上转换发光剂掺杂纳米TiO2的制备及可见光降解乙基紫的研究

合成了一种新型含有稀土金属Er的上转换发光剂40CdF₂·60BaF₂·1.6Er₂O₃,此上转换发光剂在488 nm可见光的激发下,产生了5个波长均小于387 nm的上转换紫外光发射峰.采用超声波分散的方法制备出了上转换发光剂掺杂的纳米TiO₂可见光光催化剂.利用X-射线衍射(XRD)及透射电镜(TEM)对催化剂进行了表征.以乙基紫染料为研究对象,研究了在(三基色灯下发出的)可见光的照射下该可见光光催化剂的催化降解性能,并与未掺杂的纳米TiO₂粉末的催化性能进行了对比.结果表明,作为掺杂成分的上转换发光剂可有效地将可见光转化为紫外光并被纳米TiO₂粉末吸收利用,在可见光照射12.0 h后乙基紫降解率达到了99.68%,大大高于未掺杂纳米TiO2时的降解率.     

TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应

以内分泌干扰物阿特拉津为模型污染物,研究了TiO2-Fe3+可见光催化H2O2降解阿特拉津的协同效应.结果表明,在H2O2存在条件下,金红石TiO2经可见光激发可持续稳定地产生.OH自由基,在Fe3+协同作用下,.OH自由基生成量急剧增加;TiO2能可见光催化H2O2降解阿特拉津,金红石TiO2显示出较锐钛矿TiO2及混晶TiO2(TiO2P25)更高的催化活性,反应60 min,阿特拉津的降解率可达40%;以Fe3+协同TiO2可见光催化H2O2降解阿特拉津时,反应效率显著加快,反应5 min即对阿特拉津的降解率达到100%,而金红石TiO2显示出更为明显的协同效应.     

Fe2O3/TiO2负载膨胀珍珠岩光催化降解罗丹明B

为获得高效催化活性的光催化材料,研究不同煅烧氛围对材料在可见光下催化性能的影响,以膨胀珍珠岩（EP）为载体,采用溶胶-凝胶法,在不同煅烧氛围（O₂和/或NH₃）下制备Fe₂O₃/TiO₂负载EP的光催化复合材料〔Fe₂O₃-TEP（O₂）、Fe₂O₃-TEP（NH₃）、Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）〕,采用EDS（X-射线色散能谱）、BET（比表面积及孔径分析）、XRD（X射线衍射）、SEM（扫描电子显微镜）、XPS（X射线光电子能谱）等对复合材料进行表征,并研究了其在可见光下对罗丹明B的光催化降解效果.结果表明:①复合材料成功负载了Ti、Fe元素,负载的TiO₂以锐钛矿型存在,Fe₂O₃的掺杂增强了TiO₂对可见光的响应能力;②不同的煅烧氛围明显影响复合材料的晶粒尺寸、比表面积和光催化性能,其中,Fe₂O₃-TEP（O₂,NH₃）的光催化性能最好,4 h后罗丹明B降解率达到87.59%,Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）4 h后对罗丹明B的降解率则分别为65.02%、62.48%和47.48%;③在试验条件下,复合材料的光催化反应符合一阶反应动力学方程,Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）相应的降解速率常数分别为0.008 3、0.004 3、0.004 3和0.002 7 min-1.研究显示,通过溶胶-凝胶法所制备的复合材料（Fe₂O₃-TEP）经煅烧后所得矿相均一;Fe₂O₃掺杂TiO₂可形成Ti—O—Fe键,减小TiO₂固有的禁带宽度;复合材料光催化性能也受到煅烧氛围的影响,先O₂后NH₃煅烧条件下所得材料的光催化性能最佳.      

UV/TiO2/H2O2体系对制药废水二级出水的处理特性研究

以某制药企业的二级出水为研究对象,对比了UV/TiO₂、UV/H₂O₂、UV/TiO₂/H₂O₂ 3种高级氧化工艺的处理效果,利用自主设计的一体化光催化装置进行了连续动态试验,并通过凝胶渗透色谱（GPC）、傅里叶变换红外光谱（FT-IR）、三维荧光光谱（EEM）、斑马鱼急性毒性试验等方法研究了处理前后有机物特性和生物毒性的变化.结果表明,与UV/TiO₂和UV/H₂O₂体系相比,UV/TiO₂/H₂O₂光芬顿体系对有机物的去除效果更好,当TiO₂投加量为1 g·L^-1,H₂O₂投加量为100 mg·L^-1时,处理效果达到最佳.一体化光催化装置能够利用UV/TiO₂/H₂O₂光芬顿技术快速高效地降解二级出水中的有机污染物,反应30 min时COD去除率达到50%以上.经UV/TiO₂/H₂O₂深度处理后,废水中的大分子有机物分解转换为小分子,有机物中的不饱和结构明显减少,腐殖质等溶解性有机物基本降解完全.毒性试验结果表明,该二级出水的生物毒性经深度处理后显著降低,对斑马鱼胚胎不存在致畸致死效应.     

UV/H2O2降解羟苯甲酮反应动力学及影响因素

有机防晒剂随着日常使用不断进入环境中,成为一类新兴污染物.考察了UV/H2O2工艺对典型有机防晒剂羟苯甲酮(BP-3)的水相光化学降解特征,并对BP-3降解反应的影响因素包括初始BP-3浓度、H2O2浓度、UV光强、共存阳离子和阴离子、叔丁醇和腐殖酸投加量等进行了研究.结果表明,BP-3的降解速率常数随初始BP-3浓度升高而降低,随着H2O2浓度增大而增高,随着UV光强增强而增大;阴离子会在一定程度上降低反应速率,阳离子中Fe3+会产生类芬顿反应,促进生成·OH,对降解反应有显著的促进作用,投加叔丁醇和腐殖酸皆会抑制降解反应进行.采用每一对数减小级电能输入(EEo)指标对UV/H2O2工艺的电能利用效率进行了评价,Fe3+的加入显著减小了EEo.研究不同因素对UV/H2O2工艺降解效果的影响,可对实际工程中采用UV/H2O2去除苯甲酮类有机防晒剂提供参考.     

TiO2-石墨烯（Gn）复合材料光催化降解O3研究

通过改性Hummer法及溶胶凝胶法,制备出TiO2-石墨烯光催化复合材料.经吸附-光催化活性实验选出光催化活性最高的含C量为1.5%(质量分数)的TiO2-石墨烯复合材料,并在自行设计的模拟大型客机环境的气相光催化反应器中,进行O3光催化降解实验研究.结果表明,TiO2-石墨烯复合光催化材料在较短时间内对O3有较高的降解效率,且其光催化活性显著优于纯TiO2材料.初始O3浓度为(0.150～0.200)×10-6时,复合光催化剂受紫外光激发60 min的光催化降解率为66.12%,初始O3浓度为(0.950～1.000)×10-6时,其光催化降解率约为77%,较低浓度时((0.100～0.150)×10-6),O3去除率也能达到45.45%.此外,通过探讨光催化材料的重复使用性能,表明复合光催化剂重复使用4次以内,其对O3的光催化降解率保持基本稳定.     

TiO2光催化联合技术降解苯酚机制及动力学

主要研究了TiO2光催化体系结合H2O2或外加电催化(EC)体系对苯酚催化降解效率的影响,评价比较TiO2/UV、H2O2/UV、TiO2/UV/H2O2、TiO2/UV/EC体系下苯酚降解机制及动力学.结果表明,TiO2/UV/H2O2和TiO2/UV/EC体系下苯酚降解效率明显高于TiO2/UV体系,当苯酚溶液pH值为6,TiO2质量浓度0.2 g·L-1,紫外光照2 h,光催化降解效果达到86%,当电流密度为12 mA·cm-2,则苯酚可达到100%去除.比较了不同催化体系下的能量利用率,苯酚降解15 min,TiO2/UV/EC体系能量利用率最大为0.030 6 g·(kW·h)-1,其能量消耗为0.0640 kW·h-1,说明采用TiO2/UV/EC体系能更多地利用能量降解苯酚.通过不同催化体系下中间产物分析,建立苯酚及其中间产物对苯二酚、邻苯二酚和苯醌的拟一级降解动力学模型,通过模型验证各催化体系下苯酚的降解历程,同时也说明了TiO2/UV/EC体系有利于苯酚及其中间产物的降解.     

Characterizing the optimal operation of photocatalytic degradation of BDE-209 by nano-sized TiO2

Brominated flame retardants have been widely used in industry. There is a rapid growing public concern for their availabilities in the environment. Advanced oxidation process (AOP) is a promising and efficient technology which may be used to remove emerging chemicals such as brominated flame retardants. This project aims at investigating optimal operational conditions for the removal of BDE-209 using nano-scaled titanium(IV) oxide. The residual PBDE congeners after photocatalytical degradation of BDE-209 by TiO₂ were analysed by gas chromatography-mass spectrometry (GC-MS). It was found that the degradability of BDE-209 by TiO₂ was attributed to its photocatalytic activity but not the small size of the particles. The half-life of removing BDE-209 by TiO₂ was 3.05 days under visible light. Tetra- and penta-BDEs were the major degraded products of BDE-209. Optimum conditions for photocatalytical degradation of BDE-209 was found to be at pH 12 (93% ± 1%), 5, 10, 20 mg/L (93.0% ± 1.70%, 91.6% ± 3.21%, 91.9% ± 0.952%, respectively), respectively of humic acid and in the form of anatase/rutile TiO₂ (82% ± 3%). Hence, the efficiency of removing BDE-209 can be maximized while being cost effective at the said operating conditions.     

Photocatalytic degradation of organochlorine compounds using TiO2 supported on fiberglass cloth

The feasibility of photocatalytic degradation of organochlorine compounds using TiO₂ supported on fiberglass cloth as a photocatalyst was studied. The results showed that 2.0×10^-4 mol/dm³ of dichloroethylene, trichloroethylene and tetrachloroethylene can be completely photocatalytically degraded within a short time under illumination with a 375W medium pressure mercury lamp. The effects of parameters such as illumination time, initial concentration of organochlorine compounds, amount of air flow and concentration of H₂O₂ on the photocatalytic degradation were investigated. The TiO₂ supported on the fiberglass was not easily detached and after 500h illumination there was no significant loss of photocatalytic activity of TiO₂. The passible mechanisms of photocatalytic degradation were discussed.     

氧化剂增强TiO2纤维光催化降解DMF研究

研究TiO₂纤维光催化降解DMF水溶液的结果表明:氧化剂增强了TiO₂纤维对DMF的降解能力,在其它反应条件相同情况下,O₃/TiO₂(F)对DMF降解率是air/TiO₂(F)和H₂O₂/TiO₂(F)的1.5倍左右,且降解速率提高2倍左右,COD分析表明DMF几乎完全矿化.同时实验过程中确定了DMF光催化降解中间产物仲胺的存在.以二甲胺为仲胺代表物进行光催化降解研究表明,中间产物仲胺的迅速降解是O₃增强TiO₂纤维降解效应的主要因素.     

Tricrystalline TiO2 with enhanced photocatalytic activity and durability for removing volatile organic compounds from indoor air

It is important to develop efficient and economic techniques for removing volatile organic compounds(VOCs) in indoor air. Heterogeneous Ti O_2-based semiconductors are a promising technology for achieving this goal. Anatase/brookite/rutile tricrystalline Ti O_2 with mesoporous structure was synthesized by a low-temperature hydrothermal route in the presence of HNO_3.The obtained samples were characterized by X-ray diffraction and N_2 adsorption–desorption isotherm. The photocatalytic activity was evaluated by photocatalytic decomposition of toluene in air under UV light illumination. The results show that tricrystalline Ti O_2 exhibited higher photocatalytic activity and durability toward gaseous toluene than bicrystalline Ti O_2,due to the synergistic effects of high surface area, uniform mesoporous structure and junctions among mixed phases. The tricrystalline Ti O_2 prepared at R HNO_3= 0.8, containing80.7% anatase, 15.6% brookite and 3.7% rutile, exhibited the highest photocatalytic activity,about 3.85-fold higher than that of P25. The high activity did not significantly degrade even after five reuse cycles. In conclusion, it is expected that our study regarding gas-phase degradation of toluene over tricrystalline Ti O_2 will enrich the chemistry of the Ti O_2-based materials as photocatalysts for environmental remediation and stimulate further research interest on this intriguing topic.     

Tricrystalline TiO2 with enhanced photocatalytic activity and durability for removing volatile organic compounds from indoor air

It is important to develop efficient and economic techniques for removing volatile organic compounds (VOCs) in indoor air. Heterogeneous TiO₂-based semiconductors are a promising technology for achieving this goal. Anatase/brookite/rutile tricrystalline TiO₂ with mesoporous structure was synthesized by a low-temperature hydrothermal route in the presence of HNO₃. The obtained samples were characterized by X-ray diffraction and N₂ adsorption–desorption isotherm. The photocatalytic activity was evaluated by photocatalytic decomposition of toluene in air under UV light illumination. The results show that tricrystalline TiO₂ exhibited higher photocatalytic activity and durability toward gaseous toluene than bicrystalline TiO₂, due to the synergistic effects of high surface area, uniform mesoporous structure and junctions among mixed phases. The tricrystalline TiO₂ prepared at R_HNO3 = 0.8, containing 80.7% anatase, 15.6% brookite and 3.7% rutile, exhibited the highest photocatalytic activity, about 3.85-fold higher than that of P25. The high activity did not significantly degrade even after five reuse cycles. In conclusion, it is expected that our study regarding gas-phase degradation of toluene over tricrystalline TiO₂ will enrich the chemistry of the TiO₂-based materials as photocatalysts for environmental remediation and stimulate further research interest on this intriguing topic.     

Investigation of the effects of humic acid and H2O2 on the photocatalytic degradation of atrazine assisted by microwave

A solution of atrazine in a TiO₂ suspension, an endocrine disruptor in natural water, was tentatively treated by microwave-assisted photocatalytic technique. The effects of mannitol, oxygen, humic acid, and hydrogen dioxide on the photodegradation rate were explored. The results could be deduced as follows: the photocatalytic degradation of atrazine fits the pseudo-first-order kinetic well with k = 0.0328 s⁻¹, and ·OH was identified as the dominant reactant. Photodegradation of atrazine was hindered in the presence of humic acid, and the retardation effect increased as the concentration of humic acid increased. H₂O₂ displayed a significant negative influence on atrazine photocatalysis efficiency. Based on intermediates identified with gas chromatography-mass spectrometry (GC-MS) and Liquid chromatography-mass spectrometry (LC-MS/MS) techniques, the main degradation routes of atrazine are proposed.     

Fabrication of Bi2O3/TiO2 nanocomposites and their applications to the degradation of pollutants in air and water under visible-light

A nanoheterojunction composite photocatalyst Bi2O3/TiO2working under visible-light(λ 420 nm) was prepared by combining two semiconductors Bi2O3 and TiO2 varying the Bi2O3/TiO2molar ratio. Maleic acid was employed as an organic binder to unite Bi2O3 and TiO2 nanoparticles. The SEM, TEM, XRD and diffuse reflectance spectra were utilized to characterize the prepared Bi2O3/TiO2nanoheterojunction. The nanocomposite exhibited unusual high photocatalytic activity in decomposing 2-propanol in gas phase and phenol in aqueous phase and, evolution of CO2 under visible light irradiation while the end members exhibited low photocatalytic activity. The composite was optimized to 5 mol% Bi2O3/TiO2. The remarkable high photocatalytic efficiency originates from the unique relative energy band position of Bi2O3 and TiO2 as well as the absorption of visible light by Bi2O3.     

Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

Acid-assisted hydrothermal synthesis of nanocrystalline TiO2 from titanate nanotubes: Influence of acids on the photodegradation of gaseous toluene

In order to efficiently remove volatile organic compounds (VOCs) from indoor air, onedimensional titanate nanotubes (TiNTs) were hydrothermally treated to prepare TiO₂ nanocrystals with different crystalline phases, shapes and sizes. The influences of various acids such as CH₃COOH, HNO₃, HCl, HF and H₂SO₄ used in the treatment were separately compared to optimize the performance of the TiO₂ nanocrystals. Comparedwith the strong and corrosive inorganic acids, CH₃COOH was not only safer andmore environmentally friendly, but also more efficient in promoting the photocatalytic activity of the obtained TiO₂. Itwasobserved that the anatase TiO₂ synthesized in 15 mol/L CH₃COOH solution exhibited the highest photodegradation rate of gaseous toluene (94%), exceeding that of P25 (44%) by a factor ofmore than two. The improved photocatalytic activity was attributed to the small crystallite size and surface modification by CH₃COOH. The influence of relative humidity (20%-80%) on the performance of TiO₂ nanocrystals was also studied. The anatase TiO₂ synthesized in 15 mol/L CH₃COOH solution was more tolerant tomoisture than the other TiO₂ nanocrystals and P25.     

BiOCl/TiO2的氯化改性及其新式光生自由基催化反应

采用溶胶凝胶法制备了BiOCl/TiO₂复合催化剂,透射电镜（TEM）照片显示,两种半导体分布均匀、相互连接,形成的异质结可以为电子传导提供有效通道.经过氯化处理的复合材料具备更强的光催化能力,在紫外光条件下对苯的降解率达到90%,是原BiOCl/TiO₂的2倍、纯TiO₂的10倍.本文利用X射线光电子能谱、红外光谱和电子顺磁共振,对表面氯化的机理进行研究.结果表明,氯元素以Ti—Cl的方式吸附在催化剂表面,在光照条件下光生空穴夺取一个电子,使其生成氯自由基,进而配合超氧、羟基,构成一种新型的三自由基光催化体系,使催化降解能力大幅提升.最后,利用实验方法得到了光生氯自由基的直接证据,并构建了该体系的光催化反应机理.     

WC/TiO2纳米复合界面光催化剂制备及其光催化降解酚类污染物研究

设计并制备了新型WC/TiO2纳米复合界面光催化剂应用于酚类污染物的光催化降解反应中.采用X射线衍射(XRD)和扫描电子显微镜(SEM)技术分析了WC/TiO2纳米复合界面光催化剂的晶型和表面形貌.结果显示锐钛矿型TiO2纳米颗粒均匀地分散在WC纳米球表面并很好地构筑了WC/TiO2界面.研究了不同WC负载比例的WC/TiO2光催化剂在模拟太阳光照射下降解苯酚的光催化性能.结果表明:WC/TiO2复合界面的形成可以有效地提高TiO2光催化降解性能;其中,3%WC/TiO2(质量分数)光催化降解苯酚的活性最高.利用紫外-可见光谱(UV-Vis)和高效液相色谱-质谱联用技术(HPLC-MS)分析了WC/TiO2纳米复合界面光催化剂降解苯酚的中间产物,提出了苯酚在WC/TiO2界面上可能的降解机理.     

Immobilization of self-assembled pre-dispersed nano-TiO2 onto montmorillonite and its photocatalytic activity

The immobilization of pre-dispersed Ti O_2 colloids onto the external surface of the clay mineral montmorillonite(Mt) was accomplished and regulated via a self-assembly method employing the cationic surfactant cetyltrimethylammonium bromide(CTAB). The role of CTAB in the synthesis process was investigated by preparing a series of Ti O_2-CTAB-Mt composites(TCM) with various CTAB doses. The results indicated that a uniform and continuous Ti O_2 film was deposited on the external surface of montmorillonite in the composite synthesized with 0.1 wt.% of CTAB, and the TCM nano-composites showed much higher values for specific surface area, average pore size and pore volume than the raw montmorillonite clay. Then, the formed TCM materials were applied in photocatalytic degradation of 2,4-dichlorophenol(2,4-DCP) in aqueous solution. The degradation efficiency reached as high as 94.7%. Based on the degradation intermediates benezoquinone, fumaric acid and oxalic acid identified by LC–MS analysis, a mechanism for the photocatalytic oxidation of 2,4-DCP on Ti O_2/Mt nano-composites is proposed.     

In_2TiO_5纳米带的静电纺丝法制备及光催化性能

以酞酸丁酯(Ti(OC_4H_9)_4)、硝酸铟(In(NO3)3)和聚乙烯吡咯烷酮(PVP-K30)为原料,采用静电纺丝技术制备了In_2TiO_5纳米带.利用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见漫反射光谱(UV-vis DRS)和氮气吸附-脱附等温线(BET)等技术对样品进行了表征.考察了In_2TiO_5纳米带在光催化降解罗丹明B(RhB)、甲基橙(MO)、亚甲基蓝(MB)和左氧氟沙星(LEV)过程中的应用性能,研究了不同离子型物质、溶液的pH和MB起始浓度对In_2TiO_5纳米带光催化活性的影响.结果表明:In_2TiO_5纳米带具有正交晶系结构,禁带宽度为3.47 eV,比表面积为20.71 m~2·g~(-1),可应用于4种不同离子型物质的光催化降解,发现光催化效果与被降解物质的表面带电性质有关.在紫外光照射下,90 min,对MB的降解率达98.1%,其降解过程服从一级动力学模型.