废铬渣无害化处理工艺方法

该发明公开了一种废铬渣无害化处理工艺。将废铬渣40％～45％、粉煤灰10％～15％、锌窑渣10％～15％、赤泥28％～30％（均为质量分数）混合均匀，破碎至50～80目后送入烧结炉内，于1000～1100℃高温下进行还原烧结物化处理，烧结后的混合料冷却2～3h后用水浸泡20～26h，用滤布滤出渣料，滤液用FeSO4作还原剂，其加入量为废铬渣中Cr^6＋含量的14～16倍，在滤液pH为8～8．5的条件下进行还原反应；将烧结过程产生的废气送至洗涤塔洗涤，产生的水蒸气排空。     

钛铁矿造孔核桃壳基活性炭的制备及其吸附性能

以核桃壳为原料,钛铁矿为造孔剂,制备钛铁矿造孔核桃壳基活性炭。实验结果表明：在氯化锌浓度为3mol/L、碳化时间为40min、碳化温度为400℃、钛铁矿加入量为5%的条件下,制得的钛铁矿造孔核桃壳基活性炭对苯酚、碱性品红、Pb²⁺的吸附量分别达到了156.80,181.35,35.84mg/g,比核桃壳活性炭分别提高了25.84%,18.59%,19.10%;钛铁矿作为造孔剂制备活性炭,可以降低碳化温度和缩短碳化时间,且对活性炭中孔的形成起促进作用,有利于对大分子物质和重金属的吸附去除。     

氟苯生产废水处理及资源化技术

采用酸化、萃取、反萃、除氟、电催化氧化技术处理氟苯生产废水（简称废水）。工艺条件为：以硫酸为酸化剂，pH小于等于1；萃取温度10～25℃，搅拌时间大于4min，油水比（萃取剂与废水的体积比）1：4．0；反萃碱油比（NaOH溶液体积与油相体积比）1：3，NaOH质量分数10％；除氟时先加入2倍理论计算量的氯化钙、后加入氧化钙调pH至7～8；电催化氧化时粒子群电催化反应器槽电流2．0～2．5A，停留时间40～60min。处理后废水的COD、苯酚、F^-、石油类去除率分别高于99．3％，99．9％，99．8％，99．9％，苯酚回收率高于93．5％；出水COD、苯酚、F^-、石油类的浓度低于GB8978—1996《污水综合排放标准》中的一级排放标准。     

利用废硅藻土制备白炭黑

以废弃硅藻土为原料,采用硫酸酸浸除杂、氢氧化钠合成硅酸钠、硫酸酸化,再经清洗、干燥等步骤,制得白炭黑。考察了不同因素对制备效果的影响。实验结果表明,酸浸最佳工艺条件为：硫酸质量分数17％,酸浸温度40℃,液固比（硫酸溶液与废弃硅藻土的质量比）3．0：1;碱处理最佳工艺条件为：碱加入量（氢氧化钠与酸浸后硅藻土的质量比）0．4,碱处理时间60min。在此条件下制备出的白炭黑的总产率可达46．7％,产品质量符合HGT3061—1999《橡胶配合剂沉淀水合二氧化硅技术条件》中的D类标准,可实现废弃硅藻土的资源化利用。     

生物细胞载体的制备方法

该专利公开了一种生物细胞载体的制备方法。其制备工艺为：(1)制备生物细胞载体专用树脂；(2)制备生物细胞载体的中空纤维；(3)生物细胞载体致孔剂处理。该发明具有制备工艺简单，操作方便，生物细胞载体比重小、柔软、耐生物腐蚀和纤维壁微孔分布均匀，纵横交叉密度大等优点，适用于培养生物细胞的生长载体、废水处理工程的微生物生长载体、水净化工程的反渗透膜和蓄电池的隔离膜等。／CN1556207，2004—12—22     

改性粉煤灰吸附-高级氧化法处理奥里油废水

将氯化铁改性粉煤灰（简称改性粉煤灰）吸附处理与高级氧化和生物处理等技术进行优化组合,以期得到简便而有效的处理奥里油废水（简称废水）的组合工艺。研究结果表明：在废水COD平均为4600mg／L、改性粉煤灰加入量为50g／L、废水pH为7～9、吸附时间为1h的条件下,COD去除率达30％。采用“改性粉煤灰一次吸附-湿式均相催化氧化-厌氧生物过程-改性粉煤灰二次吸附”组合工艺处理废水时,改性粉煤灰不但具有较好的预处理效果,且还有较好的后处理能力;湿式均相催化氧化的催化剂用量少（Cu（NO3）2为2．0g／L）、操作条件温和（2．5MPa,180℃,pH5—7,1h）;厌氧生物过程中不需特殊筛选的菌种,易操作控制;经该组合工艺处理后,废水COD从4600mg／L降至55mg／L,COD去除率为98．4％,达到GB8978-1996《污水综合排放标准》的一级排放标准。     

有机磷阻燃剂生产废水预处理工艺研究

采用液膜萃取—酸析沉降—络合萃取组合工艺对有机磷阻燃剂生产废水进行预处理.最佳工艺条件为:液膜萃取时,液膜油相(表面活性剂与煤油的混合液)与内水相(H2SO4溶液)的体积比2∶1、乳化液膜与废水的体积比1∶8、废水pH 13.0,硫酸体积分数10％、煤油中表面活性剂质量浓度30 g/L、液膜萃取时间 15 min;酸析沉降时,废水pH l.0,酸析沉降时间30 min;络合萃取时,络合萃取剂(烷基叔胺N235与煤油的混合液)中烷基叔胺N235体积分数30％,络合萃取剂与废水的体积比1∶4,废水pH l.0,络合萃取时间30 min.在此最佳处理条件下,废水COD总去除率可达93％,吡啶去除率达99.9％以上,总磷去除率可达97％,BOD5/COD提高至0.32,有利于后续生化处理.     

Fenton氧化-生物接触氧化工艺处理甲醛和乌洛托品废水

采用Fenton氧化一生物接触氧化工艺处理含甲醛和乌洛托品的模拟废水（简称废水），在H2O2（体积分数30％）加入量2．5g／L、H2O2与Fe^2＋质量浓度比3．75、反应时间3h、不调节废水初始pH的Fenton氧化预处理最佳操作条件下，废水COD从1000mg／L左右降至300mg／L，COD去除率达72％。原废水完全无法直接进行生化处理，经Fenton氧化预处理后其BOD，／COD约为0．5，易于生化处理。Fenton氧化一生物接触氧化工艺处理废水，生物接触氧化停留时间为12h时，废水COD去除率高达94％，处理后出水COD小于70mg／L，处理效果很好。     

碱解—Fenton氧化预处理灭多威生产废水

采用碱解—Fenton氧化工艺对灭多威生产废水进行处理，考察了液碱加入量、碱解温度和碱解催化剂对碱解处理效果的影响，分析了影响Fenton氧化效果的主要因素。实验结果表明：在液碱加入量5%(w)、碱解催化剂加入量5 g/L、碱解温度150℃、碱解时间5 h、双氧水加入量3%(w)、Fenton反应温度65℃、反应时间70 min的最佳工艺条件下，灭多威生产废水经碱解—Fenton氧化工艺处理后，COD由39 347.5 mg/L降至5 390.6 mg/L，去除率为86.3%，灭多威肟质量浓度由9 021.2 mg/L降低至98.1 mg/L，去除率为98.9%，灭多威质量浓度由3 354.5mg/L降至未检出，BOD₅/COD由0.02提高至0.34；采用碱解—Fenton氧化工艺处理1 t灭多威生产废水的药剂成本为103.01元。     

粉煤灰-粉煤灰合成沸石对Cs~+的固化

以电厂废弃物粉煤灰为原料、采用碱熔-水热法制备了粉煤灰合成A型沸石(以下简称沸石),再以沸石对溶液中的Cs+进行分离富集,最后在碱激发剂的作用下以粉煤灰和吸附后的沸石制得地聚合物固化体。对固化体的性能进行了评价,并探讨了固化机理。实验结果表明:在吸附温度25℃、初始Cs+质量浓度100 mg/L、固液比10.0 g/L的条件下,沸石对的Cs+的吸附率达98%,比粉煤灰提高了2倍以上;沸石掺量为20%~30%(w)时,固化体的抗压强度符合GB 14569.1—2011要求,固化体中Cs+的42 d浸出率和累计浸出分数均远优于GB 14569.1—2011限值,表现出优异的抗浸出性能。     

Review of the kinetics of alkaline degradation of cellulose in view of its relevance for safety assessment of radioactive waste repositories

The degradation of cellulose (a substantial component of low- and intermediate-level radioactive waste) under alkaline conditions occurs via two main processes: a peeling-off reaction and a basecatalyzed cleavage of glycosidic bonds (hydrolysis). Both processes show pseudo-first-order kinetics. At ambient temperature, the peeling-off process is the dominant degradation mechanism, resulting in the formation of mainly isosaccharinic acid. The degradation depends strongly on the degree of polymerization (DP) and on the number of reducing end groups present in cellulose. Beyond pH 12.5, the OH^- concentration has only a minor effect on the degradation rate. It was estimated that under repository conditions (alkaline environment, pH 13.3-12.5) about 10% of the cellulosic materials (average DP = 1000-2000) will degrade in the first stage (up to 10⁵ years) by the peeling-off reaction and will cause an ingrowth of isosaccharinic acid in the interstitial cement pore water. In the second stage (10⁵-10⁶ years), alkaline hydrolysis will control the further degradation of the cellulose. The potential role of microorganisms in the degradation of cellulose under alkaline conditions could not be evaluated. Proper assessment of the effect of cellulose degradation on the mobilization of radionuclides basically requires knowing the concentration of isosaccharinic acid in the pore water. This concentration, however, depends on several factors such as the stability of ISA under alkaline conditions, sorption of ISA on cement, formation of sparingly soluble ISA-salts, etc. A discussion of all the relevant processes involved, however, is far beyond the scope of the presented overview.     

Study of Aging Characteristics of Ternary Blends of Polyethylenes—II

Six film samples of low-density polypropylene (LDPE)/linear LDPE (LLDPE)/high-density polypropylene (HDPE) with varying ratios of LDPE (20–45 ... wt%) and LLDPE (25–50 wt%) having a fixed amount of HDPE at 30 wt% were prepared by blown film extrusion technique. The samples were aged at four different temperatures, 55°, 70°, 85°, and 100°C, for four different time periods in the interval of between 150 hours and up to 600 hours. The change in the structure of various constituents and the formation of various oxygenated (peroxy and hydroperoxy) and unsaturated groups during thermo-oxidative degradation was discussed by infrared spectroscopy. The visiosity-average molecular weight was found to have decreased slowly in the initial aging hours and temperatures, whereas it decreased by 10% with its previous value tensile strength that is, 100°C when aged for 600 hours. The tensile strength of the sample first increased by 67% at 55°C and 89% at 70°C up to 450 hours, whereas the values increased by 52.5% at 85°C and 33.9% at 100°C when aged for 150 hours and then decreased. The percentage elongation at break increased by 2.7% at 55°C and 10.7% at 70°C for 150 and 300 hours of aging, respectively, whereas the percentage decreased when aged at 85°C and 100°C for up to 600 hours of aging. The values of gel content (percent) increased and initial degradation temperature decreased with aging time and temperature.     

Calculation of carbon balances for evaluation of the biodegradability of polymers

Establishing carbon balances has been proven to be an applicable and powerful tool in testing biodegradability of polymers. In controlled degradation tests at a 4-L scale with the model polymer poly(-hydroxybutyrate) (PHB), it was shown that the degree of degradation could not be determined with satisfactory accuracy from CO₂ release alone. Instead, the course of degradation was characterized by means of establishing carbon balances for the degradation of PHB withAcidovorax facilis and a mixed culture derived from compost. Different analytical methods for determining the different carbon fractions were adapted to the particular test conditions and compared. Quantitative determination of biomass and residual polymer were the main problems in establishing carbon balances. Amounts of biomass derived from protein measurements depend strongly on assumptions of the protein content of the biomass. Selective oxidation of biomass with hypochlorite was used as alternative, but here problems arose from insoluble metabolic products. Determination of soluble components with the method of chemical oxygen demand (COD) also includes empirical assumptions but seems acceptable if the dissolved carbon fraction is in the range of some 10% total carbon. Results confirm both analytical assays and theoretical approaches, in ending up at values very close to 100%, within an acceptable standard deviation range under test conditions comparable to standard test practice.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.     

Model of technological alternatives of production of sodium chromate (VI) with the use of chromic wastes

This article presents a mathematical model which describes the sodium chromate (VI) production process with the use of chromic waste as a substitution of natural raw materials. This model is a function of selected process parameters common for all of the examined alternatives and based on equations of material balance. Optimization of the elaborated technological alternatives of the production process with use of recycling of chromic waste has been evaluated by determining the extreme value of the quality indicator WJ. This indicator defines the quantity of waste created in the process. Optimization results enabled the selection of the optimal technological solution from all of the alternatives possible for use in industrial practice. Negative values of the indicator prove that there is the possibility of introducing to the process a larger quantity of waste than the one obtained in the process and transported to the storage heaps.     

化学品生物降解性的评价与预测

介绍了有机化学物质生物降解性的测定方法及其预测方法研究概况，并讨论了生物降解性评价的发展前景。     

Determination of the Burning Characteristics of a Slick of Oil on Water

The burning rate of a slick of oil on a water bed is characterized by three distinct processes, ignition, flame spread and burning rate. Although all three processes are important, ignition and burning rate are critical. The former, because it defines the potential to burn and the latter because of the inherent possibility of boilover. Burning rate is calculated by a simple expression derived from a one-dimensional heat conduction equation. Heat feedback from the flame to the surface is assumed to be a constant fraction of the total energy released by the combustion reaction. The constant fraction (χ) is named the burning efficiency and represents an important tool in assessing the potential of in situ burning as a counter-measure to an oil spill. By matching the characteristic thermal penetration length scale for the fuel/water system and an equivalent single layer system, a combined thermal diffusivity can be calculated and used to obtain an analytical solution for the burning rate. Theoretical expressions were correlated with crude oil and heating oil, for a number of pool diameters and initial fuel layer thickness. Experiments were also conducted with emulsified and weathered crude oil. The simple analytical expression describes well the effects of pool diameter and initial fuel layer thickness permitting a better observation of the effects of weathering, emulsification and net heat feedback to the fuel surface. Experiments showed that only a small fraction of the heat released by the flame is retained by the fuel layer and water bed (of the order of 1%). Ignition has been studied to provide a tool that will serve to assess a fuels ease to ignite under conditions that are representative of oil spills. Two different techniques are used, piloted ignition when the fuel is exposed to a radiant heat flux and flash point as measured by the ASTM D56 Tag Closed Cup Test. Two different crude oils were used for these experiments, ANS and Cook Inlet. Crude oils were tested in their natural state and at different levels of weathering, showing that piloted ignition and flash point are strong functions of weathering level.     

Mechanism of Microbial Degradation of Slow-Release Fertilizers

Methyleneureas are condensation products of urea and formaldehyde of different molecular mass and solubility; they are used in large amounts both as resins, binders, and insulating materials for industrial applications, as well as a slow-release nitrogen fertilizer for greens, lawns, or in bioremediation processes. In the present study, the microbial breakdown of these products was investigated. The nitrogen was released as ammonia and urea, and the formaldehyde released immediately oxidized via formiate to carbon dioxide. The enzymatic mechanism of metabolization of methyleneureas was studied in microorganisms isolated from soil, which were able to use these compounds as the sole source of nitrogen for growth. A strain of the Gram-negative bacterium Ralstonia paucula (formerly Alcaligenes sp. CDC group IVc-2) completely degraded methylenediurea and dimethylenetriurea to urea, ammonia, formaldehyde, and carbon dioxide. The enzyme initiating this degradation (methylenediurease) was purified and turned out to be different from the previously described enzyme from Ochrobactrum anthropi with regard to its regulation of expression and physicobiochemical properties. Fungal degradation of methyleneureas may occur via the formation of organic acids, thus leading to a nonenzymatic degradation of methyleneureas, which are unstable under acidic conditions.     

Effect of Degree of Substitution of Octenyl Succinate Starch on Enzymatic Degradation

Octenyl succinate starch of degree of substitution (ds) 0.03, 0.07, and 0.11 was synthesized in an aqueous medium. These compounds were then tested for the susceptibility to enzymatic degradation. The multiple-enzyme regime of -amylase, amyloglucosidase, and pullulanase was chosen for the evaluation. This combination of enzymes had been proven to degrade 99.5% of unmodified starch to glucose and hence was chosen for this study. It was found that even small amounts of subsituent caused a considerable decrease in the extent of degradation. The net extent of degradation decreased with increasing ds. Surprisingly, the amount of glucose from all three substituted substrates was quite similar, suggesting the effect small amounts of subtituent had on the enzymatic activity.     

Electron Microscope Observation of Biodegradation of Polymers

Biodegradable polymers generally decompose in the various media in our environments. These environments contain soils, seawater, and activated sludge. If biodegradable materials waste is discarded, they decompose in these media. The biodegradation process of biodegradable polymers was investigated by scanning electron microscopy. Polycaprolactone, polybutylene succinate, and P(3HB-co-3HV) were tested. The shapes of holes on the decomposing surfaces are different according to the biodegradation media. Semispherical holes are observed on the surfaces of polybutylene succinate films degraded in activated sludge and cracks are observed on the surfaces of polycaprolactone films degraded in soil.     

Structure-biodegradation relationships of polymeric materials. 1. Effect of degree of oxidation on biodegradability of carbohydrate polymers

The biodegradability of oxidized starch and inulin has been studied in relation to the degree of periodate oxidation to dialdehyde derivatives, by measuring oxygen consumption and mineralization to carbon dioxide. A higher degree of oxidation of dialdehyde starch and dialdchyde inulin results in a lower rate at which the polymers are biodegraded. It is demonstrated that the biodegradation rate of dialdehyde inulin derivatives decreases more than that of equivalent starch derivatives. The differences in biodegradation behavior between dialdehyde starch and dialdehyde inulin, resulting from comparable modifications, are discussed in terms of conformational structure.