腐殖酸树脂处理含Pb2+、CU2+、Ni2+废水的研究

利用泥炭为原料制备腐殖酸树脂.在动态条件下,研究了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附效果及吸附条件.同时探讨了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附与解吸再生机理,吸附机理研究表明,腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的主要吸附形式为离子交换吸附和络合吸附.结果表明,在废水pH值为5.0～7.0,Pb2+、Cu2+和Ni2+浓度分别为50 mg/L,经腐殖酸树脂处理,Pb2+、Cu2+和Ni2+去除率可达98%以上,且处理后废水近中性.含Pb2+、Cu2+和Ni2+电镀废水经腐殖酸树脂处理后,废水中Pb2+、Cu2+和Ni2+含量显著低于国家排放标准.     

Surface charge and adsorption from water onto quartz sand of humic acid

The surface charge of humic acid under different conditions of ionic strength, pH, and the presence of various cationic ions (Cu(2+), Zn(2+), Ba(2+), and Ca(2+)) was determined by a titration method using a cationic polyelectrolyte as titrant. Adsorption isotherms in batch experiments of the polymer from water onto quartz sand were determined at 20 degrees C, 40 degrees C, and 60 degrees C and under different conditions of ionic strength, pH, and the presence of various cationic ions (Cu(2+), Zn(2+), Ba(2+), and Ca(2+)). The data indicate significant decrease of humic acid surface charge by decreasing the pH value from 10.0 to 4.1. Similar decrease of humic acid surface charge was observed by increasing either the ionic strength or the affinity of the divalent cation toward the humic acid. At ambient temperature the adsorption of humic acid on the quartz sand seems to be controlled mainly by electrical interaction between the organic particle and the solid substrate. A correlation is found between the surface charge and the adsorbed amount of the polymer, the adsorbed amount increases when the surface charge of humic acid decreases. The increase of the adsorbed amount with the temperature suggests that adsorption process is endothermic.     

Sorption studies of heavy metal ions on a novel chelating resin and its application in the stripping of mercury (II)

A chelating resin containing a stable thiol group was synthesised, using polystyrene as the starting material. The resin is stable towards conc. HCl, 0.1M HNO(3) and 0.1M NaOH. The resin shows affinity towards Ag(+), Hg(2+), Bi(3+), Pb(2+), Cu(2+), Zn(2+) and Cd(2+). Extraction of these metal ions as a function of pH, kinetics of exchange and breakthrough capacities is evaluated. The selectivity of the resin for the metal ions is in the order Ag(+) > Hg2+ > Cu2+ > Pb2+ > Cd2+ > Zn2+. The equilibrium constants for exchange and kinetics of exchange are favourable for the recovery of mercury from lean sources. Application of the resin in the stripping of mercury from chlor-alkali plant affluent, and in the enrichment of mercury from seawater, have been investigated. Mercury sorbed resin can be regenerated using 5% thiourea in 0.1M HCl.     

Metal homeostasis in Hypogymnia physodes is controlled by lichen substances

The hypothesis was tested that the lichen substances produced by the epiphytic lichen Hypogymnia physodes control the intracellular uptake of divalent transition metals. Incubating lichen thalli with and without their natural content of lichen substances with metal solutions showed that the lichen substances of H. physodes selectively inhibit the uptake of Cu(2+) and Mn(2+), but not of Fe(2+) and Zn(2+). Such behavior is ecologically beneficial, as ambient concentrations of Cu(2+) and Mn(2+) in precipitation and bark are known to limit the abundance of H. physodes, whereas limiting effects of Fe(2+) or Zn(2+) have never been found. This suggests that increasing the Cu(2+) and Mn(2+) tolerance stimulated the evolution of lichen substances in H. physodes. The depsidone physodalic acid is apparently most effective at reducing Cu(2+) and Mn(2+) uptake among the seven lichen substances produced by H. physodes. Probably lichen substances play a general role in the metal homeostasis of lichens.     

In Vitro effects of various xenobiotics on Azotobacter chroococcum strains isolated from soils of southern Poland

Fourteen Azotobacter chroococcum strains isolated from soils of Southern Poland were studied concerning resistance to various xenobiotics: heavy metal ions: Cd(2+,) Cu(2+), Fe(3+), Mn(2+), Pb(2+), Zn(2+), pesticides: herbicides linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and combination of mecoprop ((RS)-2-(4-chloro-2-methylphenoxy)propanoic acid), dicamba (3,6-dichloro-2-methoxybenzoic acid) and MCPA (2-methyl-4-chlorophenoxyacetic acid), fungicide copper oxychloride, insecticide fenitrothion (O,O-Dimethyl O-(3-methyl-4-nitrophenyl) phosphorothioate) and eight antibiotics commonly used against Gram-negative bacteria. The tested soils were divided into seven groups of land use: forest, field crop, park, urban lawn, industrial area, garden and fallow land, and were analyzed for the following heavy metal ion concentrations using the atomic absorption spectrometry (AAS) technique: Cd(2+,) Cu(2+), Fe(3+), Mn(2+), Pb(2+), Zn(2+). All strains were resistant to Pb(2+), whereas other metals caused the growth inhibition of the analyzed strains. There was no significant relationship between metal concentrations in the analyzed soils and metal resistance of the isolates. Herbicide linuron did not inhibit the growth of A. chroococcum in any of the concentrations. All other pesticides caused the growth inhibition only in the concentrate forms. All isolates were sensitive to β-lactam antibiotic Meropenem, however high intraspecies differentiation was observed concerning resistance to other antibiotics. The obtained results require further study regarding resistance mechanisms and possible use of the xenobiotic-resistant strains in land rehabilitation.     

Potentially toxic metals in ombrotrophic peat along a 400 km English-Scottish transect

Four samples of ombrotrophic peat were collected from each of 10 upland locations in a transect from the southern Pennines to the Highland Boundary Fault, a total distance of ca. 400 km. Bulk compositions and other properties were determined. Total contents of Al and heavy metals (Ni, Cu, Zn, Cd, Pb) were determined following digestion with hydrofluoric acid, and concentrations of metals extractable with dilute nitric acid were also measured. Supernatants obtained from aqueous extractions of the peat samples were analysed for pH, major cations and anions, dissolved organic carbon and dissolved metals, and concentrations of free metal ions (Al(3+), Ni(2+), etc.) were estimated by applying a chemical speciation model. Both total and HNO(3)-extractable metal concentrations varied along the transect, the highest values being found at locations close to industrial and former mining areas. The HNO(3)-extractable soil metal contents of Ni, Cu and Cd were appreciably lower than lowest-observed-effect-concentrations (LOEC) for toxicity towards microorganisms in acid, organic rich soils. However, the contents of Zn at two locations, and of Pb at five locations exceeded LOECs, suggesting that they may be exerting toxic effects in the peats. Soil solution concentrations of free heavy metal ions (Cu(2+), Zn(2+), Cd(2+), Pb(2+)) were substantially lower than LOECs for toxicity towards vascular plants, whereas concentrations of Al(3+) were near to toxic levels at two locations.     

Throughfall chemistry in a spruce chronosequence in southern Poland

The chemical composition of throughfall and canopy leaching, as well as the acid neutralizing capacity and alkalinity depended on the age of Norway spruce (Picea abies Karst) stands and season of the year. A higher amount of sulphur and strong acids was deposited to the soil in the older age classes. Concentrations of SO(4)(2)(-), K(+), H(+), Mn(2+), Fe(2+) and Zn(2+) in throughfall were higher than in bulk precipitation in any season. This suggests that these ions were washed out or washed from the surface of needles and/or barks. The other ions NO(3)(-), NH(4)(+), Ca(2+) and Mg(2+) were retained by the canopy, in particular Ca(2+) and Mg(2+) during the growing season in young stands. Principal component analysis identified five factors responsible for the data structure and suggested the major anthropogenic emission sources were acidic emission (SO(4)(2)(-)+NO(3)(-)), heavy metals-dust particles (Fe(2+)+Mn(2+)+Zn(2+)), ammonium (NH(4)(+)) and H(+), while the natural-origin emission was mineral dust (Na(+)+K(+)+Ca(2+)+Mg(2+)).     

Electrochemical and FTIR studies of the mutual influence of lead(II) or iron(III) and phenol on their adsorption from aqueous acid solution by modified activated carbons

Cyclic voltammetry and spectral FTIR studies of the influence of activated carbon surface modification on the co-adsorption of metal cation (lead or iron) and phenol from aqueous acidic solution were carried out. The diversity in surface chemical structure was achieved by applying different procedures of inorganic matter removal and by modifying the carbon samples in various ways: heating under vacuum, aminoxidation in an ammonia-oxygen atmosphere, oxidation with concentrated nitric acid. The quantities of adsorbed metal ions (Pb(2+) or Fe(3+)) and phenol from solutions containing cation or phenol separately or in a mixture were determined. The adsorption capacity from acidic aqueous acidic solution depends on the chemical properties of the activated carbon surface (e.g., decrease in phenol adsorption with relative lower basicity of the adsorbent). The electrochemical parameters of electrodes made from the carbon samples were estimated, and some possible electrochemical reactions were determined from voltammograms recorded in acid electrolyte solution containing adsorbed species (separately or as a mixture). Relationships were found between metal ion adsorption and electrochemical behavior of Pb(2+)/Pb(4+) and Fe(3+)/Fe(2+) couples on the one hand, and the presence of phenol in the solutions tested and the influence of surface chemistry of the carbon electrodes on electrochemical processes on the other. The changes in adsorption capacity with respect to the adsorbates used and the changes in FTIR spectra of the carbons as a result of adsorption and/or coupling phenol molecules are discussed.     

Influence of metal ion on sorption of p-nitrophenol onto sediment in the presence of cetylpyridinium chloride

Heavy metals and surfactants have a significant effect on the sorption of organic contaminants. In this study, batch equilibrium experiments were carried out to investigate the influence of Pb(NO(3))(2) on the sorption of p-nitrophenol (PNP) onto sediments in the presence of cationic surfactant cetylpyridinium chloride (CPC). Results indicated that in the complex system containing PNP, Pb(NO(3))(2) and CPC, the sorption of PNP decreased with increasing concentration of Pb(NO(3))(2) due primarily to competing for adsorption sites. Likewise, partitioning of PNP in adsorbed surfactant layers and micelles decreased with increasing level of Pb(NO(3))(2). Moreover, the influence of different metal ions (Pb(2+), Cd(2+), Zn(2+)) was examined and results indicated that the presence of heavy metals inhibited the sorption of PNP in the order: Pb(2+)>Cd(2+)>Zn(2+). The competitive effect of the heavy metals was in agreement with the hydration energy and hydrated radius. The results are believed to provide a useful insight into describing the transport and fate of PNP in natural environments.     

Effect of complexation with humic substances on diffusion of metal ions in water

Most studies on diffusion of metal ions in various water-rock systems have dealt with free ions (hydrated ions). However, it is often the case that metal ions are dissolved as complexed species such as with humic substances (HS) in natural waters. Hence, we need to study the diffusion behavior of these complexes in order to understand fully the diffusion phenomenon in natural. In this study, the diffusion coefficients of free metal ions (M(z+)) and their complexes with HS (M-HS) were compared to understand the effect of complexation with HS on the diffusion of metal ions such as Co(2+), Cd(2+), and rare earth elements (REE(3+)). Although the diffusion coefficients of free metal ions depend on ionic potential, such dependence was not observed in the presence of HS. Comparing the diffusion coefficients of metal complexes with ethylenediaminetetraacetate (EDTA), fulvic acid, and humic acid showed that the molecular weight (MW), or the size of the ligand, is of primary importance for the diffusion of M-HS. As a consequence, the diffusion coefficients of all REE(3+) were similar in the presence of HS, while they were different in the absence of HS due to the different size of each REE(3+). The similarity among the diffusion coefficients of REE-HS was caused by the much larger size of HS compared with each ion. However, the distribution coefficients of M-HS were not similar among REE(3+), Cd(2+), and Co(2+). REE(3+) and Cd(2+) which have higher affinities for larger MW fraction in HS diffused slower than Co(2+) which favors smaller MW fraction. The results show that the affinity for different MW fractions among HS controls the diffusion of M-HS, which must be important to predict precisely the diffusion behavior of metal ions bound to HS in natural systems.     

Accumulation of Al, Mn, Fe, Cu, Zn, Cd and Pb by the bryophyte Scapania undulata in three upland waters of different pH.

Measurements were made of the contents of Al, Mn, Fe, Cu, Zn, Cd and Pb in Scapania undulata in three streams (D2, D5, D11) in the English Lake District. The stream waters had average pH values of 5.35 (D2), 5.81 (D5) and 7.26 (D11), the main differences in other major chemical components being in Mg, Al, Ca and alkalinity. There was generally more metal accumulation in the older parts of the plants, but this was not significant in all cases. Extents of accumulation varied with stream pH and dissolved metal concentration. For Al, accumulation was greatest in streams D2 and D5. Mn accumulated most in D5 and Fe was without preference. Cu, Zn and Cd accumulated mostly in the plants in stream D11 and Pb accumulated more in D5 and D11. In terms of enrichment factors (amount of metal in the plants divided by stream water concentration) the sequence was Zn < Cd < Cu < Mn < Pb < Al < Fe. Laboratory experiments supported the findings of the field data, providing evidence that uptake increases with pH at constant total metal concentration. The results are interpreted qualitatively in terms of the chemical speciation of the metals in the stream water and competition between metal ions and protons at the plant-water interface. It is suggested that Al, Cu, Zn, Cd and Pb behave according to chemical complexation, whereas redox processes and/or colloidal interactions may be significant for Mn and Fe.     

Hydrochemical characteristics of mine waters from abandoned mining sites in Serbia and their impact on surface water quality

Upon completion of exploration and extraction of mineral resources, many mining sites have been abandoned without previously putting environmental protection measures in place. As a consequence, mine waters originating from such sites are discharged freely into surface water. Regional scale analyses were conducted to determine the hydrochemical characteristics of mine waters from abandoned sites featuring metal (Cu, Pb–Zn, Au, Fe, Sb, Mo, Bi, Hg) deposits, non-metallic minerals (coal, Mg, F, B) and uranium. The study included 80 mine water samples from 59 abandoned mining sites. Their cation composition was dominated by Ca²⁺, while the most common anions were found to be SO₄ ^2? and HCO₃ ^?. Strong correlations were established between the pH level and metal (Fe, Mn, Zn, Cu) concentrations in the mine waters. Hierarchical cluster analysis was applied to parameters generally indicative of pollution, such as pH, TDS, SO₄ ^2?, Fe total, and As total. Following this approach, mine water samples were grouped into three main clusters and six subclusters, depending on their potential environmental impact. Principal component analysis was used to group together variables that share the same variance. The extracted principal components indicated that sulfide oxidation and weathering of silicate and carbonate rocks were the primary processes, while pH buffering, adsorption and ion exchange were secondary drivers of the chemical composition of the analyzed mine waters. Surface waters, which received the mine waters, were examined. Analysis showed increases of sulfate and metal concentrations and general degradation of surface water quality.     

Removal of Cu and Pb by tartaric acid modified rice husk from aqueous solutions

A study on the modification of rice husk by various carboxylic acids showed that tartaric acid modified rice husk (TARH) had the highest binding capacities for Cu and Pb. The carboxyl groups on the surface of the modified rice husk were primarily responsible for the sorption of metal ions. A series of batch experiments using TARH as the sorbent for the removal of Cu and Pb showed that the sorption process was pH dependent, rapid and exothermic. The sorption process conformed to the Langmuir isotherm with maximum sorption capacities of 29 and 108 mg/g at 27 +/- 2 degrees C for Cu and Pb, respectively. The uptake increased with agitation rate. Decrease in sorbent particle size led to an increase in the sorption of metal ions and this could be explained by an increase in surface area and hence binding sites. Metal uptake was reduced in the presence of competitive cations and chelators. The affinity of TARH for Pb is greater than Cu.     

Correlating metal ionic characteristics with biosorption capacity using QSAR model

The relationship between metal ionic characteristics and the maximum biosorption capacity (q(max)) was established using QSAR model based on the classification of metal ions (soft, hard and borderline ions). Ten kinds of metal ions (Ag(+), Cs(+), Zn(2+), Pb(2+), N(i2+), Cu(2+), Co(2+), Sr(2+), Cd(2+), Cr(3+)) were selected and the waste biomass of Saccharomyces cerevisiae obtained from a local brewery was used as biosorbent. Eighteen parameters of physiochemical characteristics of metal ions were selected and correlated with q(max). Classification of metal ions could improve the QSAR models and different characteristics were significant in correlating with q(max), such as polarizing power Z(2)/r or the first hydrolysis constant |logK(OH)| or ionization potential IP. X(m)(2)r seemed to be suitable for metal ions including soft ions, and Z(2)/r, |logK(OH)| and IP suitable for only soft ions or metal ions excluding soft ions. It provided a new way to predict the biosorptive capacity of metal ions.     

Involvement of siderophores in the reduction of metal-induced inhibition of auxin synthesis in Streptomyces spp

Unlike synthetic metal chelators, microbe-assisted phytoremediation provides plants with natural metal-solubilizing chelators which do not constitute a potential source of environmental pollution. Concurrently with microbial chelators, plant growth promotion can be enhanced through bacterially-produced phytohormones. In this work, the simultaneous production of siderophores and auxins by Streptomyces was studied to gain insight for future application in plant growth and phytoremediation in a metal-contaminated soil. Standard auxin and siderophore detection assays indicated that all of the investigated Streptomyces strains can produce these metabolites simultaneously. However, Al(3+), Cd(2+), Cu(2+), Fe(3+) and Ni(2+), or a combination of Fe(3+) and Cd(2+), and Fe(3+) and Ni(2+) affected auxin production negatively, as revealed by spectrophotometry and gas chromatography-mass spectrometry. This effect was more dramatic in a siderophore-deficient mutant. In contrast, except for Fe, all the metals stimulated siderophore production. Mass spectrometry showed that siderophore and auxin-containing supernatants from a representative Streptomyces species contain three different hydroxamate siderophores, revealing the individual binding responses of these siderophores to Cd(2+) and Ni(2+), and thus, showing their auxin-stimulating effects. We conclude that siderophores promote auxin synthesis in the presence of Al(3+), Cd(2+), Cu(2+) and Ni(2+) by chelating these metals. Chelation makes the metals less able to inhibit the synthesis of auxins, and potentially increases the plant growth-promoting effects of auxins, which in turn enhances the phytoremediation potential of plants.     

Heavy metals effects on proteolytic system in sunflower leaves

Plant proteolytic system includes proteases, mainly localized inside the organelles, and the ubiquitin-proteasome pathway in both, the cytoplasm and the nucleus. It was recently demonstrated that under severe Cd stress sunflower (Helianthus annuus L.) proteasome activity is reduced and this results in accumulation of oxidized proteins. In order to test if under other heavy metal stresses sunflower proteolytic system undergoes similar changes, an hydroponic experiment was carried out. Ten days old sunflower plants were transferred to hydroponic culture solutions devoid (control) or containing 100 microM of AlCl(3), CoCl(2), CuCl(2), CrCl(3), HgCl(2), NiCl(2), PbCl(2) or ZnCl(2) and analyzed for protein oxidative damage and proteolytic activities. After 4 days of metal treatment, only Co(2+), Cu(2+), Hg(2+), and Ni(2+) were found to increase carbonyl groups content. Except for Al(3+) and Zn(2+), all metals tested significantly reduced all proteasome activities (chymotrypsin-like, trypsin-like and PGPH) and acid and neutral proteases activities. The effect on basic proteases was more variable. Abundance of 20S protein after metal treatments was similar to that obtained for control samples. Co(2+), Cu(2+), Hg(2+), Ni(2+), Cr(3+), and Pb(2+) induced accumulation of ubiquitin conjugated proteins. It is concluded that heavy metal effects on proteolytic system cannot be generalized; however, impairment of proteasome functionality and decreased proteases activities seem to be a common feature involved in metal toxicity to plants.     

Heavy metals incidence in the application of inorganic fertilizers and pesticides to rice farming soils

The concentrations of Cd, Co, Cu, Ni, Pb, Zn, Fe and Mn in different inorganic fertilizers (urea, calcium superphosphate, iron sulphate and copper sulphate) and in pesticides (two herbicides and one fungicide) are evaluated together with the contribution of these metals in soils from their use. The study was made in rice farming areas to the north of Albufera Natural Park (Valencia, Spain). The results obtained show that superphosphate is the fertilizer that contains the highest concentrations of Cd, Co, Cu and Zn as impurities. Copper sulphate and iron sulphate have the most significant concentrations of Pb, and are the only fertilizers in which Ni was detected. The three pesticides analysed show similar Cd contents and the highest levels of Fe, Mn, Zn, Pb and Ni are found in the herbicides. The most significant additions of heavy metals as impurities that soil receives from agricultural practices, are Mn, Zn, Co and Pb. Three contamination indexes have been applied to provide a basis for comparison of potential heavy metal toxicity. These results denote the potential toxicity of heavy metals in the studied soils.     

叉鞭金藻对微量锌、镉的吸附效应研究

研究了叉鞭金藻对微量Zn^2 ,Cd^2 的生物吸附及其机理。结果表明,叉鞭金藻对Zn^2 ,Cd^2 的生物吸附主要经历了快速的吸附和缓慢的吸附两个步骤。pH为6～7时,叉鞭金藻对Zn^2 ,Cd^2 有较好的吸附作用,且死体藻细胞比活体藻细胞能富集更多的Zn^2 ,Cd^2 。吸附符合Freundlich等温吸附模型。     

电镀污泥回收重金属的新工艺

合理、经济地处理混合电镀污泥,回收其中有价值的金属具有重要意义。以不同的酸作为浸出剂对电镀污泥中的金属进行了浸出效果实验。结果表明,在相同条件下,各酸的浸出效果顺序为:硫酸>盐酸>王水>硝酸;液体水与固体电镀污泥比为3,干污泥为5 g,硫酸加入量为15 mL,时间1 h条件下,混合电镀污泥中金属铜锌的浸出率最大,达到97.38%。分别采用铁和铁锰合金还原剂常温还原低熔点重金属离子铜、锌,浸出液中99%以上含量的铜、锌沉淀,使低熔点重金属与黑色金属铁、锰、铬有效分离。低熔点混合重金属可以用来做铜合金添加剂使用,最后沉淀的混合黑色金属氢氧化物处理后可以用来做炼钢合金添加剂使用。     

Heavy metals removal from wastewaters using organic solid waste—rice husk

In this study, the removal of Cr(III) and Cu(II) from contaminated wastewaters by rice husk, as an organic solid waste, was investigated. Experiments were performed to investigate the influence of wastewater initial concentration, pH of solution, and contact time on the efficiency of Cr(III) and Cu(II) removal. The results indicated that the maximum removal of Cr(III) and Cu(II) occurred at pH 5–6 by rice husk and removal rate increased by increased pH from 1 to 6. It could be concluded that the removal efficiency was enhanced by increasing wastewater initial concentration in the first percentage of adsorption and then decreased due to saturation of rice husk particles. Also according to achieved results, calculated saturation capacity in per gram rice husk for Cr(III) and Cu(II) were 30 and 22.5 mg?g^?1, respectively. The amounts of Cr(III) and Cu(II) adsorbed increased with increase in their contact time. The rate of reaction was fast. So that 15–20 min after the start of the reaction, between 50 and 60 % of metal ions were removed. Finally, contact time of 60 min as the optimum contact time was proposed.