三氧化二铝超细粉末对水中三氯乙烯吸附特性研究

探讨了γ-Al2O3超细粉末吸附人工配制的废水中三氯乙烯(TCE)的吸附等温线、吸附动力学及热力学。结果表明:Al2O3对TCE的吸附能力随温度的升高而显著增强;TCE在Al2O3表面的吸附层数为0.68层;Langmuir、Freundlich和deBoer-Zwikker公式都可以用来描述Al2O3吸附TCE的吸附等温线;Al2O3对TCE的吸附符合拟二级动力学方程,吸附反应的活化能为14.75 kJ.mol-1,吸附焓为8.87 kJ.mol-1,属于自发的吸热反应。     

糠醛渣对水中甲基橙的吸附性能

为了探究糠醛生产中的废料糠醛渣对水体中甲基橙的吸附性能和吸附机制,利用FT-IR（傅里叶变换红外光谱）和SEM（扫描电镜）对糠醛渣的结构特性进行表征,浅析糠醛渣对甲基橙的吸附机制;通过模拟试验,考察了吸附剂用量、pH、吸附时间和温度等因素对糠醛渣吸附甲基橙过程的影响;采用吸附动力学模型和吸附等温模型,进一步探讨了糖醛渣吸附机制.结果表明:①糠醛渣结构疏松多孔,表面具有丰富的官能团,有利于吸附.②糠醛渣能高效吸附水中甲基橙,在温度为293 K、pH为4~9、吸附剂用量为0.2 g时,糠醛渣对400 mg/L的甲基橙吸附效果最好;吸附过程在60 min左右达到平衡,并且较好地符合准二级动力学模型（R2=0.999 9）;吸附量随温度的升高而减少,表明该吸附过程为放热过程;在293 K时最大理论吸附量为54.35 mg/g,吸附数据更符合Langmuir吸附等温模型（R2=0.993 3）,表明糠醛渣对甲基橙的吸附主要为单层吸附.③糠醛渣可再生重复利用,吸附甲基橙后的糠醛渣用0.1 mol/L氢氧化钠溶液进行解吸再生试验,第5次使用时对甲基橙仍然具有较好的吸附效果.研究显示,糠醛渣在室温条件下、较宽的pH范围内能快速高效地吸附水中的甲基橙,并且重复利用性好,是一种在偶氮染料废水处理中具有发展前景的廉价、可再生生物质吸附材料.      

活性焦对垃圾渗滤液中难降解有机物的吸附及影响因素研究

垃圾渗滤液经预处理后与城市污水混合进行生物处理是较为有效的方法,但垃圾渗滤液中含大量难降解有机物,严重影响了城镇污水处理厂出水COD.因此,需强化垃圾渗滤液预处理过程,使其适用于生物处理.本研究采用活性焦吸附某垃圾焚烧发电厂垃圾渗滤液,发现活性焦对垃圾渗滤液中COD、色度、恶臭、TOC、TN等均具有良好的处理效果.通过对吸附性能的影响因素研究发现,活性焦种类、投加量、p H和吸附时间均会影响吸附效果,最佳活性焦投加量为20 g·L~(-1),酸性条件更有利于吸附,渗滤液中COD的去除主要发生在吸附过程的前1 h.活性焦吸附可提高垃圾渗滤液的可生化性,主要吸附垃圾渗滤液中难降解芳香族大分子有机物,其中,对溶解性有机物中疏水性有机酸组分的吸附效果最佳,使其出水适用于生物处理,从而保证污水处理厂COD可以稳定达标排放.     

生物炭吸附水中磷酸盐的研究进展

生物炭作为1种环境友好型吸附材料,可有效去除并回收水体中的磷,由此也成为当前的研究热点之一。综述了目前国内外生物炭吸附磷酸盐及磷素回收研究现状,主要总结了控制生物炭吸附磷酸盐的4种主要机制,阐述了影响生物炭吸附除磷过程中的主要影响因素,介绍了目前应用研究的方向并提出生物炭在实际应用中所面临的问题并对未来研究方向进行了展望,以期为未来研究及推广应用提供理论支撑。     

硝酸活化活性炭吸附水中阿莫西林的研究

研究了吸附时间、初始阿莫西林浓度和初始pH对硝酸活化活性炭吸附水中阿莫西林的影响,并根据吸附时间和初始阿莫西林浓度的变化探讨了活化活性炭吸附水中阿莫西林的动力学和吸附等温线模型。结果表明,常温下,对初始阿莫西林浓度分别为50.0和200.0 mg/L的溶液,0.100 0 g活化活性炭在60 min可达吸附平衡;初始pH为4~6时吸附效果较好;当初始阿莫西林浓度为193.7 mg/L,pH为4.05,0.100 0 g活化活性炭吸附60 min时,阿莫西林的吸附率为78.79%,吸附量为71.4 mg/g;活化活性炭吸附阿莫西林较符合Freundlich吸附等温线;伪二级动力学模型能较好地描述活化活性炭对水中阿莫西林的吸附动力学。     

强化一级处理污泥的吸附性能研究

强化一级处理污泥对以ＣＯＤ和ＳＣＯＤ表示的有机物质具有较大的吸附量。其吸附等温线和解吸等温线既符合Ｆｒｅｕｎｄｌｉｃｈ型,也符合Ｌａｎｇｍｕｉｒ型,但解吸不完全。     

载镁生物炭对水体中磷酸盐和植酸的吸附性能及机理分析

水体中磷的大量存在引发了水体富营养化,导致水质逐步恶化、黑臭。为了有效处理水体中的磷(主要有磷酸盐和植酸类),采用成熟竹子为原料、氯化镁为改性剂,以氮气热解法制备载镁生物炭,对水体中磷进行吸附研究,同时实现对生物炭的资源化利用。通过载镁生物炭对无机、有机磷在水体中的动力学实验和解析实验,并结合X射线衍射、扫描电镜、傅里叶变换红外光谱等技术研究了载镁活性炭对磷酸盐及植酸的吸附性能及机理。结果表明:载镁生物炭对两种类型磷的吸附量较单一生物炭均显著提高,对磷酸盐和植酸的吸附平衡量分别达到105,165 mg/g。载镁生物炭对2种磷的吸附动力学均符合准二级动力学拟合方程,吸附等温线符合Langmuir和Freundlich方程,其对有机磷植酸的最大吸附量高于磷酸盐,吸附过程受多种机理共同作用,以化学沉淀吸附为主。此外,吸附过程中载镁生物炭分别与磷酸盐、植酸生成了针状的磷酸镁水合物和非晶态的含镁磷的复合物。     

改性橘子皮对水中高氯酸盐及共存阴离子的竞争吸附研究

模拟多种阴离子共存的水体环境,采用氨基改性处理后的橘子皮作为吸附剂,研究其在不同离子共存条件下对高氯酸盐的竞争吸附.分析在不同pH条件下,竞争性阴离子对高氯酸盐吸附的影响;探讨单、双组分体系下的热力学、动力学吸附机理;采用红外光谱分析(FTIR)表征不同竞争吸附条件下吸附剂材料的结构特征.结果表明,不同pH范围内,3种阴离子与Cl O-4发生竞争吸附,其影响顺序不同:pH3时,其影响顺序为SO2-4NO-3PO3-4;3pH10时,其影响顺序为SO2-4PO3-4NO-3;pH10时,3种阴离子对Cl O-4吸附的影响趋于相同.单组分吸附下,改性橘子皮对Cl O-4、NO-3、SO2-4、PO3-4的最大吸附量分别为217.72、134.97、89.9、65.79 mg·g-1;竞争条件下,共存阴离子对Cl O-4吸附的影响顺序为PO3-4SO2-4NO-3,并且改性橘子皮对Cl O-4的吸附符合Freundlich等温线模型及准二级动力学模型,表明化学吸附为吸附的主要速率控制步骤.红外光谱分析结果证明了NO-3、SO2-4、PO3-4均在改性橘子皮吸附Cl O-4的过程中发生了竞争吸附.     

不同营养水平沉积物在不同pH下对磷酸盐的等温吸附特征

研究了不同营养水平沉积物在不同pH下对磷酸盐的吸附等温线,分别采用了线性和非线性2种方法拟合吸附等温线,并分析比较了2种方法的适用性.结果表明:①不同营养水平沉积物对磷酸盐的吸附量在接近中性时最大,酸性和碱性条件下均下降,污染严重的沉积物对磷酸盐的吸附受pH影响较污染轻的大;②不同pH下,不同营养水平沉积物对磷酸盐的吸附等温线没有明显规律;③沉积物对磷酸盐的吸附行为采用线性和非线性拟合均存在不足,不能仅仅根据R2和X2的大小进行拟合方程的适用性比较;④为了获得更为真实可靠的拟合结果,可以利用线性和非线性方法分别进行拟合,而每一种拟合方法也要同时采用多种拟合方程,在对多个拟合结果比较的基础上确定更符合实验数据的拟合方程.      

磁性硅藻土负载纳米过氧化钙对水中磷酸盐吸附

本研究以磁性硅藻土为载体,负载纳米过氧化钙(CaO₂),制备了一种可高效吸附磷酸盐且可回收的复合材料(MDCP),并利用SEM、EDX-mapping、XRD、XDS和VSM等技术对MDCP的微观形貌、内部结构、晶体组成以及元素组成进行了表征.结果表明,MDCP表面成功负载了CaO₂,并具有良好的磁性. MDCP对水中磷酸盐的吸附数据符合Langmuir等温吸附模型,根据Langmuir模型确定当T=20℃时MDCP对水中磷酸盐的最大单位吸附容量为191. 84 mg·g^-1.吸附等温线与吸附动力学的结果表明,MDCP对磷酸盐的吸附过程属于化学吸附. pH对MDCP吸附磷酸盐具有显著的影响,MDCP对磷酸盐的有效吸附pH范围为4～10,且MDCP对溶液pH具有调节效果,可使溶液pH保持在7～9的水平.当溶液共存Cl-、SO₄^2-、CO3_<sup>2-、HCO₃^2-、F-和NO₃<...     

Organic pollutants removal from 2,4,6-trinitrotoluene （TNT） red water using low cost activated coke

2,4,6-trinitrotoluene (TNT) red water from Chinese explosive industry was adsorbed by activated coke (AC) from lignite. Since the composition of TNT red water was very complicated, chemical oxygen demand (COD) was used as the index for evaluating the treatment efficiency. This study focused on the sorption kinetics and equilibrium sorption isotherms of AC for the removal of chemical oxygen demand (COD) from TNT red water, and the changes of water quality before and after adsorption were evaluated by using high performance liquid chromatograph (HPLC), UV-vis spectra and Gas Chromatography/Mass Spectroscopy (GC/MS). The results showed that the sorption kinetics of adsorbing COD from TNT red water onto AC was fitted well with the pseudo-second order model. The adsorption process was an exothermic and physical process. The sorption isotherm was in good agreement with Redlich–Peterson isotherm. At the conditions of initial pH, 20℃ and 3 hr of agitation, when the AC dosage was 160 g L-1, 64.8% of COD could be removed. The removal efficiencies of 2,4-dinitrotoluene-3-sulfonate (2,4-DNT-3-SO3-) and 2,4-dinitrotoluene-5-sulfonate (2,4-DNT-5-SO3-) were 80.5% and 84.3%, respectively. After adsorption, the acute toxicity of TNT red water reduced 81.8%, compared with that of unprocessed TNT red water.     

Influence of moderate pre-oxidation treatment on the physical, chemical and phosphate adsorption properties of iron-containing activated carbon

A novel adsorbent based on iron oxide dispersed over activated carbon(AC) were prepared, and used for phosphate removal from aqueous solutions. The influence of pre-oxidation treatment on the physical, chemical and phosphate adsorption properties of iron-containing AC were determined. Two series of ACs, non-oxidized and oxidized carbon modified by iron(denoted as AC-Fe and AC/OFe), resulted in a maximum impregnated iron of 4.03% and 7.56%, respectively. AC/O-Fe showed 34.0%–46.6% higher phosphate removal efficiency than the AC-Fe did. This was first attributed to the moderate pre-oxidation of raw AC by nitric acid, achieved by dosing Fe(II) after a pre-oxidation, to obtain higher iron loading, which is favorable for phosphate adsorption. Additionally, the in-situ formed active site on the surface of carbon, which was derived from the oxidation of Fe(II) by nitric acid dominated the remarkably high efficiency with respect to the removal of phosphate. The activation energy for adsorption was calculated to be 10.53 and 18.88 kJ/mol for AC-Fe and AC/OFe, respectively. The results showed that the surface mass transfer and intra-particle diffusion were simultaneously occurring during the process and contribute to the adsorption mechanism.     

Application of activated carbon derived from scrap tires for adsorption of Rhodamine B

Activated carbon derived from solid hazardous waste scrap tires was evaluated as a potential adsorbent for cationic dye removal. The adsorption process with respect to operating parameters was investigated to evaluate the adsorption characteristics of the activated pyrolytic tire char (APTC) for Rhodamine B (RhB). Systematic research including equilibrium, kinetics and thermodynamic studies was performed. The results showed that APTC was a potential adsorbent for RhB with a higher adsorption capacity than most adsorbents. Solution pH and temperature exert significant influence while ionic strength showed little e ect on the adsorption process. The adsorption equilibrium data obey Langmuir isotherm and the kinetic data were well described by the pseudo second-order kinetic model. The adsorption process followed intra-particle di usion model with more than one process a ecting the adsorption process. Thermodynamic study confirmed that the adsorption was a physisorption process with spontaneous, endothermic and random characteristics.     

污泥基活性炭去除水中重金属离子效能与动力学研究

以城市污泥为主要原料制备了污泥基活性炭(SAC),考察了其对重金属离子的吸附去除效能和吸附动力学规律.并选择了2种商品活性炭(煤质炭,MAC和椰壳炭,YAC)作为对比,以初始浓度为50mg/L的Cu(II),Pb(II),Cd(II),Cr(VI)4种重金属离子为去除对象,分别进行了3种活性炭的表面理化性质分析及其对4种重金属离子的吸附试验.结果表明,SAC的比表面积和微孔容积仅为YAC和MAC的1/3~1/2,吸附速率也相对较慢,但其对Cu(II),Pb(II),Cr(VI),Cd(II)的平衡吸附量却远大于2种商品活性炭,分别为9.9,8.9,8.2,5.4mg/g,说明SAC表面的高酸性基团含量对重金属离子的吸附起到了关键作用;Langmuir与Freundlich吸附等温模型均能较好地拟合SAC对Cu(II)和Pb(II)的吸附,SAC对Cr(VI)的吸附过程更符合Langmuir模型,而SAC对于Cd(II)的吸附过程用Langmuir与Freundlich两个模型均不能较好地拟合,说明SAC表面缺少能够与Cd(II)发生反应的结合位点.     

从分子质量的变化分析有机物对GAC吸附内分泌干扰物(BPA)的影响

从分子质量分布的角度研究了水中有机物对颗粒活性炭(GAC)吸附双酚A(BPA)容量及吸附速率的影响.结果表明,相对于以去离子水为本底的BPA溶液来说,GAC吸附以滤后水、臭氧后出水和原水为本底的BPA溶液的Langmuir模型的最大吸附容量q_m值分别下降了29.95%、43.56%和44.44%,而其拟二级动力学模型的k₂值分别下降了43.05%、49.75%和56.38%.相对分子质量3 000以上,尤其是10 000以上的有机物堵塞GAC的二级微孔;3 000以下,尤其是1 000以下的有机物与BPA分子之间存在直接的竞争吸附,是导致GAC对BPA的吸附容量以及吸附速率下降的主要原因.     

活性炭对双溶质水溶液中痕量有机物的理想吸附

对活性炭吸附水中有机物的吸附等温线研究表明，由IAST理论推导的简化模型可更好地解释活性炭对存在一种主要溶质的双溶质体系中痕量溶质的理想吸附现象，并解释了Henry系数与主要溶质的平衡浓度之间不呈简单的反比关系这一现象。活性炭对含苯酚、苯胺溶液中的氯仿和四氯化碳的吸附实验结果与模型预测值相符。影响Henry系数的主要因素有单溶质溶液的Freundrich参数和主要溶质的平衡浓度。各参数的敏感度分析表明：单溶质溶液的Freundrich参数对活性炭吸附痕量有机物的影响要大于主要溶质的平衡浓度的影响。     

活性炭吸附二苯并呋喃的动力学

采用Norit RB1和Monolith两种活性炭吸附气相中低浓度的二苯并呋喃,测定了二苯并呋喃在2种活性炭上的吸附等温线和吸附动力学曲线,分析了气相主体浓度、温度和二苯并呋喃初始浓度等因素对固相有效扩散系数的影响.结果表明,Langmuir吸附等温线模型能够比较准确地描述二苯并呋喃在Norit-RB1和Monolith活性炭上的吸附相平衡;二苯并呋喃在活性炭上的吸附速率受固相扩散控制;固相有效扩散系数随温度的升高而增大,气相浓度和二苯并呋喃初始浓度对固相有效扩散系数影响较小.     

磷酸盐对土壤吸附一硫代砷的影响

通过设计批实验和表征分析,探究不同浓度的磷酸盐影响下,一硫代砷酸盐（MTA）在土壤上的吸附特征和机理.结果发现,Elovich动力学模型和Langmuir等温吸附模型可较好地拟合MTA在土壤中的吸附过程,相关系数R²分别为0.983和0.994,表明土壤吸附MTA发生在局部位置,吸附过程主要以非均相扩散为主,拟合所得最大单层吸附量为254.214mg/kg.MTA与磷酸盐共存时,随着溶液中磷酸盐初始浓度的增大,土壤对MTA的平衡吸附量逐渐下降,对磷酸盐的吸附量逐渐增大;SEM-EDS结果表明无论是否添加磷酸盐,反应后的土壤表面都能检测到少量As,但添加磷酸盐条件下土壤表面的As含量则相对较低,证实磷酸盐的存在降低了土壤对MTA的吸附;XRD结果表明MTA能与土壤中的铁铝矿物发生络合反应生成内球络合物－[2Al （H₂AsO₄）₃]、≡Al₂O₂AsO （SH）和－[2Fe （H₂AsO₄）₃],而磷酸盐会与土壤表面的羟基形成内球络合物,导致土壤对MTA的吸附能力减弱.     

Comparison of different phosphate species adsorption by ferric and alum water treatment residuals

As safe byproducts of drinking water treatment processes,ferric and alum water treatment residuals(FARs) have the potential to be new phosphate(P) immobilization materials.In this study,batch experiments were conducted to investigate and compare the adsorption characteristics of three P species by FARs.The results showed that the kinetic processes of different P species’ adsorption by FARs could be described by a pseudo second-order model.The ranking list of the initial adsorption rates with respect to different phosphates was pyrophosphate,phytate,orthophosphate,hexametaphosphate and glycerophosphate.Of the six models considered,the two-site Langmuir model most effectively described the adsorption characteristics of the various P species.Upon fitting the results,the maximum adsorption capacities were determined to be 40.24 mg/g for phytate,18.04 mg/g for pyrophosphate,17.14 mg/g for orthophosphate,15.86 mg/g for hexametaphosphate and 10.81 mg/g for glycerophosphate.In addition,the adsorption processes of the different P species were spontaneous endothermic processes and were favored at lower pH values.The pH dependency was found to be especially true for orthophosphate,where the adsorption capacity decreased by 1.22 mg/g with an increase in pH from 5 to 9.Fractionation of the adsorbed P species from the FARs demonstrated that Al-P and Fe-P were the dominating forms,constituting approximately 80%-90% of the total P fractions,which indicated that the adsorbed P species had a low leaching risk and could stably exist in the FARs.Therefore,the FARs could be effective in controlling pollution in water caused by different P species.