氨吹脱处理稀土分离厂中氨氮废水试验研究

稀土分离厂排放大量含氩氮废水,为了使该类废水能得到有效的处理,对稀土废水中中等浓度的氨氮废水进行了氨吹脱试验研究.发现pH、温度和气液比是氨氮去除效率高低的关键因素,废水初始浓度对去除率无影响.调节废水pH＝12,气液比在3 000～4 000,温度在35-45℃范围,浓度为1 570 mg/L的碳铵沉淀洗涤废水经氨吹脱处理可使出水残余氨氮浓度控制在100 mg/L以下,去除率达94%以上.     

超临界水氧化处理煤气化废水的响应面优化

采用响应面法对超临界水氧化处理煤气化废水的工艺参数进行了优化.运用中心复合设计,建立了COD、NH3-N去除率与温度、压强、氧化系数、反应时间4因素的二次回归模型,分析了各因素的显著性及交互作用.结果表明,各因素对COD、NH3-N去除率影响大小为:温度＞氧化系数＞反应时间＞压强.温度和氧化系数对COD去除率交互影响显著;温度和氧化系数、温度和反应时间、氧化系数和反应时间对NH3-N去除率交互影响显著.以COD、NH3-N去除率最大化,温度最低为目标条件,获得试验范围内最佳工艺条件:温度520℃,压强27.00 MPa,氧化系数3.0,反应时间10 min.该条件下3次验证试验的COD、NH3-N平均去除率分别为99.92％、99.54％,与预测值99.89％、99.51％无显著差异,表明所建模型切实可行.     

吹脱法预处理皮革废水的实验研究

对某皮革厂综合废水进行吹脱预处理实验,综合考察了影响氨氮去除的各个因素(pH值、汽液比、吹脱温度、氨氮初始浓度),同时对该预处理工艺去除铬、SS(悬浮固体浓度)、COD和硫化物的条件进行了优化,并进行了能耗及运行成本估算。结果表明:该厂皮革废水的最佳吹脱工况为pH=11,气液比=1 800,温度25~35℃,在此条件下,当进水ρ(NH3-N)=304.7 mg/L、ρ(Cr)=65.0 mg/L、ρ(SS)=1 700 mg/L、ρ(COD)=2 700 mg/L、ρ(S2-)=112.3 mg/L时,相应的去除率可达78.1%~83.5%、96.4%、88.2%、45.6%和85.0%,且吹脱法对氨氮具有较高的抗冲击负荷能力,吨水处理成本约为3.61元,可作为皮革废水的预处理工艺。     

超声波吹脱技术处理高浓度氨氮废水试验研究

采用超声波吹脱技术对高浓度NH3－N废水进行了处理试验。试验结果表明,废水采用超声波辐射以后,NH3－N的吹脱效果明显增加,与传统吹脱技术相比,NH3-N的去除率增加了17％－164％。经超声吹脱处理后的废水,NH3－N完全可以达到国家排放标准。     

氧化铁红生产中氨的回收及循环利用

利用吹脱工艺处理水热法制备氧化铁红产生的高浓度氨氮废水。经试验所得最佳的吹脱工艺参数为pH=12、CaO浓度30%、吹脱温度100℃和负压吹脱30 min。在此条件下,氨的回收利用率可达97.40%。用硫酸铁溶液吸收吹脱后氨水,使得氨得到了循环利用。水热实验证明回收的氨水并不影响氧化铁红产品的质量。     

生物增效结合SBR-AO处理垃圾渗滤液

在渗滤液处理现场进行了生物增效结合SBR-AO处理垃圾渗滤液的中试实验,对试验各段和整体工艺的运行条件和处理能力进行了测试分析:SBR段经过生物增效后,对NH3-N和BOD5的去除率分别达到89.0%和80.8%,明显优于未增效前的去除率。AO段试验结果显示,O池DO达到3.0 mg/L以上,经过生物增效可达最大NH3-N去除能力;A池硝化液回流比R值达到1.2时,系统的脱氮能力最大,而R值在0.4之内时,系统的去除COD能力达到最大。整体运行结果显示,当SBR-AO系统以脱氮为目的,系统对NH3-N的去除率可达98.8%,对TN的去除率可达82.6%;当SBR-AO系统以去除COD为目的,BOD5去除率可达94.0%,COD的去除率68.0%。     

沸石曝气生物滤池去除氨氮性能及生物学特征分析

天然沸石具有较大的孔隙率和比表面积,对氨氮有较强的选择性离子交换能力.运用天然沸石曝气生物滤池处理城市污水厂二级生化出水,结果表明,曝气生物滤池有良好的去除效果.在气水比为3∶1,水力负荷为1 m/h,温度＞20℃情况下,沸石曝气生物滤池对城市污水厂二级生化出水COD去除率为12.7%,NH3-N去除率为96.6%;试验系统沿程微生物活性和微生物量呈现逐渐下降趋势,而单位生物量的生物活性沿程分布则与此相反;曝气生物滤池对水中污染物的去除主要集中在底部进水端部分,当水流达到距进水端上方105 cm时,曝气生物滤池对水中NH3-N的去除率已达86.8%(占氨氮总去除率的90%),COD的去除率为13.3%(占COD总去除率的67%).     

纳米复合脱氮剂/气动超声吹脱高浓度氨氮废水

在自制0.2 t/h气动超声吹脱实验装置中,通过自主研发的纳米复合脱氮剂(CT-601)与气动超声波的耦合作用,在不同氨氮初始浓度、吹脱时间、CT-601投加量、气液比等条件下对高浓度氨氮废水进行研究。结果发现,在常温下p H=11、气液比=900∶1、脱氮剂投加量为0.0848 g/L时,超声吹脱60 min,处理2 000 mg/L的模拟废水时,去除率可达到93%以上,处理浓度为2 156 mg/L的实际废水时,去除率达到90%以上,较普通吹脱法和超声吹脱法分别提高40%和10%。同时还发现,该装置对COD去除率为29.72%,运行成本也只有7.24元/m3。     

硅酸钙微粉吸附预处理焦化废水中COD和NH3-N的实验研究

首次将固体废弃物硅酸钙微粉用于焦化废水的预处理,通过静态和动态吸附实验评价了硅酸钙微粉对COD和NH3-N的去除效果。结果表明:对COD和NH3-N产生吸附作用的有效组分为硅酸钙微粉的水解产物H2SiO3电离产生的HSiO3-和SiO23-;pH通过影响硅酸钙微粉水解反应以及水解产物H2SiO3和有机物、NH3的电离反应来影响去除率。在进水pH=7.00、硅酸钙微粉投加量为170g/L、振荡时间为75min的条件下,静态吸附实验中COD和NH3-N的去除率分别达16.1%和27.1%;经直径为10mm、高度为300mm的硅酸钙吸附柱预处理,动态吸附实验中COD和NH3-N的去除率分别可达58.9%和35.9%。     

吹脱法去除垃圾渗滤液中的氨氮研究

对吹脱法去除垃圾渗滤液中的氨氮进行了研究，控制吹脱效率高低的关键因素是温度、气液比和pH值。在水温大于25℃，气液比控制在3500左右，渗滤液pH值控制在10．5左右，对于氨氮浓度高达2000～4000mg／L的垃圾渗滤液，去除率可达到90％以上。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.