梨形筒式好氧堆肥反应器的开发与应用

针对现有堆肥反应器移动困难、难以使物料充分混合及堆肥效率不稳定等问题,开发了梨形筒式好氧堆肥反应器。从物料和热量平衡、通风量及搅拌方式优化等方面对反应器进行了研究。反应器主要包括梨形筒体、无轴螺旋导叶、通风系统、动力系统和控制系统等,具有易于移动、便于进/出料等优点。在通风量为2.0 L/min,初始物料投加量5.0kg（干重比∶粪便/锯末=1∶4）,含水率约60%时,利用反应器对人粪便进行序批式堆肥实验,结果表明,反应器搅拌5 min后混合均匀率可达90%以上,符合混合均匀度的要求;堆体温度从第2天开始升温至50℃以上并保持30 d;TOC和COD均呈持续下降趋势,降解率分别为72.61%和72.81%;种子发芽指数为92.18%,可完全达到腐熟标准。     

初始温度对人粪便好氧堆肥过程的影响

温度是好氧堆肥过程中需要控制的一个重要因素。不同的初始温度直接影响了堆肥过程中微生物活性及有机物的降解。为了研究初始温度对粪便好氧堆肥过程的影响,采用序批式好氧堆肥反应器,以新鲜锯末为载体,控制含水率在55%~60%的范围左右并强制通风的好氧条件下,进行了初始温度分别为25、35、45和55℃,20 d为一个周期好氧堆肥实验,研究了不同初始温度条件下堆肥过程有机物降解、氮的迁移转化及种子发芽指数的变化。结果表明,初始的高温度会抑制堆肥反应的进行,但初始温度越高,水解效果越显著;初始的高温有利于COD的去除,最终COD的去除率分别为88.2%、89.3%、92.0%和89.9%。初始高温对种子发芽率有抑制作用,同时延迟了堆肥的腐熟期。     

投加方式和通风速率对脱水污泥堆肥效果的影响

为了在降低能耗的前提下获得更高的污泥堆肥效率和提高堆肥产品质量,利用梨形筒式好氧堆肥反应器,设置2种物料投加方式和3种通风速率,研究堆肥过程中温度、含水率、总氮以及发芽指数（GI）的变化特性。结果表明,与间歇式堆肥相比,连续式堆肥可以显著提高堆体温度和堆体腐熟度,降低堆体含水率及缩短腐熟期,但氮素损失也显著增大（P-1的连续式堆肥,堆体维持高温时间最长,且最终温度稳定在较高温度47～48 ℃,堆末含水率最低,氮素损失处于三者的中间水平,腐熟期最短。综合分析,在通风速率为1.95 L·min-1的连续运行方式下,梨形筒式反应器用于污泥稳定高效堆肥是可行的。     

卧式螺旋污泥好氧动态堆肥技术的研究

利用卧式螺旋式污泥好氧堆肥装置进行间歇式动态堆肥,对污水厂厌氧消化污泥进行了中温堆肥试验研究.通过控制各组堆肥的含水率、物料配比和通气量,重点探讨各种条件下堆体温度与有机物降解的关系.试验结果表明,厌氧消化污泥以木屑为调理剂在装置中可以实现好氧堆肥处理,其适宜的物料控制参数为:污泥:木屑=10:1～1.5(湿重比),堆肥含水率50%～60%;过程控制参数为:通风量为6.7～8.3 m3/h·t,发酵周期为8 d,温度45℃.     

好氧堆肥反应器对人粪便堆肥中温降解的中试研究

控制温度为（35±2）℃,以新鲜锯末为空白载体,在控制含水率为55%~60%和强制通风的好氧条件下,进行为期15 d的实验,进行了人粪便好氧堆肥的中试研究,重点分析了在堆肥过程中有机物的降解、氮素的迁移转化规律及生物量的变化。结果表明,粪便中有机物含量在前2天稍微上升,然后迅速下降,最终去除率为71.82%;随着NH₃-N释放量的增加,堆料中N_tot含量从第4天开始减少,最终损失 22.61%,其中N_org损失占74.35%,NH₃-N占23.52%;所损失的氮素有91.66%以氨氮的形式释放。粪便中的有机物和氮的含量能在8~10 d后达到稳定,且堆体无臭味;粪便中溶解性有机物为微生物的生长提供营养物质,因此生物量变化的过程与有机物降解的有着紧密的联系;病原菌在堆肥过程中得到有效去除,表明该反应器堆肥的无害化。     

接种微生物与人粪便同步连续投加对好氧堆肥效果的影响简

利用新型梨形筒式好氧堆肥反应器,在通风量为3.0 L/min,搅拌频率为5 min/h的条件下,就不接种微生物、接种土著菌种、枯草芽孢杆菌与酵母菌时人粪便连续投加好氧堆肥效果进行了对比。堆制20 d即2个运行周期中各堆体的温度、含水率、COD、总氮、pH值与GI等的变化表明,接种微生物可以显著提高堆体的升温速率与堆体平均温度、COD降解率、GI（P<0.01）,堆肥可迅速达到完全腐熟。接种土著菌种效果最为明显（P<0.01）,其后相继为枯草芽孢杆菌与酵母菌。接种土著菌种可使堆体温度在50℃以上维持18 d,第8天COD降解率达到61.17%、总氮损失率为25.75%,第6天时GI达到108.22%。     

小型好氧堆肥设备处理有机垃圾

针对我国生活垃圾的特点,提出了厨余等有机生活垃圾单独收集,在产生源头进行好氧堆肥处理。研制了好氧堆肥设备,由加热装置、通风装置、冷凝水收集和回灌装置,以及与该生物堆肥设备配套的生物过滤除臭装置、自控系统和数据采集软件几部分构成。自控系统由氧气、温度、湿度三路传感器以及2个控制器构成,并与加热装置、通风装置连接,能满足物料加热、供氧和散热的要求。本研究通过为期30 d的试运行实验表明,物料快速升温并稳定保持在高温阶段(50～60℃),物料中的氧气浓度保持在14%～16%范围内。在堆肥实验结束时,物料的含水率降至36.4%,有机质含量降至49%,另外,通过好氧速率指标也可判定物料达到腐熟。     

粪便与生活垃圾混合堆肥过程控制

采用强制通风静态仓进行粪便和生活垃圾混合堆肥,以玉米秸为调理剂,石灰调节pH,考察正压鼓风和负压抽吸2种通风方式对不同堆料配比堆肥过程的控制效果。试验结果表明,5种堆料配比的中层温度都达到了50℃,并保持了5 d以上,达到了堆肥无害化和稳定化的要求。正压鼓风堆料底部温度较低,负压抽吸堆料底部热量容易聚集,但是后者堆体温度分布相对均匀。负压抽吸对水分的去除效果差于正压鼓风。对于温度未达到50℃的堆料应回流处理保证无害化。粪便有机物含量高,堆肥初期易酸化,添加石灰调节pH,使堆肥顺利升温,缩短发酵期,石灰合理添加量为2%(质量分数)。采用负压抽吸的通风方式,散除堆肥初期的挥发性有机酸,再经过冷凝除臭器脱酸除臭后排放,是一种可取的方式。     

接种微生物与人粪便同步连续投加对好氧堆肥效果的影响

利用新型梨形筒式好氧堆肥反应器,在通风量为3．0L／min,搅拌频率为5min／h的条件下,就不接种微生物、接种土著菌种、枯草芽孢杆菌与酵母菌时人粪便连续投加好氧堆肥效果进行了对比。堆制20d即2个运行周期中各堆体的温度、含水率、COD、总氮、pH值与GI等的变化表明,接种微生物可以显著提高堆体的升温速率与堆体平均温度、COD降解率、Ct（P〈0．01）,堆肥可迅速达到完全腐熟。接种土著菌种效果最为明显（P〈0．01）,其后相继为枯草芽孢杆菌与酵母菌。接种土著菌种可使堆体温度在50℃以上维持18d,第8天COD降解率达到61．17％、总氮损失率为25．75％,第6天时GI达到108．22％。     

筒仓式堆肥反应器不同通风量对堆肥效果的影响

使用筒仓式堆肥反应器,利用含水率为70%的鸡粪作为堆肥原料,分别向堆料中通入12、6和2.4 m3·min-13种不同的通风量,研究不同的通风量对堆肥效果的影响。研究表明,合理的通风量对于堆肥的快速发酵非常重要,通风量为12 m3·min-1时堆肥效果最佳。当通风量为6 m3·min-1和2.4 m3·min-1时,堆体的全氮含量最终都有所下降,说明其通风量不能满足堆体快速发酵对氧气的需求,所以堆体内发生了部分厌氧反应。而6 m3·min-1的通风处理全磷的增加量最大,说明此处理减少了物料中磷的损失,增加了有效磷的含量。当通风量为12 m3·min-1时,与其他2个处理相比,高温期持续时间更长,有机质降解量更大,氮磷等养分的增加量更大,种子发芽率也更高,这些都说明了通风量为12 m3·min-1时堆肥效果最佳。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.