细水雾仔仰制障碍物稳定火烯的实验研究

采用模拟实验的方法,研究了细水雾对障碍物后隐藏火焰的抑制效果,实验发现,对于水平方向施加水雾,能够有效地抑制火焰,通过与哈龙灭火剂灭火有效性进行对比,发现了有障碍物时,细水雾火效率尚待提高。     

障碍物遮挡条件下细水雾与油池火相互作用的实验研究

障碍物影响下细水雾灭火有效性的研究具有重要的意义。研究了障碍物与火焰的相对位置、细水雾工作压力、喷头距离火焰垂直距离及水平距离等因素对灭火有效性的影响,以及细水雾作用下火灾烟气中一氧化碳、二氧化碳及氧气浓度的变化规律等。结果表明:高压细水雾可以有效扑救部分有障碍物遮挡的油池火,同时喷头距离火焰的水平距离和垂直距离也显著影响着细水雾的灭火速度;高压细水雾在灭火过程中火场的氧气浓度明显升高,二氧化碳和一氧化碳浓度明显降低;细水雾工作压力较低时,一氧化碳浓度反而有所增加。     

基于数值模拟的细水雾在汽车涂装车间喷漆室的应用研究

采用FDS软件对细水雾扑救汽车涂装车间喷漆室火灾的灭火效能进行数值模拟分析,着重探讨了喷漆室纵向通风、细水雾雾滴粒径、雾滴喷射速度、汽车障碍物等对扑灭油漆火的影响。模拟结果表明:在细水雾与油漆火的相互作用过程中,细水雾对火源的表面冷却和隔氧窒息作用显著;为了防止室内氧气得到补充,在开启细水雾灭火的同时应当联动控制关闭纵向通风系统;在模拟工况条件下雾滴粒径为100μm~300μm的细水雾灭火效果优于粒径为400μm、500μm的细水雾;雾滴在一定喷射速度范围内速度越大灭火效果越好,喷射速度为10m/s的雾滴灭火效果明显优于3m/s和5m/s的雾滴,但是为了防止火焰横向蔓延,喷射速度不宜过高;在汽车障碍物火灾中部分微小的细水雾雾滴受到火焰的卷吸作用,可以绕过障碍物进入火区发挥冷却作用,细水雾灭火系统能够有效控制障碍物火灾,可以应用于汽车涂装车间喷漆室。     

细水雾熄灭障碍物火的实验研究和数值模拟

为了研究细水雾灭火系统在网状和条状障碍物阻隔条件下的灭火效果,采用全尺寸试验研究和数值模拟的方法研究了障碍物的形状,位置,遮挡面积以及细水雾工作压力对灭火效果的影响.实验结果表明:提高压力有助于快速有效地熄灭障碍物火;障碍物的位置是影响灭火效果的重要因素,近距离的覆盖使细水雾难以进入火区.障碍物下出现局部高温区,余火难以扑灭,灭火时间至少需要56 s;而障碍物距离火源较远时,卷吸作用下细水雾仍能均匀的进入火区,发挥冷却作用,灭火时间在18 s以内;网状障碍物的遮挡面积,对灭火效果影响不大;相同遮挡面积条件下,条状障碍物火比较难熄灭.     

细水雾抑制熄灭木材火焰的小尺度实验研究及简化模型

细水雾灭火技术以其环保性好、灭火迅速、耗水量低、破坏性小以及适用面宽等特点 ,已成为国际火灾领域关注研究的热点。以此为工程背景 ,开展了细水雾抑制熄灭木材火焰的小尺度模拟实验研究。利用热电偶测温系统、数码摄像机等仪器测量了细水雾作用前后燃烧场的变化特征。结果表明 :预燃时间、喷雾气压、细水雾作用时间等参数对灭火过程有显著影响。细水雾抑制熄灭木材火焰的主要机理是燃料表面冷却效应。从传热的角度建立的木材表面冷却模型与实验结果吻合较好     

含添加剂细水雾抑制瓦斯爆炸有效性试验研究

为进一步提高细水雾的抑爆灭火效能,在建立细水雾抑爆系统试验平台的基础上,选用MgCl2、FeCl2和NaHCO3这3种添加剂,研究细水雾对瓦斯爆炸火焰的抑制效果.结果表明:使用含添加剂细水雾后,体积分数为9.5％的瓦斯的爆炸传播速度从13.8 m/s至少降到2.75 m/s;水雾区火焰长度最多缩短了242 mm;含0.8％FeCl2的细水雾有效性系数为6,有效性最高;从火焰图片剖面像素分布可以看出,火焰的辐射体温度均出现了不同程度的降低.不同添加剂不同程度地提高了细水雾的灭火效能,对瓦斯体积分数接近化学当量比的火焰传播有明显抑制效果.     

带电细水雾的灭火实验研究

利用静电感应原理,设计了使细水雾强制带电的感应荷电装置,进行了带电细水雾的灭火实验研究。为研究带电细水雾的灭火效率,在受限空间内,采用小尺度实验方法,通过改变电压的极性和大小、针-环状电极的半径及其距伞罩电极之间的距离,分析对灭火时间和热电偶温度变化的影响。结果表明:带电细水雾比普通细水雾能更迅速地降低火焰温度、熄灭火焰,荷负电的细水雾比荷正电的细水雾具有更好的抑制效果,随着电压的增大、针-环状电极半径及两电极间距的减小,灭火效能提高,熄灭时间减少。     

不同喷射方式细水雾灭火效果的试验

细水雾的喷射方式对其灭火效果存在一定的影响。利用时间继电器控制细水雾灭火系统的启停,开展了连续式和脉冲式两种喷射方式的细水雾对开门与关门两种通风条件下不同燃料油池火分别进行抑制的试验研究。结果表明:在试验条件下,对于开门状态下连续式细水雾难以扑灭的汽油池火,脉冲式细水雾能显著提高灭火效果;对于连续式细水雾容易扑灭的柴油池火及关门状态下的汽油池火,脉冲式细水雾不能提高灭火效果,且灭火时间和用水量均有所增加;对于细水雾难以扑灭的酒精池火,连续式细水雾和脉冲式细水雾均未有效扑灭火焰。     

细水雾对障碍物遮挡火源抑制作用的数值研究

以大涡模拟、混合物分数模拟和欧拉-拉格朗日粒子运动描述法为基础,采用火灾动力学软件FDS研究了细水雾对障碍物不同程度遮挡火的抑制作用,通过改变雾滴粒径、喷头操作压力来分析细水雾对不同遮挡情况油池火的抑制灭火作用。结果表明:当火源被障碍物完全遮挡时,操作压力低于1MPa,细水雾很难达到抑制作用,当压力达到4MPa以上时,细水雾能够将温度控制在较低范围内;细水雾粒径小于50μm时,细水雾对障碍物遮挡火有较好的抑制作用;从整体来看,随着细水雾粒径的减小、压力的升高,细水雾对障碍物遮挡火的抑制作用逐渐增强。     

双流体细水雾对木垛火的灭火特性研究

使用气泡雾化喷头和氮气、空气及二氧化碳3种雾化气体对木垛火进行双流体细水雾灭火试验,研究了双流体细水雾与木垛火的相互作用特点及细水雾和雾化气体的协同灭火机理.结果表明,水流率足够的条件下,双流体细水雾可以快速抑制木垛火,但完全扑灭木垛内部的火焰需要较长时间;喷头施加的水流率越大,灭火时间越短;雾化气体起到了辅助灭火的作用,且雾化气体本身的灭火能力越强,对应的双流体细水雾的灭火时间越短.     

Full-scale experimental and numerical analysis of water mist system for sheltered fire sources in wind generator compartment

Through a series of full-scale fire experiments and numerical simulations, the effectiveness of water mist system on wind generator could be estimated, and compared with fire parameters, such as exposed or unexposed fire sources, number of nozzles, un-sheltered or sheltered fire sources, and fire source location.The experimental study found that the position of the water mist nozzles and whether the flames inside the oil pan are covered have a significant influence on overall extinguishing efficacy. The water mist system proved to have sound effectiveness on fire suppression in wind generators with sheltered fire source.According to FDS simulations of water mist systems, the simulated temperature curve declined more significantly than that for the actual measurements, indicating that the cooling effect of the simulated water mist was better. However, simulations were used for a situation where water mist was unable to directly extinguish the fire. Analysis of the simulated airflow showed that an opening caused the water to discharge outwards and the airflow was disturbed by the outside; thus, the extinguishing effect was poorer. There was less water with a sheltering object, and thus the extinguishing effect was poorer.     

受限空间脉冲细水雾灭火数值模拟

为研究脉冲细水雾灭火效果和灭火机理,采用FDS软件对连续和脉冲细水雾熄灭受限空间油盘火进行了数值模拟。通过模拟和理论分析确定了脉冲细水雾周期为8 s开启、8 s暂停,并设置了冷却和窒息两种灭火条件,对两种细水雾熄灭不同尺寸的柴油池火进行了研究。结果表明:连续细水雾无法熄灭直径15 cm和20 cm的小尺寸油盘火,对直径25 cm中尺寸油盘火的灭火机理为冷却,对直径为30cm和35 cm大尺寸油盘火的灭火机理为窒息;脉冲细水雾能够熄灭不同尺寸的油盘火,且灭火效率高,火焰熄灭均发生在喷头暂停喷水期间,灭火机理为水雾蒸发稀释氧气而窒息。     

细水雾对油池火热释放速率影响规律的实验研究

热释放速率是描述火灾现象的重要参数,可以表征火灾发展的强烈程度。利用大尺寸的热释放速率实验测量平台开展细水雾对不同种类油池火灭火效率的实验研究,同时分析细水雾对燃烧产物一氧化碳含量的影响。结果表明,热释放速率曲线能直接反映出细水雾对火源的作用,细水雾作用下三种燃料的热释放速率均被有效抑制,且细水雾的流量越大,对油池火的灭火效果越好。燃烧产物一氧化碳在施加细水雾时出现陡增,表明细水雾隔绝氧气,造成不完全燃烧或者燃烧熄灭。     

A study of the probability distribution of pool fire extinguishing times using water mist

Water mist, a replacement for Halon gaseous agents in fire fighting, has been studied for decades. However, the fire-extinguishing reliability of water mist is debated. For example, there are significant differences in extinguishing times between tests conducted under the same conditions, and water mists have difficulty extinguishing small fires. To date, no study of the probability distribution of extinguishing times has been reported. In this study a statistical analysis of the extinguishing time distribution of pool fires extinguished using water mist is presented. The fire sources were circular/square stainless steel pans with gasoline, diesel, ethanol or daqing RP-3 as fuel. Two types of extinguishing scenarios were observed. In one situation, the fire was extinguished via a blow off process, when the flames had not yet been suppressed. Flame cooling is the primary fire extinguishing mechanism; the mass loss rate and combustion heat of the fuel are two key factors. In the other situation, the fire was initially suppressed and subsequently extinguished after a long suppression stage. Surface cooling is the primary fire extinguishing mechanism; the flash point of the fuel is the key factor.     

细水雾灭垂直立面火实验研究

对细水雾灭垂直立面火进行了实验研究。结果表明,喷头和火源之间存在一个最佳的水平距离,在此距离上,细水雾能够扑灭的火源尺寸或火源的位置范围最大。喷头向燃料表面垂直喷射时,灭火时间最短。斜向喷射时,随着喷射角度的增大,灭火时间逐渐增大,直至灭火失败。喷头斜向上喷射时的灭火效果优于斜向下喷射时的灭火效果,能够在更大的喷射距离上扑灭相同规模的火源。     

Experimental study on the mitigation via an ultra-fine water mist of methane/coal dust mixture explosions in the presence of obstacles

In this paper, experimental investigations were performed for the mitigation via an ultra-fine water mist of methane/coal dust mixture explosions in the presence of obstacles to reveal the effects of the obstacles in this scenario. Two PCB piezo-electronic pressure transducers were used to acquire the pressure history, a Fastcam Ultima APX high-speed video camera was used to visualize both the process of the mixture explosion and its mitigation. The diameters of the coal dust, the types of obstacles and the volumes of ultra-fine water mist were varied in the tests. The parameters of the explosion overpressure and the range of critical volume flux of the ultra-fine water mist for explosion mitigation were determined. The results show that the mixture explosion and its mitigation are primarily influenced by the number, shape and set locations of the obstacles. When the volume flux of the water mist is larger than a certain amount, the mixture explosions and the effects of obstacles can be completely mitigated with the ultra-fine water mist.     

受限空间脉冲细水雾系统关键参数试验与数值模拟研究

为了研究脉冲细水雾的关键参数,采用FDS软件对不同周期的脉冲细水雾熄灭受限空间油盘火进行了数值模拟,分析了脉冲周期的优化设置、细水雾的灭火效果和灭火机理。根据模拟结果进行参数设置,建立了脉冲细水雾试验平台,对脉冲细水雾熄灭不同尺寸油盘火进行了试验研究,并与数值模拟结果对比。研究表明:脉冲细水雾的最佳周期应满足喷头开启时间接近雾滴降至燃料表面的时间,暂停时间接近雾滴的生存时间;脉冲细水雾能熄灭不同尺寸火源,其灭火效果优于连续细水雾,雾滴蒸发效率更高,灭火机理为水雾蒸发稀释氧气而窒息灭火。