微波辐射Bi_2O_3/沸石-H_2O_2体系降解废水中的硝基苯

研究了微波辐射下,以负载于沸石上的三氧化二铋为催化剂,以双氧水为氧化剂的催化氧化体系处理硝基苯工艺。通过单因素实验法,从反应催化剂负载量、pH、双氧水用量、微波功率、反应时间、催化剂用量等方面初步考察了硝基苯在该体系中的催化氧化效果。在氧化铋负载量3%(质量比),pH=2,2 mL 30%双氧水,火力为中火,催化剂投加量为0.7 g,反应2 m in,对降解过程所得的中间产物和终产物进行了分析。结果表明,该体系对硝基苯的去除率能够达到99.2%,COD去除率为73.91%。     

碱减量-印染混合废水的预处理研究

针对碱度大、COD高、组成复杂的碱减量-印染混合废水,采用高碱度下直接混凝再酸析相结合的方法进行预处理,取得理想效果.试验结果表明,在高碱度条件下先加入镁盐及少量高分子絮凝剂,可去除大部分可溶性及不溶性污染物;再通过降低pH的酸析法,能有效去除废水中的色度、浊度,大大降低COD.在MgSO4用量为800～1 500 mg/L,阴离子聚丙烯酰胺用量为2 mg/L,酸析pH小于3.0时,色度去除率达97%,COD去除率达92%,浊度去除率近100%.     

催化湿式氧化农药废水及催化剂的研究

通过浸渍法制备了4种氧化物为主活性组分的负载固定型催化剂,用于过氧化氢催化湿式氧化(CWHPO)处理有机农药废水。用实验确定了催化湿式氧化的条件,不同催化剂处理效果的比较表明,四元组合MnO2CuOCeO2CoO催化剂性能较好,当反应在常温常压下,维持pH=7～9,反应时间为40min时,COD的去除率大于80%,色度去除率大于90%。     

催化湿式氧化技术处理山梨酸生产废水的研究

采用催化湿式氧化技术处理生产山梨酸过程中产生的高浓度有机废水,对催化剂组分进行优选.对反应温度、O2分压(Po2)和废水pH等工艺条件进行考察.实验结果表明:采用自制CuO-Cr2O3-La2O3/TiO2为复合催化剂处理该有机废水时表现出较好的催化活性;在190℃、Po2=2.1 MPa、pH=6.1、COD=10 030.0 mg/L时,反应90 min的COD去除率达到98.3%,而在相同条件下未加催化剂的湿式氧化的COD去除率只有60.1%.     

絮凝-Fenton试剂氧化处理印染废水

采用Fenton试剂对某染袜厂2种印染废水(印染红和印染蓝)进行处理。考察了硫酸亚铁投加量、双氧水投加量、反应时间及pH值对印染废水的色度及COD去除率的影响,通过正交实验确定了Fenton试剂处理该废水的最佳操作条件为:反应时间30 min、双氧水(30%)投加量4 mL/L、硫酸亚铁投加量300 mg/L、pH值为4左右。在最佳条件下,印染蓝废水经氧化处理后COD去除率大于80%,色度去除率95%以上;印染红废水需经絮凝预处理后再用Fenton试剂氧化处理,其脱色率达到了99.6%,COD去除率为91.2%,出水COD浓度为96 mg/L,可达标排放。     

微波辐射Bi2O3/沸石-H2O2体系降解废水中的硝基苯

研究了微波辐射下,以负载于沸石上的三氧化二铋为催化剂,以双氧水为氧化剂的催化氧化体系处理硝基苯工艺。通过单因素实验法,从反应催化剂负载量、pH、双氧水用量、微波功率、反应时间、催化剂用量等方面初步考察了硝基苯在该体系中的催化氧化效果。在氧化铋负载量3%（质量比）,pH=2,2 mL 30%双氧水,火力为中火,催化剂投加量为0.7 g,反应2 min,对降解过程所得的中间产物和终产物进行了分析。结果表明,该体系对硝基苯的去除率能够达到99.2%,COD去除率为73.91%。     

微波辐射Bi2O3/沸石-H2O2体系降解废水中的硝基苯

研究了微波辐射下,以负载于沸石上的三氧化二铋为催化剂,以双氧水为氧化剂的催化氧化体系处理硝基苯工艺。通过单因素实验法,从反应催化剂负载量、pH、双氧水用量、微波功率、反应时间、催化剂用量等方面初步考察了硝基苯在该体系中的催化氧化效果。在氧化铋负载量3%（质量比）,pH=2,2 mL 30%双氧水,火力为中火,催化剂投加量为0.7 g,反应2 m in,对降解过程所得的中间产物和终产物进行了分析。结果表明,该体系对硝基苯的去除率能够达到99.2%,COD去除率为73.91%。     

催化湿式氧化法处理吡虫啉农药废水的优化工艺条件

采用催化湿式氧化技术在2 L高压反应釜中处理吡虫啉农药废水,分别以复合金属氧化物Cu/Mn、Cu/Ce、Ce/Mn及Ce/Ag为催化剂来考察对废水COD去除率的影响.发现Cu/Ce、Ce/Mn、Cu/Mn催化剂有较高的催化活性;Ce/Mn催化剂最稳定;Ce/Ag催化剂的Ag溶出量很大.选用性能良好的Ce/Mn催化剂,考察了反应温度、反应压力和废水的初始pH对催化湿式氧化效果的影响.结果表明,催化剂的加入可使COD去除率提高37%左右,同时处理后废水的BOD5/COD从0.19提高到0.65以上;当反应温度为150～230 ℃时,处理效率随温度升高明显增加;总压4.8 MPa、氧分压1.2～2.4 MPa时,适当增加氧分压亦能提高氧化效率;废水初始pH对氧化效果影响不大,但对催化剂的稳定性有影响.优化工艺条件最终为:催化剂为Ce/Mn;温度190 ℃;氧分压1.6 MPa;进水pH为6.21;反应时间120 min.     

纳米RuO2-TiO2光电催化处理农药废水研究

采用自制的负载型纳米RuO2-TiO2光催化剂对农药厂生产废水进行光电催化降解试验.考察了煅烧时间、催化剂用量、光辐照强度、电流密度、废水初始pH值和反应时间对废水COD和色度去除率的影响.结果表明,自制光催化剂光电催化性能显著,最佳光电催化活性是同样降解条件下、同样含量的Degussa P-25 TiO2的1.38倍,是Ru0.3Ti07O2的1.81倍.其COD和色度去除率分别为64.3%和95.2%.     

催化臭氧氧化降解糖蜜酒精废水的研究

以SnO2为催化剂,研究糖蜜酒精废水在臭氧条件下的氧化降解反应,为糖蜜酒精废水的治理提供一种新的处理方法.研究表明,SnO2加速了臭氧氧化反应,使糖蜜酒精废水的氧化降解加快.影响糖蜜酒精废水氧化降解的主要因素有臭氧流量、废水的初始pH和催化剂用量等.加大臭氧流量及增加催化剂用量,均有利于糖蜜酒精废水的降解.适宜的反应条件是:糖蜜酒精废水的稀释倍数为10倍,臭氧流量为130 mg/h,催化剂用量为2.500 g/L,废水的初始pH为4.25,温度为30 ℃.在该条件下反应60 min,废水的脱色率为60.2%,COD去除率为44.5%.动力学分析表明,单独臭氧氧化降解糖蜜酒精废水和SnO2催化臭氧氧化降解糖蜜酒精废水均为拟一级反应.     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.     

Biochemical interaction of six op delayed neurotoxicants with several neurotargets

Abstract

Five organophosphorous insecticides: Leptophos, EPN, Cyano‐fenphos, trichloronate and salithion proved to cause irreversible ataxia not only to chicken but also to mice and sheep. TOCP was included as a reference. Cyanofenphos blocked the catecholamine B‐receptor binding activity with ³H‐norepinephrine at a level similar to that of the specific inhibitor propranolol in the mouse heart preparation. In the lamb heart preparation, the B‐receptor was more sensitive to Leptophos, salithion and TOCP than to propranolol. The six compounds and their oxons were screened for their in‐vitro inhibition to monamine oxidase (MAO), acetyl cholinesterase (AChE) and neurotoxic esterase (NTE) in the brain of either mouse, lamb or chicken. It is believed that their AChE inhibition stands for their acute toxicity, while NTE inhibition is responsible for their paralytic ataxia.     

Phytoextraction of lead-contaminated soil using vetivergrass (<Emphasis Type="Italic">Vetiveria zizanioides</Emphasis> L.), cogongrass (<Emphasis Type="Italic">Imperata cylindrica</Emphasis> L.) and carabaograss (<Emphasis Type="Italic">Paspalum conjugatum</Emphasis> L.)

Background, Aims and Scope The global problem concerning contamination of the environment as a consequence of human activities is increasing. Most of the environmental contaminants are chemical by-products and heavy metals such as lead (Pb). Lead released into the environment makes its way into the air, soil and water. Lead contributes to a variety of health effects such as decline in mental, cognitive and physical health of the individual. An alternative way of reducing Pb concentration from the soil is through phytoremediation. Phytoremediation is an alternative method that uses plants to clean up a contaminated area. The objectives of this study were: (1) to determine the survival rate and vegetative characteristics of three grass species such as vetivergrass, cogongrass and carabaograss grown in soils with different Pb levels; and (2) to determine and compare the ability of the three grass species as potential phytoremediators in terms of Pb accumulation by plants. Methods The three test plants: vetivergrass (Vetiveria zizanioides L.); cogongrass (Imperata cylindrica L.); and carabaograss (Paspalum conjugatum L.) were grown in individual plastic bags containing soils with 75 mg kg⁻¹ (37.5 kg ha⁻¹) and 150 mg kg⁻¹ (75 kg ha⁻¹) of Pb, respectively. The Pb contents of the test plants and the soil were analyzed before and after experimental treatments using an atomic absorption spectrophotometer. This study was laid out following a 3 × 2 factorial experiment in a completely randomized design. Results On the vegetative characteristics of the test plants, vetivergrass registered the highest whole plant dry matter weight (33.85–39.39 Mg ha⁻¹). Carabaograss had the lowest herbage mass production of 4.12 Mg ha⁻¹ and 5.72 Mg ha⁻¹ from soils added with 75 and 150 mg Pb kg⁻¹, respectively. Vetivergrass also had the highest percent plant survival which meant it best tolerated the Pb contamination in soils. Vetivergrass registered the highest rate of Pb absorption (10.16 ± 2.81 mg kg⁻¹). This was followed by cogongrass (2.34 ± 0.52 mg kg⁻¹) and carabaograss with a mean Pb level of 0.49 ± 0.56 mg kg⁻¹. Levels of Pb among the three grasses (shoots + roots) did not vary significantly with the amount of Pb added (75 and 150 mg kg⁻¹) to the soil. Discussion Vetivergrass yielded the highest biomass; it also has the greatest amount of Pb absorbed (roots + shoots). This can be attributed to the highly extensive root system of vetivergrass with the presence of an enormous amount of root hairs. Extensive root system denotes more contact to nutrients in soils, therefore more likelihood of nutrient absorption and Pb uptake. The efficiency of plants as phytoremediators could be correlated with the plants’ total biomass. This implies that the higher the biomass, the greater the Pb uptake. Plants characteristically exhibit remarkable capacity to absorb what they need and exclude what they do not need. Some plants utilize exclusion mechanisms, where there is a reduced uptake by the roots or a restricted transport of the metals from root to shoots. Combination of high metal accumulation and high biomass production results in the most metal removal from the soil. Conclusions The present study indicated that vetivergrass possessed many beneficial characteristics to uptake Pb from contaminated soil. It was the most tolerant and could grow in soil contaminated with high Pb concentration. Cogongrass and carabaograss are also potential phytoremediators since they can absorb small amount of Pb in soils, although cogongrass is more tolerant to Pb-contaminated soil compared with carabaograss. The important implication of our findings is that vetivergrass can be used for phytoextraction on sites contaminated with high levels of heavy metals; particularly Pb. Recommendations and Perspectives High levels of Pb in localized areas are still a concern especially in urban areas with high levels of traffic, near Pb smelters, battery plants, or industrial facilities that burn fuel ending up in water and soils. The grasses used in the study, and particularly vetivergrass, can be used to phytoremediate urban soil with various contaminations by planting these grasses in lawns and public parks. ESS-Submission Editor: Dr. Willie Peijnenburg (wjgm.peijnenburg@rivm.nl)