磷对褐土中锌镉次级吸附和解吸影响

通过吸附和解吸试验,研究了不同磷吸附量石灰性褐土对锌镉次级吸附和解吸的影响。结果表明,次级吸附锌和镉对不同吸附量磷土壤的磷解吸量随磷吸附量的增加而增加,而磷解吸量随次级吸附后锌、镉浓度的增加而降低,即随锌镉添加量的增加,磷的有效性有所降低。土壤对锌的次级吸附量和吸附率随磷吸附量的增加先降低后升高,并随添加镉浓度的增加而降低,解吸量和解吸率随磷吸附量的增加而增加,说明在正常施磷范围内,增加磷的施用量能提高土壤中锌的有效性,同时,土壤对高浓度锌的次级吸附率小于低浓度锌的次级吸附率,而土壤对高浓度锌的解吸量和解吸率要远大于对浓度锌的解吸量和解吸率;土壤对镉的次级吸附量、吸附率和解吸量、解吸率都随着磷吸附量的增加而增加,且吸附量随添加镉的量增加而增加,但镉次级吸附量和吸附率随添加锌浓度的增加而减小,解吸量和解吸率却增大,说明在磷吸附量相同的条件下,添加锌促进了镉的有效性。     

蜂窝煤灰渣和磷肥结合修复铅污染贫磷潮土的研究（Remediation of Lead Polluted Chaotu Soil with Low Phosphorus Availability by Application of Honeycomb Briquette Combustion Residue and Phosphorus Fertilizer）

利用蜂窝煤灰渣和磷肥结合稳定铅污染贫磷(Olsen-P=2.50mg·kg-1)潮土中铅的可行性.采用盆栽试验,设置0和500mg·kg-1两个Pb用量,灰渣用量分别为干土质量的0%和2%,P:Pb分别为0和4.种植黑麦草,植物生长85d后收获,测定植物产量、土壤DTPA-Pb、Olsen-P含量、pH值和电导率(EC).结果表明,在两个Pb用量及两个P:Pb比例下,加入灰渣后,土壤的DTPA-Pb含量均降低,平均降低5.61%.其中加铅未加磷处理灰渣效果达到0.05的显著水平,各加Pb处理中,同时加入磷肥和灰渣处理土壤的DTPA-Pb含量最低;加入灰渣后处理土壤中的Olsen-P含量均增加,平均增加了2.71mg·kg-1,各处理土壤pH值上升约0.1个单位,加入灰渣也导致各处理土壤的EC增加.各处理条件下加入灰渣后植物产量均减小.在未加磷土壤中加入Pb后,土壤Olsen-P含量显著增加(p<0.05),表明高铅有效性下,植物可能通过根系分泌物增加了土壤磷的有效性.以上结果表明,蜂窝煤灰渣有可能用于降低污染土壤中铅的有效性,但其对植物生长的抑制作用需要克服.     

磷锌配施对镉污染石灰性土壤中磷锌镉有效性的影响

为了阐述磷与锌镉在土壤系统中的作用机制,采用室内培养的方法,研究了石灰性褐土在不同镉质量分数处理下磷锌配施对土壤DTPA-Cd、DTPA-Zn及速效磷质量分数的影响.结果表明,土壤中wDTPA-Cd随外加镉质量分数的增加而增加,随施磷质量分数的增加而降低.同时在相同镉质量分数处理下,配施锌能显著降低土壤wDTPA-Cd;土壤中wDTPA-Zn随外加锌质量分数的增加而增加,且随施磷质量分数的增加而增加,而随土壤中添加镉质量分数的增加显著降低;土壤速效磷的质量分数随施磷质量分数的增加而提高,而镉的加入降低了土壤速效磷质量分数,但配施锌能显著提高土壤速效磷质量分数.     

可变电荷土壤和恒电荷土壤Cl-吸附特性的研究

对不同浓度KCl和不同pH下,3种可变电荷土壤和4种恒电荷土壤Cl-吸附量进行了测定。结果表明,土壤Cl-吸附量随平衡Cl-浓度C（e）增加而增大,恒电荷土壤呈线性,可变电荷土壤在添加Cl-0.5~5.0mmol/L下,符合Langmuir吸附等温式。同一浓度下的Cl-吸附量及其随浓度增加的速率均为砖红壤>红壤>赤红壤>黄棕壤>棕壤、暗棕壤和黑土,与这些土壤所带正电荷量顺序相一致。Langmuir方程K值较小且几种土壤差异不大。恒电荷土壤对Cl-的吸附量很小,在浓度较低时常出现负吸附,其吸附机理可能更多的是与K+吸附时的同时吸附。7种土壤Cl-吸附量均随pH增加而降低,但降低强度可变电荷土壤远大于恒电荷土壤。     

堆腐城市生活垃圾对莴笋生长影响的主分量分析

在不同的土壤上,城市生活垃圾对莴笋生长的影响不同。在石灰性土壤上,莴笋产量与垃圾用量间的关系符合对数模型,其边际产量随垃圾用量增加而减少,与一般肥料效应相似;而在强酸性土壤上,莴笋产量与垃圾用量间的关系可用抛物线模型模拟,在试验用量范围内,其边际产量随垃圾用量的增加而增加,显著高于一般肥料效应。通过主分量分析,查明垃圾促进莴笋生长的原因如下：①降低土壤粘性;②改善土壤营养条件;③对于酸性土壤,垃圾     

潮土中磷锌交互作用机制探讨及磷对锌吸附-解吸的影响

采用室内培养和吸附解吸两种方法,探讨了潮土中磷、锌交互作用机制。结果表明：土壤中DTPA提取态锌质量分数随添加锌量的增加而增加,低磷质量分数处理可提高土壤锌有效性,但高磷质量分数处理却降低了土壤锌的有效性;土壤速效磷质量分数均随锌添加量的增加而有所降低。在施锌25 mg.kg-1背景下,土壤中DTPA提取态锌质量分数随施磷质量分数的增加呈先增加后降低趋势,在添加磷量小于180 mg.kg-1时,土壤DTPA提取态锌质量分数显著地高于其他处理,但随添加磷量的增加,土壤DTPA提取态锌质量分数显著降低,当磷添加量大于540 mg.kg-1时,土壤DTPA提取态锌质量分数明显低于其他磷处理,说明当添加磷量小于180 mg.kg-1时,磷提高土壤中锌有效性的主要机制是二者竞争吸附土壤胶体表面吸附点位的竞争机制;当添加磷量大小540 mg.kg-1时,磷影响锌有效性的主要机制为沉淀作用。在土壤施磷量为180 mg.kg-1时,随添加锌质量分数的提高,土壤中速效磷质量分数呈先升高后降低趋势。吸附-解吸研究表明,随土壤中速效磷质量分数的提高（27.60~2773.86 mg.kg-1）,土壤对锌的吸附量先降低再增加,而KCl解吸的锌量却是先增加再降低。因此潮土中磷锌交互作用机制为,土壤中磷和锌质量分数均较低时,磷与锌有效性呈协同作用;当磷或锌质量分数过高时,协同作用减弱;磷和锌质量分数再增加二者的有效性将出现拮抗作用。     

可变电荷土壤和恒电荷土壤CI~-吸附特性的研究

对不同浓度ＫＣＬ和不同ｐＨ下,３种可变电荷土壤和４种恒电荷土壤ＣＩ－吸附量进行了测定。结果表明,土壤ＣＩ－吸附量随平衡 ＣＩ－浓度 Ｃ（ｅ）增加而增大,恒电荷土壤呈线性,可变电荷土壤在添加 ＣＩ－ ０．５－５．０ ｍｍｏｌ／Ｌ．下,符合 Ｌａｎｇｍｕｉｒ吸附等温式。同一浓度下的ＣＩ－吸附量及其随浓度增加的速率均为砖红壤＞红壤＞赤红壤＞黄棕壤＞棕壤、暗棕壤和黑土,与这些土壤所带正电荷量顺序相一致。Ｌａｎｇｍｕｉｒ方程Ｋ值较小且几种土壤差异不大。恒电荷土壤对ＣＩ－的吸附量很小,在浓度较低时常出现负吸附,其吸附机理可能更多的是与Ｋ＋吸附时的同时吸附。７种土壤ＣＩ－吸附量均随ｐＨ增加而降低,但降低强度可变电荷土壤远大于恒电荷土壤。     

石灰性褐土中柠檬酸对土壤Cu(Ⅱ)、Cd(Ⅱ)吸附-解吸的影响

通过室内培养和吸附-解吸实验,研究了不同柠檬酸含量土壤对Cu2+、Cd2+吸附-解吸的影响.结果表明,土壤对Cu2+的吸附量随加入柠檬酸量的增加而明显增加,达到峰值后(柠檬酸含量为0.5 mmol.kg-1),吸附量随柠檬酸含量的增加而下降,即Cu2+的吸附曲线呈峰型.在低柠檬酸含量时,土壤对Cu2+的吸附量受Cd2+浓度影响较小,但随柠檬酸含量的增加,在低铜浓度处理(Cu2+浓度为600 mg·L-1,Cu600)下,土壤对Cu2+的吸附量随Cd2+浓度的增大而增大,但在高浓度铜处理(Cu2+浓度为1000 mg·L-1,Cu1000)下,土壤对Cu2+的吸附量随Cd2+浓度的增加而减少.Cu2+的解吸量随柠檬酸含量的增加而总体上降低;相同柠檬酸含量下,Cu600处理下,Cd2+浓度为10 mg·L-1(Cd10)条件下Cu2+解吸量明显低于无Cd2+(Cd0)和Cd2+浓度为1 mg·L-1(Cd1)条件下.而Cu1000处理下,Cd2+的浓度对Cu2+解吸量的影响较小.Cd2+吸附量随柠檬酸含量的增加无明显变化,但随Cu2+浓度的增加下降明显,其中无Cu2+处理Cd2+吸附量极显著地高于Cu600和Cu1000处理,而Cu600和Cu1000处理间差异不显著,且土壤对Cd2+的吸附随镉添加量增加而增加;Cd2+的解吸量随柠檬酸含量的增加先增大后保持稳定,在柠檬酸含量为0.5 mmol.kg-1时达到最大,Cu600处理的Cd2+的解吸量显著地高于Cu1000处理.     

Effects of citric acid on Cu（Ⅱ） and Cd（ Ⅱ ） adsorption ＆ desorption in calcareous cinnamon soil

通过室内培养和吸附-解吸实验,研究了不同柠檬酸含量土壤对Cu2＋、Cd2＋吸附-解吸的影响.结果表明,土壤对Cu2＋的吸附量随加入柠檬酸量的增加而明显增加,达到峰值后（柠檬酸含量为0.5 mmol.kg-1）,吸附量随柠檬酸含量的增加而下降,即Cu2＋的吸附曲线呈峰型.在低柠檬酸含量时,土壤对Cu2＋的吸附量受Cd2＋浓度影响较小,但随柠檬酸含量的增加,在低铜浓度处理（Cu2＋浓度为600 mg·L-1,Cu600）下,土壤对Cu2＋的吸附量随Cd2＋浓度的增大而增大,但在高浓度铜处理（Cu2＋浓度为1000 mg·L-1,Cu1000）下,土壤对Cu2＋的吸附量随Cd2＋浓度的增加而减少.Cu2＋的解吸量随柠檬酸含量的增加而总体上降低;相同柠檬酸含量下,Cu600处理下,Cd2＋浓度为10 mg·L-1（Cd10）条件下Cu2＋解吸量明显低于无Cd2＋（Cd0）和Cd2＋浓度为1 mg·L-1（Cd1）条件下.而Cu1000处理下,Cd2＋的浓度对Cu2＋解吸量的影响较小.Cd2＋吸附量随柠檬酸含量的增加无明显变化,但随Cu2＋浓度的增加下降明显,其中无Cu2＋处理Cd2＋吸附量极显著地高于Cu600和Cu1000处理,而Cu600和Cu1000处理间差异不显著,且土壤对Cd2＋的吸附随镉添加量增加而增加;Cd2＋的解吸量随柠檬酸含量的增加先增大后保持稳定,在柠檬酸含量为0.5 mmol.kg-1时达到最大,Cu600处理的Cd2＋的解吸量显著地高于Cu1000处理.     

不同磷含量和秸秆添加量对褐土镉吸附解吸的影响

采用室内培养的方法,通过人为添加不同量的玉米干秸秆和磷,研究不同含磷量土壤对镉吸附解吸影响,以探讨磷—镉在土壤中的交互作用机制。结果表明,不同含磷量的土壤对不同质量浓度锌镉吸附解吸时,在低质量浓度镉（Cd3）条件下,土壤对镉的吸附量随磷质量分数的增加先升高后降低,解吸量随着土壤中磷质量分数的增加先升高后降低再升高;而在高质量浓度镉（Cd30）条件下,土壤对镉的吸附量随磷质量分数的增加逐渐升高,在相同磷水平下,随外加锌质量浓度的增加,镉的吸附量明显降低,而解吸量则逐渐升高。不同秸秆量土壤对不同质量浓度镉吸附解吸时,在Cd3条件下,土壤对镉的吸附量随秸秆加入量的增加先升高后降低,而在同一质量分数磷情况下,吸附量逐渐下降;土壤对镉的解吸量在磷质量分数为120 mg·kg^-1（P2）时最低,而后随着磷质量分数的增加而增加。在同一质量分数磷水平情况下,随着秸秆添加量的增加,土壤对镉的解吸量逐渐增加。而在Cd30条件下,土壤对镉的吸附量逐渐增加,在同一磷水平情况下,土壤对镉的吸附情况是低量秸秆（C1）〉高量秸秆（C2）,但在磷质量分数为240 mg·kg^-1（P3）水平下,不添加秸秆（C0）情况时镉的吸附量最大,而后降低。土壤对镉的解吸量随着磷含量的增加而增加。在同一磷水平情况下,随着秸秆添加量的增加,土壤对镉的解吸量逐渐增加。     

焚烧炉飞灰熔融处理组成特性分析

将焚烧飞灰在不同温度下进行熔融实验，用扫描电镜对熔融前后试样的微观结构和形貌变化进行比较，结果显示：熔融体表观结构平整光滑，有较高的硬度，其断面有光泽产生且无明显气孔，试样已达到完全熔融；用X射线衍射分析仪对试样熔融前后成分的变化进行分析，未经熔融处理的试样主要晶相为：NaCl，KCl，SiO2，CaCO3，CaSO4，Ca2SiO4以及Ca12Al14O33，CaS和钙黄长石为熔融后试样的主要晶相．其次还有CaO和透灰石；浸出实验结果显示熔融处理后飞灰的毒性得到降解．     

A new method to inertize incinerator toxic fly ash with silica from rice husk ash

Fly ash from municipal solid waste incineration is a toxic waste due to the presence of toxic heavy metals. Here, a new method for metal stabilization based on the use of silica gel extracted from rice husk ash is presented. This method is sustainable because of the use of only waste materials to produce a final inert product, and because the inertization procedure occurs at room temperature. The estimated maximum Pb adsorption capacity of extracted silica, of about 36 mg/g, is found to be far greater than the adsorption capacity of other known absorbers used for municipal solid waste incineration fly ash.     

Research on low emission MSW gasification and melting system

In order to eliminate secondary pollution caused by municipal solid waste (MSW) incineration, a MSW gasification and melting process is proposed. The process is expected to reduce the emission of pollutants, especially heavy-metals and dioxins. In this paper, the combustible components of MSW and simulated MSW were gasified in a lab-scale fluidized bed at 400°C–700°C when the excess air ratio (ER) was between 0.2 and 0.8. The experimental results indicated that the MSW could be gasified effectively in a fluidized bed at approximately 600°C–700°C when excess air ratio was 0.2–0.4. The melting characteristics of two typical fly ash samples from MSW incinerators were investigated. The results indicated that fly ash of pure MSW incineration could be melted at approximately 1,300°C and that of MSW and coal co-combustion could be melted at approximately 1,400°C. When temperature was over 1,100°C, more than 99.9% of the dioxins could be decomposed and most of the heavy-metals could be solidified in the slag. Based on the above experiments, two feasible MSW gasification and melting processes were proposed for low calorific value MSW: (1) sieved MSW gasification and melting system, which was based on an idea of multi-recycle; (2) gasification and melting scheme of MSW adding coal as assistant fuel.     

Review of fly ash inertisation treatments and recycling

Fly ash (FA) is a by-product of power, and incineration plants operated either on coal and biomass, or on municipal solid waste. FA can be divided into coal fly ash, obtained from power plant burning coal, flue gas desulphurisation FA, that is, the by-product generated by the air pollution control equipment in coal-fired power plants to reduce the release of SO₂, biomass FA produced in the plants for thermal conversion of biomass and municipal solid waste incineration (MSWI) FA, that is, the finest residue obtained from the scrubber system in a MSWI plant. Because of the large amount produced in the world, fly ash is now considered the world’s fifth largest material resource. The composition of FA is very variable, depending on its origins; then, also pollutants can be very different. In this frame, it is fundamental to exploit the chemical or physical potentials of FA constituents, thus rendering them second-life functionality. This review paper is addressed to FA typology, composition, treatment, recycling, functional reuse and metal and organic pollutants abatement. Because of the general growing of environmental awareness and increasing energy and material demand, it is expected that increasing recycling rates will reduce the pressure on demand for primary raw materials, help to reuse valuable materials which would otherwise be wasted and reduce energy consumption and greenhouse gas emissions from extraction and processing.     

Development and prospects of municipal solid waste (MSW) incineration in China

With the lack of space for new landfills, municipal solid waste (MSW) incineration is playing an increasingly important role in municipal solid waste management in China. The literatures on certain aspects of incineration plants in China are reviewed in this paper, including the development and status of the application of MSW incineration technologies, the treatment of leachate from stored MSW, air pollution control technologies, and the status of the fly-ash control method. Energy policy and its promotion of MSW-to-energy conversion are also elucidated.     

Levels and patterns of polychlorinated biphenyls in residues from incineration of established source-classified MSW in China

Municipal solid waste (MSW) source-classified collection represents an advancement in resource cycling and secondary pollution control in China. Comparative experiments were performed to assess the levels and patterns of polychlorinated biphenyls in bottom ash, fly ash from boiler, and fly ash from bag filter from an MSW incineration plant with source-classified collection of MSW. Polychlorinated biphenyls were concentrated in the bag filter fly ash and in the bottom ash. The total amount of polychlorinated biphenyls was much lower than in fly ashes and bottom ash from traditional mixed waste incineration. Total concentration of coplanar polychlorinated biphenyls and toxic equivalent quantities were also reduced. Due to variations of feed waste, complete combustion, including continuously high incineration temperature, low CO concentrations and high air excess ratio were observed. Incineration temperature showed a negative correlation, while CO concentration showed a positive correlation with total and coplanar polychlorinated biphenyls, indicating that the latter can be reduced by controlling combustion conditions related to properties of feed waste.     

A steam dried municipal solid waste gasification and melting process

Considering high-moisture municipal solid waste (MSW) of China, a steam dried MSW gasification and melting process was proposed, the feasibility was tested, and the mass and energy balance was analyzed. Preliminary experiments were conducted using a fixed-bed drying apparatus, a 200 kg per day fluidized-bed gasifier, and a swirl melting furnace. Moisture percentage was reduced from 50% to 20% roughly when MSW was dried by slightly superheated steam of 150°C?C350°C within 40 min. When the temperature was less than 250°C, no incondensable gas was produced during the drying process. The gasifier ran at 550°C?C700°Cwith an air equivalence ratio (ER) of 0.2?C0.4. The temperature of the swirl melting furnace reached about 1240°C when the gasification ER was 0.3 and the total ER was 1.1. At these conditions, the fly ash concentration in the flue gas was 1.7 g·(Nm³)^?1, which meant over 95% fly ash was trapped in the furnace and discharged as slag. 85% of Ni and Cr were bound in the slag, as well as 60% of Cu. The mass and energy balance analysis indicates that the boiler heat efficiency of an industrial MSW incineration plant reaches 86.97% when MSW is dried by steam of 200°C. The boiler heat efficiency is sensitive to three important parameters, including the temperature of preheated MSW, the moisture percentage of dried MS Wand the fly ash percentage in the total ash.     

复杂环境样品中未知组分峰的跟踪识别方法

以垃圾焚烧飞灰中的持久性组分分析为例,研究了不同程序升温条件下用于峰识别的拟合定量方法.通过不同程序升温条件下气相色谱拟合峰的准确保留时间,计算色谱峰的保留参数,并预测任意柱温条件下的保留时间.通过与实验值的对比证明预测结果是准确的.     

PCDD/DFs and coplanar PCBs in fly ash samples from various types of incinerators in Taiwan

Polychlorinated dibenzo‐p‐dioxins and dibenzofurans (PCDD/DFs) and coplanar polychlorinated biphenyls (Co‐PCBs) were determined in fly ash samples from municipal solid waste (MSW), medical waste (MW), and electricity power plant incinerators in Taiwan. The average concentrations of PCDD/DFs and Co‐PCBs are 7.02 ng‐TEQ/g and 1.06 ng‐TEQ/g, respectively. The contributions to total TEQ are 24% from PCDDs, 64% from PCDFs, and 12% from Co‐PCBs, indicating that PCDFs generate the highest environmental impact and MSW and MW incinerators are potential Co‐PCBs contaminating sources. The levels of PCDD/DFs and Co‐PCBs found in ash samples increase from petroleum‐fired, coal‐fired, large municipal solid waste, small medical waste, to small municipal solid waste incinerators, and are generally lower than those from incinerators built earlier. All fly ash samples analyzed in this study were considered hazardous materials. More research is suggested to establish the relationship between the amounts of PCDD/DFs and Co‐PCBs in fly ash and in flue gas.     

城市生活垃圾焚烧厂设计方案研究

本文章简要介绍了城市生活垃圾焚烧厂工艺参数、炉型结构、烟气处理、用地面积、设备配置、环境保护、工程投资和运行成本等内容的选择原则和设计方案。