Infiltration of PCE in a system containing spatial wettability variations

A two-dimensional infiltration experiment was conducted to investigate and quantify the effect of spatial wettability variations on DNAPL migration and entrapment in saturated sands. Experimental observations of tetrachloroethylene (PCE) infiltration showed that organic-wet sand lenses acted as very effective capillary barriers, retaining PCE and inhibiting its downward migration. A multiphase numerical simulator was used to model this sand box experiment. The simulator incorporates wettability-modified van Genuchten and Brooks-Corey capillary pressure/saturation relationships as well as Burdine and Mualem relative permeability relationships. PCE mass distributions, estimated by image analysis of digital photographs taken during the infiltration event, were compared to simulation results. Although both relative permeability models were qualitatively able to predict the PCE retention in the organic-wet layers, simulations with the Mualem model failed to capture the observed rate of PCE migration. A traditional multiphase simulator, incorporating water-wet capillary retention relations, failed to predict both PCE pathways and retention behavior. This study illustrates the potential influence of subsurface wettability variations on DNAPL migration and entrapment and supports the use of modified capillary relations in conjunction with the Burdine model in multiphase flow simulators.     

铁盐改性砂制备及其吸附Zn~(2+)的性能研究

通过改变石英砂表面的物理化学性质,提高石英砂的吸附效率,考察其对废水中的Zn~(2+)去除效果.以石英砂为载体,分别用反复高温加热法和反复碱性沉积法制备了三氯化铁改性砂、硝酸铁改性砂,测定2种方法制备的铁盐改性砂的表面含铁量、铁盐的酸稳定性及比表面积,并比较2种铁盐改性砂对Zn~(2+)的吸附效果.结果表明,三氯化铁改性砂、硝酸铁改性砂的比表面积分别为2.468、4.247 m~2/g,比石英砂比表面积分别提高6.910、12.612倍;在pH为中性条件下,石英砂对Zn~(2+)去除率为43%左右,三氯化铁改性砂对Zn~(2+)去除率达到70%左右,硝酸铁改性砂对Zn~(2+)去除率达到85%左右,表明铁盐改性砂对Zn~(2+)去除能力比石英砂有很大提高;铁盐改性砂对Zn~(2+)的吸附有一定容量,表面的活性中心越多,吸附能力越大;铁盐改性砂对Zn~(2+)的去除率随着pH的升高而增加,当pH>8.5时,Zn~(2+)去除率可达90%左右.     

Multiphase flow and transport in fractured clay/sand sequences.

A numerical model (Queen's University Multi-Phase Flow Simulator, QUMPFS) was used to assess the rate of trichloroethylene (TCE) dense, non-aqueous phase liquid (DNAPL) migration through fractured clay, with special attention focused on the influence of interbedded sand lenses. The presence of these sand lenses was found to increase the time required for the non-wetting phase to migrate through the full 30 m vertical extent of the clay sequence from a few days to several years. Applied vertical hydraulic gradients were found to be moderately influential in systems consisting solely of fractured clays, yet one of the dominant factors controlling speed of vertical migration when sand lenses were present. Larger displacement pressure of the sands relative to that of the fractures leads to slower DNAPL migration rates, due to the delays that occur during build-up of capillary pressures. Dissolution of DNAPL and subsequent matrix diffusion of the aqueous phase has little effect on the rate of DNAPL migration through systems consisting of fractured clay only, yet slows the rate of migration in systems containing sand lenses. In all cases examined, the rate of DNAPL loading to the lower aquifer far exceeded the rate of aqueous phase mass loading. It was also found that DNAPL reaches the lower aquifer at approximately the same time as the aqueous phase plumes even for systems experiencing downward groundwater flow due to the attenuation of the aqueous phase through matrix diffusion.     

表面活性剂强化抽出处理含水层中DNAPL污染物的去除特征

为明确表面活性剂强化抽出处理含水层中DNAPL污染物过程中表面活性剂的增强修复效果,及DNAPL自身理化性质和介质孔径的影响,利用数码图像分析技术对1,2-二氯乙烷和四氯乙烯2种DNAPL在石英砂填充的二维砂箱中的抽取迁移过程进行了实验模拟研究,并对抽出水样中DNAPL的浓度进行了测试分析。结果表明,实验条件下加入低浓度(0.18%)的十二烷基苯磺酸钠(SDBS)大幅提高了对弱透水层截留的2种DNAPL聚集体的抽出处理效率。1,2-二氯乙烷在该表面活性剂溶液中的表观溶解度远高于四氯乙烯,因此其短时间内的绝对去除率更高。SDBS强化抽出处理DNAPL的作用机理以增溶作用为主,而其增流作用使DNAPL迁移流动后分布面积增大,增加了与表面活性剂溶液接触的面积,对增溶作用起到促进效果。细粒介质中DNAPL迁移后的最大分布面积较大,因此体系中DNAPL的溶解速率较高。在DNAPL聚集体质量与水力梯度固定的条件下,油水界面张力越低,DNAPL的密度越大,DNAPL垂向迁移的风险就越大。本研究为修复工程中如何依据DNAPL种类与场地多孔介质的情况选择表面活性剂提供了参考。     

Comparison of capillary pressure relationships of organic liquid-water systems containing an organic acid or base

The presence of surface-active solutes such as organic acids and bases may have a profound influence on the transport of organic liquid contaminants through their impact on the constitutive relationship of capillary pressure vs. saturation. This relationship is a function of the interfacial tension and wettability of the system, which, in turn, depend on the pH and the concentration of organic acids and bases that are present. This study examines the impact of pH and the concentration on the interfacial tension, contact angle, and capillary pressure of systems consisting of tetrachloroethylene, water, and quartz containing either octanoic acid or dodecylamine. In general, the ionic form of the solute tended to remain in the aqueous phase and reduced the capillary pressure through its impact on the interfacial tension and contact angle; on the other hand, the neutral form of the solute partitioned into the organic liquid phase and had a lesser impact on the capillary pressure for the same total mass of solute. A comparison of these data with data generated in previous research in similar systems where o-xylene was the organic liquid showed that the trends are analogous. Thus, the behavior of these two solvent systems seems to be driven primarily by the aqueous phase speciation of the solute, and the differences between the capillary pressure relationships for the two systems could be attributed to the pure system interfacial tension.     

The impact of additives found in industrial formulations of TCE on the wettability of sandstone

The wettability of aquifer rocks is a key physical parameter which exerts an important control on the transport, residual trapping, distribution and eventual fate of chlorinated hydrocarbon solvents (CHSs) released into the subsurface. Typically chlorinated solvents are assumed to be non-wetting in water saturated rocks and unconsolidated sediments. However industrially formulated solvent products are often combined with basic additives such as alkylamines to improve their performance; and the mineral surfaces of aquifer rocks and sediments usually possess a range of acid and hydrogen-bonding adsorption sites. The presence of these sites provides a mechanism whereby the basic additives in CHSs can be adsorbed at the solvent phase/solid phase interface. Given the amphiphilic molecular structure of these additives, this may result in changes in the wetting conditions of the solid phase. The aim of this study was therefore to test this conjecture for two classes of additives (alkylamines and quaternary ammonium salts) that are often encountered in industrial solvent formulations. Wettability assessments were made on sandstone cores by means of measurements of spontaneous and forced water drainage and spontaneous and forced water imbibition and through contact angle measurements on a smooth quartz surface. No solvent/additive combination produced solvent wetting conditions, though dodecylamine and octadecylamine significantly reduced the water wetting preference of sandstone which frequently resulted in neutral wetting conditions. The large volume of spontaneous water drainage observed in wettability experiments involving cetyltrimethylammonium bromide and octadecyltrimethylammonium bromide, suggested that the sandstone cores in these tests remained strongly water wetting. However equilibrium static contact angles of around 60 degrees were measured on quartz suggesting that the sandstone surfaces should be close to neutral wetting conditions. This paradox was finally resolved by noting that contact between the solvent mixture and water in the sandstone core resulted in a final solvent phase which had an extremely low interfacial tension. It is therefore suspected that the observed spontaneous drainage of solvent from the core was driven by gravitational and buoyancy forces rather than strong water wetting conditions. Finally it was noted that the mobilisation of iron oxide coatings from the sandstone surface had a considerable influence in reducing the interfacial tension and in the formation and stabilisation of TCE/water emulsions.     

Secondary imbibition in NAPL-invaded mixed-wet sediments

A previously developed pore network model is used here to study the spontaneous and forced secondary imbibition of a NAPL-invaded sediment, as in the displacement of NAPL by waterflooding a mixed-wet soil. We use a 3D disordered pore network with a realistic representation of pore geometry and connectivity, and a quasi-static displacement model that fully describes the pore-scale physics. After primary drainage (NAPL displacing water) up to a maximum capillary pressure, we simulate secondary imbibition (water displacing NAPL). We conduct a parametric study of imbibition by varying systematically the controlling parameters: the advancing contact angles, the fraction of NAPL-wet pores, the interfacial tension, and the initial water saturation. Once the secondary imbibition is completed, the controlling displacement mechanisms, capillary pressures, relative permeabilities, and trapped NAPL saturations are reported. It is assumed that NAPL migrates into an initially strongly water-wet sediment, i.e., the receding contact angles are very small. However, depending on the surface mineralogy and chemical compositions of the immiscible fluid phases, the wettability of pore interiors is altered while the neighborhoods of pore corners remain strongly water-wet-resulting in a mixed-wet sediment. Here, we compare three different levels of wettability alteration: water-wet (advancing contact angles (20 degrees to 55 degrees), intermediate-wet (55 degrees to 120 degrees), and NAPL-wet (120 degrees to 155 degrees). The range of advancing contact angles and the fraction of NAPL-wet pores have dramatic effects on the NAPL-water capillary pressures and relative permeabilities. The spatially inhomogeneous interfacial tension has a minor impact on the trapped NAPL saturation and relative permeability to NAPL, and a slight effect on the relative permeability to water. The initial water saturation has a slight effect on the two-phase flow characteristics of water-wet sediments; however, with more NAPL-wet pores in the sediment, it starts to have a profound effect on the water and NAPL relative permeabilities.     

Mobilization of small DNAPL pools formed by capillary entrapment

We performed an experimental study to quantify the critical conditions for the mobilization of small pools of dense nonaqueous phase liquids (DNAPLs) that may form at capillary-heterogeneity boundaries. A series of experiments were conducted in columns packed with uniform sands arranged to create capillary heterogeneities. DNAPL pools readily formed in these packings and were more easily mobilized than trapped DNAPL ganglia. A model was developed to describe the critical conditions for DNAPL pool mobilization. Pool mobilization was expected when a dimensionless pool trapping number N(T)p> 1 while mobilization was observed in our experiments when N(T)p>0.76+/-0.16 (+/- 95% confidence interval). The difference between the model prediction and the experimental observations was attributed to experimental error. Using this model for DNAPL pool mobilization, a simple numerical experiment was conducted to illustrate use of the model and to explore the effect of scale on the critical conditions for pool mobilization. With an increase in system scale flow bypassing around the DNAPL pool increased and the system-averaged conditions for the onset of mobilization changed: a greater system-average Darcy flux or lower interfacial tensions were required for DNAPL pool mobilization. This result illustrates the importance of system scale on mobilization of DNAPL pools in systems with capillary heterogeneities.     

Streaming potential method for characterizing interaction of electrical double layers between rice roots and Fe/Al oxide-coated quartz in situ

The interaction between rice roots and Fe/Al oxide-coated quartz was investigated through zeta potential measurements and column leaching experiments in present study. The zeta potentials of rice roots, Fe/Al oxide-coated quartz, and the binary systems containing rice roots and Fe/Al oxide-coated quartz were measured by a specially constructed streaming potential apparatus. The interactions between rice roots and Fe/Al oxide-coated quartz particles were evaluated/deduced based on the differences of zeta potentials between the binary systems and the single system of rice roots. The zeta potentials of the binary systems moved in positive directions compared with that of rice roots, suggesting that there were overlapping of diffuse layers of electric double layers on positively charged Fe/Al oxide-coated quartz and negatively charged rice roots and neutralization of positive charge on Fe/Al oxide-coated quartz with negative charge on rice roots. The greater amount of positive charges on Al oxide led to the stronger interaction of Al oxide-coated quartz with rice roots and the more shift of zeta potential compared with Fe oxide. The overlapping of diffuse layers on Fe/Al oxide-coated quartz and rice roots was confirmed by column leaching experiments. The greater overlapping of diffuse layers on Al oxide and rice roots led to more simultaneous adsorptions of K⁺ and NO₃ ^? and greater reduction in leachate electric conductivity when the column containing Al oxide-coated quartz and rice roots was leached with KNO₃ solution, compared with the columns containing rice roots and Fe oxide-coated quartz or quartz. When the KNO₃ solution was replaced with deionized water to flush the columns, more K⁺ and NO₃ ^? were desorbed from the binary system containing Al oxide-coated quartz and rice roots than from other two binary systems, suggesting that the stronger electrostatic interaction between Al oxide and rice roots promoted the desorption of K⁺ and NO₃ ^? from the binary system and enhanced overlapping of diffuse layers on these oppositely charged surfaces compared with other two binary systems. In conclusion, the overlapping of diffuse layers occurred between positively charged Fe/Al oxides and rice roots, which led to neutralization of opposite charge and affected adsorption and desorption of ions onto and from the charged surfaces of Fe/Al oxides and rice roots.     

Removal of DNAPL contamination from the saturated zone by the combined effect of vertical upward flushing and density reduction

A common aspect of innovative remediation techniques is that they tend to reduce the interfacial tension between the aqueous and non-aqueous phase liquids, resulting in mobilization of the organic contaminant. This complicates the remediation of aquifers, contaminated with Dense Non-Aqueous Phase Liquids (DNAPLs), as they are likely to migrate downwards, deeper into the aquifer and into finer layers. A possible solution is the use of swelling alcohols, which tend to reduce the density difference between the aqueous phase and the DNAPL. To avoid premature mobilization upon the initial contact between the DNAPL and the alcohol, several researchers have proposed the use of vertical upward flow of the alcohol. In this paper, we present an equation, which describes the upward mobilization of both continuous and discontinuous DNAPLs and so the important parameters governing the upward controlled mobilization of the DNAPL. The need and required magnitude of this specific discharge was investigated by conducting four column experiments in which the initial density of the DNAPL and the permeability was varied. It was shown that the required flow velocities increase with the permeability of the porous medium and the initial density difference between the aqueous phase and the DNAPL. Whenever the specific discharge falls below the critical value, the DNAPL moves downward. A second set of column experiments looked at the impact of permeability of porous medium on the solubilization and mobilization of DNAPL during alcohol flooding. Columns, packed with coarse or fine sand, containing a residual trichloroethylene (TCE) or perchloroethylene (PCE) saturation were flushed with the alcohol mixture at a fixed specific discharge rate. The induced pressure gradients in the aqueous phase, which were higher in the fine sand, resulted for this porous medium in extensive mobilization of the DNAPL against the direction of the buoyancy force. The density of the first NAPL coming out of the top of the fine sand was close to that of the pure DNAPL. In the coarser sand, the pressure gradients were sufficient to prevent downward migration of the DNAPL, but upward mobilization was minimal. The predominant removal mechanism in this case was the much slower solubilization.     

Waste green sands as reactive media for the removal of zinc from water

Waste green sands are industrial byproducts of the gray iron foundry industry. These green sands are composed of fine silica sand, clay binder, organic carbon, and residual iron particles. Because of their potential sorptive and reactive properties, tests were performed to determine the feasibility of using green sands as a low cost reactive medium in permeable reactive barriers (PRBs). Serial batch kinetic tests and conventional batch sorption tests were conducted to determine the removal characteristics for zinc in aqueous solutions. Removal characteristics for zinc in the presence of green sands are comparable to those of Peerless iron, a common reactive medium used in PRBs. High removal capacities for zinc of green sands are attributed to clay, organic carbon, and residual iron particles, which are known sorptive media for heavy metals. Furthermore, high pH values in the presence of clay and residual iron particles enhanced sorption and precipitation of zinc.     

Effects of surface coatings on electrochemical properties and contaminant sorption of clay minerals

Surface charges play a major role in determining the interactions of contaminants with soils. The most important sources of soil charges are clay mineral colloids, whose electrochemical properties are usually modified by metal-oxides and organic matter in natural environments. In this study, effects of coatings of organic matter and Fe- and Al-oxides on a series of electrochemical properties and heavy metal sorption of three clay minerals (kaolinite, montmorillonite and illite) predominant in natural soils were investigated using batch techniques. The results indicate that the coatings increased the specific surface area of the clay minerals, except for the Al-oxide coated montmorillonite and organic matter coated 2:1 clay minerals. The sesquioxide coatings increased amount of positive charges but decreased negative charges. This causes great reduction of the negative potential on the clay surfaces, shift of the zero point of charge to a higher pH, and promotion of fluoride sorption due to presence of more OH- and OH2 on the oxide surfaces than on the clay surfaces. In contrast, the organic coating significantly increased the negativity of surface charges, and thus the zero point of charge and zeta-potential of the clays dropped down. The organic coating also induced a reduction of fluoride sorption on the clays. With respect to the sorption of lead and cadmium, the sesquioxide coatings produced insignificant effects. The experiments of lead/cadmium competitive sorption show that on both the oxide-coated surface and the original clay surface there exist different types of sites, each of which preferentially binds with a heavy metal.     

Transport and deposition of functionalized CdTe nanoparticles in saturated porous media

Comprehensive understanding of the transport and deposition of engineered nanoparticles (NPs) in subsurface is required to assess their potential negative impact on the environment. We studied the deposition behavior of functionalized quantum dot (QD) NPs (CdTe) in different types of sands (Accusand, ultrapure quartz, and iron-coated sand) at various solution ionic strengths (IS). The observed transport behavior in ultrapure quartz and iron-coated sand was consistent with conventional colloid deposition theories. However, our results from the Accusand column showed that deposition was minimal at the lowest IS (1mM) and increased significantly as the IS increased. The effluent breakthrough occurred with a delay, followed by a rapid rise to the maximum normalized concentration of unity. Negligible deposition in the column packed with ultrapure quartz sand (100mM) and Accusand (1mM) rules out the effect of straining and suggests the importance of surface charge heterogeneity in QD deposition in Accusand at higher IS. Data analyses further show that only a small fraction of sand surface area contributed in QD deposition even at the highest IS (100mM) tested. The observed delay in breakthrough curves of QDs was attributed to the fast diffusive mass transfer rate of QDs from bulk solution to the sand surface and QD mass transfer on the solid phase. Scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) analysis were used to examine the morphology and elemental composition of sand grains. It was observed that there were regions on the sand covered with layers of clay particles. EDX spectra collected from these regions revealed that Si and Al were the major elements suggesting that the clay particles were kaolinite. Additional batch experiments using gold NPs and SEM analysis were performed and it was observed that the gold NPs were only deposited on clay particles originally on the Accusand surface. After removing the clays from the sand surface, we observed negligible QD deposition even at 100mM IS. We proposed that nanoscale charge heterogeneities on clay particles on Accusand surface played a key role in QD deposition. It was shown that the value of solution IS determined the extent to which the local heterogeneities participated in particle deposition.     

Effect of amorphous silica and silica sand on removal of chromium(VI) by zero-valent iron

The effect of two surfaces (amorphous silica and silica sand) on the reduction of chromium(VI) by zero-valent iron (Fe(0)) was investigated using batch reactors. The amendment of both surfaces significantly increased the rate and extent of Cr(VI) removal. The rate enhancement by amended surfaces is presumed to result from scavenging of Fe(0)-Cr(VI) reaction products by the provided surfaces, which minimized surface deactivation of Fe(0). The rate enhancing effect was greater for silica compared to sand, and the difference is attributed to silica's higher surface area, greater affinity for reaction products and pH buffering effect. For a given mass of Fe(0), the reactivity and longevity of Fe(0) to treat Cr(VI) increased with increasing dose of silica. Elemental analyses of the reacted iron and silica revealed that chromium removed from the solution was associated with both surfaces, with its mass distribution being approximately 1:1 per mass of iron and silica. The overall result suggests reductive precipitation was a predominant Cr(VI) removal pathway, which involves initial reduction of Cr(VI) to Cr(III), followed by formation of Cr(III)/Fe(III) hydroxides precipitates.     

铁和铝氧化物涂层砂的过滤与吸附性能评价

总结性地对3种不同氧化物涂层砂和未涂层砂的表面特性、过滤和吸附性能进行了比较与分析,明确了适用范围。改性滤料的高温加热和碱性沉积两种制备方法中,涂铁宜选前者,涂铝宜用后者。涂层砂的比表面积增大,吸附容量增加,使石英砂表面电荷的带电性质改变,有利于水中杂质的去除。涂铁砂适合于除氟和除砷及除有机物;涂铝砂适合于除浊、除有机物和除锌。     

Aquifer washing by micellar solutions: 1: Optimization of alcohol–surfactant–solvent solutions

Phase diagrams were used for the formulation of alcohol–surfactant–solvent and to identify the DNAPL (Dense Non Aqueous Phase Liquid) extraction zones. Four potential extraction zones of Mercier DNAPL, a mixture of heavy aliphatics, aromatics and chlorinated hydrocarbons, were identified but only one microemulsion zone showed satisfactory DNAPL recovery in sand columns. More than 90 sand column experiments were performed and demonstrate that: (1) neither surfactant in water, alcohol–surfactant solutions, nor pure solvent can effectively recover Mercier DNAPL and that only alcohol–surfactant–solvent solutions are efficient; (2) adding salts to alcohol–surfactant or to alcohol–surfactant–solvent solutions does not have a beneficial effect on DNAPL recovery; (3) washing solution formulations are site specific and must be modified if the surface properties of the solids (mineralogy) change locally, or if the interfacial behavior of liquids (type of oil) changes; (4) high solvent concentrations in washing solutions increase DNAPL extraction but also increase their cost and decrease their density dramatically; (5) maximum DNAPL recovery is observed with alcohol–surfactant–solvent formulations which correspond to the maximum solubilization in Zone C of the phase diagram; (6) replacing part of surfactant SAS by the alcohol n-butanol increases washing solution efficiency and decreases the density and the cost of solutions; (7) replacing part of n-butanol by the nonionic surfactant HOES decreases DNAPL recovery and increases the cost of solutions; (8) toluene is a better solvent than D-limonene because it increases DNAPL recovery and decreases the cost of solutions; (9) optimal alcohol–surfactant–solvent solutions contain a mixture of solvents in a mass ratio of toluene to D-limonene of one or two. Injection of 1.5 pore volumes of the optimal washing solution of n-butanol–SAS–toluene–D-limonene in water can recover up to 95% of Mercier DNAPL in sand columns. In the first pore volume of the washing solution recovered in the sand column effluent, the DNAPL is in a water-in-oil microemulsion lighter than the excess aqueous phase (Winsor Type II system), which indicates that part of the DNAPL was mobilized. In the next pore volumes, DNAPL is dissolved in a oil-in-water microemulsion phase and is mobilized in an excess oil phase lighter than the microemulsion (Winsor Type I system). The main drawback of this oil extraction process is the high concentration of ingredients necessary for DNAPL dissolution, which makes the process expensive. Because mobilization of oil seems to occur at the washing solution front, an injection strategy must be developed if there is no impermeable limit at the aquifer base. DNAPL recovery in the field could be less than observed in sand columns because of a smaller sweep efficiency related to field sand heterogeneities. The role of each component in the extraction processes in sand column as well as the Winsor system type have to be better defined for modeling purposes. Injection strategies must be developed to recover ingredients of the washing solution that can remain in the soil at the end of the washing process. ©1997 Elsevier Science B.V.     

pH dependence of ferrous sorption onto two smectite clays

This work examines the abilities of two smectite minerals (SWa-1 and Wyoming montmorillonite) to adsorb ferrous iron at concentrations from 0.037 mM (2 ppm) to 2.5 mM (240 ppm) over a range of pHs from 4.0 to 8.0. Both sorption isotherm and sorption edge data are presented. Ferrous sorption (Fe(aq)2+ = 0.1 mM) to both SWa-1 and Wyoming montmorillonite over the pH range 4.0-6.75 is relatively constant at approximately 1000 l kg(-1) for both minerals. Sorption in this pH range is attributed to the cation exchange capacity of the clay along the basal surfaces. At pH values above 6.75 the amount of ferrous iron sorbed increases dramatically. At pH 8, sorption (Fe(aq)+ = 0.1 mM) reaches 6600 l kg(-1) and 8000 l kg(-1) for Swa-1 and Wyoming montmorillonite respectively. This is attributed to the specific interaction between ferrous ions and surface sites along mineral edges. The overriding geochemical implication is that in reduced sediments containing more than a few percent clay, the pool of sorbed ferrous iron is vast. This pool of reduced iron is both redox labile and bio-available and is not readily indicated by simple measurement of dissolved Fe2+.     

Migration of saline solutions in variably saturated porous media

Migration of concentrated NaNO3 solutions in homogeneous packs of pre-wetted silica sands was investigated using a light transmission system. Solutions of 5 molal NaNO3 were found to migrate downward 24-62% faster than pure water, in an unstable, fingered manner. This behavior was attributed primarily to a surface tension induced, non-zero apparent contact angle between the imbibing and the resident fluids. For saline solutions of similar surface tension to that of pure water (achieved by the addition of 2% methanol), the migration rates and plume shapes were comparable to that of water, demonstrating that density was not the primary source of the observed differences in migration patterns. At depths where resident saturation increased above residual, the migration process appeared to occur via film flow with slight changes in saturation (<4%), rather than in a series of abrupt jumps, as observed at shallower depths. A method for contact angle scaling was used to illustrate the effects of non-zero contact angles on capillary pressure-saturation curves.     

Mobilization and entry of DNAPL pools into finer sand media by cosolvents: two-dimensional chamber studies

Two-dimensional chamber studies were conducted to determine qualitative and quantitative performance of cosolvents targeted at pooled dense non-aqueous phase liquid (DNAPL) (perchlorethylene, PCE) residing above a fine-grain capillary barrier. Downward mobilization of DNAPL, up gradient along an overriding cosolvent front, was observed. This produced significant pooling above a fine-grain layer that in some cases lead to entry into the capillary barrier beneath. Entry pressure calculations using physical and hydrogeologic parameters provided an excellent prediction of breakthrough of DNAPL into the capillary barrier. Calculations predict approximately 0.5 m of DNAPL would be necessary to enter a Beit Netofa clay, under extreme cosolvent flooding conditions (100% ethanol). Gradient injection of cosolvent did not appear to provide any benefit suggesting a rapid decrease in interfacial tension (IFT) compared to the rate of DNAPL solubilization. Use of a partitioning alcohol (tertiary butyl alcohol, TBA) resulted in DNAPL swelling and reduced entry into the capillary barrier. However, the trapping of flushing solution, containing PCE, could potentially lead to longer remediation times.     

Bench-scale visualization of DNAPL remediation processes in analog heterogeneous aquifers: surfactant floods and in situ oxidation using permanganate

We have conducted well-controlled DNAPL remediation experiments within a 2-D, glass-walled, sand-filled chamber using surfactants (Aerosol MA and Tween 80) to increase solubility and an oxidant (permanganate) to chemically degrade the DNAPL. Initial conditions for each remediation experiment were created by injecting DNAPL as a point source at the top of the chamber and allowing the DNAPL to migrate downward through a water-filled, heterogeneous, sand-pack designed to be evocative of a fluvial depositional environment. This migration process resulted in the DNAPL residing as a series of descending pools. Lateral advection across the chamber was used to introduce the remedial fluids. Photographs and digital image analysis illustrate interactions between the introduced fluids and the DNAPL. In the surfactant experiments, we found that DNAPL configured in a series of pools was easily mobilized. Extreme reductions in DNAPL/water interfacial tension occurred when using the Aerosol MA surfactant, resulting in mobilization into low permeability regions and thus confounding the remediation process. More modest reductions in interfacial tension occurred when using the Tween 80 surfactant resulting in modest mobilization. In this experiment, capillary forces remained sufficient to exclude DNAPL migration into low permeability regions allowing the excellent solubilizing properties of the surfactant to recover almost 90% of the DNAPL within 8.6 pore volumes. Injection of a potassium permanganate solution resulted in precipitation of MnO2, a reaction product, creating a low-permeability rind surrounding the DNAPL pools. Formation of this rind hindered contact between the permanganate and the DNAPL, limiting the effectiveness of the remediation. From these experiments, we see the value of performing visualization experiments to evaluate the performance of proposed techniques for DNAPL remediation.