Hydrogen sulfide removal by iron containing activated carbon

Activated carbon modified by impregnation with iron (III) chloride solution (Fe‐ACs) were studied to try to raise their adsorption capacity for hydrogen sulfide, a malodorous substance.

The surface area and pore volume of activated carbon were decreased by impregnation, but the amount of hydrogen sulfide adsorbed onto Fe‐AC was larger than that onto raw activated carbon (R‐AC). In particular, a large increase of the amount adsorbed onto Fe‐AC was noted at low equilibrium pressure. It was assumed that the increase of amount of hydrogen sulfide adsorbed onto Fe‐AC was due to the chemical interaction between iron (III) chloride on the pores in addition to the physical adsorption onto pores of activated carbon. Fe‐AC shows a high selectivity for hydrogen sulfide.     

活性炭吸附-介质阻挡放电等离子体处理五氯酚

研究了介质阻挡放电(DBD)与活性炭(AC)吸附相结合用于高浓度五氯酚(PCP)废水的处理.含有高浓度的PCP溶液被富集在AC上,通过DBD等离子体降解吸附在AC上的PCP,并且实现AC的循环再利用.主要考察了DBD等离子体作用条件下AC上PCP的降解效果以及3次循环处理后AC吸附等温线的变化.结果表明:随着放电电压和处理时间的增加,AC上PCP的降解效率增加,较高的电源频率有助于PCP的降解,而且经过3次吸附/处理循环后,AC仍然具有较高的吸附能力.     

Influence of environmental temperature and relative humidity on photocatalytic oxidation of toluene on activated carbon fibers coated TiO

TiO₂ supported on active carbon fiber (TiO₂/ACF), an absorbable photocatalyst, is a new kind of material applied in air purification. In this paper, the influence of environmental temperature (T) and relative humidity (RH) on the gas-solid adsorption of toluene and the photocatalytic oxidation (PCO) efficiency of adsorbed toluene on TiO₂/ACF were studied, and then, the purification capability of TiO₂/ACF was estimated. PCO results showed that although the PCO efficiency increased under high RH and T levels, the amount of adsorption of toluene decreased. Moreover, quantitative analysis results of intermediates indicated that more environmental risk emerged when PCO of toluene was carried out at higher environmental T and RH levels because more toxic intermediates would be accumulated on the TiO₂/ACF. So, it is significant to control the environmental T and RH conditions in the application of the PCO technique. T = 25°C and RH = 30% is the optimal condition for purifying toluene in our experimental system.     

Influence of environmental temperature and relative humidity on photocatalytic oxidation of toluene on activated carbon fibers coated TiO2

TiO₂ supported on active carbon fiber (TiO₂/ACF), an absorbable photocatalyst, is a new kind of material applied in air purification. In this paper, the influence of environmental temperature (T) and relative humidity (RH) on the gas-solid adsorption of toluene and the photocatalytic oxidation (PCO) efficiency of adsorbed toluene on TiO₂/ACF were studied, and then, the purification capability of TiO₂/ACF was estimated. PCO results showed that although the PCO efficiency increased under high RH and T levels, the amount of adsorption of toluene decreased. Moreover, quantitative analysis results of intermediates indicated that more environmental risk emerged when PCO of toluene was carried out at higher environmental T and RH levels because more toxic intermediates would be accumulated on the TiO₂/ACF. So, it is significant to control the environmental T and RH conditions in the application of the PCO technique. T = 25°C and RH530% is the optimal condition for purifying toluene in our experimental system.     

Granulation of gibbsite with inorganic binder and its ability to adsorb Mo(VI) from aqueous solution

In this study, we prepared a new adsorbent and evaluated its ability to adsorb Mo(VI). Gibbsite was granulated with colloidal alumina or colloidal silica. The amount of Mo(VI) adsorbed onto granular gibbsite with a binder, effect of contact time and pH on the adsorption of Mo(VI), and column experiments were investigated. The amount of Mo(VI) adsorbed was greater in the order of ST12 (colloidal silica, 12%)?相似文献   

Insight into the promotion mechanism of activated carbon on the monolithic honeycomb red mud catalyst for selective catalytic reduction of NOx

• Activated carbon was proposed to be an efficient accelerant for molded red mud catalyst. • The surface acidity and reducibility were highly improved, as well as the pore structure. • The enrichment of the surface Fe²⁺ and the adsorbed oxygen account for the improvement. Our previous study proved that the acid-pretreatment process could efficiently activate red mud (RM) for the selective catalytic reduction (SCR) of NO_x. However, in terms of the molding process, which is the key step determining whether it can be applied in large-scale industrial, the surface acidity and reducibility of catalyst always decreased dramatically, and part of surface area and pore structure were lost. In this study, we prepared monolithic honeycomb red mud (MHRM) catalysts with activated carbon (AC) as an accelerant and investigated the effect of AC on the MHRM. The results showed that the MHRM with 3 wt.% of AC (MHRM-AC3) exhibited the best SCR performance, and kept more than 80% NO_x conversion in the range of 325°C–400°C. Compared with the MHRM, MHRM-AC1, and HMRM-AC5, the MHRM-AC3 has more mesoporous and macroporous structures, which can provide more adsorption active sites. The AC significantly improved NH₃ adsorption and surface reducibility, which was mainly due to the increase of the surface acid sites (especially the Brönsted acid sites), the concentration of Fe(II), and the surface adsorbed oxygen. The presence of more Fe(II) enriched the surface oxygen vacancies, as well as the surface adsorbed oxygen, due to the charge imbalance and unsaturated chemical bond. And surface adsorbed oxygen exhibited more active than lattice oxygen owing to its higher mobility, which was conducive to NO_x reduction in the SCR reaction.     

Indigo carmine removal by charcoal from rice bran as an agricultural by-product

On the utilization of agricultural by-product, charcoal from rice bran was produced. The adsorption characteristics of indigo carmine onto charcoals from rice bran were investigated by the batch method. The yield and surface area of charcoal were decreased and increased with increase of carbonization temperature, respectively. The removal ratio of indigo carmine was high with the charcoal carbonized at higher temperature. In the relationship between the amount of indigo carmine adsorbed and the square root of elapsed time, a good linearity was recognized. The kinetic constant of adsorption removal for indigo carmine was rapid in the charcoal carbonized at higher temperature. The adsorption characteristics for indigo carmine removal by charcoal from rice bran were dominated by the value of their surface area.     

Accelerating effect of sodium chloride on mexiletine adsorption onto activated charcoal

The effective use of activated charcoal as an oral adsorbent for primary treatment of acute poisoning was investigated in vitro by evaluating the characteristics of mexiletine, an anti-arrhythmic drug, adsorbed onto activated charcoal in the presence of sodium chloride solutions at various concentrations. The equilibrium amount of mexiletine adsorbed onto activated charcoal was increased by the addition of sodium chloride. In particular, there was a marked increase in the amount adsorbed from a solution of lower mexiletine concentration. The removal rate is another important factor in the evaluation of activated charcoal, and a rapid decrease of mexiletine concentration by the addition of sodium chloride was recognized. The acceleration of mexiletine adsorption onto activated charcoal by the addition of sodium chloride was due to the occurrence of salting-out. It could be concluded that the administration of activated charcoal suspended in saline solution was more effective in the primary treatment of acute poisoning by mexiletine overdose.     

Thermodynamics of tetracycline adsorption on silica

The adsorption of antibiotic tetracycline onto silica particles was investigated. The effects of pH, electrolyte concentration and temperature on the adsorption equilibrium were examined and the data correlated with a dual site adsorption model. Adsorption of tetracycline onto approximately 9% of the adsorption sites was found to be irreversible, whereas the rest exhibited Langmuir behaviour. Increasing pH of the solution had a strong negative effect on the adsorbed amounts. Adsorption decreased also with increasing ionic strength and temperature. The enthalpy and entropy of adsorption were found to be approximately −16 and −25 J/mol, respectively.     

Characteristics of carbonyls and volatile organic compounds (VOCs) in residences in Beijing,China

Volatile organic compounds (VOCs) and carbonyl compounds were measured both indoors and outdoors in 50 residences of Beijing in heating (December, 2011) and non-heating seasons (April/May, 2012). SUMMA canisters for VOCs and diffusive samplers for carbonyl compounds were deployed for 24 h at each site, and 94 compounds were quantified. Formaldehyde, acetone and acetaldehyde were the most abundant carbonyl compounds both indoors and outdoors with indoor median concentrations being 32.1, 21.7 and 15.3 μg·m⁻³, respectively. Ethane (17.6 μg·m⁻³), toluene (14.4 μg·m⁻³), propane (11.2 μg·m⁻³), ethene (8.40 μg·m⁻³), n-butane (6.87 μg·m⁻³), and benzene (5.95 μg·m⁻³) showed the high median concentrations in indoor air. Dichloromethane, p-dichlorobenzene (p-DCB) and toluene exhibited extremely high levels in some residences, which were related with a number of indoor emission sources. Moreover, isoprene, p-dichlorobenzene and carbonyls showed median indoor/outdoor (I/O) ratios larger than 3, indicating their indoor sources were prevailing. Chlorinated compounds like CFCs were mainly from outdoor sources for their I/O ratios being less than 1. In addition, indoor concentrations between two sampling seasons varied with different compounds. Carbonyl compounds and some chlorinated compounds had higher concentrations in the non-heating season, while alkanes, alkenes, aromatic compounds showed an increase in the heating season. Indoor concentration of VOCs and carbonyls were influenced by locations, interior decorations and indoor activities, however the specific sources for indoor VOCs and carbonyls could not be easily identified. The findings obtained in this study would significantly enhance our understandings on the prevalent and abundant species of VOCs as well as their concentrations and sources in Beijing residences.     

Adsorption property of direct fast black onto acid-thermal modified sepiolite and optimization of adsorption conditions using Box-Behnken response surface methodology

The adsorption of direct fast black onto acid-thermal modified sepiolite was investigated. Batch adsorption experiments were performed to evaluate the influences of experimental parameters such as initial dye concentration, initial solution pH and adsorbent dosage on the adsorption process. The three-factor and three-level Box-Behnken response surface methodology (RSM) was utilized for modeling and optimization of the adsorption conditions for direct fast black onto the acid-thermal modified sepiolite. The raw sepiolite was converted to acid-thermal modified sepiolite, and changes in the fourier transform infrared spectrum (FTIR) adsorption bands of the sample were noted at 3435 cm^-1 and 1427 cm^-1. The zeolitic water disappeared and the purity of sepiolite was improved by acid-thermal modification. The decolorization rate of direct fast black adsorbed increased from 68.2% to 98.9% on acid-thermal modified sepiolite as the initial solution pH decreased from 10 to 2. When the adsorbent dosage reached to 2.5 g·L^-1, 2.0 g·L^-1, 1.5 g·L^-1 and 1.0 g·L^-1, the decolorization rate was 90.3%, 86.7%, 61.0% and 29.8%, respectively. When initial dye concentration increased from 25 to 200 mg·L^-1, the decolorization rate decreased from 91.9% to 60.0%. The RSM results showed that the interaction between adsorbent dosage and pH to be a significant factor. The optimum conditions were as follows: the adsorbent dosage 1.99 g·L^-1, pH 4.22, and reaction time 5.2 h. Under these conditions, the decolorization rate was 95.1%. The three dimensional fluorescence spectra of direct fast black before and after treatment showed that the direct fast black was almost all adsorbed by the acid-thermal modified sepiolite.     

吸附模式对有机物光催化降解的影响2.H-酸在TiO2表面的光催化降解途径

水溶液中H-酸通过磺酸基团吸附在TiO2表面,UV照射TiO2所产生的自由基首先进攻吸附在TiO2表面的磺酸基团,从而进一步导致萘环开环.pH 2.5条件下,虽然饱和吸附量较大,但由于H-酸仅通过一个磺酸基团吸附在TiO2表面,过程中产生的硫酸根速率较慢,最终的光降解速率也较慢.pH 5.0条件下,虽然饱和吸附量较小,但由于吸附在TiO2表面的两个磺酸基团同时受到来自TiO2表面自由基的进攻,过程中产生的硫酸根速率较快,最终的光降解速率也较快.吸附模式的差异是导致H-酸在不同pH值条件下光催化降解途径和速率差异的关键因素.     

吸附模式对有机物光催化降解的影响1.H-酸在TiO2表面的吸附模式

H-酸萘环上含有的两个磺酸基团,在水溶液中可以解离一个或者两个.pH 2.5条件下,主要有一个磺酸基团解离,此时,H-酸通过一个磺酸基团吸附在TiO2表面,占位小,饱和吸附量大,但吸附键较弱,吸附较可逆.pH 5.0条件下,主要有两个磺酸基团解离,此时,H-酸通过两个磺酸基团吸附在TiO2表面,占位大,饱和吸附量小,但吸附键较强,吸附不可逆性较强.这种吸附模式的差异是导致H-酸在不同pH条件下饱和吸附量和吸附不可逆性差异的根本原因,也是导致不同pH条件下H-酸具有不同光催化降解途径的重要原因.     

Mg-Al型水滑石对水溶液中F-的吸附

采用水热法合成Mg-Al型水滑石(LDHs),研究LDHs及其焙烧产物C-LDHs对水溶液中F-的吸附行为,并用X射线衍射和热重分析对LDHs,C-LDHs以及吸附F-后的C-LDHs(R-LDHs)的结构和性质进行了表征. 结果表明:LDHs对水溶液中的F-基本没有吸附,而C-LDHs对F-有较大的吸附容量,同时,酸性的增强有利于C-LDHs对F-的吸附. C-LDHs对F-吸附4h后可达到吸附平衡. 通过吸附F-,C-LDHs的结构由吸附前的混合氧化物固溶体恢复到层状结构, 表明C-LDHs对水溶液中F-的高吸附性能是因为其具有较强的"记忆效应".     

吸附反应时间对除草剂阿特拉津吸附行为的影响

采用批量动态实验方法,对潮土中阿特拉津吸附特征随吸附反应时间变化进行了研究。结果表明,土壤吸附的阿特拉津量随反应时间的变化符合双曲线函数关系。在50μg·L-1～2000μg·L-1浓度系列下,在48h内,土壤颗粒对阿特拉津的吸附属于快反应,土壤吸附的阿特拉津量随吸附反应时间呈指数上升,为吸附实验结束(168h)时土壤吸附阿特拉津总量的58%到90%。当吸附反应时间超过48h后,随反应时间增加,土壤吸附阿特拉津量差异变化不显著。阿特拉津在潮土颗粒和土壤溶液中的相分配可用Freundlich方程描述。吸附容量因子Kf与吸附反应时间之间有极显著的线性正关系(r2=0.9063**,p<0.0001)。无量纲的非线性因子n与吸附反应时间之间也具有显著的线性负关系(r2=0.5666*,p=0.0192)。     

黄浦江底泥对多环芳烃吸附机理的研究

本文主要介绍黄浦江底泥对以蒽为代表性物质的多环芳烃的吸附研究，着重探讨其吸附机理，在实验条件下，黄浦江底泥对蒽的吸附属多分子层吸附，可用ｄｅ ＢｏｅｒＺｗｉｋｋｅｒ公式所表示的极化模型较好地描述，这表明原描述非极性气相分子在极性吸附剂上吸附的多分子层极化模型可应用于稀溶液中溶剂化蒽分子在极性吸附剂上的吸附过程，本研究认为吸附等温线上出现阶梯状形式是由于蒽－甲醇分子的溶剂作用及底泥颗粒的表面不均匀性     

Formation of secondary inorganic aerosol in a frigid urban atmosphere

•Harbin showed relatively high threshold RH (80%) for apparent increase of SOR. •The observed SOR were at the lower end of the ratios from Beijing’s winter. •Temperature-dependent increase of NOR was sharper than that of SOR. • NOR increased with stronger biomass burning impact but SOR was largely unchanged. Formation of secondary inorganic aerosol (SIA) was investigated during a six-month long heating season in Harbin, China. Enhanced sulfate formation was observed at high relative humidity (RH), with the same threshold RH (80%) for both colder and warmer measurement periods. Compared to wintertime results from Beijing, the threshold RH was considerably higher in Harbin, whereas the RH-dependent enhancement of sulfur oxidation ratio (SOR) was less significant. In addition, the high RH events were rarely encountered, and for other periods, the SOR were typically as low as ~0.1. Therefore, the sulfate formation was considered inefficient in this study. After excluding the several cases with high RH, both SOR and the nitrogen oxidation ratio (NOR) exhibited increasing trends as the temperature increased, with the increase of NOR being sharper. The nitrate to sulfate ratio tended to increase with increasing temperature as well. Based on a semi-quantitative approach, this trend was attributed primarily to the temperature-dependent variations of precursors including SO₂ and NO₂. The influence of biomass burning emissions on SIA formation was also evident. With stronger impact of biomass burning, an enhancement in NOR was observed whereas SOR was largely unchanged. The different patterns were identified as the dominant driver of the larger nitrate to sulfate ratios measured at higher concentrations of fine particulate matter.     

高岭土界面Fe(Ⅱ)吸附与邻硝基苯酚还原转化的交互反应研究

研究了高岭土界面亚铁吸附与邻硝基苯酚(2-nitrophenol,2-NP)还原转化的交互作用.考察了反应pH值、界面吸附铁密度、反应温度(T)对2-NP的还原动力学的影响.结果表明,吸附态Fe(Ⅱ)为2-NP还原转化的关键物种,高龄土界面Fe(Ⅱ)吸附能明显提高还原反应的反应速率.2-NP的还原转化速率常数(k)随着反应pH值的升高、吸附铁密度的增加、反应温度的升高而增大,ln k与pH、吸附铁密度、1/T都具有明显的线性关系.2-NP还原转化的活化能为87.15 kJ·mol-1,吸附反应的活化能为18.5 kJ·mol-1.该研究可为土壤矿物界面物理化学与氧化还原的交互反应过程研究提供借鉴.     

A sandy loam soil as a natural control for Pb contamination

The Pb (II) adsorption/desorption mechanism onto a natural sandy loam soil was studied by batch experiments at different pHs (3.0, 4.5, 6.0), at different ionic strength (0, 0.02 and 0.1 M) and with different electrolytes solutions of NaCl, NaAcO and NaNO₃. Pb was strongly adsorbed onto the soil due to the formation of a mix of inner-sphere and outer-sphere complexes. Experimental adsorption data fitted Freundlich and Langmuir isotherms. The desorption results with 0.1 M Mg (NO₃)₂ and 0.1 M NaAcO solutions corroborated the mechanisms proposed. The strong binding of Pb (II) to high affinity sites on soil minerals seems to be responsible for the extent of hysteresis. The sandy loam soil under study thus constitutes a natural control for Pb contamination.     

海泡石黏土矿物对Cu2+的吸附动力学研究

研究分析了海泡石黏土矿物对铜离子的吸附性能和动力学特征,结果表明,海泡石黏土矿物对Cu~(2 )吸附的最佳pH值为6.0左右,随着pH值的增大,吸附作用减弱;在[Cu~(2 )]=100mg·l~(-1),溶液pH值为6,吸附时间为2h时,添加0.1 g海泡石,海泡石对Cu~(2 )的吸附去除率仅为39.5%,当海泡石用量提高至0.4 g时,其对Cu~(2 )的吸附去除率提高到94.8%;实验结果同样显示,18min内有90%的Cu~(2 )被海泡石吸附,随着吸附时间的增加,吸附作用趋于稳定,2h可达到吸附平衡。该吸附过程符合Langmuir和Freundlich等温吸附方程.同时,分别采用拟一级模型和拟二级模型考察了吸附动力学,并计算了这些动力学模型的速率常数.实验数据和拟二级模型计算结果之间有较好的相关性.