Degradation of some biorecalcitrant pesticides by homogeneous and heterogeneous photocatalytic ozonation

Photo-Fenton/ozone (PhFO) and TiO2-photocatalysis/ozone (PhCO) coupled systems are used as advanced oxidation processes for the degradation of the following biorecalcitrant pesticides: alachlor, atrazine, chlorfenvinfos, diuron, isoproturon and pentachlorophenol. These organic compounds are considered Priority Hazardous Substances by the Water Framework Directive of the European Commission. The degradation process of the different pesticides, that occurs through oxidation of the organic molecules by means of their reaction with generated OH radical, follows a first and zero-order kinetics, when PhFO and PhCO are applied, respectively. These two Advanced Oxidation Processes, together with the traditional ozone+UV, have been used to investigate TOC reduction of the different pesticide aqueous solutions. The best results of pesticide mineralization are obtained when PhFO is applied; with the use of this advanced oxidation process the aqueous pesticide solutions become detoxyfied except in the case of atrazine and alachlor aqueous solutions for which no detoxification is achieved at the experimental conditions used in the work, at least after 2 and 3 h of treatment, respectively.     

光催化-臭氧氧化降解H酸的研究

采用光催化-臭氧氧化技术(催化膜/UV/O3)降解H酸.研究结果表明,光催化与臭氧氧化相结合具有明显的协同作用.实验进一步讨论了臭氧投加量、废水初始pH值和H酸初始浓度对光催化-臭氧氧化降解H酸的影响.降解后的H酸,萘环结构被破坏,可生化性提高.     

光催化-臭氧氧化降解H酸的研究

采用光催化一臭氧氧化技术（催化膜／UV／O3）降解H酸。研究结果表明，光催化与臭氧氧化相结合具有明显的协同作用。实验进一步讨论了臭氧投加量、废水初始pH值和H酸初始浓度对光催化一臭氧氧化降解H酸的影响。降解后的H酸，萘环结构被破坏，可生化性提高。     

Degradation of industrial surfactants by photocatalysis combined with ozonation

The efficiency of titanium dioxide-mediated photocatalytic degradation of pollutants can be enhanced by combination with another advanced oxidation procedure such as ozonation. Mineralization of hydroxy- and dihydroxybenzenesulfonate based on these methods, both individually and combined, was investigated by monitoring the total organic carbon content, sulfate concentration, pH, high-performance liquid chromatography as well as the absorption spectral changes. The mineralization efficiency of the combined procedure significantly exceeded the sum of those of the individual techniques. The comparison of the disappearance of the starting material and the formation of the sulfate ions indicates that desulfonation is not the primary step of the degradation. Moreover, in the case of the combined method, ring cleavage, and thus, partial mineralization can occur without desulfonation. Efficient degradation of other, widely used industrial surfactants, such as alkylbenzene sulfonates and alkyl ether sulfates, was also achieved by heterogeneous photocatalysis combined with ozonation, offering an applicable method for the removal of these pollutants.     

Degradation of nitrogen containing organic compounds by combined photocatalysis and ozonation

The combination of TiO2-assisted photocatalysis and ozonation in the degradation of nitrogen-containing substrates such as alkylamines, alkanolamines, heterocyclic and aromatic N-compounds has been investigated. A laboratory set-up was designed and the influence of the structure of the N-compound, the TiO2 and ozone concentration on the formation of breakdown products were examined. The experimental results showed that a considerable increase in the degradation efficiency of the N-compounds is obtained by a combination of photocatalysis and ozonation as compared to either ozonation or photocatalysis only. The mineralization of the model substances was monitored by measurements of the TOC and ion-chromatographic determinations of the formed NO2- and NO3-. The temporal changes of concentrations of breakdown products, such as NH4+, short chain alkyl- and alkanolamines were determined by single column ion chromatography (SCIC) and as well as by electrospray mass spectrometry (EI-MS).     

Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

臭氧催化氧化降解苯胺的机理

对臭氧单独氧化和臭氧催化氧化下的苯胺降解效率进行了比较,并通过液质联机分析了氧化过程中产物变化情况。实验结果表明,催化剂MnO2-CuO-CeO2/沸石的添加能有效地提高臭氧氧化苯胺的降解率,当苯胺初始浓度为200mg/L,反应20 min后,苯胺的去除率由原来的75%提高到89%;通过LC-MS分析,臭氧催化氧化苯胺降解过程中代谢产物依次为对亚胺醌、对苯醌、马来酸和草酸,并由此推断出了臭氧催化氧化降解苯胺的途径。     

臭氧氧化预处理难降解农药废水的研究

采用臭氧氧化技术预处理脲类农药生产废水,调节废水pH至弱碱,在此基础上考察废水臭氧氧化预处理的影响因素,得出最佳预处理条件：COD为200 mg/L,初始pH为11.3,臭氧投加量为14.2 mg/L。连续预处理180 min后,可生化性从0.12提高到0.58,说明该项技术可大大提高脲类农药废水的可生化性。     

臭氧高级氧化法降解生化尾水中喹啉

采用O_3、O_3/UV、O_3/H_2O_23种工艺对喹啉的去除、矿化效果,生化性提高及降解规律等方面进行了对比分析,结果表明,单独H_2O_2、单独UV不能有效地降解喹啉;单独O_3、O_3/H_2O_2对喹啉有一定的去除效果,但两者差别不大;反应时间为6 min时,喹啉去除率分别为78.7%和79%,反应30 min时,喹啉的矿化率为33.4%和38.2%;O_3/UV工艺明显优于前2种,在6 min内,喹啉基本降解完全,30 min矿化率超过90%;3种工艺的降解过程都很好地满足伪一级动力学规律,O_3/UV的表观反应速率常数(0.7204 min~(-1))大于单独O_3(0.2832 min~(-1))和O_3/H_2O_2(0.29 min~(-1))工艺的表观反应速率常数;采用O_3/UV工艺处理实际工业园区生化尾水,6 min内喹啉降解完全,30 min时,COD去除率为88%,TOC的去除率达到89%,UV254的去除率为96%,出水指标达到《城镇污水处理厂污染物综合排放标准》一级A标准。     

Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl^? increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl^? at total mineralization was detected when initial diuron concentration was 13.8 mg L^?1. For N species, the final concentrations of NO₃ ^? and NH₄ ⁺ after 60 min of reaction time were 0.28 and 0.19 mg L^?1, respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na₂CO₃, additive NaHCO₃ and additive H₂O₂ were all advantageous to improve the degradation efficiency of diuron.     

Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl(-) increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl(-) at total mineralization was detected when initial diuron concentration was 13.8 mg L(-1). For N species, the final concentrations of NO3(-) and NH4+ after 60 min of reaction time were 0.28 and 0.19 mg L(-1), respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na2CO3, additive NaHCO3 and additive H2O2 were all advantageous to improve the degradation efficiency of diuron.     

Degradation of recalcitrant organic matter in SAARB leachate by a combined process of coagulation and catalytic ozonation

Environmental Science and Pollution Research - A combined coagulation and γ-Al2O3 catalytic ozonation process was used to treat semi-aerobic aged refuse biofilter (SAARB) effluent from...     

臭氧氧化法处理反渗透浓缩垃圾渗滤液

采用臭氧氧化法处理经反渗透膜处理后的浓缩垃圾渗滤液,考察了反应时间、臭氧投量、pH和温度对COD,色度以及浓缩液中腐殖酸的去除影响,通过BOD₅/COD变化分析了臭氧氧化对浓缩液生化性的提高作用。结果表明：在pH 8.0,温度30℃,臭氧投量5 g/h,反应时间90 min的条件下,浓缩液的COD、色度以及浓缩液中腐殖酸的去除率分别达到67.6%、98.0%和86.1%, BOD₅/COD从0.008提升到0.26,生化性有很大提高。     

多相催化臭氧氧化技术处理染料废水生化出水

采用多相催化臭氧氧化技术对某染料废水一级好氧生化出水进行系统实验研究,考察该技术对废水COD、色度的去除能力,并探讨其提高废水可生化性的能力。结果表明：在最佳操作条件下,即臭氧投加量200 mg·L-1,接触时间20 min时,COD平均从647 mg·L-1降低到440 mg·L-1,臭氧化指数约等于1;进水色度2 000倍左右,色度去除率达95%以上;SOUR值平均提高至原水的4倍;毒性由65%左右降低至0%;GC-MS结果显示废水中苯胺类、挥发酚类和硝基苯类等有毒污染物几乎全部被去除。另外,对实验所用的自制催化剂（连续使用90 d）进行ICP、BET、SEM、EDS分析,其有效成分锰、铈基本无损耗,催化剂性能稳定。研究表明在废水处理一级生化阶段后增加多相催化臭氧技术,不仅能够进一步去除COD,还可以明显提高二级好氧生化脱氮能力,对于污水处理的升级改造具有重要意义。     

Degradation of reactive dyes I. A comparative study of ozonation, enzymatic and photochemical processes

The environmental problems associated with textile activities are represented mainly by the extensive use of organic dyes. A great number of these compounds are recalcitrant and shown carcinogenic or mutagenic character. In this work three processes were studied for degradation of an anthraquinone dye (C.I. reactive blue-19). The ozonation process leads to complete decolorization with a very short reaction time; however, effective mineralization of the dye was not observed. The enzymatic process promotes quick decolorization of the dye; nevertheless, maximum decolorization degrees of about 30% are insignificant in relation to the decolorization degree achieved by the other processes. The best results were found for the photocatalytical process. The use of ZnO or TiO2 as photocatalysts, permits total decolorization and mineralization of the dye with reaction times of about 60 min.     

The impact of material design on the photocatalytic removal efficiency and toxicity of two textile dyes

Environmental Science and Pollution Research - This study deals with the toxicity of the treated solutions of two types of dyes, namely, the anthraquinonic Reactive Bleu 19 dye (RB19) and the...     

Atrazine removal by ozonation processes in surface waters

Atrazine (6-chloro-N-ethyl-N'-isopropyl-1,3,5-triazinedyl-2,4-diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continuously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O3/H2O2 process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O3/H2O2 and O3/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Atrazine removal by ozonation processes in surface waters

Abstract

Atrazine (6‐chloro‐N‐ethyl‐N'‐isopropyl‐1,3,5‐triazinedyl‐2,4‐diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O₃/H₂O₂ process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O₃/H₂O₂ and O₃/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Degradation of atrazine by catalytic ozonation in the presence of iron scraps: performance,transformation pathway,and acute toxicity

Degradation of atrazine by catalytic ozonation in the presence of iron scraps (ZVI/O₃) was carried out. The key operational parameters (i.e., initial pH, ZVI dosage, and ozone dosage) were optimized by the batch experiments, respectively. This ZVI/O₃ system exhibited much higher degradation efficiency of atrazine than the single ozonation, ZVI, and traditional ZVI/O₂ systems. The result shows that the pseudo-first-order constant (0.0927?min^?1) and TOC removal rate (86.6%) obtained by the ZVI/O₃ process were much higher than those of the three control experiments. In addition, X-ray diffraction (XRD) analysis indicates that slight of γ-FeOOH and Fe₂O₃ were formed on the surface of iron scrap after ZVI/O₃ treatment. These corrosion products exhibit high catalytic ability for ozone decomposition, which could generate more hydroxyl radical (HO^?) to degrade atrazine. Six transformation intermediates were identified by liquid chromatography-mass spectrometry (LC-MS) analysis in ZVI/O₃ system, and the degradation pathway of atrazine was proposed. Toxicity tests based on the inhibition of the luminescence emitted by Photobacterium phosphoreum and Vibrio fischeri indicate the detoxification of atrazine by ZVI/O₃ system. Finally, reused experiments indicate the approving recyclability of iron scraps. Consequently, the ZVI/O₃ system could be as an effective and promising technology for pesticide wastewater treatment.     

NOM characteristics and treatabilities of ozonation processes

The objectives of this study were intended to evaluate the effects of the characteristics of natural organic matter on the treatabilities of ozonation, coagulation, filtration, and granular activated carbon processes. The ultra-violet absorbance (UV254) was used as a surrogate parameter to assess each process in reducing the disinfection by-product formation potential (DBPFP). The results indicate that the DBPFP varies with the sources of water samples and treatment processes, but is closely related to the measurement of UV254/DOC. Coagulation/sedimentation can eliminate large molecular weight organic fractions. Both pre- and post-ozonation processes can reduce some of DBP precursors than the conventional treatment process, and are more reliable for reducing the overall DBPFP.