Removal of anionic azo dye from aqueous solution via an adsorption–photosensitized regeneration process on a TiO2 surface

Textile dye effluents are typically characterized by strong color and recalcitrance, even at very low concentration. The process of enrichment of anionic azo dye on the surface of TiO₂ fibers followed by photosensitization degradation under ambient air conditions was extensively investigated. Adsorption isotherms and zeta potentials were used to describe the “dye/TiO₂ surface” interface, taking into account the effects of pH on the nature and population of the surface groups on the TiO₂ fibers. The extent of the photocatalytic degradation of dye on TiO₂ surface was determined by FTIR. N₂ adsorption isotherms and optical spectra were employed to investigate the effect of photosensitization. The adsorption of dyes on the TiO₂ surface occurs via electrostatic attraction through the formation of single- or multidentate-coordinated surface complexes. Almost complete photobleaching of the absorption band at 534 nm is achieved in ~4 h. Dye-sensitized TiO₂ fiber could absorb part of the visible light spectrum (λ?<?600 nm). Interfacial electron transfer can potentially alter the degradation efficiency. The regenerated TiO₂ fiber could be reused for subsequent decolorization without a decline in adsorption efficiency compared with freshly prepared TiO₂ samples, which may be attributed to preservation of the hierarchical pore structure and restoration of the original surface properties. In summary, we propose an efficient “adsorption–photoregeneration–reuse” process applying TiO₂ fibers for the degradation of dyes in water.     

Photocatalytic discoloration of Methyl Orange by anatase/schorl composite: optimization using response surface method

The anatase/schorl composites were prepared and employed for the photocatalytic discoloration of an azo dye, Methyl Orange (MO). X-ray diffraction results indicated that TiO₂ existed in the form of anatase phase and no diffraction peaks of schorl could be observed for all the composite samples. Scanning electron micrographs showed that the particles of anatase were well deposited and dispersed on the surface of schorl. Photocatalytic experiments revealed that the anatase/schorl composites exhibited higher photocatalytic activity for MO discoloration than pure TiO₂ and more than 90 % discoloration ratio could be obtained within 60 min UV irradiation when the sample containing 3 wt.% of schorl as TiO₂ support was used. Then, the central composite design (CCD) under the response surface methodology (RSM) was employed for the experiment design and process optimization. The significance of a second-order polynomial model for predicting the optimal values of MO discoloration was evaluated by the analysis of variance (ANOVA) and 3D response surface plots for the interactions between two variables were constructed. Based on the model prediction, the optimum conditions for the photocatalytic discoloration of MO by TiO₂/schorl composite were determined to be 15?×?10^?3 mM MO initial concentration, 2.7 g/l photocatalyst dosage, solution pH 6.6 and 43 min reaction time, with a maximum MO discoloration ratio of 98.6 %. Finally, a discoloration ratio of 94.3 % was achieved for the real sample under the optimum conditions, which was very close to the predicted value, implying that RSM is a powerful and satisfactory strategy for the process optimization.     

Titania-supported silver-based bimetallic nanoparticles as photocatalysts

Photocatalytic process has shown recently a great potential as an environmental friendly and clean remediation technology for organic pollutants in wastewater. This work described the synthesis of silver-based bimetallic nanoparticles using colloid chemistry and the subsequent immobilization onto titania to form composite photocatalytic materials (titania-supported Ag–Pt nanoparticles). The photocatalysts were characterized by X-ray diffraction, electron microscopy, and nitrogen physisorption. The catalytic activity of the photocatalysts was evaluated by photocatalytic degradation of phenol and 2-chlorophenol (2-CP) in synthetic wastewater solutions. The photocatalytic processes were conducted in a batch photoreactor containing appropriate solutions of phenol and 2-CP with UV irradiation of 450 W. UV-visible spectrophotometer was used for analyzing the concentration of phenol and 2-CP in solutions. Parameters affecting the photocatalytic process such as the solution pH, phenol and 2-CP concentrations, and catalyst concentration were investigated. The results obtained revealed that TiO₂-supported Ag/Pt nanoparticles showed a higher activity for UV-photocatalytic degradation of both phenol and 2-CP pollutants in the solution (as compared to the plain rutile TiO₂). The photodegradation processes were optimized by the 0.5-g/L catalyst with a pollutant concentration of 50 mg/L for all the samples. Complete degradation for both phenol and 2-CP was achieved after 120 min.     

Photocatalytic degradation of Reactive Red 195 using anatase/brookite TiO2 mesoporous nanoparticles: Optimization using response surface methodology (RSM) and kinetics studies

In the present study, the photocatalytic degradation of Reactive Red 195 (RR195) from aqueous samples under UV-A irradiation by using anatase/brookite TiO₂ (A/B TiO₂) mesoporous nanoparticles has been investigated. Batch experiments were conducted to study the effects of the main parameters affecting the photocatalytic process. The effects and interactions of most influenced parameters, such as substrate concentration and catalyst load, were evaluated and optimized by using a central composite design model and a response surface methodology. The results indicated that the dye degradation efficiency in the experimental domain investigated was mainly affected by the tested variables, as well as their interaction effects. Analysis of variance showed a high coefficient of determination value (R ²?=?0.9947), thus ensuring a satisfactory adjustment of the first-order regression model (2FI model) with the experimental data. The obtained results also indicate that catalyst loading plays an important role in determining the removal efficiency of RR195 attributable to both photodegradation and adsorption process. Under optimal conditions (initial dye concentration (50 mg/L) and catalyst loading (2,000 mg/L), A/B TiO₂ showed similar removal efficiency compared to that of commercial titania (Degussa P25). Also, at these conditions, complete degradation of RR195 can be achieved by both catalysts within 15 min under UV-A irradiation. The experiments demonstrated that dye removal on the prepared A/B TiO₂ was facilitated by the synergistic effects between adsorption and photocatalysis. Photocatalytic mineralization of RR195 was monitored by total organic carbon. The recycling experiments confirmed the stability of the catalyst.     

Adsorptive removal and photocatalytic decomposition of sulfamethazine in secondary effluent using TiO2–zeolite composites

We investigated the adsorption and decomposition of sulfamethazine (SMT), which is used as a synthetic antibacterial agent and discharged into environmental water, using high-silica Y-type zeolite (HSZ-385), titanium dioxide (TiO₂), and TiO₂–zeolite composites. By using ultrapure water and secondary effluent as solvents, we prepared SMT solutions (10 μg/L and 10 mg/L) and used them for adsorption and photocatalytic decomposition experiments. When HSZ-385 was used as an adsorbent, rapid adsorption of SMT in the secondary effluent was confirmed, and the adsorption reached equilibrium within 10 min. The photocatalytic decomposition rate using TiO₂ in the secondary effluent was lower than that in ultrapure water, and we clarified the inhibitory effect of ions and organic matter contained in the secondary effluent on the reaction. We synthesized TiO₂–zeolite composites and applied them to the removal of SMT. During the treatment of 10 μg/L SMT in the secondary effluent using the composites, 76 % and more than 99 % of the SMT were decomposed within 2 and 4 h by photocatalysis. The SMT was selectively adsorbed onto high-silica Y-type zeolite in the composites. Resultantly, the inhibitory effect of the coexisting materials was reduced, and the composites could remove SMT more effectively compared with TiO₂ alone in the secondary effluent.     

Electrosorption and photocatalytic one-stage combined process using a new type of nanosized TiO2/activated charcoal plate electrode

In the present study, an activated charcoal (AC) plate was prepared by physical activation method. Its surface was coated with TiO₂ nanoparticles by electrophoretic deposition (EPD) method. The average crystallite size of TiO₂ nanoparticles was determined approximately 28 nm. The nature of prepared electrode was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and Brunauer–Emmett–Teller (BET) surface area measurement before and after immobilization. The electrosorption and photocatalytic one-stage combined process was investigated in degradation of Lanasol Red 5B (LR5B), and the effect of dye concentration, electrolyte concentration, pH, voltage, and contact time was optimized and modeled using response surface methodology (RSM) approach. The dye concentration of 30 mg L^?1, Na₂SO₄ concentration of 4.38 g L^?1, pH of 4, voltage of 250 mV, and contact time of 120 min were determined as optimum conditions. Decolorization efficiency increased in combined process to 85.65 % at optimum conditions compared to 66.03 % in TiO₂/AC photocatalytic, 20.09 % in TiO₂/AC electrosorption, and 1.91 % in AC photocatalytic processes.     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.     

Adsorption and photocatalytic decomposition of roxarsone by TiO2 and its mechanism

Roxarsone (3-nitro-4-hydroxyphenylarsonic acid) has been widely used as organic arsenic additive in animal industry. In this study, the adsorption of roxarsone on TiO₂ under dark conditions, the photocatalytic decomposition of roxarsone under UV/TiO₂, and the possible photocatalytic pathway were investigated. At the initial concentration of 5–35 mg/L, the adsorption of roxarsone fitted well with the pseudo-second-order kinetics. The isotherms analysis showed that the Langmuir model was better than the Freundlich and Dubinin–Radushkevich models for describing the adsorption process. After 7 h of photocatalytic decomposition, a complete disappearance of roxarsone was achieved. The pH value has a significant effect on both adsorption and photocatalytic decomposition of roxarsone. The results of high-performance liquid chromatography-hydride generation-atomic fluorescence spectrometry (HPLC-HG-AFS) and gas chromatography-mass spectrometry (GC/MS) analyses proved the cleavage of the As-C bond during the photocatalytic decomposition process by TiO₂ and the intermediates of the decomposition. Based on the results, a possible photocatalytic decomposition pathway was proposed.     

Photocatalytic Degradation of the Herbicide Erioglaucine in the Presence of Nanosized Titanium Dioxide: Comparison and Modeling of Reaction Kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO₂ nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO₂ system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir–Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm^{? 1} and 0.984 ppm min^{? 1}, respectively. In this work, we also compared the reactivity between the commercial TiO₂ Degussa P-25 and a rutile TiO₂. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO₂ for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO₂ process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO₂.     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

Photocatalytic Degradation of an Organophosphorus Pesticide Phosalone in Aqueous Suspensions of Titanium Dioxide

Abstract

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO₂ particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. The half-life (DT₅₀) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K = 0.0532 min^?1). The half-life time of photomineralization in the concentration range of 7.5–20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

The enhancement of photodegradation efficiency using Pt–TiO2 catalyst

This study investigates the mechanism of photosensitization and the recombination of excited electron–hole pairs affected by depositing platinum (Pt) on the surface of titanium dioxide (TiO₂). A new catalyst of Pt–TiO₂ was prepared by a photoreduction process. Being model reactions, the photocatalytic oxidation of methylene blue (MB) and methyl orange (MO) in aqueous solutions using the Pt–TiO₂ catalyst was carried out under either UV or visible light irradiation. The experimental results indicate that an optimal content of 0.75%Pt–TiO₂ achieves the best photocatalytic performance of MB and MO degradation and that the Pt–TiO₂ catalyst can be sensitized by visible light. The interaction of Pt and TiO₂ was investigated by means of UV–Vis absorption spectra, photoluminescence emission spectra, and X-ray photoelectron emission spectroscopy. The Pt⁰, Pt²⁺ and Pt⁴⁺ species existing on the surface of Pt–TiO₂, and the Ti³⁺ species existing in its lattice may form a defect energy level. The Pt impurities, including Pt, Pt(OH)₂, and PtO₂, and the defect energy level absorb visible light more efficiently in comparison with the pure TiO₂ and hinder the recombination rate of excited electron–hole pairs.     

UV–visible light-activated Ag-decorated,monodisperse TiO2 aggregates for treatment of the pharmaceutical oxytetracycline

Noble metal Ag-decorated, monodisperse TiO₂ aggregates were successfully synthesized by an ionic strength-assisted, simple sol–gel method and were used for the photocatalytic degradation of the antibiotic oxytetracycline (OTC) under both UV and visible light (UV–visible light) irradiation. The synthesized samples were characterized by X-ray diffraction analysis (XRD); UV–vis diffuse reflectance spectroscopy; environmental scanning electron microscopy (ESEM); transmission electron microscopy (TEM); high-resolution TEM (HR-TEM); micro-Raman, energy-dispersive X-ray spectroscopy (EDS); and inductively coupled plasma optical emission spectrometry (ICP-OES). The results showed that the uniformity of TiO₂ aggregates was finely tuned by the sol–gel method, and Ag was well decorated on the monodisperse TiO₂ aggregates. The absorption of the samples in the visible light region increased with increasing Ag loading that was proportional to the amount of Ag precursor added in the solution over the tested concentration range. The Brunauer, Emmett, and Teller (The BET) surface area slightly decreased with increasing Ag loading on the TiO₂ aggregates. Ag-decorated TiO₂ samples demonstrated enhanced photocatalytic activity for the degradation of OTC under UV–visible light illumination compared to that of pure TiO₂. The sample containing 1.9 wt% Ag showed the highest photocatalytic activity for the degradation of OTC under both UV–visible light and visible light illumination. During the experiments, the detected Ag leaching for the best TiO₂-Ag photocatalyst was much lower than the National Secondary Drinking Water Regulation for Ag limit (0.1 mg L^?1) issued by the US Environmental Protection Agency.     

Photoassisted and photocatalytic degradation of sulfur mustard using TiO2 nanoparticles and polyoxometalates

The decomposition of highly toxic chemical warfare agent, sulfur mustard (bis(2-chloroethyl) sulfide or HD), has been studied by homogeneous photolysis and heterogeneous photocatalytic degradation on titania nanoparticles. Direct photolysis degradation of HD with irradiation system was investigated. The photocatalytic degradation of HD was investigated in the presence of TiO₂ nanoparticles and polyoxometalates embedded in titania nanoparticles in liquid phase at room temperature (33?±?2 °C). Degradation products during the treatment were identified by gas chromatography–mass spectrometry. Whereas apparent first-order kinetics of ultraviolet (UV) photolysis were slow (0.0091 min^?1), the highest degradation rate is obtained in the presence of TiO₂ nanoparticles as nanophotocatalyst. Simultaneous photolysis and photocatalysis under the full UV radiation leads to HD complete destruction in 3 h. No degradation products observed in the presence of nanophotocatalyst without irradiation in 3 h. It was found that up to 90 % of agent was decomposed under of UV irradiation without TiO₂, in 6 h. The decontamination mechanisms are often quite complex and multiple mechanisms can be operable such as hydrolysis, oxidation, and elimination. By simultaneously carrying out photolysis and photocatalysis in hexane, we have succeeded in achieving faster HD decontamination after 90 min with low catalyst loading. TiO₂ nanoparticles proved to be a superior photocatalyst under UV irradiation for HD decontamination.     

Photodegradation of gaseous acetaldehyde and methylene blue in aqueous solution with titanium dioxide-loaded activated carbon fiber polymer materials and aquatic plant ecotoxicity tests

TiO₂-supported activated carbon felts (TiO₂–ACFTs) were prepared by dip coating of felts composed of activated carbon fibers (ACFs) with either polyester fibers (PS-A20) and/or a polyethylene pulp (PE-W15) in a TiO₂ aqueous suspension followed by calcination at 250 °C for 1 h. The as-prepared TiO₂–ACFTs with 29–35 wt.% TiO₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and N₂ adsorption. The TiO₂–ACFT(PS-A20) samples with 0 and 29 wt.% TiO₂ were microporous with specific surface areas (S _BET) of 996 and 738 m²/g, respectively, whereas the TiO₂–ACFT(PE-W15) samples with 0 and 35 wt.% TiO₂ were mesoporous with S _BET of 826 and 586 m²/g, respectively. Adsorption and photocatalytic activity of the as-prepared samples were evaluated by measuring adsorption in the dark and photodegradation of gaseous acetaldehyde (AcH) and methylene blue (MB) in aqueous solution under UV light. The TiO₂ loading caused a considerable decrease in the S _BET and MB adsorption capacity along with an increase in MB photodegradation and AcH mineralization. Lemna minor was chosen as a representative aquatic plant for ecotoxicity tests measuring detoxification of water obtained from the MB photodegradation reaction with the TiO₂–ACFT samples under UV light.     

Effect of Nb doping on structural, optical and photocatalytic properties of flame-made TiO2 nanopowder

TiO₂:Nb nanopowders within a dopant concentration in the range of 0.1?C15?at.% were prepared by one-step flame spray synthesis. Effect of niobium doping on structural, optical and photocatalytic properties of titanium dioxide nanopowders was studied. Morphology and structure were investigated by means of Brunauer?CEmmett?CTeller isotherm, X-ray diffraction and transmission electron microscopy. Diffuse reflectance and the resulting band gap energy were determined by diffuse reflectance spectroscopy. Photocatalytic activity of the investigated nanopowders was revised for the photodecomposition of methylene blue (MB), methyl orange (MO) and 4-chlorophenol under UVA and VIS light irradiation. Commercial TiO₂-P25 nanopowder was used as a reference. The specific surface area of the powders was ranging from 42.9?m²/g for TiO₂:0.1?at.% Nb to 90.0?m²/g for TiO₂:15?at.% Nb. TiO₂:Nb particles were nanosized, spherically shaped and polycrystalline. Anatase was the predominant phase in all samples. The anatase-related transition was at 3.31?eV and rutile-related one at 3.14?eV. TiO₂:Nb nanopowders exhibited additional absorption in the visible range. In comparison to TiO₂-P25, improved photocatalytic activity of TiO₂:Nb was observed for the degradation of MB and MO under both UVA and VIS irradiation, where low doping level (Nb?<?1?at.%) was the most effective. Niobium doping affected structural, optical and photocatalytic properties of TiO₂. Low dopant level enhanced photocatalytic performance under UVA and VIS irradiation. Therefore, TiO₂:Nb (Nb?<?1?at.%) can be proposed as an efficient selective solar light photocatalyst.     

Fabrication of cerium titanate cellulose fiber nanocomposite materials for the removal of methyl orange and methylene blue from polluted water by photocatalytic degradation

In this study, cellulose fibers (Cf), extracted from sunflower seed husk, and different molar ratios of cerium titanate (Ce-Ti) NPs were prepared from sunflower seed husk extract by a green biosynthesis approach. Cf and Ce-Ti NPs were reacted via cross-linking reaction to synthesize a novel nanocomposite photocatalyst of Ce-Ti/Cf. Using Fourier-transform infrared (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM-EDX) spectroscopy, all manufactured materials were characterized. The results obtained from FTIR and EDX analyses indicated that Cf and its nanocomposites (0.1 Ce-Ti/Cf, 0.3 Ce-Ti/Cf, and 0.5 Ce-Ti/Cf) were successfully prepared by harnessing biomass extract from sunflower seed husk. Furthermore, XRD revealed that the degree of crystallinity of the nanocomposites was enhanced by increasing the molar ratios of the Ce-Ti NPs. The photocatalytic activity of as-fabricated 0.1 Ce-Ti/Cf, 0.3 Ce-Ti/Cf, and 0.5 Ce-Ti/Cf nanocomposite samples was investigated on methylene blue (MB) and methyl orange (MO) dyes as model organic compounds found in wastewaters. The effects of dose, contact time, and pH on the photocatalytic activity of the synthesized nanocomposites, the photodegradation kinetic parameters of MB, and MO degradation with/without the addition of H₂O₂ were also studied. The results revealed that high photodegradation efficiency could be obtained as the ratio of TiO₂ in the Ce-Ti nanocomposite formula increases. Moreover, after sunlight irradiation, the adsorption capacity and the dye decomposition ratio significantly increase during the early contact time and reach equilibrium at about 240 and 120 min for 0.5 Ce-Ti/Cf nanocomposite photocatalyst in the absence and presence of hydrogen peroxide, respectively. In light of the obtained results and the practical wastewater treatment study conducted, the prepared photocatalyst from Ce-Ti/Cf nanocomposites could be a promising material for treating dye wastewater especially collected from Egypt.

     

Adsorption behavior of light green anionic dye using cationic surfactant-modified wheat straw in batch and column mode

An agricultural by-product, natural wheat straw (NWS), was soaked in 1 % cationic surfactant (hexadecylpyridinium bromide, CPB) solution for 24 h (at 293 K), and modified wheat straw (MWS) was obtained. Analysis of FTIR, XFR, and nitrogen element showed that CPB was adsorbed onto surface of NWS. Then, MWS was used as adsorbent for the removal of light green dye (LG, anionic dye) from aqueous solution. The experiment was performed in batch and column mode at room temperature (293 K). Sodium chloride (up to 0.1 mol/L) existed in solution was not favor of LG dye adsorption. The equilibrium data were better described by Langmuir isotherm, and adsorption capacity of q _m from Langmuir model was 70.01?±?3.39 mg/g. In fixed-bed column adsorption mode, the effects of initial LG concentration (30, 50, 70 mg/L) and flow rate (6.5, 9.0, 14.5 mL/min) on adsorption were presented. Thomas and modified dose–response models were used to predict the breakthrough curves using nonlinear analysis method, and both models can fit the breakthrough curves. Theoretical and experimental breakthrough curves were drawn and compared. The results implied that MWS can be used as adsorbent material to remove LG from aqueous solution.     

Effective photodegradation of methomyl pesticide in concentrated solutions by novel enhancement of the photocatalytic activity of TiO2 using CdSO4 nanoparticles

Annihilation of electrons–holes recombination process is the main remedy to enhance the photocatalytic activity of the semiconductors photocatalysts. Doping of this class of photocatalysts by foreign nanoparticles is usually utilized to create high Schottky barrier that facilitates electron capture. In the literature, because nonpolar nanoparticles (usually pristine metals, e.g., Ag, Pt, Au, etc.) were utilized in the doping process, the corresponding improvement was relatively low. In this study, CdSO₄-doped TiO₂ nanoparticles are introduced as a powerful and reusable photocatalyst for the photocatalytic degradation of methomyl pesticide in concentrated aqueous solutions. The utilized CdSO₄ nanoparticles form polar grains in the TiO₂ matrix due to the electrons leaving characteristic of the sulfate anion. The introduced nanoparticles could successfully eliminate the harmful pesticide under the sunlight radiation within a very short time (less than 1 h), with a removal capacity reaching 1,000 mg pesticide per gram of the introduced photocatalyst. Moreover, increase in the initial concentration of the methomyl did not affect the photocatalytic performance; typically 300, 500, 1,000, and 2,000 mg/l solutions were completely treated within 30, 30, 40, and 60 min, respectively, using 100 mg catalyst. Interestingly, the photocatalytic efficiency was not affected upon multiple use of the photocatalyst. Moreover, negative activation energy was obtained which reveals super activity of the introduced photocatalyst. The distinct photocatalytic activity indicates the complete annihilation of the electrons–holes recombination process and abundant existence of electrons on the catalyst surfaces due to strong electrons capturing the operation of the utilized polar CdSO₄ nanoparticles. The introduced photocatalyst has been prepared using the sol–gel technique. Overall, the simplicity of the synthesizing procedure and the obtained featured photocatalytic activity strongly recommend the introduced nanoparticles to treat the methomyl-containing polluted water.     

碳纳米管/二氧化钛/壳聚糖催化薄膜光催化活性及苯降解机理

通过X-射线衍射仪(XRD)、扫描电镜(SEM)、透射电镜(TEM)和紫外可见光漫反射谱(UV-vis)对碳纳米管/二氧化钛/壳聚糖复合薄膜的晶体结构和形貌进行表征,以室内空气典型污染物气相苯为模型反应物,研究碳纳米管/二氧化钛/壳聚糖催化薄膜的光催化活性及其对苯的光降解机理。结果表明,制备的碳纳米管/二氧化钛/壳聚糖催化薄膜所具有的良好催化活性归功于碳纳米管、二氧化钛和壳聚糖三者的协调效应;气相苯光降解产生的主要中间产物是乙酸乙酯和十一烷,以及少量的丙烯醛、4-羰基-甲基-苯乙酮、十二烷烃、2,4,-二叔丁基苯酚、二十一烷烃。根据红外光谱分析与GC/MS分析结果,进一步提出了气相苯的降解机理过程。