Adsorption of methabenzthiazuron on six allophanic and nonallophanic soils: effect of organic matter amendment

This article reports on methabenzthiazuron [1-(1,3-benzothiazol-2-yl)-1,3-dimethylurea] (MBT) adsorption process on six agricultural allophanic and nonallophanic soils. The effect of amendment with exogenous organic matter was also studied. Adsorption kinetic fits an hyperbolic model. MBT adsorption reached an apparent equilibrium within 2 h and followed a second-order reaction. The maximum adsorbed amounts for natural soils ranged from 32 to 145 microg g(-1). Rate constants were considered relatively low (0.27-1.5 x 10(-4) [microg g(-1)](1-n) s-1); the slow process was attributed to a combined effect of difussion and adsorption. MBT adsorption fits the Freundlich model with r values > or =0.998 at P < or = 0.001 significance levels. Kf and Freundlich exponents (l/n) ranged from 5.3 to 82.1 cm3 g(-1) and from 0.66 to 0.73, respectively. Kf values for soils with a low organic matter content were lower than that obtained from the only typical allophanic soil derived from volcanic ash under study. Lineal regression analysis between Kf and organic matter content of nonallophanic soils gave a correlation coefficient of 0.980 (P = 0.02). Dispersion of Kd values together with close values of K(OM) indicate that organic matter (OM) was the principal component responsible for MBT adsorption in unamended soils. Addition of peat decreased soil pH and increased adsorption capacity for allophanic and nonallophanic soils. Kinetic experiments showed enhancements of Xmax values and lower rate constants.     

The mechanism of chromate sorption by three variable charge soils

Adsorption of chromate and desorption of the pre-adsorbed chromate were studied using three representative variable charge soils from the south of China. The mechanisms of the adsorption were discussed based on the hydroxyl release and the change of zeta potential during the chromate adsorption. The adsorption and desorption of chromate followed the same order: the Hyper-Rhodic Ferralsol>the Rhodic Ferralsol>the Haplic Acrisol. The adsorption and the desorption both increased with elevation of the equilibrium chromate concentration and decreased with increasing of the soil solution pH. The percentage of the specific adsorption of chromate was 54.0-59.4%, 54.3-60.3%, and 43.9-46.2% for the Hyper-Rhodic Ferralsol, the Rhodic Ferralsol, and the Haplic Acrisol, respectively; the percentage of the electrostatic adsorption was 40.0-46.6%, 39.7-45.8%, and 50.8-56.5% for the three soils, respectively. These findings suggest that both the specific adsorption and the electrostatic adsorption contributed to the chromate adsorption by the variable charge soils. The hydroxyl release during the chromate adsorption shared the same trend with the adsorption envelopes, and decreased with increasing of pH. This is attributed to the exchange of chromate with the hydroxyl on the soil particle surfaces and the formation of a chemical bond between chromate and the surface. Our results indicate that the adsorption of chromate resulted in a shift of zeta potential-pH curves of the soil colloids to negative values, which suggests that the adsorption increased the negative surface charge and decreased the surface potential of the soil colloids.     

Effects of several low-molecular weight organic acids and phosphate on the adsorption of acid phosphatase by soil colloids and minerals

Adsorption of acid phosphatase on goethite, kaolinite and two colloids from the soils in central and south China in the presence of organic acids and phosphate was studied. With the increase of anion concentration, the ability in decreasing enzyme adsorption followed the sequence: phosphate>tartrate>oxalate>acetate. Acetate showed promotive effect on enzyme adsorption at lower anion concentrations whereas oxalate, tartrate and phosphate compete effectively with enzyme in a broad range of anion concentration. The adsorption isotherms of enzyme in most of the anionic systems studied conformed to the Langmuir equation. Phosphate reduced the affinity of enzyme on goethite more significantly than the other anions. However, tartrate decreased the affinity of enzyme on soil colloids and kaolinite to a greater extent than phosphate, oxalate and acetate. This observation suggested that the impact of anions on enzyme adsorption varies with anionic type and the surface characteristics of soil components. The influence of the addition order of ligand on enzyme adsorption was found greater in tartrate and phosphate systems. In general, simultaneous introduction of ligand and enzyme into the system had the lowest enzyme adsorption, showing more competition between ligand and enzyme molecules in this system. Data from this work indicated that the status and activity of enzyme in certain soil microenvironments especially the rhizosphere where various organic and inorganic ligands are active can be altered and may be completely different from the bulk soil.     

Adsorption and desorption characteristics of hydrophobic pesticide endosulfan in four Indian soils

Adsorption and desorption characteristics of endosulfan in four Indian soils were studied extensively. The soils used were clayey soil (CL--lean clay with sand), red soil (GM--silty gravel with sand), sandy soil (SM--silty sand with gravel) and composted soil (PT--peat) as per ASTM (American Society for Testing and Materials) standards. Adsorption and desorption rates were calculated from kinetic studies. These values varied for alpha and beta endosulfan depending on the soil type. Maximum specific adsorption capacities (qmax) for different soils were calculated by Langmuir model. The values varied from 0.1 to 0.45 mg g(-1) for alpha endosulfan and 0.0942-0.2722 mg g(-1) for beta endosulfan. Maximum adsorption took place in clay soil followed by composted soil and red soil. Adsorptions of alpha and beta endosulfan were negligible in sand. The binding characteristics of various functional groups were calculated using Scatchard plot. Effect of functional groups was more predominant in clayey soil. Organic matter also played a significant role in adsorption and desorption of endosulfan. Endosulfan adsorption decreased drastically in clay soil when the pH was reduced. Desorption was higher at both acidic and alkaline pH ranges compared to neutral pH. Results indicated that alpha endosulfan is more mobile compared to beta endosulfan and mobility of endosulfan is maximum in sandy soil followed by red soil. It can be inferred that crystal lattice of the clay soil plays a significant role in endosulfan adsorption and desorption. Immobilization of endosulfan is more advisable in clay soil whereas biological and or chemical process can be applied effectively for the remediation of other soil types.     

A comparative study of adsorption of an anionic and a non-ionic surfactant by soils based on physicochemical and mineralogical properties of soils

In the present work we performed a comparative study on the adsorption of the surfactants sodium dodecyl sulphate (SDS) (anionic), and octylphenoxypolyethoxyethanol (Triton X-100) (non-ionic) to 18 soils with organic matter (OM) and clay fraction contents varying over a broad range. The objective of the study was to gain further insight into the influence of the physicochemical and mineralogical properties of soils on the adsorption of surfactants by soils. Adsorption isotherms were obtained using concentrations below the critical micellar concentration (cmc) of the surfactants. The adsorption coefficients, Kf, determined from the Freundlich equation were lower for SDS (range 1.77-82.1, mean value 36.3) than for Triton X-100 (range 0.01-913, mean value 257). Simple and multiple correlation coefficients were obtained between Kf values and soil characteristics. The results obtained indicate the influence of the OM content on the adsorption of SDS (r=0.64, p<0.01) and of the clay fraction content on that of Triton X-100 (r=0.83, p<0.001). Additionally, we observed a preferential adsorption of SDS by the 1:1 mineral kaolinite (r=0.54, p<0.05), while Triton X-100 was adsorbed mainly by the 2:1 minerals, montmorillonite (r=0.66, p<0.01) and illite (r=0.87, p<0.001). According to the influence of different soil parameters on adsorption, different mechanisms of adsorption are proposed for each surfactant. Our findings point to the interest of considering the physicochemical properties of soils and also the mineralogy of the soil clay fraction when selecting a surfactant in technologies involving enhanced solubilization and removal of contaminants from soils and sediments.     

Kinetics of hydrolysis and cyclization of ethyl 2-(aminosulfonyl)benzoate to saccharin

The cyclization of ethyl 2-(aminosulfonyl)benzoate (ASB) to give saccharin was investigated in aqueous solutions at pH between 5.2 and 9.5 and in the temperature range of 296.2-334.2 K. The initial concentration of the reactant was varied between 1.45 x 10(-5) and 3.86 x 10(-4) M. Ultraviolet spectroscopy was used to obtain the kinetic data. The reaction is acid catalyzed and follows pseudo-first-order kinetics. The experimental rate constant, k(obs), increases with temperature and pH. Its dependence on the temperature and pH is well described by: k(obs) = k1 [OH-] = [(2.52 +/- 0.9) x 10(16) exp(-20.2 +/- 1 kcalmol(-1)/RT) s(-1)][OH-] A mechanism is proposed and the half-life of ethyl ASB is calculated.     

Effect of pH and the role of organic matter in the adsorption of isoproturon on soils

Equilibrium measurements were carried out with the herbicide isoproturon on natural adsorbents (brown forest-, chernozem-, sandy soils and quartz) in different buffered media (pH 5, 7, 8 phosphate buffer). Adsorption isotherms were fitted by a multi-step adsorption equation providing numerical information used in the environmental propagation models and risk assessment works. In the adsorption of the slightly polar isoproturon the dissolved organic matter of the soil and the pH play an important role. At molecular level, results are interpreted by taking into consideration the hydrophobic interaction and the formation of hydrogen bonds between the surface and the solute. The observed adsorption behavior indicates that the organic matter content of the soils and its soluble fulvic acid, alkaline soluble humic acid and insoluble humin fractions were considerable different. The chernozem soil containing the highest amount of insoluble organic fraction proved to be a very efficient adsorbent. The brown forest and the sandy soils exhibit rather similar adsorbent properties but at pH 7 the latter containing more fulvic acid adsorbs less isoproturon due to the enhanced solubility of the soil organic matter. In alkaline conditions the negatively charged solute and the surface repel each other and the hydrophobic interactions are also weaker than in neutral media.     

Adsorption and thermodynamic parameters of chlorantraniliprole and dinotefuran on clay loam soil with difference in particle size and pH

The behavior of chlorantraniliprole (CAP) and dinotefuran (DNF) insecticides was investigated in clay loam soil, a common type of the Egyptian soil. Effect of temperature, pH and particle size of the soil on the adsorption process was studied. Adsorption isotherm by bulk soil and its constituents; humic acid (HA), clay, silt and sand fractions was measured using batch equilibration technique. The results showed that the adsorption of the insecticides tested was significantly affected by the temperature and was a spontaneous interfacial process in the soil. Freundlich model accurately predicted the adsorption behavior of both insecticides. The interaction between soil and insecticides was endothermic and the highest adsorption for CAP and DNF was obtained at pH 9. However, the effect of pH on the adsorption of DNF was lower than that of CAP. Sorption of CAP and DNF on HA fraction was significantly greater than on clay fraction and bulk soil. In addition, the adsorption was significantly increased with particle size decrease. It could be inferred that the adsorption of CAP and DNF on clay loam soil was physical in nature and greatly influenced by the soil components, pH and temperature.     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.     

Catalytic ozonation of 2,4-dichlorophenoxyacetic acid using alumina in the presence of a radical scavenger

Using a laboratory-scale mixed reactor, the performance of alumina in degrading 2,4-Dichlorophenoxyacetic acid with ozone in the presence of tert-butyl alcohol radical scavenger was studied. The operating variables investigated were the dose of alumina catalyst and solution pH. Results showed that using ozone and alumina leads to a significant increase in 2,4-D removal in comparison to non-catalytic ozonation and adsorption processes. The observed reaction rate constants (k(obs)) for 2,4-D during ozonation were found to increase linearly with increasing catalyst dose. At pH 5, the k(obs) value increased from 19.3 to 26 M(-1) s(-1) and 67 M(-1) s(-1) when varying the alumina dose from 1 to 2 and 4 g L(-1), respectively. As pH was increased, higher reaction rates were observed for both non-catalytic ozonation and catalytic ozonation processes. Thus, at pH 3 and using a catalyst dose of 8 g L(-1), the k(obs) values for non-catalytic ozonation and catalytic ozonation processes were 3.4 and 58.9 M(-1) s(-1), respectively, whereas at pH 5 reaction rate constants of 6.5 and 128.5 M(-1) s(-1) were observed, respectively. Analysis of total organic carbon suggested that catalytic ozonation with alumina achieved a considerable level of mineralization of 2,4-D. Adsorption of 2,4-D on alumina was found to play an important role in the catalytic ozonation process.     

A comparison of five pesticides adsorption and desorption processes in thirteen contrasting field soils

Batch adsorption and desorption experiments were performed using thirteen agricultural soil samples and five pesticides. Experimental data indicated a gradient in pesticide adsorption on soil: trifluralin > 2,4-D > isoproturon> atrazine > bentazone. Atrazine, isoproturon and trifluralin adsorption were correlated to soil organic matter content (r2 = 0.7, 0.82, 0.79 respectively). Conversely, bentazone adsorption was governed by soil pH (r2 = 0.68) while insignificant effect has been shown in the case of 2,4-D. Multiple linear regressions were used to combine relationships between the various soil parameters and the Freundlich adsorption coefficient (K(f)) of each pesticide. Then desorption was assessed since it may reflect some of the interactions involved between the pesticides and the soil components. Adsorbed molecules were released into aqueous solution in the following order: bentazone > atrazine> isoproturon> 2,4-D > trifluralin. The occurrence of hysteresis did not allow an accurate interpretation of the pesticide desorption data because of the possible interplay of several processes.     

Adsorption characteristics of pesticides methamidophos and glyphosate by two soils

Contributions of organic matter and minerals in soil were evaluated by comparing changes in adsorption of methamidophos (MDP) and glyphosate (GPS) before and after removal of organic matter from argaltoll (mollisol) and typustalf (alfisol) soils. Adsorption isotherms of MDP and GPS by the two soils comforted to Freundlich equation, and the adsorption capacity of GPS by argaltoll soil was higher than that of MDP. Due to the removal of organic matter from soils, K(f) values of MDP and GPS adsorbed by argaltoll soil, which were calculated from Freundlich equations and the measure of adsorption capacity, decreased by 46.1% and 75.0%, and these by typustalf soil decreased by 34.9% and 52.5%, respectively. Results from this study suggested that soil organic matter made greater contributions to adsorption of GPS, but soil minerals could provide more available adsorption sites for MDP.     

Adsorption and cosorption of cadmium and glyphosate on two soils with different characteristics

Glyphosate [N-(phosphonomethyl)glycine] (GPS; H3G) is a widely used pesticide throughout the world. It affects metal behaviors in soil-plant system due to its functional groups, which react with metal ions to form metal complexes. Adsorption and cosorption of cadmium and glyphosate on a Wushan soil (WS soil, Anthrosol) and a Zhuanhong soil (ZH soil, Udic Ferrisol) as affect by solution pH were studied by means of batch adsorption experiments. It indicated that the adsorption quantity of Cd or glyphosate was highly relevant to soil characteristics. The WS soil had higher adsorption capacity of Cd than the ZH soil, due to its high organic matter content and cation exchange capacity (CEC). In contrast, the adsorption quantity of glyphosate on the WS soil was less than that on the ZH soil, because the WS soil has lower iron and aluminum oxides content but higher pH than the ZH soil. The herbicide glyphosate affected Cd adsorption on the two soils when they coexisted in a same soil solution, which was attributed to a glyphosate-induced pH-decrease and the corresponding decline in negative surface charges of the soil. Beside that, glyphosate reacted with solution Cd to form the water-soluble complexes that had lower affinity to soil surface in comparison with Cd itself. On the other hand, the presence of Cd in the soil solution also affected the adsorption of glyphosate on the soils. The presence of Cd increased adsorption quantity of glyphosate on the WS and ZH soils, which was resulted from the decrease of equilibrium solution pH caused by Cd2+ exchange with H+ ions of soil surface. In addition to that, glyphosate adsorption possibly takes place on sites where Cd was previously adsorbed and acted as a bridge between the soil and glyphosate.     

外源硅对不同pH水田土壤吸附铅的影响

通过等温吸附实验,研究了加硅对2种不同pH水田土壤吸附铅特性的影响。实验中用硝酸中和硅酸钠的碱性,各处理间钠离子和硝酸根离子的差异以硝酸钠补齐,消除了因硅酸盐的加入改变体系pH及伴随离子对土壤吸附铅可能产生的影响。结果表明,在本实验条件下,Langmuir方程、Freundlich方程和Temkin方程都能较好地描述不同硅浓度条件下两种土壤对铅的吸附特征,但以Freundlich模型为最优;加硅促进了酸性土壤对铅的吸附,抑制了碱性土壤对铅的吸附。     

Paraquat adsorption, degradation, and remobilization in tropical soils of Thailand

Paraquat adsorption, degradation, and remobilization were investigated in representative tropical soils of Yom River Basin, Thailand. Adsorption of paraquat in eight soil samples using batch equilibration techniques indicated that adsorption depended on soil characteristics, including exchangeable basic cations and iron content. Multiple regression analysis indicated significant contribution of exchangeable calcium percentage (ECP), total iron content (TFe) and exchangeable sodium percentage (ESP) to paraquat sorption (Q). ESP and TFe were significant at all adsorption stages, whereas ESP was significant only at the initial stage of paraquat adsorption. Adsorption studies using two soils representing clay and sandy loam textures showed that paraquat adsorption followed the Freundlich model, exhibiting a nonlinear sorption curve. Paraquat adsorption was higher in the clay soil compared to the sandy loam soil with Kf values of 787 and 18, respectively. Desorption was low with 0.04 to 0.17% and 0.80 to 5.83% desorbed in clay and sandy loam soil, respectively, indicating some hysteresis effect. Time-dependent paraquat adsorption fitted to the Elovich kinetic model indicated that diffusion was a rate-limiting process. Paraquat mobility and degradation studies conducted using both field and laboratory soil column experiments with clay soil showed low mobility of paraquat with accumulation only in the surface 0-5 cm layer under field conditions and in the 0-1 cm layer in a laboratory soil column experiment. Degradation of paraquat in soil was faster under field conditions than at ambient laboratory conditions. The degradation rate followed a first-order kinetic model with the DT50 at 36-46 days and DT90 around 119-152 days.     

改性玉米秸秆吸附Cu^2＋的动力学和热力学

本研究用ZnCl2作为活化剂,使用功率640W的微波照射4min的方法制备改性玉米秸秆。考察投加量、pH、吸附时间对吸附性能的影响,并对等温吸附特征、吸附动力学和热力学进行了系统研究。结果表明：投加量为0．2g,pH为6,改性玉米秸秆对Cu^2＋具有很好的吸附效果,吸附在8h后达到平衡。该吸附过程符合Langmuir及Freundlich等温吸附模型和准二级动力学方程,其反应的吉布斯自由能△G〈0,为自发反应过程。     

Behavior of two phenyl urea herbicides in clayey soils and effect of alternating dry-wet conditions on their availability

Adsorption and mobility of linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and diuron (3-(3,4-dichlorophenyl)-1, 1-dimethylurea) were studied in clayey soils from the Gharb area (Morocco). Soils A and B were planted with sun flower (Helianthus annuus) while soil C was planted with sugar cane (Saccharum offcinarum). Adsorption was studied for linuron in soils A and B, while mobility was studied only in soil B. Adsorption data were found to fit the Freundlich equation with correlation coefficients r2 > 0.9. Freundlich coefficients (Kf, nf) were in agreement with L and S isotherm types for soils A and B, respectively. Values of Koc (195 and 102) indicate moderate adsorption. Desorption isotherms for linuron showed hysteresis for both soils. The pesticide would be more bound to soil A (H = 8.44) than to soil B (H = 4.01). The effect of alternating wet and dry conditions was tested for soils A and B. Results showed that retention would increase in soil subject to an additional wet and dry cycle. In the case of diuron isotherm was of type L in soil C. Desorption was noticeable at high concentrations and tended to decrease when concentrations diminished. Mobility of linuron was tested in polyvinyle chloride (PVC) columns, which received different treatments before their percolation. The pesticide was more mobile in a previously saturated column. In columns subject to a drying step after saturation with water, linuron mobility was greatly reduced.     

Sorption-desorption behavior of metsulfuron-methyl and sulfosulfuron in soils

Sorption of metsulfuron-methyl and sulfosulfuron were studied in five Indian soils using batch sorption method. Freundlich adsorption equation described the sorption of herbicides with K(f) (adsorption coefficient) values ranging between 0.21 and 1.88 (metsulfuron-methyl) and 0.37 and 1.17 (sulfosulfuron). Adsorption isotherms were L-type suggesting that the herbicides sorption decreased with increase in the initial concentration of the herbicide in the solution. The K(f) for metsulfuron-methyl showed good positive correlation with silt content (significant at p = 0.01) and strong negative correlation with the soil pH (significant at p = 0.05) while sorption of sulfosulfuron did not correlate with any of the soil parameter. Desorption of herbicides was concentration dependent and, in general, sulfosulfuron showed higher desorption than the metsulfuron-methyl. The study indicates that these herbicides are poorly sorbed in the Indian soil types and there may be a possibility of their leaching to lower soil profiles.     

Effect of o-phenylenediamine on Cu adsorption and desorption in red soil and its uptake by paddy rice (Oryza sativa)

A study was carried out of Cu adsorption and desorption processes in red soil as affected by o-phenylenediamine (o-PD) in the range 0-80 mg/l. The results indicated that the presence of o-PD enhanced Cu adsorption in red soil in weakly acid media, meanwhile, desorption percentage of Cu from soil, extracted by 1.0 M MgCl(2), also increased when Cu adsorption in soil occurred in the presence of o-PD. The response of paddy rice to Cu in red soil shows that Cu toxicity was mitigated in the presence of o-PD and that the Cu concentration in rice straw decreased with increasing concentration of o-PD from 0 to 4.0 mmol/kg in soil. The fractions of background Cu in soil did not change noticeably in the presence of o-PD, whereas the effect of o-PD on the fractions of added Cu was significant. It was found that the exchangeable and carbonate bound Cu fractions decreased and the fraction of Cu bound to Fe-Mn oxides and organic matter increased with increasing o-PD concentration in soil when Cu was added at the same rate. Copper concentration in rice straw was significantly correlated with exchangeable Cu (r=0.961) and carbonate bound Cu (r=0.959) in soil. This result implicates that the behavior of Cu in soil is likely to be affected by organic pollutants containing amino groups.