Sources of potentially toxic elements and organic pollutants in an urban area subjected to an industrial impact

Urban and industrial development has caused a major impact on environmental soil quality. This work assesses the extent and severity of contamination in a small urban area subjected to an industrial impact and identifies the major anthropogenic inputs. Twenty-six soil samples were collected from agricultural and urban sites, and concentrations of potentially toxic elements (As, Cd, Cu, Cr, Fe, Mn, Ni, Pb and Zn), PAHs and PCBs, were determined. In spite of the low median concentrations observed, some sites represent a potential hazard for human health and ecosystems. Concentrations of contaminants were higher than those found in a nearby city, indicating that the study area is affected by the surrounding industry. The use of multivariate statistical analyses allowed for the identification of the main factors controlling the variability of potentially toxic elements and organic pollutants in the soils. The presence of Cr, Fe, Mn and Ni was associated with geogenic inputs, and Cu, Pb, Zn, As, PAHs and PCBs were associated with anthropogenic inputs. Industry and traffic were the most important anthropogenic sources. Soil characteristics were identified as important factors controlling the spatial variability of elements, both from recognised natural and anthropogenic origin. Differences between land uses were observed, which may be attributed to both management practices and proximity to sources.     

Air pollution impact assessment on agroecosystem and human health characterisation in the area surrounding the industrial settlement of Milazzo (Italy): a multidisciplinary approach

In order to evaluate the impact of atmospheric pollutants emitted by the industrial settlement of Milazzo (Italy) on agriculture, sulphur dioxide and ozone levels in air were monitored and the data were used to estimate yield losses of the most widespread cultures. Trace element concentrations in crops and soils were also detected and metabolic profiles of soil microbial communities were considered. Vibrio fischeri test was used to appraise airborne pollutant ecotoxicity and epidemiological studies on causes of death distribution were carried out to characterize health state of people living in the area. All the sampling points were selected in farms on the basis of a theoretical meteo-diffusive model of industrial air pollutants. Experimental SO₂ and O₃ values mainly exceeded the threshold established by Italian and EU regulations to protect vegetation and they correspond to estimated significant crop losses. Conversely toxic element residues in soils and in agroalimentary products were generally lower than the fixed values. SO₂ and O₃ concentrations, toxic element contents and ecotoxicity levels of airborne pollutants were not related only to industrial site emissions, while the fluctuations on metabolic profiles of soil microbial communities seem to agree with the predicted deposition of xenobiotic compounds from the industrial plants. The epidemiological study evidenced a better health state of populations living in the investigated area than in the Messina province and the Sicily region but, inside the area, males living in the municipalities closest to the industrial settlement exhibited a worst health state than those in the very far ones.     

Air monitoring of persistent organic pollutants in the Great Lakes: IADN vs. AEOLOS

When designing a monitoring campaign, one has to consider many factors in the decision to perform a long-term synoptic monitoring program or a short-term intensive study. Each has its own advantages and disadvantages. This paper compares and contrasts the information obtained from two studies conducted on the Laurentian Great Lakes. One, the Integrated Atmospheric Deposition Network (IADN), is a long-term synoptic monitoring study and the other, the Atmospheric Exchange Over Lakes and Oceans (AEOLOS), was a short-term intensive study. The advantages of long-term synoptic monitoring programs are providing greater spatial information, the relative influence of long and short-range transport on the regional background, gross loadings representative of the majority of each lake and long-term temporal trends. Short-term intensive studies provide more information on the processes governing sources, transport and deposition, such as the urban/industrial influence on adjacent large water bodies, specific sources to an urban/industrial area and short-term fluctuations in concentrations due to meteorology, source strength and photochemical reactions. Using information provided by both the IADN and AEOLOS studies, areas of urban influence are predicted for each of the five Great Lakes.     

珠江三角洲某乡镇气溶胶中有机污染物的研究

通过对珠江三角洲某一乡镇的城区及三个乡村气溶胶有机污染物研究 ,发现烷烃类有机物高分子部分具有明显分不开的鼓包 ,污染较为显著 ;所有样品均含有多种多环芳烃 (PAHs) ,化合物种类比广州多 4～ 8种 ,并均含有机动车尾气排放的标志化合物烷基苯 (M Z91 ,92 )和塑料增塑剂等来源的邻苯二甲酸酯类 (M Z1 49)。表明该镇各区域均已明显受到机动车尾气排放和企业废气排放的污染。     

Simulating the production and dispersion of environmental pollutants in aerosol phase in an urban area of great historical and cultural value

Mathematical models were developed to simulate the production and dispersion of aerosol phase atmospheric pollutants which are the main cause of the deterioration of monuments of great historical and cultural value. This work focuses on Particulate Matter (PM) considered the primary cause of monument darkening. Road traffic is the greatest contributor to PM in urban areas. Specific emission and dispersion models were used to study typical urban configurations. The area selected for this study was the city of Florence, a suitable test bench considering the magnitude of architectural heritage together with the remarkable effect of the PM pollution from road traffic. The COPERT model, to calculate emissions, and the street canyon model coupled with the CALINE model, to simulate pollutant dispersion, were used. The PM concentrations estimated by the models were compared to actual PM concentration measurements, as well as related to the trend of some meteorological variables. The results obtained may be defined as very encouraging even the models correlated poorly: the estimated concentration trends as daily averages moderately reproduce the same trends of the measured values.     

Lichen biomonitoring of trace metals in the Pistoia area (central northern Italy)

The epiphytic lichen Parmelia caperata (L.) Ach. was used as bioaccumulator of the heavy metals Cd, Cr, Cu, Hg, Ni, Pb and Zn in the environs of the town of Pistoia (central northern Italy). The concentrations of Cd, Cr, Ni, Hg and Pb were comparable with those found in areas not subject to atmospheric pollution. Copper and especially Zn were found in rather high concentrations. Fertilizers and pesticides were the main source of atmospheric contamination.     

Hydrogeochemical characterization of contaminated groundwater in Patancheru industrial area,southern India

The groundwater is one of the most contaminated natural resources in Patancheru industrial area due to unplanned and haphazard industrial growth and urbanization without following basic pollution control norms. The rapid industrialization initiated in early 1970 has started showing up its after effects few years later in the form of physiochemical contamination of the both surface and groundwater bodies of the area. It has resulted in local people being deprived of safe drinking water, plant and aquatic life has severely affected, and situation is deteriorating over the years in the area in spite of some preventive and remedial measures being initiated. The focus of the present study is to understand the chemical characteristics of groundwater and geochemical processes the contaminant water is undergoing which are normally imprinted in its ionic assemblages. The water samples collected in pre- and post-monsoon seasons from forty two groundwater and four surface water sources were analyzed for major constituents such as Ca²⁺, Mg²⁺, Na⁺, K⁺, CO₃⁻, HCO₃⁻, Cl⁻, SO₄²⁻, NO₃⁻, and F⁻, and selected samples were tested for ten important trace metals like Fe, Pb, Bi, Mn, Cr, Co, Ni, Cu, Zn, and Cd. Na⁺ among cations and Cl⁻ among anions dominate the water in both the seasons where as Ca²⁺, HCO₃⁻, and Cl⁻ show significant reduction in their ionic strength in post-monsoon. The groundwater in general is of mixed type, but most of it belong to Na⁺–Cl⁻, Na⁺–HCO₃⁻, Ca²⁺–Mg²⁺–HCO₃⁻, and Ca²⁺–Mg²⁺–Cl⁻ facies. The Na⁺ and Ca²⁺ are in the transitional state with Na⁺ replacing Ca²⁺ and HCO₃⁻–Cl⁻ due to physiochemical changes in the aquifer system. The evaluation of hydrochemistry through various ionic indices, ratios, and plots suggest that silicate–carbonate weathering, ion exchange, dissolution, and evaporation processes are responsible for origin of the present chemical status of the groundwater which is also controlled by the contamination from extraneous sources that could have accelerated the dissolution processes. Gibbs plots authenticate that the evolution of water chemistry is influenced by interaction of percolating water with aquifer matrix apart from anthropogenic enrichment of elements which get over concentrated due to evaporation.     

Deposition fluxes of PCDD/Fs in the area surrounding a steel plant in northwest Italy

The paper aims at investigating the contribution of a steel plant located in a rural area in northwestern Italy (700,000 tons of steel/year) to the deposition fluxes of Polychorinated Dibenzo-p-dioxins and Polychorinated dibenzofurans (PCDD/PCDFs) at local level through the analysis of sampling data, literature data, and air dispersion model (AERMOD)output data. Total measured deposition fluxes of PCDD/PCDFs in three monitoring stations were consistent with other studies carried out in Italy in urban and suburban areas and in rural European areas; while these were lower than those measured in other European urban/suburban areas or in sites influenced by industrial sources. Furthermore, the measured fluxes were also compared with the pattern of PCDD/Fs in ambient air sampled at the same sites in a previous study. This comparison showed a similarity between air concentration and deposition patterns of the samples collected at the three monitoring stations and a clear distinction of these from the source. The study was completed with AERMOD simulations, conducted with a mass mean particle diameter of 0.5 μm, according to the particle size distribution of the samples collected at the source. AERMOD calculated deposition fluxes of two to three orders of magnitude lower than those measured in two monitoring points; while in the most distant monitoring station, the deposition fluxes were too low to be calculated by the model. The simulations confirmed that the most distant monitoring station was not subject to emissions from the steel plant. The analysis highlighted the limited influence of the source in the local PCDD/F deposition fluxes.     

焦化、染料废水和洹河水体的有机污染研究

采用GC/MS联用仪对焦化、染料废水和地表水中有机物进行定性、定量分析,探讨了污染源与受纳区的地表水中有机物种类和含量间的关系。     

Temporal trends of element concentrations and ecophysiological parameters in the lichen Pseudevernia furfuracea transplanted in and around an industrial area of S Italy

This study investigated the temporal trends of element concentrations and ecophysiological parameters (integrity of cell membranes, membrane lipid peroxidation, and sample vitality) in thalli of the lichen Pseudevernia furfuracea transplanted in and around an industrial area of S Italy from May 2010 to May 2011, once every 3 months. Element accumulation at levels indicating that the atmosphere of the study area was polluted by most elements occurred only during the third trimester of exposure, and the ecophysiological parameter best reflecting this trend was sample vitality expressed in terms of activity of the enzyme dehydrogenase. Among the available climatological parameters, the different amount of rainfall during the exposure period may influence the results, especially the number of hours with rainfall >16 mm/day, which is the threshold between light–moderate and moderate–heavy rainfall in the Mediterranean area.     

Chemical composition of individual aerosol particles from working areas in a nickel refinery

Individual aerosol particles (n = 1170) collected at work stations in a nickel refinery were analyzed by wavelength-dispersive electron-probe microanalysis. By placing arbitrary restrictions on the contents of sulfur and silicon, the particles could be divided into four main groups. Scanning electron images indicated that most of the particles examined were relatively small (< or = 2 microm, equivalent projected area diameter), and that their morphology suggested formation from a melt. There was an absence of well-defined phases and simple stoichiometries, indicating that exposures to pure substances such as nickel subsulfide or specific oxides appeared not to occur. Although the elemental composition of particles varied greatly, a rough association was evident with the known elemental content of the refinery intermediates. The implications of the findings for aerosol speciation measurements, toxicological studies and interpretation of adverse health effects are explored.     

用GC／MS联用分析焦化厂蒸氨废水中的有机物组成

本文对焦化厂蒸氨废水进行了ＧＣ和ＧＣ／ＭＳ联用分析,共鉴定了１４种有机物,其中主要有机物是酚类、吲哚和喹啉,分别占有机物总量的３９５％、２３９％和１７８％。     

Fluorine in the rocks and sediments of volcanic areas in central Italy: total content, enrichment and leaching processes and a hypothesis on the vulnerability of the related aquifers

Rock, sediment and water samples from areas characterised by hydrothermal alterations in the Sabatini and Vico Volcanic Districts, near Rome and the large city of Viterbo, respectively, were collected and analysed to determine the total fluorine (F) content and to understand the F geochemical background level in the volcanic districts of central Italy. Leaching and alteration processes controlling the high concentration of F in water were also investigated. Fluorine concentrations were directly determined (potentiometrically) by an F selective electrode in water samples, while the procedure for rock samples included preliminary F dissolution through alkaline fusion. F concentrations higher than 800 mg kg(-1) were commonly found in the analysed rocks and sediments; the concentration depended on the lithology and on the distance from the alteration areas. A specific successive sampling campaign was conducted in three areas where the F content in sediments was particularly high; in the same areas, measurements of CO(2) flux were also performed to investigate the possible deep origin of F. To verify the relationships among the high F contents in rocks and sediments, the leaching processes involved and the presence of F in the aquifer, we also collected water samples in the western sector of the Sabatini Volcanic District, where hydrothermal manifestations and mineral springs are common. The data were processed using a GIS system in which the F distribution was combined with morphological and geological observations. The main results of our study are that (1) F concentrations are higher in volcanic and recently formed travertine (especially in hydrothermally altered sediments) than in sedimentary rocks and decrease with distance from hydrothermal alteration areas, (2) F is more easily leached from hydrothermally altered rocks and from travertine and (3) sediments enriched with F may indicate the presence of deep regional fractures that represent direct pathways of hydrothermal fluids from the crust to the surface.     

利用Triolein-半渗透膜采样技术测定淮河水中的有毒有机污染物

利用 Triolein 半渗透膜采样技术 ( Triolein SPMD)采集了淮河信阳、淮南断面水样 ,测定了采样器中多氯联苯、多环芳烃、取代苯等有毒有机污染物浓度。污染物在 SPMD酯中高浓度富集 ,使其定性和定量更加容易和准确。根据SPMD酯 水分配平衡理论 ,进一步估算得到目标污染物在水中的平均浓度。本研究证明 Triolein SPMD技术可用于水中多氯联苯、多环芳烃、取代苯等污染物的采集和定量分析 ,可在我国的优先污染物监测、控制工作中发挥作用。     

Performance optimisation of a passive sampler for monitoring hydrophobic organic pollutants in water

The performance of an integrative passive sampler that consists of a C18 Empore disk sorbent receiving phase fitted with low density polyethylene membrane was optimised for the measurement of time-weighted average concentrations of hydrophobic micropollutants in water. A substantial improvement of sampling characteristics including the rate of sampling and the sampling precision was achieved by decreasing the internal sampler resistance to mass transfer of hydrophobic organic chemicals. This was achieved by adding a small volume of n-octanol, a solvent with high permeability (solubility [times] diffusivity) for target analytes, to the interstial space between the receiving sorbent phase and the polyethylene diffusion-limiting membrane.     

Investigation of the aerosol structure over an urban area using a polarization lidar

The paper presents a lidar study of the aerosol structure in the planetary boundary layer in the case of radiation fog and haze. A conceptual model of the dynamics of the depolarization coefficient profile during the mixing layer development, taking into account the presence of a multilayered inversions and radiation fogs, is proposed. Various techniques are employed in the processing of the lidar signal in order to determine the mixing layer height as well as more details of the aerosol structure in the low atmosphere, namely, finding the maximum of the signal returned from the lowest temperature inversion, the crossing point of the S function's first derivative with the x axis, and profiles of the depolarization ratio. After the complete destruction of the stable stratification, a low constant value of the depolarization ratio within the newly formed mixing layer is being observed. The study of stable boundary layer disintegration and convective boundary layer formation in the presence of fogs and/or clouds is of both scientific and practical significance in what concerns the protection of the environment and the aviation meteorology.     

Urban and suburban aerosol in Yokohama, Japan: a comprehensive chemical characterization

This article analyses elemental composition of suspended particulate matter (SPM) samples collected monthly from 1999 to 2005 at two locations in Yokohama, Japan. Microwave digestion and inductively coupled plasma mass spectroscopy was employed to measure Mg, Al, Ca, V, Cr, Mn, Ni, Cu, Zn, Ga, As, Se, Rb, Sr, Ag, Cd, Cs, Ba, Pb, and Bi. Water-soluble ions (Na^?+?, NH₄ ^?+?, K^?+?, Ca^2?+?, Cl^???, NO₃ ^???, and SO₄ ^2???) and carbonaceous mass (elemental and organic carbon) were detected using ion chromatograph and CHN analyzer, respectively. The results indicate that the composition of SPM on one of the sites is determined by automobile emissions and on the other by industrial combustions. The impact of the emission regulations for automobiles in large Japanese cities, which were enacted during 2002 and 2003, on the SPM composition of the samples is also studied.     

大气颗粒物样品中有机碳和元素碳的测定

采用元素分析仪测定大气颗粒物样品中有机碳、元素碳。应用商业化仪器元素分析仪 ,在燃烧炉温度为 4 50°C时 ,一步测出样品中有机碳的含量 ;再运用加酸的方法除去样品中的碳酸盐 ,然后在燃烧炉温度为 950°C时测出样品中有机碳、元素碳含量之和。通过差减计算 ,得出元素碳的值。有机碳、元素碳测量的标准偏差平均值分别为 0 2 5%、0 50 %。     

Lettuce plants as bioaccumulators of trace elements in a community of central Italy

A survey, based on the use of vascular plants to describe the distribution of selected elements (21 in total) was performed in 11 sites in the area of Castelfiorentino (Tuscany, Central Italy) differing for land use, from urban to industrial and rural areas. Lettuce plants grown under standardized conditions were positively used as biodeposimeters of airborne trace elements. Washing was found to be highly significant in reducing concentrations of many elements in the samples, suggesting a general surface contamination of leaves. The typical crustal element Al showed good correlations with Co, Fe, Li and V; on the contrary, Zn and Cd were intercorrelated and showed no connection with crustal indicators. Lead was still a relevant environmental presence, as the experiments were carried out before the ban of leaded gasoline. Source apportionment by factor analysis put in evidence a major contribution of crustal materials, followed by man-related activities; a minor role was ascertained for marine aerosol. A comparison was made between analytical data of lettuce plants grown in our experimental sites and a bulk of commercial lettuce purchased at a local supermarket. It should be stressed how Cu concentrations of commercial material were significantly higher than those found in our plants; this is likely caused by phytosanitary treatments.