大客车正面碰撞乘客约束系统仿真分析

为探究约束系统在全承载客车正面碰撞事故中对乘客损伤的影响,利用有限元分析软件LS_DYNA建立某大客车正面碰撞仿真模型,并开展整车50 km/h正面100％重叠碰撞固定刚性壁障试验;从车身变形、加速度曲线和乘员损伤等3方面验证仿真模型;基于已验证的仿真模型,开展不同座椅间距、车厢位置及安全带类型的乘员运动响应和损伤等综...     

Effects of initial seated position in low speed rear-end impacts: a comparison with the TNO rear impact dummy (TRID) model

Injury-producing mechanisms associated with rear-end impact collision has remained a mystery not withstanding numerous investigations devoted to its scrutiny. Several criteria have been proposed to predict the injury-causing mechanism, but none have been universally accepted. The challenge lies in determining a set of testing procedures representative of real-world collisions, wherein the results obtained are not only the same as human testing, but remain consistent with various subjects and impact conditions. It is hypothesized that one of the most important considerations in the testing methodology is the effect of initial seated position (ISP) on occupant kinematics during a rear impact collision. This study involves two parts that evaluates the effects of ISP during rear-end impact. In the first part, head acceleration results of computer simulation using Hybrid III TNO rear impact dummy (TRID) are compared to physical impact testing (PIT) of humans. The second part focuses on the computer simulation using TRID to obtain different neck parameters such as NIC (Neck Injury Criterion), NIJ (Neck Injury Predictor), neck forces and moments to predict the level of neck injury such as whiplash associated disorder (WAD) during low speed rear-end impact. In PIT, a total of 17 rear-impact tests were conducted with a nominal 8-km/hour change in velocity to 5 subjects in four different seated positions comprising of a normal position (NP) and three out of positions (OOP). The first position was a NP, defined as torso against the seat back, looking straight ahead, hands on the steering wheel, and feet on the floor. The second position was a head flex position (HFP), defined as the normal position with head flexed forward approximately 20 degrees. The third position was a torso lean position (TLP), defined as the normal position with torso leaned forward approximately 10 degrees away from the seat back. Lastly, a torso lean head flex position (TLHFP), defined as the normal position with the head flexed forward approximately 20 degrees and torso leaned forward approximately 10 degrees. The head acceleration plots from PIT reveal that for the third and fourth positions (TLP and TLHFP) when the subject torso leaned forward, the peak head acceleration for the subject decreased and there was also a delay in reaching the peak. The Hybrid III-TRID anthropomorphic test dummy (ATD) was used in the same four different seated positions using computer simulation software MAthematical DYnamic MOdel (MADYMO 6.0) and the head acceleration results were compared to PIT. The comparison demonstrates that the Hybrid III-TRID ATD with MADYMO can be a reliable testing procedure during low-speed, rear-end impact for the four ISPs considered since the head acceleration plots deviated within the range of PIT head acceleration plots for different human subjects. This ensures that the second part of the study with neck injury using computer simulation results is a reliable testing procedure. It can be observed that MADYMO results have a greater error when compared to PIT when more than one OOP condition is employed as in TLHFP. All these observations would help in providing a tool to better understand the injury mechanisms and provide an accurate testing procedure for rear-end impact.     

Injury risk in behind armor blunt thoracic trauma.

First responders and military personnel are particularly susceptible to behind armor blunt thoracic trauma in occupational scenarios. The objective of this study was to develop an armored thorax injury risk criterion for short duration ballistic impacts. 9 cadavers and 2 anthropomorphic test dummies (AUSMAN and NIJ 0101.04 surrogate) were tested over a range of velocities encompassing low severity impacts, medium severity impacts, and high severity impacts based upon risk of sternal fracture. Thoracic injuries ranged from minor skin abrasions (abbreviated injury scale [AIS] 1) to severe sternal fractures (AIS 3+) and were well correlated with impact velocity and bone mineral density. 8 male cadavers were used in the injury risk criterion development. A 50% risk of AIS 3+ injury corresponded to a peak impact force of 24,900 +/- 1,400 N. The AUSMAN impact force correlated strongly with impact velocity. Recommendations to improve the biofidelity of the AUSMAN include implementing more realistic viscera and decreasing the skin thickness.     

Effect of posture on forces and moments measured in a Hybrid III ATD lower leg

Objective: Anthropomorphic test devices (ATDs) are used to assess real injury risk to occupants of vehicles during injurious events. In the lower leg, values from load cells are compared to injury criteria developed in cadaveric studies. These criteria are typically developed with the leg in a neutral posture, whereas the ATD may assume a wide range of postures during safety evaluation tests. The degree to which the initial posture of an ATD has an effect on the measured forces and moments in the lower leg is unknown.

Methods: A Hybrid III ATD lower leg was impacted in a range of postures under conditions representing a crash test, and peak axial force and adjusted tibia index injury measures were evaluated. Ankle posture was varied in 5° increments using a custom-made footplate, and dorsi/plantarflexion (20° DF to 20° PF) and in/eversion (20° IV to 5° EV) were evaluated. Tibia angle was also varied (representing knee flexion/extension) by ±10° from neutral.

Results: Peak axial force was not affected by ankle flexion or tibia angulation. Adjusted tibia index was lowest for plantarflexion, as well as for tibia angles representative of knee extension. Both peak axial force and adjusted tibia index were lowest for postures of great inversion and were highest in neutral or near-neutral postures.

Conclusions: The range of postures tested herein spanned published injury criteria and thus would have made the difference between pass and fail in a safety evaluation. In/eversion had the largest influence on injury metrics, likely due to the change in axial stiffness and altered impact durations in these postures. Results suggest increased injury risk at neutral or near-neutral postures, whereas previous cadaveric studies have suggested that in/eversion does not influence injury risk. It is unclear whether the ATD appropriately represents the natural lower leg for impacts in out-of-position testing. Great care must be taken when initially positioning ATDs for safety evaluations, because small perturbations in posture were shown herein to have large effects on the measured injury risk using this tool.     

Evaluation of pedestrian subsystem test method using legform and upper legform impactors for assessment of high-bumper vehicle aggressiveness

In accidents involving sports utility vehicles (SUVs), injuries to pedestrian leg, knee ligaments, and femur are likely to occur. Therefore, the European Enhanced Vehicle Safety Committee proposed two subsystem test methods for evaluation of SUV bumper aggressiveness. Such evaluation can be conducted by means of either a legform impactor (evaluation of risk of knee and tibia injury), or an upper legform impactor (evaluation of risk of thigh and pelvis injury) test. Each of these two test methods has its own injury criteria and injury acceptance levels. Therefore, the first objective of this research is to clarify any differences between the test results obtained when evaluating SUV bumper aggressiveness by means of these two impactors. The second objective is to determine whether or not a legform impactor can be applied to estimate the risk of femur fracture, and if an upper legform impactor can be used to estimate the risk of knee ligament injury. The present results indicate the test method using an upper legform impactor yields higher ratios of injury criteria to the relevant EEVC/WG17 injury acceptance levels than by using a legform impactor. Thus, the upper legform impactor test rates an SUV bumper as more aggressive than the legform impactor test. The present study suggests the lower leg acceleration obtained by the legform impactor can be used to adequately assess the risk of femur fracture, when evaluating the aggressiveness of an SUV bumper using proposed injury acceptance levels reported in the literature. Similarly, the impact force obtained by the upper legform impactor can be used to assess the risk of cruciate ligament injury.     

Rear impact responses of different sized adult Hybrid III dummies

Rear impact sled tests were conducted using 5th, 50th, and 95th percentile Hybrid III dummies to evaluate proposed injury criteria. Different head restraint height (750, 800 mm) and backset (0, 50, 100 mm) positions were used to determine axial and shear forces, bending moments, and injury criteria (NIC, N(ij), and N(km)). The time sequence to attain each parameter was also determined. Three events were identified in the response. Event I was coincident with the maximum rearward motion of the torso, Event II occurred at the time of the peak upper neck flexion moment, and Event III occurred at the time of maximum rearward motion of the head. Parameters such as backset, head restraint height, seat-head restraint interaction, and anthropometry affected impact responses. Head rotations increased with increasing backset and increasing head restraint height. However, N(ij) and N(km) did not exhibit such clear trends. The 50th percentile dummy responded with consistent injury criteria values (e.g., the magnitude of the injury criteria increased with backset increase or head restraint height decrease). However, the 5th and 95th percentile dummies did not demonstrate such trends. These findings underscore the need to include subject anthropometry in addition to seat and head restraint characteristics for better assessment of rear impact responses.     

Lower Leg Injury Reference Values and Risk Curves from Survival Analysis for Male and Female Dummies: Meta-analysis of Postmortem Human Subject Tests

Objective: Derive lower leg injury risk functions using survival analysis and determine injury reference values (IRV) applicable to human mid-size male and small-size female anthropometries by conducting a meta-analysis of experimental data from different studies under axial impact loading to the foot–ankle–leg complex.

Methods: Specimen-specific dynamic peak force, age, total body mass, and injury data were obtained from tests conducted by applying the external load to the dorsal surface of the foot of postmortem human subject (PMHS) foot–ankle–leg preparations. Calcaneus and/or tibia injuries, alone or in combination and with/without involvement of adjacent articular complexes, were included in the injury group. Injury and noninjury tests were included. Maximum axial loads recorded by a load cell attached to the proximal end of the preparation were used. Data were analyzed by treating force as the primary variable. Age was considered as the covariate. Data were censored based on the number of tests conducted on each specimen and whether it remained intact or sustained injury; that is, right, left, and interval censoring. The best fits from different distributions were based on the Akaike information criterion; mean and plus and minus 95% confidence intervals were obtained; and normalized confidence interval sizes (quality indices) were determined at 5, 10, 25, and 50% risk levels. The normalization was based on the mean curve. Using human-equivalent age as 45 years, data were normalized and risk curves were developed for the 50th and 5th percentile human size of the dummies.

Results: Out of the available 114 tests (76 fracture and 38 no injury) from 5 groups of experiments, survival analysis was carried out using 3 groups consisting of 62 tests (35 fracture and 27 no injury). Peak forces associated with 4 specific risk levels at 25, 45, and 65 years of age are given along with probability curves (mean and plus and minus 95% confidence intervals) for PMHS and normalized data applicable to male and female dummies. Quality indices increased (less tightness-of-fit) with decreasing age and risk level for all age groups and these data are given for all chosen risk levels.

Conclusions: These PMHS-based probability distributions at different ages using information from different groups of researchers constituting the largest body of data can be used as human tolerances to lower leg injury from axial loading. Decreasing quality indices (increasing index value) at lower probabilities suggest the need for additional tests. The anthropometry-specific mid-size male and small-size female mean human risk curves along with plus and minus 95% confidence intervals from survival analysis and associated IRV data can be used as a first step in studies aimed at advancing occupant safety in automotive and other environments.     

Assessing the performance of motorcyclists’ impact protectors in simulated ATD knee and shoulder impacts

Objective: Fractures are a common injury among motorcycle riders and can have serious health implications. Impact protection (IP) has been designed to help prevent fractures, yet there are conflicting opinions as to whether this IP does in fact help prevent fractures in real-world crashes. This work aimed to (1) use simulated dummy impacts to examine whether existing types of IP could reduce the force transferred to the underlying bone to below fracture tolerance levels and (2) investigate whether current European Standard (EN 1621-1) test procedures for impact protectors designed for motorcyclists are sufficient to ensure fracture protection.

Method: Twenty-three shoulder and 7 knee IP specimens were tested using a 23-kg impactor contacting axially along the clavicle and femur of an anthropomorphic test device (ATD) at an energy level corresponding to the fracture tolerance of these bones. Sixteen IP specimens were the same as those worn by motorcycle riders involved in crashes where injury outcome was known (knee: n?=?3; shoulder: n?=?13) and the IP had been previously tested to EN 1621-1. Other IP tested represented a wide range of IP available for purchase at a motorcycle accessory store. Double and triple layers of IP were also tested. Energy attenuated during the dummy impacts was compared to energy attenuated when tested to EN 1621-1.

Results: Of the 23 shoulder IP tested, the average percentage reduction of transferred force to the shoulder from the baseline test was 7.6?±?4.8%. The percentage reduction of transferred force to the knee from the baseline was 43.9?±?7.5%. The entire group of knee IP tested reduced the transferred force to the knee to below the 10-kN injury threshold for the femur. There was a positive but nonsignificant correlation between the ATD test and the EN 1621-1 impact test performance, suggesting that the European standard test method likely provides a good indication of IP performance. However, given the low correlation coefficient, the relationship between IP performance in the European standard test method and injury protection remains unclear.

Conclusion: Though the energy attenuation test method in the European standard may be an appropriate approach, distinct differences in injury protection performance observed between knee and shoulder IP indicate that there may be a need for different performance criteria for IP designated to protect different body regions.     

Driver Injury Risk Variability in Finite Element Reconstructions of Crash Injury Research and Engineering Network (CIREN) Frontal Motor Vehicle Crashes

Objective: A 3-phase real-world motor vehicle crash (MVC) reconstruction method was developed to analyze injury variability as a function of precrash occupant position for 2 full-frontal Crash Injury Research and Engineering Network (CIREN) cases.

Method: Phase I: A finite element (FE) simplified vehicle model (SVM) was developed and tuned to mimic the frontal crash characteristics of the CIREN case vehicle (Camry or Cobalt) using frontal New Car Assessment Program (NCAP) crash test data. Phase II: The Toyota HUman Model for Safety (THUMS) v4.01 was positioned in 120 precrash configurations per case within the SVM. Five occupant positioning variables were varied using a Latin hypercube design of experiments: seat track position, seat back angle, D-ring height, steering column angle, and steering column telescoping position. An additional baseline simulation was performed that aimed to match the precrash occupant position documented in CIREN for each case. Phase III: FE simulations were then performed using kinematic boundary conditions from each vehicle's event data recorder (EDR). HIC15, combined thoracic index (CTI), femur forces, and strain-based injury metrics in the lung and lumbar vertebrae were evaluated to predict injury.

Results: Tuning the SVM to specific vehicle models resulted in close matches between simulated and test injury metric data, allowing the tuned SVM to be used in each case reconstruction with EDR-derived boundary conditions. Simulations with the most rearward seats and reclined seat backs had the greatest HIC15, head injury risk, CTI, and chest injury risk. Calculated injury risks for the head, chest, and femur closely correlated to the CIREN occupant injury patterns. CTI in the Camry case yielded a 54% probability of Abbreviated Injury Scale (AIS) 2+ chest injury in the baseline case simulation and ranged from 34 to 88% (mean = 61%) risk in the least and most dangerous occupant positions. The greater than 50% probability was consistent with the case occupant's AIS 2 hemomediastinum. Stress-based metrics were used to predict injury to the lower leg of the Camry case occupant. The regional-level injury metrics evaluated for the Cobalt case occupant indicated a low risk of injury; however, strain-based injury metrics better predicted pulmonary contusion. Approximately 49% of the Cobalt occupant's left lung was contused, though the baseline simulation predicted 40.5% of the lung to be injured.

Conclusions: A method to compute injury metrics and risks as functions of precrash occupant position was developed and applied to 2 CIREN MVC FE reconstructions. The reconstruction process allows for quantification of the sensitivity and uncertainty of the injury risk predictions based on occupant position to further understand important factors that lead to more severe MVC injuries.     

Cervical spine loads and intervertebral motions during whiplash

OBJECTIVE: To quantify the dynamic loads and intervertebral motions throughout the cervical spine during simulated rear impacts. METHODS: Using a biofidelic whole cervical spine model with muscle force replication and surrogate head and bench-top mini-sled, impacts were simulated at 3.5, 5, 6.5, and 8 g horizontal accelerations of the T1 vertebra. Inverse dynamics was used to calculate the dynamic cervical spine loads at the centers of mass of the head and vertebrae (C1-T1). The average peak loads and intervertebral motions were statistically compared (P < 0.05) throughout the cervical spine. RESULTS: Load and motion peaks generally increased with increasing impact acceleration. The average extension moment peaks at the lower cervical spine, reaching 40.7 Nm at C7-T1, significantly exceeded the moment peaks at the upper and middle cervical spine. The highest average axial tension peak of 276.9 N was observed at the head, significantly greater than at C4 through T1. The average axial compression peaks, reaching 223.2 N at C5, were significantly greater at C4 through T1, as compared to head-C1. The highest average posterior shear force peak of 269.5 N was observed at T1. CONCLUSION: During whiplash, the cervical spine is subjected to not only bending moments, but also axial and shear forces. These combined loads caused both intervertebral rotations and translations.     

Survival Model for Foot and Leg High Rate Axial Impact Injury Data

Objectives: Understanding how lower extremity injuries from automotive intrusion and underbody blast (UBB) differ is of key importance when determining whether automotive injury criteria can be applied to blast rate scenarios. This article provides a review of existing injury risk analyses and outlines an approach to improve injury prediction for an expanded range of loading rates. This analysis will address issues with existing injury risk functions including inaccuracies due to inertial and potential viscous resistance at higher loading rates.

Methods: This survival analysis attempts to minimize these errors by considering injury location statistics and a predictor variable selection process dependent upon failure mechanisms of bone. Distribution of foot/ankle/leg injuries induced by axial impact loading at rates characteristic of UBB as well as automotive intrusion was studied and calcaneus injuries were found to be the most common injury; thus, footplate force was chosen as the main predictor variable because of its proximity to injury location to prevent inaccuracies associated with inertial differences due to loading rate. A survival analysis was then performed with age, sex, dorsiflexion angle, and mass as covariates. This statistical analysis uses data from previous axial postmortem human surrogate (PMHS) component leg tests to provide perspectives on how proximal boundary conditions and loading rate affect injury probability in the foot/ankle/leg (n = 82).

Results: Tibia force-at-fracture proved to be up to 20% inaccurate in previous analyses because of viscous resistance and inertial effects within the data set used, suggesting that previous injury criteria are accurate only for specific rates of loading and boundary conditions. The statistical model presented in this article predicts 50% probability of injury for a plantar force of 10.2 kN for a 50th percentile male with a neutral ankle position. Force rate was found to be an insignificant covariate because of the limited range of loading rate differences within the data set; however, compensation for inertial effects caused by measuring the force-at-fracture in a location closer to expected injury location improved the model's predictive capabilities for the entire data set.

Conclusions: This study provides better injury prediction capabilities for both automotive and blast rates because of reduced sensitivity to inertial effects and tibia–fibula load sharing. Further, a framework is provided for future injury criteria generation for high rate loading scenarios. This analysis also suggests key improvements to be made to existing anthropomorphic test device (ATD) lower extremities to provide accurate injury prediction for high rate applications such as UBB.     

Predicting multiplanar cervical spine injury due to head-turned rear impacts using IV-NIC

OBJECTIVE: Intervertebral Neck Injury Criterion (IV-NIC) hypothesizes that dynamic three-dimensional intervertebral motion beyond physiological limit may cause multiplanar soft-tissue injury. Present goals, using biofidelic whole human cervical spine model with muscle force replication and surrogate head in head-turned rear impacts, were to: (1) correlate IV-NIC with multiplanar injury, (2) determine IV-NIC injury threshold at each intervertebral level, and (3) determine time and mode of dynamic intervertebral motion that caused injury. METHODS: Impacts were simulated at 3.5, 5, 6.5, and 8 g horizontal accelerations of T1 vertebra (n = 6; average age: 80.2 years; four male, two female donors). IV-NIC was defined at each intervertebral level and in each motion plane as dynamic intervertebral rotation divided by physiological limit. Three-plane pre- and post-impact flexibility testing measured soft-tissue injury; that is significant increase in neutral zone (NZ) or range of motion (RoM) at any intervertebral level, above baseline. IV-NIC injury threshold was average IV-NIC peak at injury onset. RESULTS: IV-NIC extension peaks correlated best with multiplanar injuries (P < 0.001): extension RoM (R = 0.55) and NZ (R = 0.42), total axial rotation RoM (R = 0.42) and NZ (R = 0.41), and total lateral bending NZ (R = 0.39). IV-NIC injury thresholds ranged between 1.1 at C0-C1 and C3-C4 to 2.9 at C7-T1. IV-NIC injury threshold times were attained between 83.4 and 150.1 ms following impact. CONCLUSIONS: Correlation between IV-NIC and multiplanar injuries demonstrated that three-plane intervertebral instability was primarily caused by dynamic extension beyond the physiological limit during head-turned rear impacts.     

The safety implications of vehicle seat adjustments

INTRODUCTION: The goal of this study was to gather information on the preferred front seat position of vehicle occupants and to determine the impact of variation in seat position on safety during crashes. METHOD: The study evaluated the relationship between seat position and occupant size using the chi-square test and compared the risk of severe injury for small females and large males with regard to forward and rearward seat position using logistic regression. RESULTS: While smaller drivers sat closer to the steering wheel than larger drivers, front passengers of all sizes used similar seat positions. Additionally, the risk of injury was higher for small, unbelted females in rearward seat positions and large males (belted and unbelted) in forward seat positions. CONCLUSIONS: Occupants who adjust their seats to positions that are not consistent with required federal tests are at a greater risk for severe injury in a crash.     

基于有限元的含腐蚀缺陷P110油管失效分析与安全评价

含有腐蚀缺陷油管在复杂的工作荷载下容易发生失效。建立了在内压与轴向力共同作用的复杂工作载荷下,含椭球型蚀坑缺陷与轴向沟槽型缺陷两种腐蚀缺陷的油管有限元模型。基于该模型研究了不同载荷工况下缺陷宽度、深度与长度对油管安全性及失效模式的影响。研究结果表明:腐蚀位置深度较浅时,椭球型蚀坑缺陷更危险,油管主要发生由轴力引发的断裂失效;腐蚀位置深度较深时,轴向沟槽型缺陷更危险,主要发生由内压引发的破裂失效。研究成果可为含腐蚀缺陷油管的安全评估提供依据。     

Computational modeling and analysis of thoracolumbar spine fractures in frontal crash reconstruction

Abstract

Objective: This study aimed to reconstruct 11 motor vehicle crashes (6 with thoracolumbar fractures and 5 without thoracolumbar fractures) and analyze the fracture mechanism, fracture predictors, and associated parameters affecting thoracolumbar spine response.

Methods: Eleven frontal crashes were reconstructed with a finite element simplified vehicle model (SVM). The SVM was tuned to each case vehicle and the Total HUman Model for Safety (THUMS) Ver. 4.01 was scaled and positioned in a baseline configuration to mimic the documented precrash driver posture. The event data recorder crash pulse was applied as a boundary condition. For the 6 thoracolumbar fracture cases, 120 simulations to quantify uncertainty and response variation were performed using a Latin hypercube design of experiments (DOE) to vary seat track position, seatback angle, steering column angle, steering column position, and D-ring height. Vertebral loads and bending moments were analyzed, and lumbar spine indices (unadjusted and age-adjusted) were developed to quantify the combined loading effect. Maximum principal strain and stress data were collected in the vertebral cortical and trabecular bone. DOE data were fit to regression models to examine occupant positioning and thoracolumbar response correlations.

Results: Of the 11 cases, both the vertebral compression force and bending moment progressively increased from superior to inferior vertebrae. Two thoracic spine fracture cases had higher average compression force and bending moment across all thoracic vertebral levels, compared to 9 cases without thoracic spine fractures (force: 1,200.6 vs. 640.8 N; moment: 13.7 vs. 9.2?Nm). Though there was no apparent difference in bending moment at the L1–L2 vertebrae, lumbar fracture cases exhibited higher vertebral bending moments in L3–L4 (fracture/nonfracture: 45.7 vs. 33.8?Nm). The unadjusted lumbar spine index correctly predicted thoracolumbar fracture occurrence for 9 of the 11 cases (sensitivity?=?1.0; specificity?=?0.6). The age-adjusted lumbar spine index correctly predicted thoracolumbar fracture occurrence for 10 of the 11 cases (sensitivity?=?1.0; specificity?=?0.8). The age-adjusted principal stress in the trabecular bone was an excellent indicator of fracture occurrence (sensitivity?=?1.0; specificity?=?1.0). A rearward seat track position and reclined seatback increased the thoracic spine bending moment by 111–329%. A more reclined seatback increased the lumbar force and bending moment by 16–165% and 67–172%, respectively.

Conclusions: This study provided a computational framework for assessing thoracolumbar fractures and also quantified the effect of precrash driver posture on thoracolumbar response. Results aid in the evaluation of motor vehicle crash–induced vertebral fractures and the understanding of factors contributing to fracture risk.     

Thoracic and lumbar spine responses in high-speed rear sled tests

Objective: This study analyzed thoracic and lumbar spine responses with in-position and out-of-position (OOP) seated dummies in 40.2 km/h (25 mph) rear sled tests with conventional and all-belts-to-seat (ABTS) seats. Occupant kinematics and spinal responses were determined with modern (≥2000 MY), older (<2000 MY), and ABTS seats.

Methods: The seats were fixed in a sled buck subjected to a 40.2 km/h (25 mph) rear sled test. The pulse was a 15 g double-peak acceleration with 150 ms duration. The 50th percentile Hybrid III was lap–shoulder belted in the FMVSS 208 design position or OOP, including leaning forward and leaning inboard and forward. There were 26 in-position tests with 11 <2000 MY, 8 ≥2000 MY, and 7 ABTS and 14 OOP tests with 6 conventional and 8 ABTS seats. The dummy was fully instrumented. This study addressed the thoracic and lumbar spine responses. Injury assessment reference values are not approved for the thoracic and lumbar spine. Conservative thresholds exist. The peak responses were normalized by a threshold to compare responses. High-speed video documented occupant kinematics.

Results: The extension moments were higher in the thoracic than lumbar spine in the in-position tests. For <2000 MY seats, the thoracic extension moment was 76.8 ± 14.6% of threshold and the lumbar extension moment was 50.5 ± 17.9%. For the ≥2000 MY seats, the thoracic extension moment was 54.2 ± 26.6% of threshold and the lumbar extension moment was 49.8 ± 27.7%. ABTS seats provided similar thoracic and lumbar responses. Modern seat designs lowered thoracic and lumbar responses. For example, the 1996 Taurus had ?1,696 N anterior lumbar shear force and ?205.2 Nm extension moment. There was ?1,184 N lumbar compression force and 1,512 N tension. In contrast, the 2015 F-150 had ?500 N shear force and ?49.7 Nm extension moment. There was ?839 N lumbar compression force and 535 N tension. On average, the 2015 F-150 had 40% lower lumbar spine responses than the 1996 Taurus. The OOP tests had similar peak lumbar responses; however, they occurred later due to the forward lean of the dummy.

Conclusions: The design and performance of seats have significantly changed over the past 20 years. Modern seats use a perimeter frame allowing the occupant to pocket into the seatback. Higher and more forward head restraints allow a stronger frame because the head, neck, and torso are more uniformly supported with the seat more upright in severe rear impacts. The overall effect has been a reduction in thoracic and lumbar loads and risks for injury.     

Computational investigation of the effects of knee airbag design on the interaction with occupant lower extremity in frontal and oblique impacts

Objective: The lower extremity of the occupant represents the most frequently injured body region in motor vehicle crashes. Knee airbags (KABs) have been implemented as a potential countermeasure to reduce lower extremity injuries. Despite the increasing prevalence of KABs in vehicles, the biomechanical interaction of the human lower extremity with the KAB has not been well characterized. This study uses computational models of the human body and KABs to explore how KAB design may influence the impact response of the occupant's lower extremities.

Methods: The analysis was conducted using a 50th percentile male occupant human body model with deployed KABs in a simplified vehicle interior. The 2 common KAB design types, bottom-deploy KAB (BKAB) and rear-deploy KAB (RKAB), were both included. A state-of-the-art airbag modeling technique, the corpuscular particle method, was adopted to represent the deployment dynamics of the unfolding airbags. Validation of the environment model was performed based on previously reported test results. The kinematic responses of the occupant lower extremities were compared under both KAB designs, 2 seating configurations (in-position and out-of-position), and 3 loading conditions (static, frontal, and oblique impacts). A linear statistical model was used to assess factor significance considering the impact responses of the occupant lower extremities.

Results: The presence of a KAB had a significant influence on the lower extremity kinematics compared to no KAB (P <.05) by providing early restraint and distributing contact force on the legs during airbag deployment. For in-position occupants, the KAB generally tended to decrease tibia loadings. The RKAB led to greater lateral motion of the legs compared to the BKAB, resulting in higher lateral displacement at the knee joint and abduction angle change (51.2 ± 21.7 mm and 15° ± 6.0°) over the dynamic loading conditions. Change in the seating position led to a significant difference in occupant kinematic and kinetic parameters (P <.05). For the out-of-position (forward-seated) occupant, the earlier contact between the lower extremity and the deploying KAB resulted in 28.4° ± 5.8° greater abduction, regardless of crash scenarios. Both KAB types reduced the axial force in the femur relative to no KAB. Overall, the out-of-position occupant sustained a raised axial force and bending moment of the tibia by 0.8 ± 0.2 kN and 21.1 ± 8.7 Nm regardless of restraint use.

Conclusions: The current study provided a preliminary computational examination on KAB designs based on a limited set of configurations in an idealized vehicle interior. Results suggested that the BKAB tended to provide more coverage and less leg abduction compared to the RKAB in oblique impact and/or the selected out-of-position scenario. An out-of-position occupant was associated with larger abduction and lower extremity loads over all occupant configurations. Further investigations are recommended to obtain a full understanding of the KAB performance in a more realistic vehicle environment.     

Intervertebral neck injury criterion for prediction of multiplanar cervical spine injury due to side impacts

OBJECTIVE: Intervertebral Neck Injury Criterion (IV-NIC) is based on the hypothesis that dynamic three-dimensional intervertebral motion beyond physiological limits may cause multiplanar injury of cervical spine soft tissues. Goals of this study, using a biofidelic whole human cervical spine model with muscle force replication and surrogate head in simulated side impacts, were to correlate IV-NIC with multiplanar injury and determine IV-NIC injury threshold for each intervertebral level. METHODS: Using a bench-top apparatus, side impacts were simulated at 3.5, 5, 6.5, and 8 g horizontal accelerations of the T1 vertebra. Pre- and post-impact flexibility testing in three-motion planes measured the soft tissue injury, i.e., significant increase (p < 0.05) in neutral zone (NZ) or range of motion (RoM) at any intervertebral level, above corresponding physiological limit. RESULTS: IV-NIC in left lateral bending correlated well with total lateral bending RoM (R = 0.61, P < 0.001) and NZ (R = 0.55, P < 0.001). Additionally, the same IV-NIC correlated well with left axial rotation RoM (R = 0.50, P < 0.001). IV-NIC injury thresholds (95% confidence limits) varied among intervertebral levels and ranged between 1.5 (0.6-2.4) at C3-C4 and 4.0 (2.4-5.7) at C7-T1. IV-NIC injury threshold times were attained beginning at 84.5 ms following impact. CONCLUSIONS: Present results suggest that IV-NIC is an effective tool for determining multiplanar soft tissue neck injuries by identifying the intervertebral level, mode, time, and severity of injury.     

轴向单缝偏心药柱爆破效应模型试验研究

为了探究轴向单缝偏心药柱在掏槽爆破中爆炸应力波传播规律和裂纹扩展情况,采用水泥砂浆模型试块开展模型爆破试验,采用超动态应变测试系统对爆炸应力场进行测量。结果表明:在相同爆心距下,背对切缝侧A测点仅为正对切缝侧B测点峰值应力的73.82%;一定角度范围内,峰值应力随偏转角度的增大而减小,偏转角度为0°时峰值应力最大,偏转角度为60°处峰值应力是偏转角度为30°处的74.39%,峰值应力在0°到60°范围内最大衰减达到32.74%;正对切缝方向产生一条贯通炮孔的主裂纹,裂纹发育优于其他方向,且切缝方向没有明显的细小裂纹,这表明轴向单缝偏心药柱具有良好的定向断裂能力。     

基于近场动力学的煤体单轴压缩全过程损伤演化规律研究*

为了研究煤体受压变形破坏情况,采用近场动力学理论、室内单轴压缩实验及数值模拟相结合的方式,演绎推导PD损伤本构力函数,分别在宏、微观2个方面对煤体损伤规律进行研究。研究结果表明:以近场动力学所推导的本构力函数对于复杂裂隙演化过程的研究具有独特优势,煤体受到外荷载作用后内部微结构会产生不同程度的损伤,损伤过程可分为:压密阶段、微裂纹的萌生扩展阶段、断裂破坏阶段;压密阶段后均伴随键的断裂,至破坏阶段时,键几乎完全断裂,导致煤样宏观失稳破坏;模拟模型在受到外载荷作用下,内部能量开始聚集,随着压力的增大,内部能量散开,最终呈“X”型分布,这与实验加载后煤样的损伤效果基本一致,以此来反演煤体内部微结构变化从而得到煤体损伤规律切实可行。