In situ stabilization of soil lead using phosphorus

In situ stabilization of Pb-contaminated soils can be accomplished by adding phosphorus. The standard remediation procedure of soil removal and replacement currently used in residential areas is costly and disruptive. This study was carried out to evaluate the influence of P and other soil amendments on five metal-contaminated soils and mine wastes. Seven treatments were used: unamended control; 2,500 mg of P/kg as triple superphosphate (TSP), phosphate rock (PR), acetic acid followed by TSP, and phosphoric acid (PA); and 5,000 mg of P/kg as TSP or PR. A significant reduction in bioavailable Pb, as determined by the physiologically based extraction test (PBET), compared with the control upon addition of P was observed in all materials tested. Increasing the amount of P added from 2,500 to 5,000 mg/kg also resulted in a significantly greater reduction in bioavailable Pb. Phosphate rock was equally or more effective than TSP or PA in reducing bioavailable Pb in four out of five soils tested. Preacidification produced significantly lower bioavailable Pb compared with the same amount of P from TSP or PR in only one material. Reductions in Pb bioavailability as measured by PBET were evident 3 d after treatment, and it may indicate that the reactions between soil Pb and P occurred in situ or during the PBET. No further reductions were noted over 365 d. X-ray diffraction data suggested the formation of pyromorphite-like minerals induced by P additions. This study suggests that P addition reduced bioavailable Pb by PBET and has potential for in situ remediation of Pb-contaminated soils.     

Treatment of contaminated soil with phosphorus and manganese oxide reduces lead absorption by Sprague-Dawley rats

This study was conducted to determine the extent of Pb absorption into young rats (Rattus norvegicus var. Sprague-Dawley) fed untreated Pb-contaminated soil or Pb-contaminated soil treated with two different sources of P and P + Mn oxide. Data were compared from an in vitro, physiologically based extraction test (PBET) with the animal data to support the validity of the in vitro test to assess bioavailable Pb from a treated Pb-contaminated soil. Soil with a total Pb concentration of 2290 mg kg(-1) was used. Rats were fed 19 different test diets for 21 consecutive days. The test diets represented 95 g AIN93G rat meal kg(-1) diet with varying proportions of silica sand or soil to provide low, medium, or high doses of Pb from either Pb acetate, treated, or untreated soil. Blood, liver, kidney, and bone Pb concentrations were examined. For all four tissues, Pb concentrations for the Pb acetate groups were significantly higher than concentrations for all the soil groups. In general, either triple superphosphate (TSP) or phosphate rock (PR) treatments resulted in significant reductions in tissue Pb concentrations compared with untreated soil. Blood and kidney Pb concentrations for the PR + Mn oxide group were significantly lower than those of the PR group at the low and high doses. Relative bioavailability of Pb, as measured in all tissues, was significantly reduced when comparing untreated with amended soil. Correlation between the in vitro and in vivo tests, based on bone and liver tissue, showed that the in vitro test is successful at predicting Pb bioavailability.     

In situ soil water extraction: a review

The knowledge of the composition and fluxes of vadose zone water is essential for a wide range of scientific and practical fields, including water-use management, pesticide registration, fate of xenobiotics, monitoring of disposal from mining and industries, nutrient management of agricultural and forest ecosystems, ecology, and environmental protection. Nowadays, water and solute flow can be monitored using either in situ methods or minimally invasive geophysical measurements. In situ information, however, is necessary to interpret most geophysical data sets and to determine the chemical composition of seepage water. Therefore, we present a comprehensive review of in situ soil water extraction methods to monitor solute concentration, solute transport, and to calculate mass balances in natural soils. We distinguished six different sampling devices: porous cups, porous plates, capillary wicks, pan lysimeters, resin boxes, and lysimeters. For each of the six sampling devices we discuss the basic principles, the advantages and disadvantages, and limits of data acquisition. We also give decision guidance for the selection of the appropriate sampling system. The choice of material is addressed in terms of potential contamination, filtering, and sorption of the target substances. The information provided in this review will support scientists and professionals in optimizing their experimental set-up for meeting their specific goals.     

In situ soil treatments to reduce the phyto- and bioavailability of lead, zinc, and cadmium

A study was established near a former Zn and Pb smelter to test the ability of soil amendments to reduce the availability of Pb, Zn, and Cd in situ. Soil collected from the field was amended in the lab with P added as 1% P-H3PO4, biosolids compost added at 10% (referred to hereafter as "compost"), and a high-Fe by-product (referred to hereafter as "Fe") + P-triple superphosphate (TSP) (2.5% Fe + 1% P-TSP) and incubated under laboratory conditions at a constant soil pH. Changes in Pb bioavailability were measured with an in vitro test and a feeding study with weanling rats. Field-amended and incubated soils using these plus additional treatments were evaluated using the in vitro extraction and tall fescue (Festuca arundinacea Schreb. cv. Kentucky-31) metal concentration. Reductions were observed across all parameters but were not consistent. In the feeding study, the 1% P-H3PO4 and compost treatments resulted in a decrease of 26% in rat tissue Pb concentration compared with the control soil. The 2.5% Fe + 1% P-TSP showed a 39% decrease. The 1% P-H3PO4 treatment caused the greatest reduction in in vitro extractable Pb from field samples (pH 2.2) with a measured reduction of 66%, while the compost treatment had a 39% reduction and the 2.5% Fe + 1% P-TSP treatment a 50% reduction. The in vitro extraction (pH 1.5) run on field samples showed no reduction in the compost or Fe treatments. The 1% P-H3PO4 treatment was the most effective at reducing plant Pb, Zn, and Cd.     

Modeling phosphorus concentrations in Irish rivers using land use, soil type, and soil phosphorus data

Modeling diffuse phosphorus (P) loss may indicate management strategies to minimize P loss from agricultural sources. An empirical model predicting flow-weighted phosphorus concentrations (MRP) was derived using data collected from 35 Irish river catchments. Monitoring records of riverine P and stream flow data were used to calculate MRP values averaged for the years 1991-1994. These data were modeled using land use, soil type, and soil P data. Soil type in catchments was described using soil survey classifications weighted according to their P desorption properties from laboratory results. Soil test P concentrations for the studied watersheds were obtained from a national database. Soil P levels were weighted based on the results of field experiments measuring P losses in overland flow from fields at different soil test P levels. The 35 catchments were statistically clustered into two populations (A and B) based on differences in soil type, specifically, soil hydrology. Catchments in Cluster A had predominantly poorly drained soils and comparatively higher MRP concentrations (0.03-0.17 mg L(-1)) than Cluster B areas (0.01-0.7 mg L(-1)) with mostly well-drained soils. Regression equations derived for A and B type catchments predicted MRP values with 68 and 62% of the variation explained in the models, respectively. Data extracted for the rest of the country were applied to the models to delineate areas at risk on a national scale. While the models were only moderately accurate they highlighted the influence of land management, specifically, high production grassland receiving high P inputs, in conjunction with the effect of soil type and soil hydrology on the transport of P to surface waters.     

In situ dynamics of phosphorus in the rhizosphere solution of five species

Root activity can modify the chemistry of the rhizosphere and alter phosphorus (P) availability and uptake. However, until recently, relatively little was known about the dynamics of soil solution P at the root surface because of our inability to measure in situ changes in solution P at the plant root. A mini-rhizotron experiment with corn (Zea mays L. cv. Stine 2250), soybean [Glycine max (L.) Merr. cv. Pioneer 3563), cottonwood (Populus deltoids L.), smooth brome (Bromus inermis Leyss.), and switchgrass (Panicum virgatum L.) was conducted to measure the spatial and temporal dynamics of P in the rhizosphere solution of a fine silty, P-rich calcareous soil (solid-phase total P concentration = 62 mg kg(-1), pH = 7.68) from western Iowa. Micro-suction cups were used to collect samples of soil solution from defined segments of the rhizosphere, and capillary electrophoresis (CE) was used to determine the P concentration of the soil solution. At the end of 10 d, a decreasing P concentration gradient in soil solution toward the root was observed in corn, cottonwood, and smooth brome. No clear rhizosphere effect was observed for soybean and switchgrass. Statistical analysis indicated significantly lower solution P concentrations in the rhizospheres of corn (p = 0.05), cottonwood (p = 0.01), and smooth brome (p = 0.01) compared with bulk soil solution. Results indicate that P depletion from rhizosphere soil solution depends on plant species. Under the conditions of this study, corn, cottonwood, and smooth brome were more effective in depleting solution P than soybean and switchgrass.     

Relationship between soil test phosphorus and phosphorus in runoff: effects of soil series variability

Phosphorus loss in runoff from agricultural fields has been identified as an important contributor to eutrophication. The objective of this research was to determine the relationship between phosphorus (P) in runoff from a benchmark soil (Cecil sandy loam; fine, kaolinitic, thermic Typic Kanhapludult) and Mehlich III-, deionized water-, and Fe(2)O(3)-extractable soil P, and degree of phosphorus saturation (DPS). Additionally, the value of including other soil properties in P loss prediction equations was evaluated. Simulated rainfall was applied (75 mm h(-1)) to 54 1-m(2) plots installed on six fields with different soil test phosphorus (STP) levels. Runoff was collected in its entirety for 30 min and analyzed for total P and dissolved reactive phosphorus (DRP). Soil samples were collected from 0- to 2-, 0- to 5-, and 0- to 10-cm depths. The strongest correlation for total P and DRP occurred with DPS (r(2) = 0.72). Normalizing DRP by runoff depth resulted in improved correlation with deionized water-extractable P for the 0- to 10-cm sampling depth (r(2) = 0.81). The STP levels were not different among sampling depths and analysis of the regression equations revealed that soil sampling depth had no effect on the relationship between STP and P in runoff. For all forms of P in runoff and STP measures, the relationship between STP and runoff P was much stronger when the data were split into groups based on the ratio of oxalate-extractable Fe to Al. For all forms of P in runoff and all STP methods, R(2) increased with the inclusion of oxalate-extractable Al and Fe in the regression equation. The results of this study indicate that inclusion of site-specific information about soil Al and Fe content can improve the relationship between STP and runoff P.     

In situ bioremediation through mulching of soil polluted by a copper-nickel smelter

Bioremediation of a heavy metal-polluted soil was investigated in a 3-yr field experiment by adding mulch to a polluted forest floor. The mulch consisted of a mixture of compost and woodchips. The remediation treatment decreased the toxicity of the soil solution to bacteria as determined by the [3H]-thymidine incorporation technique, that is, by measuring the growth rate of soil bacteria extracted from unpolluted humus after exposing them to soil solution containing heavy metals from the experimental plots. Canonical correlation analysis was performed in order to identify the chemical and microbiological changes in the soil. The pH of the mulched organic layer increased by one unit. The concentration of complexed Cu increased and that of free Cu2+ decreased in the soil solution from the mulch treatment. According to basal respiration and litter decomposition, microbial activity increased during the 3 yr following the remediation treatment. The [3H]-thymidine incorporation technique was also used to study the growth rate and tolerance of bacteria to Cu. The bacterial growth rate increased and the Cu tolerance decreased on the treated plots. The structure of the microbial community, as determined by phospholipid fatty acid (PLFA) analysis, remained unchanged. The results indicate that remediation of the polluted soil had occurred, and that adding a mulch to the forest floor is a suitable method for remediating heavy metal-polluted soil.     

Phosphorus runoff: effect of tillage and soil phosphorus levels

Continued inputs of fertilizer and manure in excess of crop requirements have led to a build-up of soil phosphorus (P) levels and increased P runoff from agricultural soils. The objectives of this study were to determine the effects of two tillage practices (no-till and chisel plow) and a range of soil P levels on the concentration and loads of dissolved reactive phosphorus (DRP), algal-available phosphorus (AAP), and total phosphorus (TP) losses in runoff, and to evaluate the P loss immediately following tillage in the fall, and after six months, in the spring. Rain simulations were conducted on a Typic Argiudoll under a corn (Zea mays L.)-soybean [Glycine max (L.) Merr.] rotation. Elapsed time after tillage (fall vs. spring) was not related to any form of P in runoff. No-till runoff averaged 0.40 mg L(-1) and 0.05 kg ha(-1) DRP and chisel-plow plots averaged 0.24 mg L(-1) and 0.02 kg ha(-1) DRP concentration and loads, respectively. The relationship between DRP and Bray P1 extraction values was approximated by a logistic function (S-shaped curve) for no-till plots and by a linear function for tilled plots. No significant differences were observed between tillage systems for TP and AAP in runoff. Bray P1 soil extraction values and sediment concentration in runoff were significantly related to the concentrations and amounts of AAP and TP in runoff. These results suggest that soil Bray P1 extraction values and runoff sediment concentration are two easily measured variables for adequate prediction of P runoff from agricultural fields.     

Removal of trichloroethylene from soil using the hydration of calcium oxide

Quicklime addition to soil at a remediation site was observed to sufficiently reduce TCE levels, but the cause of the removal could not be confirmed with the field data collected. Potential mechanisms for CaO treatment of trichloroethylene (TCE) in soil include degradation and volatilization. Since earlier studies found TCE degradation to occur during the hydration of CaO under conditions where volatilization was limited, research was conducted on mechanisms of TCE removal from soil by CaO application under conditions where volatilization was allowed to occur. TCE volatilization in soil treated with 0%, 5%, 10%, and 20% CaO doses was measured in experiments where the degree of volatilization could be tracked. The total TCE removal from soil spiked with TCE at CaO doses from 5% to 20% ranged from 97% to 99% of the initial TCE mass. Volatilization accounted for 64.4-92.5% of the TCE removal, with unrecovered TCE and TCE degradation accounting for the remaining fraction. The greater heat encountered with higher CaO doses helped minimize obstacles to TCE volatilization, such as high soil organic and clay content. Treatment with a 20% CaO dose, however, led to the formation of byproducts such as dichloroacetylene. TCE degradation to dichloroacetylene at the 20% CaO dose ranged from 2.7% to 6.4% of the initial TCE. Volatilization was concluded to be the dominant process for TCE removal from soil during CaO treatment.     

In situ speciation studies of copper-humic substances in a contaminated soil during electrokinetic remediation

Speciation of copper-humic substances (HS) in the electrokinetic remediation (EKR) of a contaminated soil was studied by in situ extended X-ray absorption fine structure (EXAFS) and X-ray absorption near edge structure (XANES) spectroscopies. The least-square fits of the XANES spectra suggested that the main Cu species in the contaminated soil were Cu-HS (50%), CuCO(3) (28%), Cu(2)O (11%), and CuO (11%). The Cu-HS in the contaminated soil possessed equatorial and axial Cu-O bond distances of 1.94 and 2.17 A with coordination numbers (CNs) of 3.6 and 1.4, respectively. In the EKR process, the axial Cu-O bond distance in the Cu-HS complexes was increased by 0.15 A, which might be due to a ligand exchange of the Cu-HS with H(2)O molecules in the electrolyte. After 180 min of EKR, about 50% of the Cu-HS complexes (or 24% of total Cu) in the soil were dissolved and formed [Cu(H(2)O)(6)](2+) in the electrolyte, 71% (or 17% of total Cu in the soil) of which were migrated to the cathode under the electric field (5 V/cm). This work exemplifies the use of in situ EXAFS and XANES spectroscopies for speciation studies of Cu chelated with HS in the contaminated soil during EKR.     

Enhanced transformation of lead speciation in rhizosphere soils using phosphorus amendments and phytostabilization: an x-ray absorption fine structure spectroscopy investigation

To formulate successful phytostabilization strategies in a shooting range soil, understanding how heavy metals are immobilized at the molecular level in the rhizosphere soil is critical. Lead (Pb) speciation and solubility in rhizosphere soils of five different plant species were investigated using extended X-ray absorption fine structure (EXAFS) spectroscopy and chemical extraction. The EXAFS analysis indicated that Pb occurred as PbCO (37%), Pb sorbed to organic matter (Pb-org: 15%), and Pb sorbed to pedogenic birnessite and/or ferrihydrite (Pb-ox: 36%) in the bulk soil. Comparison of the EXAFS spectra between bulk and rhizosphere soils demonstrated notable differences in fine structure, indicating that Pb species had been modified by rhizosphere processes. The estimated proportion of PbCO (25%) in the buckwheat soil was smaller than the other rhizosphere soils (35-39%). The addition of P significantly reduced Pb solubility in the bulk and rhizosphere soil except in the rhizosphere of buckwheat, for which the Pb solubility was 10-fold greater than in the other P-amended soils. This larger solubility in the buckwheat rhizosphere could not be explained by the total Pb speciation in the soil but was presumably related to the acidifying effect of buckwheat, resulting in a decrease of the soil pH by 0.4 units. The reduced Pb solubility by P amendment resulted from the transformation of preexisting PbCO (37%) into Pb(PO)Cl (26-32%) in the bulk and rhizosphere soils. In the P-amended rhizosphere soils, Pb-org species were no longer detected, and the Pb-ox pool increased (51-57%). The present study demonstrated that rhizosphere processes modify Pb solubility and speciation in P-amended soils and that some plant species, like buckwheat, may impair the efficiency of Pb immobilization by P amendments.     

Influence of plant growth on degradation of linear alkylbenzene sulfonate in sludge-amended soil

Widespread application of sewage sludge to agricultural soils in Denmark has led to concern about the possible accumulation and effects of linear alkylbenzene sulfonate (LAS) in the soil ecosystem. Therefore, we have studied the uptake and degradation of LAS in greenhouse pot experiments. Sewage sludge was incorporated into a sandy soil to give a range from very low to very high applications (0.4 to 90 Mg dry wt. ha(-1)). In addition, LAS was added as water solutions. The soil was transferred to pots and sown with barley (Hordeum vulgare L. cv. Apex), rape (Brassica napus L. cv. Hyola 401), or carrot (Daucus carota L.). Also, plant-free controls were established. For all additions there was no plant uptake above the detection limit at 0.5 mg LAS kg(-1) d.w, but plant growth stimulated the degradation. With a growth period of 30 d, LAS concentrations in soil from pots with rape had dropped from 27 to 1.4 mg kg(-1) dry wt., but in plant-free pots the concentration decreased only to 2.4 mg kg(-1) dry wt. When LAS was added as a spike, the final concentration in soil from planted pots was 0.7 mg kg(-1) dry wt., but in pots without plants the final concentration was much higher (2.5 mg kg(-1) dry wt.). During degradation, the relative fraction of homologues C10, C11, and C12 decreased, while C13 increased.     

Predicting runoff of suspended solids and particulate phosphorus for selected Louisiana soils using simple soil tests

This study was conducted to evaluate the relationships among total suspended solids (TSS) and particulate phosphorus (PP) in runoff and selected soil properties. Nine Louisiana soils were subjected to simulated rainfall events, and runoff collected and analyzed for various parameters. A highly significant relationship existed between runoff TSS and runoff turbidity. Both runoff TSS and turbidity were also significantly related to runoff PP, which on average accounted for more than 98% of total P (TP) in the runoff. Runoff TSS was closely and positively related to soil clay content in an exponential fashion (y=0.10e0.01x, R2=0.91, P<0.001) while it was inversely related to soil electrical conductivity (EC) (y=0.02 x(-3.95), R2=0.70, P<0.01). A newly-devised laboratory test, termed "soil suspension turbidity" (SST) which measures turbidity in a 1:200 soil/water suspension, exhibited highly significant linear relationships with runoff TSS (y=0.06x-4.38, R2=0.82, P<0.001) and PP (y=0.04x+2.68, R2=0.85, P<0.001). In addition, SST alone yielded similar R2 value to that of combining soil clay content and EC in a multiple regression, suggesting that SST was able to account for the integrated effect of clay content and electrolytic background on runoff TSS. The SST test could be used for assessment and management of sediment and particulate nutrient losses in surface runoff.     

Nitrogen- vs. phosphorus-based dairy manure applications to field crops: nitrate and phosphorus leaching and soil phosphorus accumulation

Management of animal manures to provide nutrients for crop growth has generally been based on crop N needs. However, because manures have a lower N/P ratio than most harvested crops, N-based manure management often oversupplies the crop-soil system with P, which can be lost into the environment and contribute to eutrophication of water bodies. We examined the effects of N- vs. P-based manure applications on N and P uptake by alfalfa (Medicago sativa L.), corn (Zea mays L.) for silage, and orchardgrass (Dactylis glomerata L.), leaching below the root zone, and accumulation of P in soil. Treatments included N- and P-based manure rates, with no nutrient input controls and inorganically fertilized plots for comparison. Nitrate concentrations in leachate from inorganic fertilizer or manure treatments averaged 14 mg NO(3)-N L(-1), and did not differ by nutrient treatment. Average annual total P losses in leachate did not exceed 1 kg ha(-1). In the top 5 cm of soil in plots receiving the N-based manure treatment, soil test P increased by 47%, from 85 to 125 mg kg(-1). Nitrogen- and P-based manure applications did not differ in ability to supply nutrients for crop growth, or in losses of nitrate and total P in leachate. However, the N-based manure led to significantly greater accumulation of soil test P in the surface 5 cm of soil. Surface soil P accumulation has implications for increased risk of off-field P movement.     

In situ measurement of soil moisture and pore-water pressures in an ‘incipient’ landslide: Lake Tutira,New Zealand

The immediate cost of shallow regolith landslides in New Zealand has been estimated to exceed US$33M annually. Since the majority of these landslides occur during prolonged wet conditions, or intense rainstorms, moisture conditions are a critical control. The nature, dynamics, and character of soil moisture conditions, and the piezometric response to rainfall, have been recorded within an ‘incipient’ landslide for more than 5 years. The study site, on pastoral hill country within the Lake Tutira catchment in northern Hawkes Bay, is typical of large areas of New Zealand episodically affected by extensive landsliding. Detailed continuous measurements show that both the soil moisture and piezometric response within the regolith are highly storm- and site-specific. The development of positive pore pressures is infrequent; they form only during intense rainstorms, and persist for a short time. The hydraulic response of the soil is primarily a function of storm characteristics, but this response can be modified by antecedent moisture conditions, topographic position, and heterogeneity of soil properties.     

Relationship of soil test phosphorus and sampling depth to runoff phosphorus in calcareous and noncalcareous soils

A study was initiated to investigate the relationship between soil test P and depth of soil sampling with runoff losses of dissolved molybdate reactive phosphorus (DMRP). Rainfall simulations were conducted on two noncalcareous soils, a Windthorst sandy loam (fine, mixed, thermic Udic Paleustalf) and a Blanket clay loam (fine, mixed, thermic Pachic Argiustoll), and two calcareous soils, a Purves clay (clayey, smectitic, thermic Lithic Calciustoll) and a Houston Black clay (fine, smectitic, thermic Udic Haplustert). Soil (0- to 2.5-, 0- to 5-, and 0- to 15-cm depths) and runoff samples were collected from each of the four soils in permanent pasture exhibiting a wide range in soil test P levels (as determined by Mehlich III and distilled water extraction) due to prior manure applications. Simulated rain was used to produce runoff, which was collected for 30 min. Good regression equations were derived relating soil test P level to runoff DMRP for all four soil types, as indicated by relatively high r2 values (0.715 to 0.961, 0- to 5-cm depth). Differences were observed for the depth of sampling, with the most consistent results observed with the 0- to 5-cm sampling depth. Runoff DMRP losses as a function of the concentration of P in soil were lower in calcareous soils (maximum of 0.74 mg L(-1)) compared with noncalcareous soils (maximum of 1.73 mg L(-1)). The results indicate that a soil test for environmental P could be developed, but it would require establishing different soil test P level criteria for different soils or classes of soils.     

Removal of o-nitrophenol from water by electrochemical degradation using a lead oxide/titanium modified electrode

This study examined o-nitrophenol removal from aqueous solutions by electrochemical oxidation employing a modified electrode. The modified electrode was produced by electrodepositing lead oxide onto a titanium substrate. Following electrochemical oxidation of o-nitrophenol-containing solutions, the remaining o-nitrophenol concentration and chemical oxygen demand (COD) values were determined. The optimum parameters were current density of 40 mA cm(-2), pH of 2.47, 60 min of electrolysis time, 4 g L(-1) NaCl electrolyte solution and temperature of 30 degrees C. Under these optimum conditions of electrochemical degradation using a lead oxide/titanium modified electrode complete removal of o-nitrophenol and COD was achieved.     

Non-ferrous metals and economic growth: The future demand for lead

As national economies grow, requirements for physical resources increase. This paper attempts to forecast future world demand for lead, by deriving a relationship between the amount consumed per capita and the level of economic development, and then using this to generate world demand figures based on some predictions of future economic growth. Although the rate of increase in demand for lead may decline as high levels of GDP are reached, it is nevertheless predicted that world annual demand could continue rising exponentially over the next 50 or 60 years, in the absence of constraints due to lack of physical resources or very high differential prices. This is essentially because large areas of the world will still be increasing their GDP per capita over the range where the rate of increase in demand for lead is increasing steeply.     

Sorption dynamics of organic and inorganic phosphorus compounds in soil

Phosphorus retention in soils is influenced by the form of P added. The potential impact of one P compound on the sorption of other P compounds in soils has not been widely reported. Sorption isotherms were utilized to quantify P retention by benchmark soils from Indiana, Missouri, and North Carolina when P was added as inorganic P (Pi) or organic P (beta-D-glucose-6-phosphate, G6P; adenosine 5'-triphosphate, ATP; and myoinositol hexaphosphate, IP6) and to determine whether soil P sorption by these organic P compounds and Pi was competitive. Isotherm supernatants were analyzed for pH and total P using standard protocols, while Pi and organic P compounds were assayed using ion chromatography. Under the controlled conditions of this study, the affinity of all soils for P sources followed the order IP6 > G6P > ATP > Pi. Each organic P source had a different potential to desorb Pi from soils, and the order of greatest to least Pi desorption was G6P > ATP > IP6. Glucose-6-phosphate and ATP competed more directly with Pi for sorption sites than IP6 at greater rates of P addition, but at the lesser rates of P addition, IP6 actually desorbed more Pi. Inositol hexaphosphate was strongly sorbed by all three soils and was relatively unaffected by the presence of other P sources. Decreased total P sorption due to desorption of Pi can be caused by relatively small additions of organic P, which may help explain vertical P movement in manured soils. Sorption isotherms performed using Pi alone did not accurately predict total P sorption in soils.