Occurrence and fate of four novel brominated flame retardants in wastewater treatment plants

Four novel brominated flame retardants (NBFRs), i.e., decabromodiphenylethane (DBDPE), 1,2-bis(2,4,6-tribromophenoxy) ethane (BTBPE), pentabromoethylbenzene (PBEB), and hexabromobenzene (HBB) were studied in 377 liquid samples and 288 solid samples collected from 20 wastewater treatment plants. Lagoon, primary, secondary, and advanced treatment processes were included, in order to investigate NBFR occurrence and the effects of WWTP operational conditions on NBFR removal. Median influent and effluent levels were 14 to 3,700 and 1.0 to 180 pg/L respectively, with DBDPE being the highest in both. Overall median removal efficiencies for DBDPE, BTBPE, HBB, and PBEB across all process types were 81 to 93, 76 to 98, 61 to 97, and 54 to 97 %, respectively with advanced treatment processes obtaining the best removals. NBFRs removal was related to retention time, surface loading rate, and biomass concentration. Median NBFR levels in treated biosolids were 80 to 32,000 pg/g, influenced by solids treatment processes.     

Geographical distribution of non-PBDE-brominated flame retardants in mussels from Asian coastal waters

Hexabromocyclododecanes (HBCDs), 1,2-bis(2,4,6-tribromophenoxy) ethane (BTBPE), and decabromodiphenyl ethane (DBDPE) used as alternatives for polybrominated diphenyl ethers (PBDEs) are also persistent in the environment as PBDEs. Limited information on these non-PBDE brominated flame retardants (BFRs) is available; in particular, there are only few publications on environmental pollution by these contaminants in the coastal waters of Asia. In this regard, we investigated the contamination status of HBCDs, BTBPE, and DBDPE in the coastal waters of Asia using mussels as a bioindicator. Concentrations of HBCDs, BTBPE, and DBDPE were determined in green (Perna viridis) and blue mussels (Mytilus edulis) collected from the coastal areas in Cambodia, China (mainland), SAR China (Hong Kong), India, Indonesia, Japan, Malaysia, the Philippines, and Vietnam on 2003-2008. BTBPE and DBDPE were analyzed using GC-MS, whereas HBCDs were determined by LC-MS/MS. HBCDs, BTBPE, and DBDPE were found in mussels at levels ranging from <0.01 to 1,400, <0.1 to 13, and <0.3 to 22?ng/g lipid wt, respectively. Among the three HBCD diastereoisomers, α-HBCD was the dominant isomer followed by γ- and β-HBCDs. Concentrations of HBCDs and DBDPE in mussels from Japan and Korea were higher compared to those from the other Asian countries, indicating extensive usage of these non-PBDE BFRs in Japan and Korea. Higher levels of HBCDs and DBDPE than PBDEs were detected in some mussel samples from Japan. The results suggest that environmental pollution by non-PBDE BFRs, especially HBCDs in Japan, is ubiquitous. This study provides baseline information on the contamination status of these non-PBDE BFRs in the coastal waters of Asia.     

Conventional and emerging halogenated flame retardants (HFRs) in sediment of Yangtze River Delta (YRD) region,East China

The occurrence and distribution of polybrominated diphenyl ethers (PBDEs) and eleven non-PBDE halogenated flame retardants (HFRs) were investigated through the collection of marine and river sediment from Yangtze River Delta (YRD), East China. Among them, PBDEs, decabromodiphenyl ethane (DBDPE) and 1,2-dibromo-4-(1,2-dibromoethyl)cyclohexane (TBECH) were the three predominant HFRs with the highest detection frequencies in the sediment. Significant correlation between PBDEs and DBDPE indicated that they may have the similar emission sources. The production and use of DBDPE is growing rapidly and comparable concentrations between PBDEs and DBDPE in YRD sediment may suggest that DBDPE will likely become one of the major HFRs emerging in the environment in China. Of the seven detected non-PBDE HFRs, this is the first time that TBECH was reported in the Chinese environment and its predominance and prevalence in the YRD may imply its extensive use in these areas.     

Brominated flame retardants in the hair and serum samples from an e-waste recycling area in southeastern China: the possibility of using hair for biomonitoring

Hair samples and paired serum samples were collected from e-waste and urban areas in Wenling of Zhejiang Province, China. The PBDE and DBDPE concentrations in hair and serum samples from e-waste workers were significantly higher than those of non-occupational residents and urban residents. BDE209 was the dominating BFRs in hair and serum samples from the e-waste area, while DBDPE was the major BFRs from the urban area. Statistically significant correlations were observed between hair level and serum level for some substances (BDE209, DBDPE, BDE99, BDE47, BDE28, and BDE17), although the PBDE congener profiles in hair were different from those in the serum. A statistically significant positive correlation between the PBDE concentrations and the working age, as well as gender difference, was observed in e-waste workers. Different sources of PBDEs and DBDPE in three groups were identified by principal component analysis and spearman correlation coefficient. Hair is suggested to be a useful matrix for biomonitoring the PBDE exposure in humans.     

Levels and sources of brominated flame retardants in human hair from urban, e-waste, and rural areas in South China

Human hair and indoor dust from urban, e-waste, and rural areas in south China were collected and analyzed for brominated flame retardants (BFRs). BFRs concentrations in hair from occupational e-waste recycling workers were higher than those from non-occupational exposed residents in other sampling areas. Polybrominated diphenyl ethers (PBDEs) and decabromodiphenyl ethane (DBDPE) are two major BFRs in hair samples. The PBDE congener profiles in hair from the e-waste area are different from those from urban and rural areas with relatively higher contribution of lower brominated congeners. DBDPE, instead of BDE209, has become the major BFR in non-e-waste recycling areas. Significant correlations were found between hair level and dust level for DBDPE and BTBPE but not for PBDEs. The different PBDE congener profiles between dust and hair may suggest that exogenous exposure to the PBDE adsorbed on dust is not a major source of hair PBDEs.     

The metabolic fate of N-isopropyl-N-phenyloxamic acid in the rat and the milk goat.

Rats excreted the 14C from a single oral dose of N-isopropyl-N-[14C]phenyloxamic acid [I, a soil metabolite from 2-chloro-N-isopropylacetanilide (propachlor)] in approximately equal quantities in the urine (49.2%) and feces (48.2%). A milking goat given daily oral doses of [14C]-I (1 mg of I three times daily) excreted more 14C in the feces (56.6%) than it excreted in the urine. From both species, I accounted for 97 to 100% of the urinary 14C, and all of the 14C that was extractable from the feces (73 to 75% of the 14C in feces was extractable with methanol). Goat milk samples collected 16 hr after the last dose contained no detectable 14C. Tissue residues of 14C were determined.     

International cross-validation of a BOD5 surrogate

BOD5 dates back to 1912 when the Royal Commission decided to use the mean residence time of water in the rivers of England, 5 days, as a standard to measure the biochemical oxygen demand. Initially designed to protect the quality of river waters from extensive sewage discharge, the use of BOD5 has been quickly extended to waste water treatment plants (WWTPs) to monitor their efficiency on a daily basis. The measurement has been automatized but remains a tedious, time- and resource-consuming analysis. We have cross-validated a surrogate BOD5 method on two sites in France and in the USA with a total of 109 samples. This method uses a fluorescent redox indicator on a 96-well microplate to measure microbial catabolic activity for a large number of samples simultaneously. Three statistical tests were used to compare surrogate and reference methods and showed robust equivalence.     

Decabromodiphenyl ethane and decabromodiphenyl ether in Swedish background air

Decabromodiphenyl ethane (DPDPE) is a flame retardant that has been on the market for more than 20 years and is used as a replacement for decabromodiphenyl ether (BDE-209). Environmental data on DPDPE are scarce but for BDE-209, studies have shown that long-range transport in the atmosphere leads to contamination of remote regions. Given their similar physical-chemical properties, we hypothesized that this is also true for DPDPE. In this study we explored the European continent as a source for DBDPE by collecting air samples at a back-ground location in southern Sweden. Twelve samples with stable air mass back trajectories over the 24 h sampling period were analysed. BDE-209 and 5 polycyclic aromatic hydrocarbons (PAHs) were also included in the study. The concentration ranges of DBDPE and BDE-209 were similar, 0.077-7.9 and 0.093-1.8 pg m⁻³ air, respectively. The highest concentrations were detected when the air originated from the European continent and the lowest during periods with rather stagnant air over southern Scandinavia. The concentrations of DBDPE and BDE-209 did not co-vary, indicating that there are different major sources of the two compounds. In air, the compounds measured in this study are predominantly associated with particles. PAHs in the atmosphere are known to originate primarily from combustion processes and their concentrations were highly correlated with several measures of atmospheric particle concentration, i.e. PM 10, PM 2.5, soot, and N 450 (number of particles in the size range approximately 420-450 nm). No clear correlations were found between the concentrations of DBDPE or BDE-209 and any of the measures of particle concentrations, indicating that the emissions of these are not related to the major sources of emissions of soot or small particles.     

Large variation in lipid content, SigmaPCB and delta13C within individual Atlantic salmon (Salmo salar)

Many studies that investigate pollutant levels, or use stable isotope ratios to define trophic level or animal origin, use different standard ways of sampling (dorsal, whole filet or whole body samples). This study shows that lipid content, SigmaPCB and delta(13)C display large differences within muscle samples taken from a single Atlantic salmon. Lipid- and PCB-content was lowest in tail muscles, intermediate in anterior-dorsal muscles and highest in the stomach (abdominal) muscle area. Stable isotopes of carbon (delta(13)C) showed a lipid accumulation in the stomach muscle area and a depletion in tail muscles. We conclude that it is important to choose an appropriate sample location within an animal based on what processes are to be studied. Care should be taken when attributing persistent pollutant levels or stable isotope data to specific environmental processes before controlling for within-animal variation in these variables.     

Simultaneous analysis of thiabendazole,carbendazim and 2-aminobenzimidazole in concentrated fruit juices by liquid chromatography after a single mix-mode solid-phase extraction cleanup

A method using liquid chromatography and a single mix-mode solid-phase extraction cleanup for the simultaneous analysis of thiabendazole [2-(1,3-thiazol-4-yl)-1H-benzoimidazole], carbendazim [(methyl N-(1H-benzoimidazol-2-yl)-carbamate)] and 2-aminobenzimidazole (1H-benzimidazol-2-amine) in concentrated fruit juices is described. The three fungicides were isolated from the samples and concentrated by solid-phase extraction on Oasis MCX cartridges. The determination was performed by liquid chromatography with a diode array, detecting at 288 nm. In this method, the average recoveries from blank control juice samples spiked in a concentration range of 0.01–0.10 mg/kg were in the range of 81–95%, with relative standard deviations below 8%. Detection limits and limits of quantification were 4 μ g/kg and 10 μ g/kg, respectively, for each fungicide. Real juice samples were analyzed by the proposed method. The results were compared to those from liquid chromatography-tandem mass spectrometry.     

Spatial distribution and vertical profile of polybrominated diphenyl ethers, tetrabromobisphenol A, and decabromodiphenylethane in river sediment from an industrialized region of South China

Polybrominated diphenyl ethers (PBDEs), tetrabromobisphenol A (TBBPA), and decabromodiphenylethane (DBDPE) were detected in fifteen surface sediments and two sediment cores collected from a river in one heavily industrialized region of South China. TBBPA and DBDPE were detected with concentrations ranging from 3.8 to 230 ng/g dw and from 23 to 430 ng/g dw, respectively. Σtri-hepta-BDEs and Σnona-deca-BDEs ranged from 0.7 to 7.6 ng/g dw and from 30 to 5700 ng/g dw, respectively. Σtri-hepta-BDEs showed an increasing trend whereas for Σnona-deca-BDE two sediment cores revealed a decreasing trend in more recent sediment layers which may attributed to the introduction of DBDPE. The rapid increasing trend for TBBPA and DBDPE in recent sediment layers well reflected the rising demand of these two compounds in study area.     

Sample storage and extraction efficiencies in determination of polycyclic and nitro musks in sewage sludge

Analytical technology is continuously improving, developing better methods for isolating and concentrating trace compounds in environmental samples. Polycyclic and nitro musks (PNMs) are one group of emerging trace compounds detected in municipal wastewater. Differences in sample storage, preparation, and extraction methods for their measurement have led to variability in results. We analyzed 11 PNMs by GC/MS and compared the results of different storage times and extraction methods (supercritical fluid (SFE) or microwave-assisted (MAE)) for 202 samples of primary sludge, waste activated sludge (WAS), raw sludge, and aerobically/anaerobically digested biosolids collected from Canadian municipal wastewater treatment plants. Sixty-three air-dried samples were extracted by SFE, and 139 air-dried, centrifuged, or filtered samples were extracted by MAE. The mean surrogate recoveries were 89% (standard deviation (SD)=11%) for d(10)-anthracene by SFE and 88% (SD=14%) for d(10)-phenanthrene by MAE. Storage study results showed that PNM concentrations changed by a mean of 7% and 9% for primary sludge and WAS respectively after four weeks and decreased up to 25% after 13.5 months of storage in amber glass containers at -18 degrees C. Air-drying of sludge at room temperature caused losses of about 50% of PNM concentrations compared to centrifugation. The proportions of PNMs present in the liquid phase of sludge samples were less than 5% compared to proportions in the sludge solids. The most complete liquid-solid separation was achieved by filtration of frozen/thawed sludge samples, producing a liquid phase that contained less than 1% of the total musk content of the sample.     

High performance liquid chromatographic method for residue determination of sulfosulfuron

A method was developed for sulfosulfuron [(1-(2-ethylsulfonylimidazo [1,2-a] pyridin-3-ylsulfonyl)-3-(4,6-dimethoxy pyrimidin-2yl)] and its three major metabolites by HPLC utilizing photodiode array detector. The method makes use of Lichrosphere RP-8 column and acetonitrile:water:orthophosphoric acid (80:20:0.1 v/v/v) as mobile phase at a flow rate of 1 ml min(-1). Using these condition sulfosulfuron, and compounds II, III and IV were resolved with distinct Rt of 2.088, 2.216, 2.302 and 2.476 minutes, respectively. Sulfosulfuron residues were analysed in soil, wheat grain and straw samples by extracting with a mixture of acetonitrile and 2 M ammonium carbonate (100 ml, 9:1, v/v) using horizontal shaker for soil and Soxhlet apparatus for wheat grain and straw samples. The extracts were cleaned up by partitioning with dichloromethane in case of soil and hexane followed by dichloromethane for plant samples. The percent recovery ranged between 71 to 75.2 for soil and 70.8 to 74.7 for plant samples. The limit of determination of sulfosulfuron was 0.25 microg g(-1).     

The three-dimensional structural characterization of hexachlorocyclopentenyl-dibromocyclooctane (HCDBCO)

The (1)H NMR spectrum and the crystal structure of HCDBCO [(1R,2R,5R,6R,9S,10S)-5,6-dibromo-1,10,11,12,13,13-hexachlorotricyclo[8,2,1,0(2,9)]-tridec-11-ene)] are reported. The measured dihedral angles from the X-ray structure correlate very well with those calculated from the proton-proton coupling constants indicating that the conformations in solution and in the solid state are probably very similar. Attempts at calculating the 3D model structure of HCDBCO only produced a very poor match between the measured dihedral angles between vicinal protons and the observed proton-proton coupling constants from the (1)H NMR spectrum. GC/MS analysis with an injector temperature of 250 degrees C produced minor amounts of debrominated HCDBCO. Reducing the temperature to 200 degrees C eliminated this problem.     

Investigations of ash topography/morphology and their relationship with heavy metals leachability

The leachability of heavy metals such as chromium (Cr), lead (Pb) and cadmium (Cd) from the ash material obtained from waste combustion was studied. The effects of ash surface topography and morphology on the leachability of these elements were examined using atomic force microscopy (AFM) and scanning electron microscopy (SEM). The AFM (scan size 10 x 10 microns) and SEM images of the simulated ash pellet obtained at various operating temperatures (1000, 1400 and 1500 degrees C) showed significant microstructural and topographical changes. Ash pellets treated at 1000 degrees C contain porous and non-continuous surface. On the other hand, the ash pellet obtained at higher temperature (1500 degrees C) was found to contain a smooth, continuous and non-porous surface. The AFM height profile studies indicated that the top surface variation of the ash pellet at 1000, 1400 and 1500 degrees C were found to be -40.0 to 25.5, -3.7 to 4.7 and -0.10 to 0.66 nm respectively. The SEM analyses also confirmed the presence of smooth, non-porous outer surface of ash formed at 1500 degrees C. In addition, it also showed the presence of compact and rigid interior for the same ash pellet. The leachability of the heavy metals was determined using standard toxicity characteristic leaching procedure (TCLP) test and the samples were analysed using atomic absorption spectroscopy. The results showed that the TCLP leaching ratios of the heavy metals were Cr = 0.30, Pb = 0.05 and Cd = 0.09 at 1000 degrees C. However, the ash obtained at 1400 degrees C showed negligible heavy metals leaching ratio while at 1500 degrees C no leachability was detected (TCLP concentration dropped to nondetectable levels). The use of high temperature treatment enabled the immobilization of heavy metals in the ash preventing their leaching. Such ash can be considered as a non-hazardous material for reuse or safe disposal.     

Synthesis, isolation and purification of C10-C13 polychloro-n-alkanes for use as standards in environmental analysis

Short chain (C10-C13) polychloro-n-alkanes (sPCAs) mixtures were synthesized by refluxing pure n-alkane (> 99%) with sulfuryl chloride (SO2Cl2) in the presence of UV-light (550 W). The free radical initiated reactions produced analogs containing approximately 4-9 chlorine atoms on each carbon chain. Purification of reaction products was achieved by adsorption chromatography on Florisil. The products were characterized by high-resolution gas chromatography/mass spectrometry (HRGC/MS) operated in the electron capture negative ionization (ECNI) and in electron ionization (EI) modes. Individual standards can now be combined to create standards whose profiles resemble that of environmental samples. Quantification of a known amount of the newly synthesized sPCAs mixture, using an industrial formulation as an external standard, resulted in an overestimation (approximately 28%) in its true value.     

Evaluation of spatial distribution and accumulation of novel brominated flame retardants,HBCD and PBDEs in an Italian subalpine lake using zebra mussel (Dreissena polymorpha)

Because of the reduction in the use of polybrominated diphenyl ethers (PBDEs) and hexabromocyclododecane (HBCD), novel brominated flame retardants (NBFRs), including 1,2-bis(2,4,6-tribromophenoxy) ethane (BTBPE), decabromodiphenyl ethane (DBDPE), hexabromobenzene (HBB), and pentabromoethylbenzene (PBEB), started to be marketed as alternatives to the banned formulations. In this study, the spatial distribution and accumulation of NBFRs, PBDEs, and HBCD in the biota have been investigated in the littoral compartment of a large and deep subalpine lake (Lake Maggiore, Northern Italy), using zebra mussel Dreissena polymorpha and roach (Rutilus rutilus) as bioindicators. To our knowledge, this is the first study reporting the contamination of NBFRs in the freshwater invertebrate D. polymorpha. Contamination of zebra mussel due to PBEB, HBB, and BTBPE was low, ranging from 0.9 to 2.9 ng/g lipid weight, from 1.1 to 2.9 ng/g l.w., and from 3.5 to 9.5 ng/g l.w., respectively. PBEB and BTBPE in roach were always below the detection limit, while the contamination of HBB ranged from < limits of detection (LOD) to 1.74 ng/g l.w., indicating a weak contamination. DBDPE was < LOD in all the considered biological samples. Finally, HBCD was detected in all organic tissues with mean concentrations up to 74.4 ng/g l.w. PBDE results, supported by principal component analysis elaboration, suggested a possible contamination due to the congeners composing the penta- and deca-BDE technical formulations, which are present in the Lake Maggiore basin. The biomagnification factor values showed that tetra- and penta-BDE biomagnified, while octa-, nona-, and deca-BDE were still bioavailable and detectable in the fish muscles, but they do not biomagnified. Considering the other BFRs, only HBCD showed a moderate biomagnification potential.     

A passive sampling method for radiocarbon analysis of atmospheric CO2 using molecular sieve

Radiocarbon (¹⁴C) analysis of atmospheric CO₂ can provide information on CO₂ sources and is potentially valuable for validating inventories of fossil fuel-derived CO₂ emissions to the atmosphere. We tested zeolite molecular sieve cartridges, in both field and laboratory experiments, for passively collecting atmospheric CO₂. Cartridges were exposed to the free atmosphere in two configurations which controlled CO₂ trapping rate, allowing collection of sufficient CO₂ in between 1.5 and 10 months at current levels. ¹⁴C results for passive samples were within measurement uncertainty of samples collected using a pump-based system, showing that the method collected samples with ¹⁴C contents representative of the atmosphere. δ¹³C analysis confirmed that the cartridges collected representative CO₂ samples, however, fractionation during passive trapping means that δ¹³C values need to be adjusted by an amount which we have quantified. Trapping rate was proportional to atmospheric CO₂ concentration, and was not affected by exposure time unless this exceeded a threshold. Passive sampling using molecular sieve cartridges provides an easy and reliable method to collect atmospheric CO₂ for ¹⁴C analysis.     

Microbial bioavailability of pyrene in three laboratory-contaminated soils under aerobic and anaerobic conditions

Changes in bioavailability of pyrene in three uncontaminated soils were examined under aerobic and anaerobic conditions. Three soils were aerobically aged with pyrene and [(14)C]pyrene for 63 days, then incubated with water, nitrate, or sulfate under aerobic or anaerobic conditions for one year. Under aerobic conditions, microorganisms in two soils mineralized 58-82% of the added [(14)C]pyrene. The two soils amended with nitrate were seen to have enhanced aerobic mineralization rates. In one of these soils, non-extractable pyrene was seen to decrease over the course of the study due to desorption and mineralization, nitrate amendment enhanced this effect. Under anaerobic conditions, generated with a N(2):CO(2)(g) headspace, two soils with nitrate or sulfate amendment showed an increase in extractable [(14)C]pyrene at 365 days relative to inhibited controls, presumably due to microbially mediated oxidation-reduction potential and pH alteration of the soil environment. These observations in different soils incubated under aerobic and anaerobic conditions have important implications relative to the impact of microbial electron acceptors on bioavailability and transport of non-polar organic compounds in the environment suggesting that, given enough time, under the appropriate environmental conditions, non-extractable material becomes bioavailable. This information should be considered when assessing site specific exposure risks at PAH contaminated locations.     

Occurrence of alternative flame retardants in indoor dust from New Zealand: indoor sources and human exposure assessment

Due to worldwide restrictions on polybrominated diphenyl ethers (PBDEs), the demand for alternative flame retardants (AFRs), such as organophosphate flame retardants (OPFRs), novel brominated FRs (NBFRs) and hexabromocyclododecanes (HBCDs), has recently increased. Little is known about human exposure to NBFRs and OPFRs and that their levels in dust have been scarcely evaluated worldwide. To increase the knowledge regarding these chemicals, we measured concentrations of five major NBFRs, ten OPFRs and three HBCD isomers in indoor dust from New Zealand homes. Dust samples were taken from living room floors (n=34) and from mattresses of the same houses (n=16). Concentrations (ngg(-1)) of NBFRs were: 1,2-bis(2,4,6-tribromophenoxy)ethane (BTBPE) (<2-175), decabromodiphenyl ethane (DBDPE) (<5-1430), 2-ethylhexyl-2,3,4,5-tetrabromobenzoate (TBB) (<2-2285) and bis(2-ethylhexyl)-3,4,5,6-tetrabromophthalate (TBPH) (<2-640). For OPFRs, concentrations (ngg(-1)) ranged between: tri-ethyl-phosphate (TEP) (<10-235), tri-n-butyl-phosphate (TnBP) (<20-7545), tris-(2-chloroethyl)-phosphate (TCEP) (<20-7605), tris-(1-chloro-2-propyl) phosphate (TCPP) (20-7615), tri-(2-butoxyethyl)-phosphate (TBEP) (50-27325), tris-(2,3-dichloropropyl)-phosphate (TDCPP) (20-16560), tri-phenyl-phosphate (TPhP) (20-35190), and tri-cresyl-phosphate (TCP) (<50-3760). HBCD concentrations fell in the range <2-4100ngg(-1). BTBPE, DBDPE, TBPH, TBEP, and TnBP showed significant positive correlation (p<0.05) between their concentrations in mattresses and the corresponding floor dust (n=16). These data were used to derive a range of plausible exposure scenarios. Although the estimated exposure is well below the corresponding reference doses (RfDs), caution is needed given the likely future increase in use of these FRs and the currently unknown contribution to human exposure by other pathways such as inhalation and diet.