Laccase-catalyzed removal of 2,4-dimethylphenol from synthetic wastewater: effect of polyethylene glycol and dissolved oxygen

The potential use of laccase (SP-504) in an advanced oxidation-based treatment technology to remove 2,4-dimethylphenol (DMP) from water was investigated with and without the additive, polyethylene glycol (PEG). The DMP concentration was varied between 1.0 and 5.0 mM. The optimization of pH and enzyme concentration in the presence and absence of PEG was carried out. All experiments were carried out in continuously stirred reactors for 3h at room temperature. The reaction was initiated by adding enzyme to the reaction mixture. For more than 95% removal of DMP, the presence of PEG reduced the inactivation of enzyme so that the required enzyme concentrations were reduced by about 2-fold compared to the same reactions in the absence of PEG. Finally, the PEG concentrations were optimized to obtain the minimum dose required. For higher substrate concentrations, the availability of oxygen was insufficient in achieving 95% or more removal. Therefore, the effect of increasing dissolved oxygen at higher substrate concentration was investigated. The laccase studied was capable of efficiently removing DMP at very low enzyme concentrations and hence shows great potential for cost-effective industrial applications.     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

O3/H2O2法去除浮选药剂丁基黄药

采用O3/H2O2法去除水中丁基黄药,考察了H2O2/O3摩尔比、pH值、丁基黄药初始浓度、温度和自由基抑制剂对丁基黄药的去除效果的影响。结果表明,在相同O3投加量下,H2O2量越大,丁基黄药去除率越高。pH值为7～9,温度在293～303 K的范围内,O3/H2O2对丁基黄药都有很高的去除率。碳酸氢根和叔丁醇能在一定程度上降低丁基黄药的降解效率。研究还发现,在O3和H2O2投加量相同的条件下,H2O2多次投加对水中丁基黄药的处理效果明显优于一次性投加。GC/MS分析表明,O3/H2O2氧化丁基黄药氧化产物为羧酸类物质。     

Phenol photonitration upon UV irradiation of nitrite in aqueous solution I: effects of oxygen and 2-propanol.

Nitrophenols are formed in aqueous solution upon UV irradiation of phenol and nitrite. The formation of nitrophenols is enhanced by dissolved oxygen and inhibited by the addition of 2-propanol. The mechanism of phenol photonitration involves both .NO2 (or N2O4, reacting with phenol, and 4-nitrosophenol, which is oxidised to 4-nitrophenol. A reaction scheme is proposed based on experimental results.     

Hydrogen peroxide mediated photodegradation of phenol as studied by a flash photolysis/HPLC technique

The technique of flash photolysis followed by high-performance liquid chromatography has been applied to the study of the photodegradation of phenol (I) in the presence of hydrogen peroxide. Progress of the reaction of I (0.1 mM) in undegassed aqueous solution ([H2O2]/[I] = 200/l) was observed by using multiple flashes (16 J). Analysis after a single flash indicated that catechol and hydroquinone were the primary products of the reaction. The reaction was found to be independent of pH in the range 7.0-9.0, but the yield of degradation decreased at pH > 9.0 and at pH < 7.0. The effects of the hydrogen peroxide concentration and flash energy on the chemical yield of the pollutant degradation, and product formation, were investigated as well. The mechanism of the reaction is discussed. A possibility of the application of flashlamps as powerful sources of the UV irradiation in industrial reactors for wastewater treatment is suggested.     

Chemical oxidation of sulfadiazine by the Fenton process: Kinetics,pathways, toxicity evaluation

This paper investigated sulfadiazine oxidation by the Fenton process under various reaction conditions. The reaction conditions tested in the experiments included the initial pH value of reaction solutions, and the dosages of ferrous ions and hydrogen peroxide. Under the reaction conditions with pH 3, 0.25 mM of ferrous ion and 2 mM of hydrogen peroxide, a removal efficiency of nearly 100% was achieved for sulfadiazine. A series of intermediate products including 4-OH-sulfadiazine/or 5-OH-sulfadiazine, 2-aminopyrimidine, sulfanilamide, formic acid, and oxalic acid were identified. Based on these products, the possible oxidation pathway of sulfadiazine by Fenton's reagent was proposed. The toxicity evaluation of reaction solutions showed increased antimicrobial effects following the Fenton oxidation process. The results from this study suggest that the Fenton oxidation process could remove sulfadiazine, but also increase solution toxicity due to the presence of more toxic products.     

Citric acid-modified Fenton's reaction for the oxidation of chlorinated ethylenes in soil solution systems

Fenton's reagent, a solution of hydrogen peroxide and ferrous iron catalyst, is used for an in situ chemical oxidation of organic contaminants. Sulfuric acid is commonly used to create an acidic condition needed for catalytic oxidation. Fenton's reaction often involves pressure buildup and precipitation of reaction products, which can cause safety hazards and diminish efficiency. We selected citric acid, a food-grade substance, as an acidifying agent to evaluate its efficiencies for organic contaminant removal in Fenton's reaction, and examined the impacts of using citric acid on the unwanted reaction products. A series of batch and column experiments were performed with varying H2O2 concentrations to decompose selected chlorinated ethylenes. Either dissolved iron from soil or iron sulfate salt was added to provide the iron catalyst in the batch tests. Batch experiments revealed that both citric and sulfuric acid systems achieved over 90% contaminant removal rates, and the presence of iron catalyst was essential for effective decontamination. Batch tests with citric acid showed no signs of pressure accumulation and solid precipitations, however the results suggested that an excessive usage of H2O2 relative to iron catalysts (Fe2+/H2O2<1/330) would result in lowering the efficiency of contaminant removal by iron chelation in the citric acid system. Column tests confirmed that citric acid could provide suitable acidic conditions to achieve higher than 55% contaminant removal rates.     

Oxidation of diethylene glycol with ozone and modified Fenton processes

This paper describes a study of oxidation of diethylene glycol (DEG) by ozone and modified Fenton process (hydrogen peroxide and ferric salt mixture) in aqueous solution. Both oxidation processes were able to oxidize relatively high concentrations of DEG effectively. DEG reacted primarily through hydroxyl radical produced by decomposition of ozone, and about 3 mol of ozone were consumed per mole of DEG removed during the process. For modified Fenton oxidation, stepwise addition of hydrogen peroxide (H2O2) and ferric salt (Fe(III)) resulted in much higher removal of DEG than one-time pulse addition of the chemicals. The extent of DEG removal increased with increasing concentrations of both H2O2 and Fe(III). Oxidant consumption per mole of DEG oxidized was one order of magnitude higher for hydrogen peroxide than those observed for ozone. Overall, ozonation produced higher concentrations of aldehydes, and modified Fenton treatment produced higher concentrations of carboxylic acids for the same levels of DEG oxidation. The major products of ozonation were glycolaldehyde, glyoxal, formaldehyde, acetaldehyde, and acetic, formic, pyruvic, oxalic and glyoxalic acids. The major products of modified Fenton oxidation were formaldehyde, and formic and acetic acids.     

Degradation of 2,4-dichlorophenol by combining photo-assisted Fenton reaction and biological treatment.

The photo-Fenton reaction effect on the biodegradability improvement of 100 mg/L solution of 2,4-dichlorophenol (DCP) has been investigated. Biochemical oxygen demand (BOD) at 5 and 21 days, BODn/ chemical oxygen demand (COD) and BODn/total organic carbon (TOC) ratios, average oxidation state, and inhibition on activated sludge were monitored. For 50 mg/L hydrogen peroxide and 10 mg/L iron(II) initial concentrations and 40 minutes of reaction time in the photo-Fenton process, the biodegradability of the pretreated solution, measured as BOD5/COD ratio, was improved from 0 for the original DCP solution up to 0.18 (BOD21/COD = 0.24). At that point, all DCP was eliminated from the solution. To study the effect of the pretreatment step, the biological oxidation of pretreated solutions was tested in two semicontinuous stirred tank reactors, one operated with activated sludge and one with biomass acclimated to phenol. Results showed that more than 80% TOC removal could be obtained by codigestion of the pretreated solution with municipal wastewater. Total organic carbon removals of approximately 60% were also obtained when the sole carbon source for the aerobic reactors was the pretreated solution. The hydraulic retention times used in the bioreactors were of the same order of magnitude as those used at domestic wastewater treatment plants (i.e., between 12 and 24 hours). Kinetic studies based on pseudo-first-order kinetics have also been carried out. Constants were found to be in range 0.67 to 1.7 L x g total volatiles suspended solids(-1) x h(-1).     

Oxidation of industrial dyeing wastewater by supercritical water oxidation in transpiring-wall reactor.

Industrial dyeing wastewater was oxidized in supercritical water in a transpiring-wall reactor, using hydrogen peroxide as an oxidant. Experiments were performed at 595 to 704 K and 18 to 30 MPa, with an oxidant dosage ratio ranging from 0.6 to 2.0. A chemical oxygen demand (COD) removal of more than 98.4% was achieved at 704 K and 28 MPa, with a retention time less than 35 seconds, which increased with the temperature, pressure, and oxidant. A modified first-order rate expression was regressed from experimental data, taking into account the influence of induction time. The resulting pre-exponential factor, A, and activation energy, Ea, were 1.07 seconds(-1) and 12.12 kJ x mol(-1), respectively, while the reaction order for feed wastewater (based on COD) and oxidant were assumed to be 1 and 0, respectively. Gas chromatography/mass spectrometry analysis for effluents indicated that carbon dioxide, carbon monoxide, and nitrogen were the main reaction products, and phenol; benzenecarboxylic acid; 1, 2-benzenedicarboxylic acid; and isoquinoline were detected as intermediates.     

Advanced oxidation of natural organic matter using hydrogen peroxide and iron-coated pumice particles

The oxidative removal of natural organic matter (NOM) from waters using hydrogen peroxide and iron-coated pumice particles as heterogeneous catalysts was investigated. Two NOM sources were tested: humic acid solution and a natural source water. Iron coated pumice removed about half of the dissolved organic carbon (DOC) concentration at a dose of 3000 mg l(-1) in 24 h by adsorption only. Original pumice and peroxide dosed together provided UV absorbance reductions as high as 49%, mainly due to the presence of metal oxides including Al(2)O(3), Fe(2)O(3) and TiO(2) in the natural pumice, which are known to catalyze the decomposition of peroxide forming strong oxidants. Coating the original pumice particles with iron oxides significantly enhanced the removal of NOM with peroxide. A strong linear correlation was found between iron contents of coated pumices and UV absorbance reductions. Peroxide consumption also correlated with UV absorbance reduction. Control experiments proved the effective coating and the stability of iron oxide species bound on pumice surfaces. Results overall indicated that in addition to adsorptive removal of NOM by metal oxides on pumice surfaces, surface reactions between iron oxides and peroxide result in the formation of strong oxidants, probably like hydroxyl radicals, which further oxidize both adsorbed NOM and remaining NOM in solution, similar to those in Fenton-like reactions.     

Treatment of coking wastewater by an advanced Fenton oxidation process using iron powder and hydrogen peroxide

In this study the treatment of coking wastewater was investigated by an advanced Fenton oxidation process using iron powder and hydrogen peroxide. Particular attention was paid to the effect of initial pH, dosage of H₂O₂ and to improvement in biodegradation. The results showed that higher COD and total phenol removal rates were achieved with a decrease in initial pH and an increase in H₂O₂ dosage. At an initial pH of less than 6.5 and H₂O₂ concentration of 0.3 M, COD removal reached 44-50% and approximately 95% of total phenol removal was achieved at a reaction time of 1 h. The oxygen uptake rate of the effluent measured at a reaction time of 1 h increased by approximately 65% compared to that of the raw coking wastewater. This indicated that biodegradation of the coking wastewater was significantly improved. Several organic compounds, including bifuran, quinoline, resorcinol and benzofuranol were removed completely as determined by GC-MS analysis. The advanced Fenton oxidation process is an effective pretreatment method for the removal of organic pollutants from coking wastewater. This process increases biodegradation, and may be combined with a classical biological process to achieve effluent of high quality.     

Photoelectro-Fenton mineralization of phenol through optimization of ferrous regeneration

The degradation of phenol in acidic solution at pH 3 has been investigated under various photo- and electrochemical conditions. A laboratory-scale reactor on which were mounted net electrodes (RuO₂/IrO₂-coated Ti anodes (DSA) and stainless steel cathodes) and 254 nm UV lamps was established to effectively reduce ferric reagents. The experimental results of the photoelectron-chemical reaction suggested that the current efficiency of reducing ferric ion was improved by increasing the number of electrodes used, and the UV lamps were important to inducing the reduction of ferric carboxylates, which were the major intermediates that were formed upon a particular degree of phenol oxidation. Accordingly, the addition of an initial concentration of 400 ppm ferrous salt and 10,200 ppm hydrogen peroxide (in a continuous mode) resulted in the removal of over 92 % of TOC (initial phenol?=?2,000 ppm, TOC?=?1,532 ppm) by 4 h of the photoelectro-Fenton and the sequential 2 h of the photo-Fenton processes. HPLC was utilized to monitor the formation of aromatic and carboxylate byproducts, and revealed that the aid of photo irradiation eliminated most of the oxalate residue from the final solution, which would have contributed to the 25 % of the TOC that was inactive in the electrolytic system.     

The role of ferrous ion in Fenton and photo-Fenton processes for the degradation of phenol

The efficiency of different Fenton-related oxidative processes such as Fenton, solar-Fenton and UV-Fenton were examined using phenol as a model compound in simulated and industrial wastewater. A batch study was conducted to optimize parameters like pH, hydrogen peroxide concentration and ferrous ion concentration governing the Fenton process. At optimum conditions, different Fenton-related processes were compared for the degradation of phenol. Increased degradation and mineralisation efficiency were observed in photo-Fenton processes as compared to conventional Fenton process. The maximum mineralising efficiency for phenol with Fenton, solar and UV-Fenton processes were 41%, 96% and 97% respectively. In Fenton process, carboxylic acids like acetic acid and oxalic acid were formed as end products during the degradation of phenol while in photo-Fenton processes, both these ions were identified during the early stages of phenol degradation and were oxidized almost completely at 120 min of the reaction time. In photo-Fenton processes (solar and UV light) complete degradation were observed with 0.4 mM of Fe2+ catalyst as compared to 0.8 mM of Fe2+ in conventional Fenton process. In Fenton and solar-Fenton processes, an iron reusability study was performed to minimize the amount of iron used in treatment process. The efficacy of Fenton and solar-Fenton processes was applied to effluent from phenol resin-manufacturing unit for the removal and mineralisation of phenol.     

复合酸化剂对电镀污泥中铬、铜的去除效果

以电镀加工厂产生的污水污泥作为主要研究对象,研究了柠檬酸、硝酸、过氧化氢为复合酸化剂,Fe3+为增效剂对电镀污泥中铬和铜的去除效果,考察了酸化剂的浓度、反应时间、摇床转速、污泥pH、Fe3+浓度等因素对污泥中重金属去除效率的影响。结果表明:在室温下,含0.15 mol/L柠檬酸、1.5%过氧化氢、0.25 mol/L硝酸的复合酸化剂与增效剂2.0g/L Fe3+溶液共同处理污泥,固液比为1∶10,以150 r/min的转速振荡4 h,对污泥中Cr的去除效率达到80.02%,Cu的去除效率可达到92.89%,使污泥中残留Cr、Cu含量均符合国家污泥农用标准。     

Wet peroxide degradation of atrazine

The high temperature (150-200 degrees C), high pressure (3.0-6.0 MPa) degradation of atrazine in aqueous solution has been studied. Under these extreme conditions atrazine steadily hydrolyses in the absence of oxidising agents. Additionally, oxygen partial pressure has been shown not to affect atrazine degradation rates. In no case mineralisation of the parent compound was observed. The addition of the free radical generator hydrogen peroxide to the reaction media significantly enhanced the depletion rate of atrazine. Moreover, partial mineralisation of the organics was observed when hydrogen peroxide was used. Again, oxygen presence did not influence the efficiency of the promoted reaction. Consecutive injections of hydrogen peroxide throughout the reaction period brought the total carbon content conversion to a maximum of 65-70% after 40 min of treatment (suggesting the total conversion of atrazine to cyanuric acid). Toxicity of the effluent measured in a luminometer decreased from 93% up to 23% of inhibition percentage. The process has been simulated by means of a semi-empirical model.     

Photolysis behavior of herbicide propisochlor in water media and preliminary analysis of photoproducts under different light sources

Photolysis behavior of a new herbicide propisochlor in water media as well as the effects of light sources, initial concentration of propisochlor, pH value, dissolved oxygen (DO) level, and salinity on the photolysis process was investigated. It was found that the relationship between initial concentration of propisochlor and its photodegradation rate was negatively correlated. The changes in acidity and alkalinity of the reaction medium influenced the photoreaction rate evidently. In the alkaline solution the degradation was accelerated. In the reaction media with different pH values, the photolysis followed the first-order kinetics. The presence of dissolved oxygen may promote the photolysis and there existed an optimum of dissolved oxygen concentrations. Increasing the DO level can weaken the promotion and even have an adverse effect. It was demonstrated that with dissolved oxygen the photodegradation of propisochlor followed the first-order kinetics equation. The addition of salt ions Ca2+ and Mg2+ changed the ionic strength and solvent polarity, resulting in the effect on propisochlor photolysis. The photoproducts were detected by both HPLC and GC-MS methods. It was found that photolysis products varied under different light sources. Conclusions may be reached that in the photodegradation of propisochlor, the benzene ring remained intact under irradiation of both solar light and high-pressure mercury lamp, and the amido link was relatively stable, while dechlorination was liable to take place; moreover, alpha-hydrogen at the substituent of benzene ring was active.     

Degradation mechanisms of 4-chlorophenol in a novel gas-liquid hybrid discharge reactor by pulsed high voltage system with oxygen or nitrogen bubbling

The effect of gas bubbling on the removal efficiency of 4-chlorophenol (4-CP) in aqueous solution has been investigated using a novel pulsed high voltage gas-liquid hybrid discharge reactor, which generates gas-phase discharge above the water surface simultaneously with the spark discharge directly in the liquid. The time for 100% of 4-CP degradation in the case of oxygen bubbling (7 min) was much shorter than that in the case of nitrogen bubbling (25 min) as plenty of hydrogen peroxide and ozone formed in oxygen atmosphere enhanced the removal efficiency of 4-CP. Except for the main similar intermediates (4-chlorocatechol, hydroquinone and 1,4-benzoquinone) produced in the both cases of oxygen and nitrogen bubbling, special intermediates (5-chloro-3-nitropyrocatechol, 4-chloro-2-nitrophenol, nitrate and nitrite ions) were produced in nitrogen atmosphere. The reaction pathway of 4-CP in the case of oxygen bubbling was oxygen/ozone attack on the radical hydroxylated derivatives of 4-CP. However, in the case of nitrogen bubbling, hydroxylation was the main reaction pathway with effect of N atom on degradation of 4-CP.     

水体中酮硝基麝香的臭氧氧化降解研究

采用臭氧氧化水体中的酮硝基麝香,考察pH、H2O2等因素对降解程度的影响,结果表明提高初始pH能加快酮硝基麝香的氧化降解,当pH为12时,反应时间1 h,酮硝基麝香几乎完全去除,浓度为2 mol/L和5 mol/L的H2O2存在有利于O3分解生成·OH自由基,使得酮硝基麝香的氧化降解速率加快,当H2O2浓度超过5 mol/L,H2O2会成为·OH的清除剂,降低·OH利用率;无论O3单独作用和O3/H2O2协同作用,酮硝基麝香降解符合准一级动力学规律;酮硝基麝香氧化降解产物包括甲酸、二乙酸和硝酸根等,其中硝基从苯环上脱落降低了硝基麝香对环境的风险.