Polychlorinated biphenyls (PCBs) in indoor air originating from sealants in contaminated and uncontaminated apartments within the same housing estate

Twenty-four congeners of polychlorinated biphenyls (PCBs) were measured in 83 air samples and 20 elastic sealants samples of apartments with PCB-containing sealants. In addition, PCBs were measured in 21 air samples from reference apartments located in an uncontaminated section of the same estate. The PCB_tot levels in the air of the contaminated section were 168-3843 ng m⁻³ (mean: 1030 ng m⁻³), while the mean levels in the reference apartments were 6.03 ng m⁻³. The sum of the 24 measured PCB congeners in sealants from the contaminated section was 187-221 680 mg kg⁻¹. Principal component analysis revealed four groups among the sealant samples with different congener compositions, only two of which were clearly similar to known PCB mixtures, while two were not. Significant correlations and intercorrelations were observed between the lower chlorinated congeners in air and sealant, e.g. for PCB 28_air and 28_seal (p = 0.04) and for PCB 28_air and 52_air, 52_seal. However, no correlation was observed between the lower chlorinated congeners and the sums of PCB (∑PCB₆ or ∑PCB₂₄) or the higher chlorinated congeners. Analysis of air concentrations in relation to questionnaire data indicated that the indoor air levels could be reduced by increased cleaning and airing frequencies.     

Distribution patterns of nitrobenzenes and polychlorinated biphenyls in water, suspended particulate matter and sediment from mid- and down-stream of the Yellow River (China)

Samples of water, suspended particulate matter (SPM) and sediment were collected from mid- and down-stream of the Yellow River. The distribution and concentration of 10 nitroaromatic compounds and polychlorinated biphenyls (PCBs) were extensively studied. The total concentration of 10 nitrobenzenes (SigmaNBs) varied from 0.269 to 9.052 microg l(-1) in water, from 2.916 to 164.4 microg kg(-1) dry weight in SPM, and from 0.954 to 14.72 microg kg(-1) dry weight in sediment. PCBs associated with the sediments, measured as the summed responses of Aroclor 1242, 1248, 1254, 1260 (in comparison to those of a standard 1:1:1:1 mixture), were found to be in the range of non-detectable to 5.98 microg kg(-1). In the samples collected, various PCB congeners showed similar distribution characteristics with congeners containing 3-5 chlorine atoms accounting for more than 96.4% of total PCB. In most of the samples, PCB concentrations occurred in the order: TetraCB > TriCB > PentaCB. Levels of SigmaNBs in the Yellow River were relatively low in comparison with values reported from other river and marine systems, and PCB levels were comparatively low. Relative to the PCBs, SigmaNBs showed significantly more difference among the various stations, presumably due to the influence of different pollution sources. No obvious correlation was observed between the pollutant concentrations and either the TOC or the grain size of the sediments.     

Congener profiles of PCB and a proposed new set of indicator congeners

In this study, a new method for calculating total PCB and toxic equivalents (TEQ) of coplanar PCB (Co-PCB) was proposed, called the 'PCB dual method'. This method analysed various kinds of technical PCB, samples contaminated by technical PCB and byproduct PCB. In the PCB dual method, a data set of 15 indicator congeners was utilized for the calculations, having IUPAC nos. #3, #8, #28, #52, #77, #101, #105, #118, #126, #138, #153, #180, #194, #206 and #209. The 15 congener set was chosen from the major congeners, determined by HRGC/HRMS analysis, in 18 technical PCB, Kanechlor, Aroclor, Clophen and Chlorofen, and 20 other samples, such as indoor air, flue gases, emission gases, municipal solid waste (MSW), ash and sealant. To obtain total PCB and TEQ of Co-PCB, the intermediate sum for the concentration of the 15 congeners was multiplied by each multiplication factor. As a result, we obtained the average factor used to calculate total PCB in technical PCB and other samples. For technical PCB, the factor was 3.01, while for indoor air samples, flue and emission gases, MSW, ash and sealants, the factors were 3.92, 4.16, 3.68, 4.52 and 4.77, respectively. Moreover, the factor used to calculate the TEQ of Co-PCB in Kanechlor and other source samples were also obtained. The factors for Kanechlor, indoor air samples and emission gases from a cement plant were in the order of 10(-5), while the factor for flue gases in a MSW incinerator was in the order of 10(-3). These data were valuable for the rough estimation of the TEQ of Co-PCB without separation from other PCB before individual measurements.     

Airborne PCB as a contamination risk on freeze-drying of sediment

In a study of polychlorinated biphenyls (PCB) in freeze-dried sediments from Swedish lakes, the samples were found to contain unexpectedly high concentrations of PCBs. In one of the lakes (Bj?rken), e.g. the concentration of PCB-28 was found to be 189 ng/g dw after freeze-drying compared to 7 ng/g dw after air-drying of the sediment and therefore our hypothesis was that the contamination had occurred during the freeze-drying procedure. Hence, a dry reference sediment (RS) was used in order to identify potential sources of PCB contamination. The investigation included freeze-drying of the dry RS in five different laboratories, exposure to the air in the freeze-drying room, storage at room temperature and air-drying in a certain fume hood and in a laminar flow clean bench. The pattern and concentrations of PCBs detected in the exposed RS were strongly influenced by low chlorinated PCB congeners under all of these conditions with exception for air-drying in the fume hood. Storage in the laboratory air resulted in a slight elevation in the concentrations of low chlorinated PCB congeners, whereas higher concentrations of all PCB congeners were observed after freeze-drying. In all experiments the contamination appeared to be due to adsorption of PCB from the laboratory air. On the basis of these findings we recommend that reference material be subjected to the entire procedure, including sample preparation, in order to monitor contamination and that a procedure involving solvent extraction of wet sediment samples is used, whenever possible, instead of procedures involving dry samples.     

Correlation of PCDD/F and PCB concentrations in soil samples from the Swiss soil monitoring network (NABO) to specific parameters of the observation sites

Concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) and polychlorinated biphenyls (PCB) were determined in 23 soil samples collected at reference sites of the Swiss national soil monitoring network (NABO). Total PCDD/F and PCB concentrations are well correlated and proportional (R2=0.720). The total PCDD/F levels were between 72 and 703 ng/kg corresponding to 1.1-11 ng I-TEQ/kg, total PCB concentrations (sum of seven congeners IUPAC no. 28, 52, 101, 118, 138, 153, and 180) were from 1.1 to 12 microg/kg. In all samples, the PCDD/F and PCB concentrations were in the range of background levels for these contaminants in Central Europe. Ninteen samples revealed PCDD/F levels below the guide value of 5 ng I-TEQ/kg set by the Swiss ordinance relating to impacts on the soil (OIS); concentrations for the remaining four samples were below the trigger value (20 ng I-TEQ/kg). All PCB concentrations were below the guide value of 100 microg/kg. The elevated PCDD/F and PCB levels in some of the samples originating from forested sites could be attributed to the scavenging effect of forest canopies for semivolatile organic compounds. This interpretation could be substantiated by the observed distortion of the congener and homolog patterns of PCDD/F and PCB which is characteristic for forested sites.     

Delineating landfill leachate discharge to an arsenic contaminated waterway

Discharge of contaminated ground water may serve as a primary and on-going source of contamination to surface water. A field investigation was conducted at a Superfund site in Massachusetts, USA to define the locus of contaminant flux and support source identification for arsenic contamination in a pond abutting a closed landfill. Subsurface hydrology and ground-water chemistry were evaluated in the aquifer between the landfill and the pond during the period 2005-2009 employing a network of wells to delineate the spatial and temporal variability in subsurface conditions. These observations were compared with concurrent measures of ground-water seepage and surface water chemistry within a shallow cove that had a historical visual record of hydrous ferric oxide precipitation along with elevated arsenic concentrations in shallow sediments. Barium, presumably derived from materials disposed in the landfill, served as an indicator of leachate-impacted ground water discharging into the cove. Evaluation of the spatial distributions of seepage flux and the concentrations of barium, calcium, and ammonium-nitrogen indicated that the identified plume primarily discharged into the central portion of the cove. Comparison of the spatial distribution of chemical signatures at depth within the water column demonstrated that direct discharge of leachate-impacted ground water was the source of highest arsenic concentrations observed within the cove. These observations demonstrate that restoration of the impacted surface water body will necessitate control of leachate-impacted ground water that continues to discharge into the cove.     

Analysis of some polyhalogenated organic pollutants in sediment and sewage sludge

A laminated sediment core collected in the southern part of the Baltic Proper was analysed for DDT compounds, polychlorinated biphenyls (PCB) including the coplanar congeners, polybrominated diphenyl ethers (PBDE) and polychlorinated naphthalenes (PCN). Two sewage sludge samples were also analysed for the same compounds.

The results of the sediment analyses indicate the presence of PCB, DDT and PBDE compounds in sediment layers dating from the 1950s and later. Neither coplanar PCB nor PCN were detected at any level of the sediment core. The PCB concentrations indicate a slight increase in levels during the last decades, while there were no changes in the levels of DDT compounds. In contrast, TeBDE levels increase 4- to 8-fold and one PeBDE congeners levels increase 10- to 20-fold. The results of sewage sludge analyses showed the concentration of the individual PBDE to be at about the same level as for the individual PCB congeners. The congener pattern in sludge samples indicates low-chlorinated products to be the main PCN source.     

Levels and congener pattern of PCBs in arctic fox, Alopex lagopus, in Svalbard

Levels and congener pattern of polychlorinated biphenyls (PCBs) were determined in samples of subcutaneous fat and liver from 27 polar foxes, Alopex lagopus, caught in Svalbard during the winter 1983-1984. In all the samples analysed the composition of individual PCB congeners was studied by comparison with 12 individual PCB congeners (IUPAC nos. 28, 52, 101, 118, 138, 153, 170, 180, 183, 194, 206 and 209). In addition, the PCB congeners nos. 99, 105, 114, 156 and 157 were determined in the fat samples. In both liver and fat samples the sum PCB was calculated based on the concentrations of seven selected congeners, nos. 138, 153, 170, 180, 194, 206 and 209. These congeners were the same as those used in a corresponding investigation made on arctic fox from Svalbard 10 years earlier. The present study reveals that the PCB levels in arctic fox in Svalbard are high and essentially unchanged in the period from 1973-1974 to 1983-1984. The mean sum PCB levels in fat and liver were 8.3 +/- 11 and 0.4 +/- 0.4 microg g(-1), and the extractable fat was 81.2 +/- 8.4 and 4.5 +/- 1.7% for the two tissues, respectively. In fat, sum PCB ranged from 0.5 to 41.0 microg g(-1). PCB nos. 153 and 180 accounted for approximately 65% of sum PCB. The contributions of PCB nos. 138 and 153 to the sum PCB were found to increase from 1974 to 1984. The PCB congener pattern is similar to that found in polar bears, and is dominated by a few congeners (99, 138, 153, 170, 180 and 194). No significant differences in PCB levels were found between sexes or between age groups. However, significantly higher PCB levels were found in old animals (>/= 3 years) with less than 2 cm of fat on the ramp as compared with young animals (1-2 years) with more than 2 cm of fat on the rump. Effects on vital functions from the observed levels of PCBs cannot be excluded for the most contaminated foxes.     

Levels of selected individual polychlorinated biphenyls in different tissues of harbour seals (phoca vitulina) from the Southern coast of Norway

Concentrations of individual polychlorinated biphenyls (PCBs) were determined in blubber, liver, kidney and brain tissues of 10 male harbour seals (Phoca vitulina) of different ages. The animals were found dead or dying on the southern coast of Norway in 1988 during the morbilli virus epizootic. Twenty-three PCB congeners were investigated in all tissues by capillary gas chromatography with electron capture detection and comparison with standards of the respective congeners (IUPAC numbers 28, 52, 74, 99, 101, 105, 110, 114, 118, 128, 138, 141, 149, 153, 156, 157, 170, 180, 183, 187, 194, 206 and 209). In addition, three toxic coplanar congeners (IUPAC numbers 77, 126 and 169) were investigated in the blubber samples. Total PCB (sum of the determined congeners) in kidney (12-60 nmol g(-1)), liver (12-90 nmol g(-1)) and blubber (10-79 nmol g(-1)) were similar on extractable lipid basis, while total PCB in brain lipid was about 1/10 (1.6-12 nmol g(-1)). The absolute concentrations of the individual congeners in brain lipid correlated poorly with the respective concentrations in each of the other tissues, while the individual congener concentrations in the lipid fractions of kidney, liver and blubber tended to correlate with each other. The relative concentrations of the sum of the most persistent congeners (PCB-99, -128, -138, -153, -170, -180, -187 and -194) correlated in all tissues, and an increase of the relative concentrations of these congeners, most distinct in blubber, with higher carcass weight, was shown. Also, total PCB in blubber correlated with carcass weight. When comparing the relative concentration patterns of individual congeners (per cent of total) in the four tissues, six congeners differed significantly between tissues, and the relative brain concentrations showed most deviation from the other tissues. The concentration of the coplanar PCBs was 1 : 1000-1 : 1000 of the total PCB concentration. The results demonstrate a lower accumulation together with a different concentration pattern in the brain as compared to other tissues.     

Solid phase extraction with pyrenebutyric acid-bonded silica for analysis of polychlorinated biphenyls in sewage water by gas chromatography-mass spectrometry

A solid phase extraction (SPE) method using pyrenebutyric acid-bonded silica (PYB) as sorbent was developed to determine 23 polychlorinated biphenyls (PCBs) in sewage water by gas chromatography-mass spectrometry (GC-MS). Factors were optimized in SPE procedures including elution solvent, pH, and cartridge burden. The recoveries of 23 PCB congeners were 69.44-111.91% under optimized conditions. Comparisons were also conducted among PYB-SPE, C(18)-SPE and United States Environmental Protection Agency 608 (USEPA608) methods in the analysis of PCBs in sewage water samples. The results showed that the performance of PYB-SPE method was similar with USEPA608 method and better than C(18)-SPE method. Both PYB-SPE and USEPA608 methods were then employed to analyze PCBs in real spiked sewage water samples. The recoveries of PCB congeners determined by PYB-SPE method ranged from 70.6% to 92.4% in real spiked sewage water samples which were identified to be in accordance with USEPA608 method. Limits of detection (LOD) were in the range of 0.06-0.22ngL(-1) for PCB congeners. The optimized PYB-SPE method was successfully applied to the determination of PCBs in sewage water samples.     

Assessment of polychlorobiphenyls in human/poultry fat and in hair/plumage from a contaminated area

HR gas chromatographic PCB patterns in human/poultry fat tissue and hair/plumage in samples from a polluted region of Bela Krajina /Slovenia/ were investigated. The concentration of PCBs in human adipose tissue was found to be 9.62 μg/g in comparison to 0.67 μg/g in the adipose tissue of the non-exposed population, and in poultry fat 12.80 μg/g on a fat basis. The corresponding values in human hair and poultry plumage were 0.90 μg/g and 0.20 μg/g of original weight. The difference in PCB patterns between fat and hair can be attributed to the different routes of contamination (ingestion, air transport), to the time of exposure and physicochemical properties (octanol- water partition coefficients, Henry's law constants and the metabolism) of some individual congeners. Hair could be used for the assessment of ingestion of contaminated food and of the PCB levels in the air. In fat tissue PCB congeners with higher metabolic stability are enriched, whereas in hair PCB congeners with higher concentrations in air and with high octanol- water partition coefficients predominate.     

Persistent organochlorines in beluga whales (Delphinapterus leucas) from the St Lawrence River estuary--I. Concentrations and patterns of specific PCBs, chlorinated pesticides and polychlorinated dibenzo-p-dioxins and dibenzofurans

Blubber samples from beluga whales (Delphinapterus leucas) in the St Lawrence River estuary were analysed for PCB congeners (ortho- and non-ortho-substituted) and other persistent organochlorines as well as chlorinated dibenzo-dioxins/furans (PCDD/Fs). Major individual components (mean concentrations > 1 microg g(-1)) were 4,4'-DDE, -DDD and -DDT, T12 (a toxaphene-related compound), trans-nonachlor, oxychlordane, mirex, HCB, tris(p-chlorophenyl) methane and dieldrin. Concentrations of SigmaPCBs (8.3-412 microg g(-1)), SigmaDDT (3.36-389 microg g(-1)) and mirex (0.18-6.8 microg g(-1)) were particularly elevated relative to other odontocetes in Canadian waters. SigmaDDT, PCBs (as Aroclor), mirex and T12 concentrations were positively correlated with age of adult females (> 10 years) but only weakly, or not significantly, correlated with age of adult males. PCDD/Fs were present at low ng kg(-1) levels and consisted mainly of penta- and hexachlorofurans, and hepta- and octachlorodioxin. CB126 (3,3',4,4',5-PCB) was the most prominent non-ortho-substituted PCB congener in beluga blubber. Total TCDD toxic equivalents averaged 330 ng kg(-1) in females and 1400 ng kg(-1) in males and were dominated by CB126, and the mono-ortho-substituted congeners CB105 and CB118. Biomagnification factors (BMFs) for mirex and SigmaPCB from fish to beluga ranged from 11 to 16, and were similar to BMFs in Arctic animals, indicating that elevated levels in St Lawrence animals are a consequence of relatively high levels of recalcitrant organochlorines in prey of the beluga in the St Lawrence river system.     

PCB and dioxin-like PCB in indoor air of public buildings contaminated with different PCB sources--deriving toxicity equivalent concentrations from standard PCB congeners

Data on dioxin-like PCB in indoor air of buildings with PCB-containing materials and on possible correlation between toxicity equivalent concentrations (TEQ) and levels of non-dioxin-like standard PCB is sparse. As part of a larger survey on indoor-air contamination with PCB, the connection between the concentration of standard PCB congeners and the dioxin-like toxicity expressed as TEQ was investigated. Indoor air samples (n=8) were collected in four public buildings with known PCB sources and total PCB levels in the range from 715 to 2250 ng/m3 and analyzed for the six non-dioxin-like standard PCB (congeners 28, 52, 101, 138, 153, 180), the twelve dioxin-like PCB congeners according to WHO and the 17 2,3,7,8-substituted PCDD/PCDF congeners. In three buildings where PCB were used as flame retardant coatings of acoustic ceiling tiles, PCB 101 had the maximum level among the six standard PCB, while in the building with permanent elastic sealants as PCB source, congeners 28 and 52 dominated the pattern by far. In the case of permanent elastic sealants as PCB source (n=3) a total PCB concentration of 1000 ng/m3 corresponded to a total TEQ level of 0.3-0.6 pg/m3. In contrast, in rooms with acoustic ceiling tiles as PCB source, 1.8-4.7 pg TEQ/m3 per 1000 ng total PCB/m3 were found. Linear regression analysis between PCB and TEQ indicated that PCB 118 might be used to calculate the total TEQ of dioxin-like PCB and PCDD/PCDF. By means of such a correlation it is possible to estimate TEQ by extrapolation from the results of less sophisticated analytical methods. It is tentatively recommended to use PCB 118 for screening purposes or re-evaluation of standard PCB indoor-air measurements. If only the six non-dioxin-like PCB standard congeners are available, a regression algorithm using the sum of PCB 101, 138, 153 and 180 might be used instead.     

Human biomonitoring of polychlorinated biphenyls and polychlorinated dibenzodioxins and dibenzofuranes in teachers working in a PCB-contaminated school

Eighteen teachers from a highly contaminated school and 11 teachers from a control school participated in this study. Total polychlorinated biphenyl (PCB) indoor air concentration (six indicator congeners x 5) was beyond 12000 ng/m3 in some rooms of the contaminated school. PCB 28 and PCB 52 were the prevailing congeners. Whole blood was taken from each participant by the local health authority, pooled in two groups and analysed for the six PCB indicator congeners, non-ortho PCBs and polychlorinated dibenzodioxins (PCDD)/polychlorinated dibenzofurans (PCDF). Blood analysis showed elevated mean PCB 28 and PCB 52 levels for the exposed group, however the two groups were almost identical with regard to PCB 101, 138, 153 and 180. Moreover no difference can be observed for the concentration of non-ortho PCBs and PCDD/PCDF. The data support the finding, that heavy indoor air contamination with low chlorinated PCBs causes an increase of PCB 28 and PCB 52 blood levels. However, this increment was small compared to their total PCB load.     

Levels,distribution profile,and risk assessment of polychlorinated biphenyls (PCBs) in water and sediment from two tributaries of the River Chenab,Pakistan

The first study aimed to investigate the polychlorinated biphenyl (PCB) concentration level, spatial distribution pattern, and ecological risk assessment of water and sediment samples from two tributaries (Nullah Aik and Palkhu) of the River Chenab, Punjab Province, Pakistan. A total of 32 PCB congeners were analyzed, and PCB concentration in sediment and water samples ranged between 0.80 and 60 ng/g and 0.20 and 28 ng/L, respectively, where tetra-CBs and tri-CBs dominated over other studied PCB homologs. Dioxin toxicity equivalency (TEQ) was calculated and PCB-126 and PCB-169 showed the higher TEQ values compared with the WHO guidelines, and sediment samples were more toxic than the water samples. The results of the present study should be considered seriously by government authorities to take a proper action against unchecked discharge of contaminants in ecological integrities; otherwise, there may be drastic results in the near future.     

Why biota still accumulate high levels of PCB after removal of PCB contaminated sediments in a Norwegian fjord

Accumulation of polychlorinated biphenyls (PCBs) in blue mussels (Mytilus edulis) and semipermeable membrane devices (SPMDs) was still high after the removal of PCB contaminated sediments from a Norwegian fjord by dredging. The accumulation of low chlorinated PCB congeners with a low octanol water-partitioning coefficient (K_ow) in blue mussels and SPMDs was higher than for the highly chlorinated congeners with a high K_ow. The accumulation of low chlorinated congeners was also higher in a lightly contaminated area compared to a highly contaminated area. That dredging the contaminated sediments was unsuccessful in lowering PCB levels in the biota may be for the following reasons: (1) Due to the low solubility of PCBs in the water it is possible that a decrease in the sediment concentration of PCB would leave the water concentrations of PCB unchanged. (2) Removal of the fine organic sediments may also play an important role, since a seabed with coarse inorganic material has a lesser ability to bind PCB. (3) The dredging may whirl up fine contaminated particles that eventually settles on the seabed producing a thin contaminated sediment layer that determine the water concentration. (4) Bioaccumulation in blue mussels and in the SPMDs occurs mostly from PCB dissolved in the water column. Since the water concentration of PCB is unchanged by the dredging, the accumulation in SPMDs and mussels is the same as before dredging. Further monitoring need to be carried out to report the long-term effect of the dredging.     

Historical trends of PCDD/Fs and dioxin-like PCBs in sediments buried in a reservoir in Northern Taiwan

Polychlorinated dibenzo-p-dioxin (PCDD), polychlorinated dibenzofuran (PCDF) and polychlorinated biphenyl (PCB) concentrations were analyzed at 1-2cm intervals in a sediment core collected from a reservoir in Northern Taiwan to evaluate the organic pollution history. The highest PCDD/F (14.4ng TEQ/kg d.w.) and PCB (0.261ng TEQ(WHO)/kg d.w.) concentrations were determined at 13-15cm (estimated year: 1992). The ages of the levels of sediment core were estimated from the sedimentation rate. Analysis results demonstrate that the PCDD/F concentration of the sediment core measured in the reservoir reached their peak when the municipal waste incinerators (MWIs) in the area started to operate. Furthermore, the decrease in sediment core PCDD/F concentration is related to the time of enforcement of the PCDD/F emission limit set by the Environmental Protection Administration (EPA) in Taiwan. Significant distribution of OCDD in homologue profiles was noted in archived soil samples in Taiwan in which the major input of PCDD/Fs was thought to be atmospheric. Major PCB congeners found in the sediment core were the major components of the commercial PCB products. Input fluxes of PCDD/Fs (5.75-158ng-I-TEQ/m(2)-yr) and PCBs (0.248-3.71ng TEQ(WHO)/m(2)yr) into the reservoir of interest are also calculated from the concentration and sedimentation rate of the sediment. The results reveal that considerable amounts of PCDD/Fs and PCBs were carried into the reservoir of interest in the flood stage but not during normal stage.     

Detailed PCB congener patterns in incinerator flue gas and commercial PCB formulations (Kanechlor)

In this study, we determined the detailed PCB congener patterns in flue gases from eight incinerators and four commercial PCB formulations (Kanechlors). About 160 PCB peaks were identified in samples using a DB-5 column and HRGC/HRMS. The concentration of incinerator stack emission gas ranged from 0.02 to 44 ngWHO-TEQ/Nm3. The ratios of dioxin-like PCBs in the total PCB concentration were from 3.4% to 25.7% and from 0.63% to 9.1% in stack emission gases and Kanechlor samples, respectively. The PCB congener profiles of Kanechlor samples were similar to those of previous studies. To determine characteristic congeners in flue gas and Kanechlor samples, principal component analysis (PCA) of the data was conducted using STATISTICA for Windows 5.0J (StatSoft, Inc.). As a result, we obtained four principal components (PCs) and accounted for 74% of the total variance. PC 1 was interpreted combustion, PC 2 and PC 3 were interpreted the difference in the number of substituted chlorines and, PC 4 could not be determined. Moreover, we obtained three groups according to the PCB congeners pattern among samples by PCA. These specific congeners that represent characteristics of each class were identified. These data will be useful for the source analysis of PCBs in the environment.     

Non-controlled biogenic emissions to the atmosphere from Lazareto landfill, Tenerife, Canary Islands

GOAL, SCOPE AND BACKGROUND: [corrected] Historically, landfills have been the simplest form of eliminating urban solid waste with the minimum cost. They have been the most usual method for discarding solid waste. However, landfills are considered authentic biochemical reactors that introduce large amounts of contaminants into the environment in the form of gas and leachates. The dynamics of generation and the movement of gas in landfills depend on the input and output parameters, as well as on the structure of the landfill and the kind of waste. The input parameters include water introduced through natural or artificial processes, the characteristics of the urban solid waste, and the input of atmospheric air. The main output parameters for these biochemical reactors include the gases and the leachates that are potentially pollutants for the environment. Control systems are designed and installed to minimize the impact on the environment. However, these systems are not perfect and a significant amount of landfill gas could be released to the atmosphere through the surface in a diffuse form, also known as Non-controlled emission. In this paper, the results of the Non-controlled biogenic gas emissions from the Lazareto landfill in Tenerife, Canary Islands, are presented. The purpose of this study was to evaluate the concentration of CH4 and CO2 in the soil gas of the landfill cover, the CH4 and CO2 efflux from the surface of the landfill and, finally, to compare these parameters with other similar landfills. In this way, a better understanding of the process that controls biogenic gas emissions in landfills is expected. METHODS: A Non-controlled biogenic gas emission survey of 281 sampling sites was carried out during February and March, 2002. The sampling sites were selected in order to obtain a well-distributed sampling grid. Surface landfill CO2 efflux measurements were carried out at each sampling site on the surface landfill together with soil gas collection and ground temperatures at a depth of 30-40 cm.The CH4 efflux was computed from CO2 efflux and from the ratio CH4/CO2 in the soil gas. Soil gas samples were collected at a depth of 30-40 cm using a metallic probe and 20 cc hypodermic syringes, and later stored in evacuated 10 cc vacutainers for laboratory analysis of bulk composition. The gas sample was introduced in a vacutainer filled with deionized water and displacing the water until the vacutainer was filled with the gas sample in order to avoid air contamination from entering. The surface landfill temperature of the landfill was measured at a depth of 40 cm using a digital thermometer type OMEGA 871A. Landfill gases, CO2 and CH4, were analyzed within 24 hours using a double channel VARIAN micro-GC QUAD CP-2002P, with a 10 meter PORAPLOT-Q column, a TCD detector, and He as a carrier gas. The analysis temperature was 40 degrees C and the injection time was 10 msec. Surface landfill CO2 efflux measurements were performed using a portable NDIR spectrophotometer Licor-800 according to the accumulation chamber method (Chiodini et al. 1996). The data treatment, aimed at drawing the flux map and computing the total gas output, was based on the application of stochastic simulation algorithms provided by the GSLIB program (Deutsch and Journel 1998). RESULTS: Diffuse CH4 and CO2 efflux values range from negligible values up to 7,148 and 30,573 g m(-2) d(-1), respectively. The spatial distribution of the concentration and efflux of CO2, CH4 and soil temperature, show three areas of maximum activity in the landfill, suggesting a non-uniform pattern of diffuse degassing. This correlation between high emissions and concentration of CO2, CH4 and soil temperatures suggests that the areas of higher microbial activity and exothermic reactions are releasing CO2 and CH4 to the atmosphere from the landfill. Taking into consideration the spatial distribution of the CO2 and CH4 efflux values as well as the extension of the landfill, the Non-controlled emission of CO2 and CH4 to the atmosphere by the Lazareto's landfill are of 167 +/- 13.3 and 16 +/- 2.5 t d(-1), respectively. DISCUSSION: The patterns of gas flow within the landfill seem to be affected by boundary materials at the sides. The basalt layers have a low permeability and the gas flow in these areas is extensive. In this area, where a basalt layer does not exist, the flow gas diffuses toward the sea and the flux emissions at the landfill surface are lower. This behavior reflects the possible dissolution of gases into water and the deflection of gases towards the surface at the basalt boundary. The proximity to the sea, the installation of a palm tree garden and, as a result, the contribution of water coming from the watering of this garden has reactivated the system. The introduction of sea water into the landfill and the type of boundary could be defining the superficial gas discharges. CONCLUSIONS: Results from this study indicate that the spatial distribution of Non-controlled emission of CO2 and CH4 at the Lazareto's landfill shows a non-uniform pattern of diffuse degassing. The northeast, central and northwest areas of the Lazareto's landfill are the three areas of high emissions and concentration of CO2 and CH4, and high temperatures. The correlation between high emissions and the concentration of CO2, CH4, and the high temperatures suggest that the areas of higher microbial activity and exothermic reactions are releasing more CO2 and CH4 to the atmosphere from the landfill. A high concentration of CO2 is probably due to the presence of methanotrophic bacteria in the soil atmosphere of the landfill. Patterns of gas flow within the landfill seem to be affected by boundary materials (basalt layers) of low permeability, and side boundaries of the flux emissions at the surface are higher. At the sides of seawater and sediment boundaries, flux emissions at the landfill surface are lower. This behavior reflects a possible dissolution of gases into the water and the deflection of gases towards the surface at the basalt boundary. With this study, we can compare the data obtained in this landfill with other landfills and observe the different levels of emission. The proximity to the sea and the installation of the palm tree garden palms and, as a result, the contribution of water coming from the watering of this garden has reactivated the system. Many landfills worldwide located in similar settings could experience similar gas production processes. RECOMMENDATIONS AND PERSPECTIVES: The need for investigating and monitoring sea water and sediment quality in these landfills is advisable. Concentrations and fluxes of contaminants and their impact in the area should be assessed. With this study we can compare the data obtained in these landfills with other landfills and observe the different levels of emission.