烟道式脱硫装置处理冶炼厂高浓度SO2烟气的工程实践

本文介绍了烟道式脱硫装置的特点及工艺原理，采用该装置处理某冶炼厂高浓度SO2烟气，其脱硫率达90％以上，净化后的烟气可直拉达标排放，并年产合格脱硫石膏近万吨。烟道式脱硫装置解决了常规脱硫除尘装置共同存在的结垢和堵塞问题，在冶炼烟气治理方面具有一定的推广应用价值。     

湿式旋流脱硫除尘一体化装置在燃煤锅炉烟气净化上的应用

某中药厂4 t/h燃煤锅炉烟气采用湿式旋流脱硫除尘一体化装置取得了良好的效果,经实际运行测定除尘率达95%,脱硫率达77%,排出的烟气均能达到排放标准.该净化装置具有旋风水膜除尘器和湿式旋流板洗涤器的双重功能,通过介绍该一体化装置的机理、设计参数和技术经济分析,为燃煤锅炉烟气的脱硫除尘提供参考.     

烟道式脱硫装置处理冶炼厂高浓度SO2烟气的工程实践

本文介绍了烟道式脱硫装置的特点及工艺原理 ,采用该装置处理某冶炼厂高浓度SO2 烟气 ,其脱硫率达 90 %以上 ,净化后的烟气可直接达标排放 ,并年产合格脱硫石膏近万吨。烟道式脱硫装置解决了常规脱硫除尘装置共同存在的结垢和堵塞问题 ,在冶炼烟气治理方面具有一定的推广应用价值。     

氧化镁湿法烟气脱硫首次应用于燃油工业炉的工程实践

介绍了国内燃油工业炉首次应用氧化镁湿法烟气脱硫的运行情况.设计脱硫前SO2质量浓度1 200 mg/mN3,脱硫率95%;实际运行脱硫前SO2质量浓度250 mg/mN3以下,脱硫后SO2质量浓度在10 mg/mN3以下,脱硫率达97%以上,污水达标排放,吨SO2减排成本为4 983.8元,折算成吨原油加工成本为0.2...     

湿式逆流喷淋脱硫塔中SO_2吸收特性的研究

根据双模吸收理论及SO2在溶液中电离特性,建立了逆流喷淋塔的SO2吸收模型,在考虑浆液飞溅到塔壁的影响后,模拟结果与实验值吻合较好。根据吸收模型,对塔内液气比和浆液的含固率等因素进行了分析。研究表明:减少浆液飞溅到塔壁可提高浆液利用率及脱硫装置性能;根据烟气中SO2的初始浓度及最终脱硫效率,可合理选择液气比及吸收时间(塔的高度);浆液中的含固率直接影响到SO2的吸收速率、循环浆液量、脱硫效率及浆液中SO2浓度等,在液气比较小时,含固率对脱硫效率的影响尤其明显。     

湿式逆流喷淋脱硫塔中SO2吸收特性的研究

根据双模吸收理论及SO2在溶液中电离特性,建立了逆流喷淋塔的SO2吸收模型,在考虑浆液飞溅到塔壁的影响后,模拟结果与实验值吻合较好。根据吸收模型,对塔内液气比和浆液的含固率等因素进行了分析。研究表明：减少浆液飞溅到塔壁可提高浆液利用率及脱硫装置性能;根据烟气中SO2的初始浓度及最终脱硫效率,可合理选择液气比及吸收时问（塔的高度）;浆液中的含固率直接影响到SO2的吸收速率、循环浆液量、脱硫效率及浆液中SO2浓度等,在液气比较小时,含固率对脱硫效率的影响尤其明显。     

燃煤锅炉烟气除尘系统改造

烷基苯厂锅炉烟气除尘系统改造选用文丘里麻石水膜除尘器,除尘脱硫废水与碱性冲渣水中和、过滤后再循环泵提升至冲渣系统,实现燃煤锅炉除尘脱硫废水循环利用。改造后的除尘系统运行情况良好,锅炉的烟尘排放浓度及烟气黑度均达到了国家现行三类区排放标准,二氧化硫排放浓度低于国家允许排放标准。     

气喷旋冲脱硫技术在梅钢3号烧结机中的应用

针对烧结烟气的特点,采用气喷旋冲脱硫技术对梅钢3号烧结机产生的烧结烟气进行烟气脱硫.结果表明,气喷旋冲脱硫系统适合处理烧结烟气,运行稳定,Ca/S为1.03时脱硫率在95%以上.介绍了气喷旋冲脱硫系统的运行情况、技术特点以及运行时的主要参数,为国内同行提供借鉴.     

鼓泡塔中有机酸强化粗颗粒石灰石新型烟气脱硫

对传统石灰石湿法烟气脱硫进行了改进,提出了一种新型烟气脱硫方法,即在鼓泡塔中添加有机酸,采用大颗粒石灰石(210 μm)代替传统的细颗粒石灰石(5～20 μm)进行脱硫.实验在鼓泡搅拌吸收反应器中对比研究了新老两种脱硫工艺.结果表明,当210 μm石灰石浆液中醋酸摩尔浓度达10～30 mmol/L,其脱硫率和石灰石利用率分别为95%和93.5%,均达到甚至优于传统石灰石脱硫结果.实验研究了影响脱硫率的各种因素:添加醋酸浓度、入口SO2浓度、石灰石浆液浓度、气体停留时间以及温度等,并提出添加醋酸促进SO2吸收的机理.运用该新型烟气脱硫方法,可降低电厂的基础投资和运行费用,大大加强系统的稳定性和抗击烟气中SO2波动的能力.     

石灰-石膏法旋流板塔脱硫技术及其应用

石灰-石膏法旋流板塔烟气脱硫技术将石灰-石膏法脱硫工艺与高效传质的旋流板塔设备相结合,具有运行可靠性高、脱硫效率高、一次性投资低、运行费用低的优点.该技术已成功应用于江苏某企业3台170 t/h煤粉炉烟气脱硫除尘,其运行效果均达到或超过设计值,并通过环保验收,为企业带来了可观的经济效益和环境效益.     

Simultaneous absorption of NO and SO2 into hexamminecobalt(II)/iodide solution

An innovative catalyst system has been developed to simultaneously remove NO and SO2 from combustion flue gas. Such catalyst system may be introduced to the scrubbing solution using ammonia solution to accomplish sequential absorption and catalytic oxidation of both NO and SO2 in the same reactor. When the catalyst system is utilized for removing NO and SO2 from the flue gas, Co(NH3)(6)2+ ions act as the catalyst and I- as the co-catalyst. Dissolved oxygen, in equilibrium with the residual oxygen in the flue gas, is the oxidant. The overall removal process is further enhanced by UV irradiation at 365 nm. More than 95% of NO is removed at a feed concentration of 250-900 ppm, and nearly 100% of SO2 is removed at a feed concentration of 800-2500 ppm. The sulfur dioxide co-existing in the flue gas is beneficial to NO absorption into hexamminecobalt(II)/iodide solution. NO and SO2 can be converted to ammonium sulfate and ammonium nitrate that can be used as fertilizer materials. The process described here demonstrates the feasibility of removing SO2 and NO simultaneously only by retrofitting the existing wet ammonia flue-gas-desulfurization (FGD) scrubbers.     

电化学法去除SO2/NOX的研究进展

本文对采用电化学方法去除SO2/NOx废气这一新的研究方法进行了综述.在用酞花青钴(CoPc)修饰的碳气体扩散电极上,SO2在空气中的体积百分数在20%以下时可以完全被氧化为硫酸,以连二硫酸盐(S2O2-4)作还原剂,Fe2+-EDTA作络合剂时,NO以90%以上的程度还原为NH+4与NH2(SO3H)等低价含氮化合物,产物中未见N2、N2O与NO2等气体,氧化产物SO2-3(或HSO-3)在Pb阴极上还原再生为S2O2-4.用Ce4+作氧化剂可将SO2/NO2氧化为相应的酸,还原产物Ce3+经电解氧化后循环使用.     

Simulation of stack plume opacity

The visual impact of primary particles emitted from stacks is regulated according to stack opacity criteria. In-stack monitoring of the flue gas opacity allows plant operators to ensure that the plant meets U.S. Environmental Protection Agency opacity regulations. However, the emission of condensable gases such as SO3 (that hydrolyzes to H2SO4), HCl, and NH3, which may lead to particle formation after their release from the stack, makes the prediction of stack plume opacity more difficult. We present here a computer simulation model that calculates the opacity due to both primary particles emitted from the stack and secondary particles formed in the atmosphere after the release of condensable gases from the stack. A comprehensive treatment of the plume rise due to buoyancy and momentum is used to calculate the location at which the condensed water plume has evaporated (i.e., where opacity regulations apply). Conversion of H2SO4 to particulate sulfate occurs through nucleation and condensation on primary particles. A thermodynamic aerosol equilibrium model is used to calculate the amount of ammonium, chloride, and water present in the particulate phase with the condensed sulfate. The model calculates the stack plume opacity due to both primary and secondary particles. Examples of model simulations are presented for three scenarios that differ by the emission control equipment installed at the power plant: (1) electrostatic precipitators (ESP), (2) ESP and flue gas desulfurization, and (3) ESP and selective catalytic reduction. The calculated opacity is most sensitive to the primary particulate emissions. For the conditions considered here, SO3 emissions showed only a small effect, except if one assumes that most H2SO4 condenses on primary particles. Condensation of NH4Cl occurs only at high NH3 emission rates (about 25 ppm stack concentration).     

垃圾渗滤液烟气脱硫体系的实验研究

利用垃圾渗滤液中较高的碱度吸收二氧化硫是垃圾渗滤液湿法烟气脱硫工艺的第一阶段。试验证明 ,垃圾渗滤液可高效吸收二氧化硫 (去除率可达 90 %以上 ) ;同时垃圾渗滤液中氨氮浓度由 133mmol L降至 78mmol L。实验结果证实了所建立的垃圾渗滤液烟气脱硫体系的互补性     

半干法烟气脱硫新技术——粉末-颗粒喷动床技术

粉末 颗粒喷动床 (powder particlespoutedbed ,PPSB)是近几年来由日本研究人员开发的一种新的半干法烟气脱硫技术。本文介绍了PPSB的基本原理、优点以及在试验条件下所得到的影响因素和适宜的运行方式。PPSB在系统结构、废物处理、操作和费用方面比湿法有所提高 ,同时又比干法和其他半干法的去除率和吸收剂的利用率高。此外 ,对吸收剂研究结果表明 ,石灰石的脱硫效率虽然不及石灰 ,但是由于PPSB中吸收剂的停留时间长 ,气、固、液三相接触好的特点以及可以对石灰石进行研磨 ,因此 ,利用石灰石作吸收剂的PPSB完全可以达到理想的脱硫效率 ,同时也可以保持较好的经济性。但是 ,目前还没有大规模的试验和应用。所以PPSB是一项十分值得进一步开发和应用的烟气脱硫新技术。     

锅炉烟气联合脱硫脱氮技术

硫氧化物和氮氧化物是燃煤锅炉排放的主要污染物 ,传统分步脱硫脱氮设备昂贵且效率不高 ,而联合脱硫脱氮技术具有很大的优越性 ,如可以减小系统的复杂性、具有更好的运行性能、较低的成本及较小的占地面积 ,因此实现在一个系统内同时脱硫脱氮的工艺成为国内外烟气净化技术的研究重点。对近年来国内外各种联合脱硫脱氮技术的脱除原理、研究现状、应用情况和主要优缺点进行了论述 ,并对各工艺的经济技术指标给予了多方面的比较。通过对两类烟气联合脱硫脱氮技术 (炉内联合脱除和烟气中联合脱除 )的分析、综合和比较 ,找出了我国今后脱硫脱氮技术的研究重点 ,从而为脱硫脱氮技术的进一步开发和改进提供参考     

The effect of coal combustion flue gas components on low-level chlorine speciation using EPA method 26A

U.S. Environmental Protection Agency (EPA) Method 26A is the recommended procedure for capturing and speciating halogen (X2) and hydrogen halide (HX) stack emissions from combustion sources. Previous evaluation studies of Method 26A have focused primarily on hydrogen chloride (HCl) speciation. Capture efficiency, bias, and the potential interference of Cl2 at high levels (> 20 ppm [microgram/m3]) and NH4Cl in the flue gas stream have been investigated. It has been suggested that precise Cl2 measurement and accuracy in quantifying HX or X2 using Method 26A are difficult to achieve at Cl2 concentrations < 5 ppm; however, no performance data exist to support this. Coal contains low levels of Cl, in the range of 5-2000 ppmw, which results in the presence of HCl and Cl2 in the products of combustion. HCl is the predominant Cl compound formed in the high-temperature combustion process, and it persists in the gas as the products of combustion cool. Concentrations of Cl2 in coal combustion flue gas at stack temperatures typically do not exceed 5 ppm. For this research, bench-scale experiments using simulated combustion flue gas were designed to validate the ability of Method 26A to speciate low levels of Cl2 accurately. This paper presents the results of the bench-scale tests. The effect of various flue gas components is discussed. The results indicate that SO2 is the only component in coal combustion flue gas that has an appreciable effect on Cl2 distribution in Method 26A impingers, and that Method 26A cannot accurately speciate HCl and Cl2 in coal combustion flue gas without modification.     

软锰矿浆烟气脱硫反应机理研究

利用软锰矿浆吸收烟气中SO2 ,该方法不仅可脱硫 ,还可副产具有工业价值的硫酸锰产品 ,是一种较好的脱硫资源化方法。通过对软锰矿浆与SO2 的反应机理的分析和实验验证 ,确定该体系的主要反应 ,为该工艺过程可行性研究提供理论和实践依据     

双循环多级水幕吸收塔烟气除尘脱硫性能研究

以改进后的双循环多级水幕塔对烟气进行除尘脱硫性能的研究,利用双循环不同pH值控制的优点和多级水幕的效果,增加气液接触面积和传质动力,提高SO₂吸收效果。在正交实验的最佳运行工况基础上,实验从烟气流量、上下两段pH、L/G和SO₂进气浓度等方面进行单因素研究。结果表明,除尘效率维持在98%以上,进气SO₂浓度在5 000 mg/m³以下时,脱硫率在93%以上。上段pH值为6、下段pH值为5、L/G在15左右的脱硫效率和运行工况最佳,无结垢现象发生。改进后的吸收塔具有良好的应用前景,实验结果对于现场脱硫设备的调试和运行有很好的参考价值。     

烟气中多种污染物协同脱除的研究

烟气中多种污染物协同脱除是烟气净化领域的研究热点.在现有烟气脱硫技术研究的基础上,对活性焦干法、多级增湿半干法、氧化性添加剂湿法以及等离子体湿法这4种烟气污染物协同脱除技术进行了系统的研究.研究发现,以活性焦为载体添加适当的催化剂能够实现在高效脱硫基础上的同时脱硝;多级增湿半干法技术提高了脱硫剂颗粒在吸收塔内反应全过程的含湿均匀性,通过添加复合促进剂可以提高反应速率,强化烟气中SO_2、NO_X等污染物协同脱除;在传统的湿法烟气脱硫技术中,向脱硫剂中加入KMnO_4和NaClO_2等强氧化剂或者采用等离子体前置氧化,能够有效的将难吸收的NO氧化成NO_2、HNO_2和HNO_3,最终实现同时脱硫脱硝.