上海郊区小型沼气发展的前景与方向

文章介绍了上海郊区沼气开发利用的发展历程和现状,分析了上海沼气发展萎缩的原因,指出上海在节能减排的大形势、寻找合理的农村生活垃圾处理出路和解决小型禽畜养殖场的环境问题等压力下,对郊区的沼气发展产生了新的需求。而以小型养殖场为中心、吸纳农村有机生活垃圾的小型沼气系统则是上海郊区未来沼气发展的方向,也是新农村环境整治的可行途径。     

Performance assessment of integrated energy systems for HVAC applications

In this article, energy and exergy analyses are conducted for two integrated systems which can be used in HVAC applications. These two systems are analyzed for the cases of single generation, cogeneration and trigeneration, and their performances are evaluated through energy and exergy efficiencies. The parametric studies are performed to investigate the effects of using cogeneration and extended to trigeneration on the system performance. To perform the comparisons between the systems for multiple options, the same amounts of outputs (in terms of electricity, heating, cooling) are produced for all systems. The energy analyses of systems 1 and 2 show a great benefit for moving from single generation to trigeneration, with the trigeneration efficiencies of 83.5% and 87.2%, respectively, and single generation efficiencies of 47% for both systems. However, the exergy analyses show that trigeneration may not always become more efficient than single generation, particularly for system 1, due to the fact that the trigeneration exergy efficiency is 38.7% and the corresponding single generation efficiency is 44.3%. For system 2, the trigeneration exergy efficiency is 52.7% while the single generation efficiency becomes 44.3%. Depending on the type of cogeneration or cogeneration design, the system can be more efficient.     

Drying of salted silver jewfish in a hybrid solar drying system and under open sun: Modeling and performance analyses

This study investigated the thin-layer drying kinetics of salted silver jewfish in a hybrid solar drying system and under open sun. Ten drying models were compared with experimental data of salted silver jewfish drying. A new model was introduced, which is an offset linear logarithmic (offset modified Page model). The fit quality of the models was evaluated using the coefficient of determination (R²), root mean square error (RMSE), and sum of squared absolute error (SSAE). The result showed that Midilli et al. model and new model were comparable with two or three-term exponential drying models. This study also analyzed energy and exergy during solar drying of salted silver jewfish. Energy analysis throughout the solar drying process was estimated on the basis of the first law of thermodynamics, whereas exergy analysis during solar drying was determined on the basis of the second law of thermodynamics. At an average solar radiation of 540 W/m² and a mass flow rate of 0.0778 kg/sec, the collector efficiency and drying system efficiency were about 41% and 23%, respectively. Specific energy consumption was 2.92 kWh/kg. Moreover, the exergy efficiency during solar drying process ranged from 17% to 44%, with an average value of 31%. The values of improvement potential varied between 106 and 436 W, with an average of 236 W.     

Second Law Analysis for Solar Cookers

Abstract

This article presents the importance and usefulness of Second Law (exergy) analysis for evaluating and comparing solar cookers in meaningful ways. The thermodynamic considerations required for the development of rational and meaningful methodologies for the evaluation and comparison of the efficiency of the solar cookers were defined. Energy and exergy equations were also developed to obtain energy and exergy efficiencies of the solar cookers. The evaluation of the solar cookers requires a measure of efficiency, which is rational, meaningful, and practical. Exergy analysis provides an alternative means of evaluating and comparing the solar cookers. Since exergy is a measure of the quality or usefulness of energy, exergy efficiency measures are more significant than energy efficiency measures, exergy analysis should be considered in the evaluation of the solar cookers.     

Energy and exergy analysis of a heat storage tank with a novel eutectic phase change material layer of a solar heater system

Solar energy is one of the most important renewable energy sources, but it is not available every time and every season. Thus, storing of solar energy is important. One of the popular methods of heat storage is use of phase change materials (PCMs) which have large thermal energy storage capacity. In this study, the heat storage tank in a domestic solar water heating system was chosen as control volume. The experiments were performed in the province of Elaz?g, Turkey, in November when solar radiation was weak due to cloudy sky. The heat storage tank of the system was modified to fill PCM between insulation and hot water part. A few PCMs which are Potassium Fluoride, Lithium Metaborate Dihydrate, Strontium Hydroxide Octahydrate, Barium Hydroxide Octahydrate, Aluminum Ammonium Sulfate, and Sodium Hydrogen Phosphate were analyzed to proper operating conditions using a Differential Scanning Calorimeter (DSC) and the best PCM was obtained with the Aluminum Ammonium Sulfate and Sodium Hydrogen Phosphate mixture. Thus, eutectic PCM was obtained and used in a heat storage tank of the solar water heating system. Energy and exergy analysis of heat storage tank was performed with and without the PCM. Energy and exergy analysis has shown that the heat storage tank with the PCM is more efficient than without the PCM and the maximum exergy efficiency was obtained as 22% with the heat storage tank with the PCM.     

Resource conservation in the pulp and paper industries—rational-use-of-energy approach

Sharp rises in energy prices have generated an interest in the pulp and paper industries in cogeneration and heat pump applications. However, the institutional and industry-specific barriers to their implementation, despite economic viability, indicate the inadequacies of the energy conservation and energy saving approaches to minimise energy costs. A systems approach, referred to as rational-use-of-energy, is proposed to overcome some of the barriers and to highlight the conservation potential of other resources, such as chemicals and water at appreciably low effluent loads.     

A Parametric Study of a Piston-Prop Aircraft Engine Using Exergy and Exergoeconomic Analysis Methods

In this study, exergetic and exergoeconomic analysis methods are applied to a four-cylinder, spark ignition (SI), naturally aspirated and air-cooled piston-prop aircraft engine in the cruise phase of flight operations. The duration of cruise is selected to be 1 h. Three parameters, altitude, rated power setting (PS), and air-to-fuel ratio (AF), are varied by the calculation of the max–min values of exergy analysis. Based on the results of energy analysis, the values for the maximum energy efficiency and fuel consumption flow rate are calculated to be 21.73% and 28.02 kg/h, respectively, at 1000-m altitude and 75% PS. The results of exergy analysis indicate that all exergetic values vary from 65% to 75% PS, while this increase is not seen in exergoeconomic analysis. While the maximum exergy input rate is obtained to be 405.60 kW, exergy efficiency has the minimum value with 14.43% and exergy destruction rate has the maximum value with 168.48 kW. These values are achieved at 3000-m altitude and 18 AFs. The maximum average exergy cost of the fuel is calculated to be 130.77 $/GJ at 1000-m altitude, 13 AF ratios, and 65% PS. At this point, while the minimum cost rate associated with the exergy destruction is obtained to be 40.29 $/h, the maximum exergoeconomic factor is found to be 19.98%.     

Assessment of the overall resource consumption of germanium wafer production for high concentration photovoltaics

The overall resource requirements for the production of germanium wafers for III–V multi-junction solar cells applied in concentrator photovoltaics have been assessed based on up to date process information. By employing the cumulative energy demand (CED) method and the cumulative exergy extraction from the natural environment (CEENE) method the following resources have been included in the assessment: fossil resources, nuclear resources, renewable resources, land resources, atmospheric resources, metal resources, mineral resources and water resources. The CED has been determined as 216 MJ and the CEENE has been determined as 258 MJ_ex. In addition partial energy and exergy payback times have been calculated for the base case, which entails the installation of the high concentration photovoltaics (HCPVs) in the Southwestern USA, resulting in payback times of around 4 days for the germanium wafer production. Due to applying concentration technology the germanium wafer accounts for only 3% of the overall resource consumption of an HCPV system. A scenario analysis on the electricity input to the wafer production and on the country of installation of the HCPV has been performed, showing the importance of these factors on the cumulative resource consumption of the wafer production and the partial payback times.     

Theoretical Calculation and Economic Assessment of the Integrated Solar Combined Cycle Power Plants

The ISCC technology representing an integrated solar combined cycle and the economic assessment of ISCC are investigated. Comparisons conducted by theoretical calculation method among two cases, that is, an integrated solar combined cycle system (ISCCS) and a combined cycle gas turbine system (CCGTS) show that ISCCS provides the best solution with the highest efficiency of heat to electricity among them. The results reflected by theoretical calculation also reveal that ISCCS is beneficial to energy saving and emission reduction. Due to the great advantages of ISCC, comprehensive analysis on the basic conditions for building ISCC power plants is analyzed in detail.     

Potential of solar domestic hot water systems in rural areas for greenhouse gas emission reduction in Poland

Application of solar energy for preparing domestic hot water is one of the easiest methods of utilization of this energy. At least part of the needs for warm tap water could be covered by solar systems. At present, mainly coal is used for water heating at dwellings in rural areas in Poland. Warm tap water consumption will increase significantly in the future as standards of living are improved. This can result in the growth of electricity use and an increase in primary fuel consumption. Present and future methods of warm sanitary water generation in rural areas in Poland is discussed, and associated greenhouse gas (GHG) emissions are estimated. It is predicted that the emission of CO₂ and NOx will increase. The emission of CO and CH₄ will decrease because of changes in the structure of the final energy carriers used. The economic and market potentials of solar energy for preparing warm water in rural areas are discussed. It is estimated that solar systems can meet 30%–45% of the energy demand for warm water generation in rural areas at a reasonable cost, with a corresponding CO₂ emission reduction. The rate of realization of the economic potential of solar water heaters depends on subsidies for the installation of equipment.

     

Energy,exergy analysis,and sustainability assessment of different engine powers for helicopter engines

The rapid decrease of energy resources has accelerated studies on energy efficiency. Energy efficiency refers to the effective use of energy, in other words, completing a specific task to the required standard by using less energy. Exergy is an effective instrument to indicate the effective and sustainable use of energy in systems and processes. Transportation is an important part of human life. The studies on energy saving and the effective use of energy in different areas around the world have also increased for transportation systems and vehicles. With the more effective use of fuel, there will be potential benefits for the environment as well as a reduction in operating costs. This study includes energy and exergy analyses as well as a sustainability assessment by using C₈H₁₆ as a fuel at different engine powers (150–600 SHP (shaft horse power)), for the piston-prop helicopter engine. The maximum exergetic sustainability index was found at the power that provided the maximum energy and exergy efficiency. As a result of this index, the lowest waste exergy ratio, the lowest exergy destruction factor, and the lowest environmental impact factor were obtained. The highest exergy destruction and the highest exergy loss value were obtained at maximum power (600 SHP).     

新型固硫节煤剂在供热锅炉系统中的应用

长庆油田矿区服务事业部各生活小区锅炉90%的能源用于小区采暖供热,锅炉供热能耗大,效率低。为降低供热能耗,2012年1月对庆城基地锅炉系统中的SZL14--1.0/95/70型号锅炉使用固硫节煤剂的应用效果进行了现场试验对比。试验证明:通过添加新型固硫节煤剂能改善炉膛燃烧氛围、促进燃烧完全,降低炉渣含碳量,提高热效率7%,节煤率12%。同时,固硫效果明显,烟尘排放CO、SO2明显减少。     

热联合在塔西南化肥厂节能降耗的应用

通过优化塔西南化肥厂合成氨装置的蒸汽系统和电力工程部的锅炉运行模式,新增外购4.2MPa蒸汽用量,在实现快装锅炉停运的同时送出富余的1.6MPa蒸汽,达到能源梯级循环利用,从而为自身装置和厂际间共同实现节能降耗进行了有益探索,并取得可观的经济效益和社会效益。     

Experimental investigation of a 250-kW turbine organic Rankine cycle system for low-grade waste heat recovery

An organic Rankine cycle (ORC) is generally used for converting low-grade heat into electricity. In this study, an extensive literature survey was conducted to identify current research gaps on experimental ORC systems. Specifically, there is limited experimental data and limited details on thermal and expander efficiencies of ORC systems. In order to address these gaps, the objective of this study included developing a turbine ORC with a power output exceeding 50 kW and thermal efficiency exceeding 8% for a heat source temperature < 120°C. The experimental results indicated that the system achieved a net power output of 242.5 kW and a thermal efficiency of 8.3% (the highest value for a turbine ORC system for the heat source temperature below 120°C). Thus, the study addressed the gaps identified in the research area of ORCs.     

Thermal analysis of tilted wick solar distillation-cum-drying system

The performance of the designed tilted wick solar water distillation-cum-drying unit has been tested at water flow rates of 50 and 65 ml/min in the distillation unit. Effect of water flow rates on the heat transfer coefficients of distillation and drying unit for drying ginger has been evaluated. The energy and exergy efficiency of the distillation system have also been evaluated. Average distillates of 2.36 and 2.2 l/m² were collected from the tilted wick solar still at flow rates of 50 and 65 ml/min, respectively. Large variation in convective and evaporative heat transfer coefficients of distillation unit has been observed at given water flow rates. Water flow rate in the distillation unit significantly affects the performance of the drying unit. Average convective heat transfer coefficients of 6.56 and 3.75 W/m^{2 o}C have been observed for drying ginger at flow rates of 50 and 65 ml/min, respectively. Energy and exergy efficiency of the distillation unit have been found to be nearly 19% and 0.9%, respectively. Experimental uncertainty has also been evaluated for distillation and drying units. The distillate cost for the developed distillation-cum-drying unit is calculated as $0.03729/l along with dried ginger of about 2.5 kg/m²/day.     

锅炉燃煤的最佳方式

从节能、环保、资源开发并重并举的高度,探讨了锅炉燃煤的最佳方式和技术经济的可行性,认为先热解后燃烧,特别是以廉价氢源进行加氢热解后再燃烧是锅炉燃煤的最佳方式。     

Effect of Fenton pretreatment on anaerobic digestion of olive mill wastewater and olive mill solid waste in mesophilic conditions

The olive mill waste (OMW) generated from olive oil extraction process constitutes a major environmental concern owing to its high organic and mineral matters and acidic pH. Anaerobic digestion (AD) is a main treatment for reducing the organic matter and toxic substances contained in OMW and generating at the same time, energy in the form of biogas. AD of OMW that contains lignocellulose is limited by the rate of hydrolysis due to their recalcitrant structure. This study is devoted to the effect of Fenton process (FP) pretreatment on olive mill wastewater (OMSW) /olive mill solid waste (OMWW) co-digestion to improve their digestibility and in this way the biogas production. The FP pretreatment was performed in batch mode at 25°C, various H₂O₂/[Fe²⁺] ratios (100–1200), catalyst concentration ([Fe²⁺]) ranging from 0.25 to 2 mM, reaction time varying from 30 to150 min, and different pH (3–11). The best performance was obtained with H₂O₂/[Fe²⁺] = 1000, [Fe²⁺] = 1.5 mM, 120 min, and pH 3. Biochemical methane potential (BMP) tests conducted in batch wise digester and at mesophilic conditions (37 °C) showed that cumulative biogas and methane production were higher without FP treatment, and correspond to 699 and 416 mL/g VS, respectively. However, pre-treated OMSW results into an increase of 24% of methane yield. After 30 days of AD, the methane yield was 63%, 54%, and 48%, respectively, for OMSW treated without iron precipitation, with iron precipitation and untreated OMSW sample.     

Techno-economic analysis and environmental impact assessment of energy recovery from Municipal Solid Waste (MSW) in Brazil

Due to the lack of appropriate policies in the last decades, 60% of Brazilian cities still dump their waste in non-regulated landfills (the remaining ones dump their trash in regulated landfills), which represent a serious environmental and social problem. The key objective of this study is to compare, from a techno-economic and environmental point of view, different alternatives to the energy recovery from the Municipal Solid Waste (MSW) generated in Brazilian cities. The environmental analysis was carried out using current data collected in Betim, a 450,000 inhabitants city that currently produces 200 tonnes of MSW/day. Four scenarios were designed, whose environmental behaviour were studied applying the Life Cycle Assessment (LCA) methodology, in accordance with the ISO 14040 and ISO 14044 standards. The results show the landfill systems as the worst waste management option and that a significant environmental savings is achieved when a wasted energy recovery is done. The best option, which presented the best performance based on considered indicators, is the direct combustion of waste as fuel for electricity generation. The study also includes a techno-economical evaluation of the options, using a developed computer simulation tool. The economic indicators of an MSW energy recovery project were calculated. The selected methodology allows to calculate the energy content of the MSW and the CH₄ generated by the landfill, the costs and incomes associated with the energy recovery, the sales of electricity and carbon credits from the Clean Development Mechanism (CDM). The studies were based on urban centres of 100,000, 500,000 and 1,000,000 inhabitants, using the MSW characteristics of the metropolitan region of Belo Horizonte. Two alternatives to recovering waste energy were analyzed: a landfill that used landfill biogas to generate electricity through generator modules and a Waste-to-Energy (WtE) facility also with electricity generation. The results show that power generation projects using landfill biogas in Brazil strongly depend on the existence of a market for emissions reduction credits. The WtE plant projects, due to its high installation, Operation and Maintenance (O&M) costs, are highly dependent on MSW treatment fees. And they still rely on an increase of three times the city taxes to become attractive.     

DDNP废水处理新方法研究

DDNP是一种重要的起爆药，其生产废水成份复杂，用传统工艺处理难度较大且不经济。鉴于此，经研究总结得出DDNP废水处理新工艺：先用锅炉废烟气蒸发浓缩，再焚烧的方法，即处理了废水，又降低了锅炉烟尘。是一种低成本、低能耗以废治废的经济实用方法。