/Sulfoaluminate cement) hybrid binder showed an excellent efficiency on both water content reduction and strength development; the water content and unconfined compressive strength value of solidified sludge reached 52.43 % and 109.55 kPa, respectively, at 8 % binder/sludge mass rate. The horizontal vibration leaching test (HJ 557-2009) indicated that leachability of heavy metals of the CASC-solidified sludge was far lower than that of non-solidified sludge and CAPC-solidified sludge. Furthermore, SEM and XRD analyses suggested that certain hydrates formed in the solidification process might have accelerated the depletion of interstitial water and strength development in the CASC-solidified sludge.     

Moisture retention of municipal solid waste mixed with sewage sludge and ash in a semi-arid climate.

Mechanisms involved in moisture storage in refuse are explored using data from four sets of experiments in a semi-arid climate. Two laboratory series of experiments contained municipal solid waste (MSW) amended with sewage sludge, one with higher proportions of ash in the MSW than the other. Outdoor experiments contained waste streams with different proportions of ash. Field cells compared moisture retention of refuse and MSW co-disposed with sewage sludge. Sewage sludge at high loads was found to increase the moisture storage relative to unamended MSW. Belt-pressed sludge retained water as bound water that was released by decay and changing pH. Sun-dried sludge also retained more moisture than MSW alone. In gravimetric terms, ash reduced the storage potential of MSW, in laboratory and outdoor experiments. However, outdoor experiments released less leachate from ash-rich refuse than middle-income waste with no ash fraction.     

Stabilization/solidification of MSW incineration residues from facilities with different air pollution control systems. Durability of matrices versus carbonation

This paper discusses the stabilisation/solidification process with Portland cement applied to municipal solid waste incineration residues. Two types of residues were considered: fly ash (FA) produced in an electrostatic precipitator, and air pollution control (APC) residues from a semi-dry scrubber process. Cement pastes with different percentages of FA and APC residues were characterised according to their physical properties, the effect of the hydration products and their leaching behaviour. Portland pastes prepared with APC residues showed a rapid setting velocity in comparison with setting time for those pastes substituted with FA residues. Portland cement hydration was retarded in FA pastes. Leaching test results showed that heavy metals (such as Zn, Pb and Cd) and sulphates are immobilised within the paste, whereas chlorides are only partially retained. The carbonation process increases the leachability of S04(2-) and heavy metals such as Zn and Cr.     

Gasification and its emission characteristics for dried sewage sludge utilizing a fluidized bed gasifier

Various research has attempted to determine the proper treatment of sewage sludge, including thermal technologies. Efficient thermal technologies have been focused on because of their energy saving/energy recovery. Gasification technology can be considered one of these approaches. In this study, the characteristics of gasification reactions were investigated with the aim of finding fundamental data for utilizing sewage sludge as an energy source. For the experiments on sewage sludge gasification reaction characteristics, a laboratory-scale experimental apparatus was set up with a fluidizing bed reactor of 70-mm inner diameter and 600-mm total height using an electric muffle furnace. The experimental materials were prepared from a sewage treatment plant located in Seoul. The reaction temperature was varied from 630 to 860°C, and the equivalence ratio from 0.1 to 0.3. The gas yields, compositions of product gas, and cold gas efficiencies of product gas were analyzed by GC/TCD and GC/FID installed with a carboxen-1000 column. The experimental results indicated that 800°C, ER 0.2 was an optimum condition for sewage sludge gasification. The maximum yield of product gas was about 44%. Producer gas from experiments was mainly composed of hydrogen, carbon monoxide, carbon dioxide, and methane. The cold gas efficiency of sewage sludge gasification was about 68%. The H₂/CO ratio and CO/CO₂ ratio were about 1.1 and 1.4, respectively, in optimum reaction conditions. Gaseous pollutants such as SO₂, HCl, NH₃, H₂S, and NO₂ were also analyzed at various gasification/combustion conditions, and their gaseous products were compared, showing significantly different oxidized product distributions.     

Effects of cement on redistribution of trace metals and dissolution of organics in sewage sludge and its inorganic waste-amended products

The suitability of using cement-stabilized sludge products as artificial soils in earth works was evaluated. The sludge products investigated were cemented sludge, cement-treated clay-amended sludge (SS+MC), and cement-treated copper slag-amended sludge (SS+CS). The leachability of lead (Pb), zinc (Zn), copper (Cu), and chromium (Cr) were assessed using the sequential extraction technique, toxicity characteristic leaching procedure (TCLP), NEN 7341 availability test, and column leaching test. The results indicated that Zn leachability was reduced in all the cement-stabilized sludge products. In contrast, Cu was transferred from the organic fraction to the readily leachable phases in the cement-stabilized sludge products and therefore exhibited increased leachability. The increased Cu leachability could be attributed to dissolution of humic substances in the sludge as a result of elevated pH. Good correlation between dissolved organic carbon (DOC) and heavy metal leaching from the cement-stabilized sludge products was observed in the column leaching experiment. Even with a cement percentage as small as 12.5%, calcium silicate hydrate (C-S-H) was formed in the SS+MC and SS+CS products. Inclusion of the marine clay in the SS+MC products could reduce the leaching potentials of Zn, and this was the great advantage of the marine clay over the copper slag for sludge amendment.     

Gasification characteristics of sewage sludge combined with wood biomass

The gas products from gasification processes have been considered to have some limitations in gas composition and heating value from the previous studies. Gasification characteristics of sewage sludge and wood mixture were investigated using different mixing ratios with the purpose of better quality of gas product suitable for energy/power generation. The gasification experiment was performed by an indirectly heated fluidized bed reactor. As reaction temperature increased from 600 to 900 °C, the yield of gas product increased with higher generation of CO, H₂ and CH₄ by more activated gas conversion reactions. As the equivalence ratio increased from 0.2 to 0.4, composition ratio of CO₂ increased while CO, CH₄, H₂ decreased as expected. Several operating variables including mixing ratio of wood with dried sludge were also tested. From this initial stage of experiment, optimal operating conditions for the bubbling fluidized bed gasifier, could be considered 900 °C in temperature; 0.2 in equivalence ratio and 40 % in wood mixing ratio within test variables range. These results will be more thoroughly investigated for the application to the larger scale pilot system.     

Extractability and leachability of heavy metals in Technosols prepared from mixtures of unconsolidated wastes

Mixtures of wastes were prepared to improve on the characteristics of the individual ingredients as Technosols, with special attention given to heavy metal extractability. An anaerobic digested sewage sludge and a CaO-treated aerobic sludge were used. A mixture of the two sludges (50:50 DW basis) was also prepared to provide a third type of sludge. The residues were mixed with other types of waste, such as fly ash, Linz-Donowitz slag, foundry sand, shot blasting machine scrap, fettling and barley straw. Extractability of Cu, Cr, Ni, and Zn by 0.01 M CaCl(2) extraction (Me(CACI(2)) was carried out, and leachability of these elements was estimated by acidification of an aqueous suspension of the mixtures with 0.5 N acetic acid (Me(acetic)). The total concentrations of the metals were also determined (Me(T)). The Me(CACI(2)/Me(T) ratios for Cu and Ni (means: 4.0% and 3.1%) were higher than those for Cr and Zn (means: 0.07% each). The mean Me(acetic)/Me(T) ratios followed the order Ni, Zn, Cu, and Cr (19.5%, 4.1%, 3.7%, and 0.09%, respectively). The results highlight the existence of complex interactions among organic matter solubility, pH and heavy metal extractability.     

Influence of calcium chloride on the thermal behavior of heavy and alkali metals in sewage sludge incineration

In order to separate and reuse heavy and alkali metals from flue gas during sewage sludge incineration, experiments were carried out in a pilot incinerator. The experimental results show that most of the heavy and alkali metals form condensed phase at temperature above 600 degrees C. With the addition of 5% calcium chloride into sewage sludge, the gas/solid transformation temperature of part of the metals (As, Cu, Mg and Na) is evidently decreased due to the formation of chloride, while calcium chloride seems to have no significant influence on Zn and P. Moreover, the mass fractions of some heavy and alkali metals in the collected fly ash are relatively high. For example, the mass fractions for Pb and Cu in the fly ash collected by the filter are 1.19% and 19.7%, respectively, which are well above those in lead and copper ores. In the case of adding 5% calcium chloride, the heavy and alkali metals can be divided into three groups based on their conversion temperature: Group A that includes Na, Zn, K, Mg and P, which are converted into condensed phase above 600 degrees C; Group B that includes Pb and Cu which solidify when the temperature is above 400 degrees C; and Group C that includes As, whose condensation temperature is as low as 300 degrees C.     

The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed

Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.     

Environmental and economic life cycle assessment for sewage sludge treatment processes in Japan

Life cycle assessment for sewage sludge treatment was carried out by estimating the environmental and economic impacts of the six alternative scenarios most often used in Japan: dewatering, composting, drying, incineration, incinerated ash melting and dewatered sludge melting, each with or without digestion. Three end-of-life treatments were also studied: landfilling, agricultural application and building material application. The results demonstrate that sewage sludge digestion can reduce the environmental load and cost through reduced dry matter volume. The global warming potential (GWP) generated from incineration and melting processes can be significantly reduced through the reuse of waste heat for electricity and/or heat generation. Equipment production in scenarios except dewatering has an important effect on GWP, whereas the contribution of construction is negligible. In addition, the results show that the dewatering scenario has the highest impact on land use and cost, the drying scenario has the highest impact on GWP and acidification, and the incinerated ash melting scenario has the highest impact on human toxicity due to re-emissions of heavy metals from incinerated ash in the melting unit process. On the contrary, the dewatering, composting and incineration scenarios generate the lowest impact on human toxicity, land use and acidification, respectively, and the incinerated ash melting scenario has the lowest impact on GWP and cost. Heavy metals released from atmospheric effluents generated the highest human toxicity impact, with the effect of dioxin emissions being significantly lower. This study proved that the dewatered sludge melting scenario is an environmentally optimal and economically affordable method.     

Landfilling characteristics of flue gas desulphurizing wastes

Leachate from mixtures of fly ash and flue gas desulphurizing (FGD) residues were analysed by shake and column tests. The pozzolanic reaction between FGD and fly ash proceeds over a period of several months forming a dense structure with reduced leachability. High variations were found between different sources of ash and FGD.     

污泥热解气化技术的研究进展

通过热解气化等热化学转化方式将污泥转变为液体或气体燃料是极具前景的污泥利用方式之一。从污泥的资源化利用方面着手,阐述了污泥热解气化技术的研究进展,分析了现有污泥热解气化工艺的优缺点和主要影响因素,并对该技术的发展趋势进行了展望。指出:高湿污泥与生物质混合进行共热解可以提高原料的转化率和整个系统的热效率;高效污泥热解气化装置的研发是目前污泥热解气化技术领域亟待解决的问题。