鼠李糖脂洗脱土壤中多氯联苯影响因素的研究

研究了由铜绿假单胞菌发酵产生的代表性生物表面活性剂鼠李糖脂（RL）对土壤中PCBs解吸的影响。结果表明,RL的种类与浓度、土壤污染类型、解吸时间、洗脱次数、pH以及离子强度对土壤中PCBs的洗脱有一定的影响,而温度对PCBs的洗脱影响很小。当RL浓度低于CMC时,对PCBs的洗脱没有明显的促进作用;当RL浓度高于CMC后,对PCBs的洗脱有显著的促进作用。具有较低HLB的单鼠李糖脂R2对PCBs的洗脱效果要优于二鼠李糖脂R1。人工污染土壤中PCBs的洗脱效果要高于陈化土壤。污染土壤中TOC的含量越高,PCBs的洗脱率越低。延长解吸时间和增加洗脱次数可增加土壤中PCBs的洗脱率。碱性环境（pH＞7）或增加RL溶液中的离子强度均有利于土壤中PCBs的洗脱。     

生物表面活性剂在城市污泥静态强制通风好氧堆肥中的作用

采用静态强制通风好氧堆肥模式对城市剩余污泥进行堆肥降解,并研究了生物表面活性剂鼠李糖脂对堆肥过程的作用。结果表明,堆肥过程中,添加了质量分数为0.015%鼠李糖脂溶液堆制处理和空白对照堆制处理的堆温变化都明显呈现出中温期0～5 d、高温期6～12 d和降温期13～28 d 3个阶段。实验组比空白组的堆体升温快、高温期持续时间长、堆体的含水率高。鼠李糖脂的添加,使实验组的微生物数量高于空白组。添加鼠李糖脂的堆体和空白堆体的种子发芽指数(GI)在堆肥结束时分别为53.70%和50.80%,说明鼠李糖脂促进了堆肥的腐熟,但由于相对浓缩效应,堆肥产品的重金属含量略高于空白堆体。生物表面活性剂的介入促进了堆肥中木质纤维素的初步降解。研究表明,添加鼠李糖脂能够改善堆肥处理的微环境,促进有机质降解和堆肥的腐熟。     

产糖脂类生物表面活性剂菌株鉴定及发酵条件优化

从胜利油田污水中筛选出的产生物表面活性剂菌株Bbai-1,经过生理生化鉴定及16S rDNA系统发育学分析确定其属于类短短芽孢杆菌属(Brevibacillus parabrevis),由建立的该菌株的系统发育树可知菌株Bbai-1与其他类短短芽孢杆菌类同源性较低,是一个新的种.薄层色谱和红外光谱分析结果表明此菌株所产的生物表面活性剂为一种新型的糖脂类生物表面活性剂.通过产量和表面张力双重指标对菌株Bbai-1产生物表面活性剂的条件进行优化,确定了其最佳发酵温度为25℃、盐度为8 g/L、pH为7.5.在最佳发酵条件下,生物表面活性剂的产量可达0.9764 g/L.此糖脂类生物表面活性剂具有较高的降低表面张力能力,在浓度为其临界胶束浓度(120 mg/L)时,可将水溶液的表面张力从66.15 mN/m降低至27.62 mN/m.     

鼠李糖脂洗脱氯丹和灭蚁灵污染场地土壤的工艺参数

优化了鼠李糖脂洗脱氯丹、灭蚁灵污染土壤的工艺条件,为开展有机氯农药污染场地土壤洗脱修复工程实践提供科学依据和技术参数。实验结果表明,随着洗脱剂———鼠李糖脂浓度的增加,氯丹和灭蚁灵的洗脱量呈现先增加后降低的趋势;洗脱时间和液固比对洗脱效果的影响趋势与浓度相同;在0~120 r/min范围内,氯丹和灭蚁灵洗脱量随着搅拌速度的增加而增大,80、120和200 r/min的洗脱量间差异不显著;单次洗脱量随洗脱次数的增加而降低,累计洗脱量则逐渐增大。综上所述,氯丹、灭蚁灵污染场地土壤鼠李糖脂洗脱的适宜工艺参数为鼠李糖浓度10 mmol/L,搅拌速度80 r/min,固液比1∶10,洗脱时间20 min,洗脱3次。     

鼠李糖脂对剩余污泥中铜和镍的去除

采用批次淋洗的方法研究了鼠李糖脂浓度、pH、淋洗时间、提取次数以及重金属形态对剩余污泥中Cu和Ni去除效果的影响。结果表明,随着鼠李糖脂浓度的增加,2种重金属的去除率增加,且鼠李糖脂在碱性条件下对Cu和Ni的去除效果较好,最高去除率可分别高达80.77%和46.74%;随着振荡时间和提取次数的增加,Cu和Ni的去除率随之增加,并明显高于去离子水的提取;对污泥重金属形态进行分析发现,鼠李糖脂能有效去除酸提取态的Cu和Ni。研究结论可为剩余污泥的资源化而产生重金属安全隐患问题提供解决的参考方案和奠定理论基础。     

4种表面活性剂及其混合物对p,p'-DDT污染土壤洗脱效果

为了研究表面活性剂对p,p'-DDT污染土壤的淋洗效果,选取了4种阴、非离子表面活性剂,对人工p,p'-DDT污染土壤进行单一和复配洗脱实验。结果表明,对于人工p,p'-DDT污染土壤,阴离子表面活性剂洗脱效果优于非离子表面活性剂,其中阴离子表面活性剂十二烷基硫酸钠（SDS）和鼠李糖脂（RL）的洗脱效果较好,添加量为15 000 mg·L-1时洗脱率分别达到44.5%和36.5%,均优于非离子表面活性剂吐温80（TW80）（30.4%）和曲拉通100（TR100）（20.3%）;研究还表明非离子表面活性剂在添加量达到10 000 mg·L-1后,继续增加表面活性剂浓度,洗脱效果提升不明显。混合表面活性剂体系中,总添加量为10 000 mg·L-1时,SDS-TW80混合体系对p,p'-DDT的洗脱率为42%,高于SDS-TR100（34.9%）、RL-TW80（33.4%）和RL-TR100（37.4%）,表面活性剂混合体系对于p,p'-DDT的淋洗有明显的协同作用。     

表面活性剂冲洗修复多氯联苯污染土壤多相流研究

多氯联苯(PCBs)是一种具有持久性、抗生物降解性、脂肪溶性和明显的生物毒性等特性的持久性有机污染物,PCBs在土壤中难于准确定位、难被分解和强烈吸附,去除土壤中PCBs比较困难.表面活性剂冲洗法可以通过提高PCBs溶解度和降低水-PCBs界面张力来实现PCBs从土壤中去除;表面活性剂冲洗PCBs污染土壤涉及气相、水相、NAPLs相和固相等物质,是多相共存并相互发生作用的过程,发生相对渗透率、饱和度和毛细压力的变化;另外,为研究表面活性剂冲洗土壤中PCBs的去除机理,并降低PCBs对研究人员的危害,采用微观孔隙结构网络模型是一种较新颖的和效果显著的研究方法.开展表面活性剂冲洗PCBs污染土壤多相流研究,可以为PCBs污染场地修复提供理论基础和实验支持,并促进我国POPs履约工作的顺利进行.     

生物表面活性剂及其在环境修复中的研究进展

生物表面活性剂是由微生物分泌的天然产物，由于其物理性质和化学结构与许多人工合成的表面活性剂相似，并且对土壤、淡水、海洋等生态系统毒性较低，因而在环境污染治理方面，特别是在重金属和石油等有机溶剂污染的原位和异位生物修复方面具有极大的应用潜力。主要综述了近年国内外生物表面活性剂在廉价制备、作用机理、环境修复中的研究进展。     

基于生物表面活性剂的柴油微乳体系构建与性能研究

以生物表面活性剂鼠李糖脂（RL）为表面活性剂,中长碳链正构醇（正丁醇、正戊醇、正己醇、正庚醇及正辛醇）为助表面活性剂,采用滴定法制备RL／柴油／正构醇／水柴油微乳体系,并考察了表面活性剂用量（Km）、助表面活性剂醇的种类及用量（δas）及离子强度对柴油微乳体系最大增溶水量（Wo）的影响,并对不同条件下获得的柴油微乳体系的运动粘度（μ）和表面张力（γ）进行了表征。通过荧光法测得RL在柴油中的临界胶束浓度CMC为7g／L。当生物表面活性剂与柴油的质量比Km为0．02,助表面活性剂选用正庚醇且醇与表面活性剂的质量比δgs为0．1,NaOH溶液质量分数为0．06％时,柴油微乳体系的肛和T较低,形。最大,性能较佳。     

比较两种表面活性剂淋洗去除土壤中的重金属

以停车场和湿地2种土壤为研究对象,分别使用表面活性剂鼠李糖脂和月桂基醚硫酸钠对土壤样品进行淋洗,考察2种表面活性剂对这2种土壤中重金属的去除能力差异及形态分布的影响,并分析淋洗后残留在土壤中表面活性剂的生物毒性。结果表明,2种表面活性剂均可在一定程度上去除2种土壤中的Cu、Cd、Pb和Zn。与湿地土壤相比,2种表面活性剂对停车场土壤中重金属的去除率均较高,且月桂基醚硫酸钠的去除能力优于鼠李糖脂。2种表面活性剂对可交换态重金属的去除效果最好,对残渣态重金属去除率较低。淋洗后2种土样中残留的鼠李糖脂及停车场土样中残留的月桂基醚硫酸钠的生物毒性低,湿地土壤中残留的月桂基醚硫酸钠具有一定生物毒性。     

Accumulation of hydroxylated polychlorinated biphenyls (OH-PCBs) and implications for PCBs metabolic capacities in three porpoise species

The present study investigated polychlorinated biphenyls (PCBs) and hydroxylated metabolites of PCBs (OH-PCBs) in blood from three porpoise species: finless porpoises (Neophocaena phocaenoides), harbor porpoises (Phocoena phocoena), and Dall’s porpoises (Phocoenoides dalli). The porpoises were found stranded or were bycaught along the Japanese coast. Concentrations of OH-PCB were the highest in Dall’s porpoises (58 pg g⁻¹ wet wt), second highest in finless porpoises (20 pg g⁻¹ wet wt), and lowest in harbor porpoises (8.3 pg g⁻¹ wet wt). The concentrations in Dall’s porpoises were significantly higher than the concentrations in finless porpoises and harbor porpoises (p < 0.05 and p < 0.01, respectively). There was a positive correlation between PCB and OH-PCB concentrations (r = 0.67, p < 0.001), suggesting the possible concentration-dependent induction of CYP enzymes. The three porpoise species may have exceptionally low metabolic capacities compared with other marine and terrestrial mammals, because low OH-PCB/PCB concentration ratios were found, which were 0.0016 for Dall’s porpoises, 0.0013 for harbor porpoises, and 0.00058 for finless porpoises. Distinct differences in the OH-PCB congener patterns were observed for the three species, even though they are taxonomically closely related.     

多氯联苯污染沉积物质量评价研究进展

介绍了多氯联苯污染沉积物质量评价的研究进展 ,其中 ,简单介绍了多氯联苯的有关概况及环境行为、沉积物质量评价方法及基准研究进展 ;最后 ,重点介绍了包括多氯联苯在内的憎水性有机物污染沉积物质量评价的研究现状及存在问题。     

重金属-多氯联苯复合污染土壤同步洗脱

电子垃圾拆解区土壤具有重金属与有机物复合污染的特性,尤其以Cu、Pb、Cd和多氯联苯(PCBs)的复合污染较为突出。为了同步脱除土壤中重金属与PCBs,选用增溶物质:Tween 80、TX-100、SDBS、β-环糊精与螯合剂柠檬酸依次组合进行复合污染土壤淋洗实验,应用批量平衡震荡法研究它们对重金属(Cu、Pb、Cd)与PCBs(Aroclor 1254)的洗脱效果。通过比较洗脱效果、环境友好性等方面,得出非离子表面活性剂Tween 80与天然螯合剂柠檬酸2种淋洗剂复合最佳;进一步研究两者的淋洗先后顺序、浓度配比、洗脱时间及淋洗剂pH对污染土壤洗脱效果的影响,结果表明,在Tween 80和柠檬酸均为10 g/L、pH=6、淋洗时间12 h时淋洗效果达到最佳,对Cu、Pb、Cd及PCBs的洗脱率分别达到98.77%、55.92%、66.82%和58.01%。因此,利用Tween80和柠檬酸组合可同时有效去除土壤重金属和PCBs,是复合污染土壤淋洗修复的有效淋洗剂。     

A national survey of polybrominated diphenyl ethers (PBDEs) and indicator polychlorinated biphenyls (PCBs) in Chinese mothers' milk

Seven polybrominated diphenyl ethers (PBDEs) congeners (BDE-28, BDE-47, BDE-99, BDE-100, BDE-153, BDE-154 and BDE-183) and six indicator polychlorinated biphenyls (PCBs) congeners (CB-28, CB-52, CB-101, CB-138, CB-153 and CB-180) were measured in 24 pooled human milk samples comprised of 1237 individual samples from 12 provinces in China. The samples were taken to estimate the background body burden of general population and assess nursing infant exposure via human milk in China. The median concentrations of ∑₇PBDEs and ∑₆PCBs were 1.49 and 10.50 ng g⁻¹ lipid weight (lw), respectively. BDE-28, BDE-47 and BDE-153 were predominant PBDE congeners accounting for nearly 70% of ∑₇PBDEs. As for indicator PCBs, CB-153 was the most abundant congener, followed by CB-138. In our study, there was no significantly statistical relationship between concentrations of PBDEs in milk samples and maternal age as well as dietary habits. ∑₇PBDEs did not correlate to ∑₆PCBs in Chinese mothers’ milk. The human exposure to indicator PCBs in China was found to be significantly determined by maternal age, dietary habits and geographical factors. It is suggested that Chinese general population is probably exposed to PBDEs with multiple sources and pathways. The estimated daily intakes (EDI) of BDE-47, BDE-99 and BDE-153 for the Chinese nursing infant were much lower than corresponding threshold reference values suggested by USEPA.     

PCBs污染土壤的CaO诱导低温热处理脱氯研究

研究了低温热处理脱氯技术对废弃电容器封存点附近污染土壤中多氯联苯脱氯的效果,考察反应温度、反应时间及CaO添加比例对PCBs去除率、脱氯率的影响以及反应前后土壤中污染物的组分变化.实验土样中PCBs浓度为107.7 mg/g,属于罕见高浓度PCBs污染土壤.当反应温度为400℃、停留时间4h、CaO添加比例为10%,PCBs的去除率为87.7%,脱氯率为85.3%.土壤样品中五氯联苯和四氯联苯反应后含量降低或未检出,部分反应后样品检出一氯联苯和联苯,说明在CaO诱导PCBs低温热处理脱氯反应中存在逐步脱氯/加氢反应途径.     

Dry deposition and soil-air gas exchange of polychlorinated biphenyls (PCBs) in an industrial area

Ambient air and dry deposition, and soil samples were collected at the Aliaga industrial site in Izmir, Turkey. Atmospheric total (particle + gas) ∑₄₁-PCB concentrations were higher in summer (3370 ± 1617 pg m⁻³, average + SD) than in winter (1164 ± 618 pg m⁻³), probably due to increased volatilization with temperature. Average particulate ∑₄₁-PCBs dry deposition fluxes were 349 ± 183 and 469 ± 328 ng m⁻² day⁻¹ in summer and winter, respectively. Overall average particulate deposition velocity was 5.5 ± 3.5 cm s⁻¹. The spatial distribution of ∑₄₁-PCB soil concentrations (n = 48) showed that the iron-steel plants, ship dismantling facilities, refinery and petrochemicals complex are the major sources in the area. Calculated air-soil exchange fluxes indicated that the contaminated soil is a secondary source to the atmosphere for lighter PCBs and as a sink for heavier ones. Comparable magnitude of gas exchange and dry particle deposition fluxes indicated that both mechanisms are equally important for PCB movement between air and soil in Aliaga.     

Distribution, source and risk assessment of polychlorinated biphenyls (PCBs) in urban soils of Beijing, China

The concentration of PCBs in urban soils of Beijing across six land types including business districts (BD), cultural and educational areas (CE), classical gardens (CG), public green (PG), residential areas (RA), and roadsides (RD) was investigated. The total concentrations of PCBs ranged from below method detection limit (M.D.L.) to 37.11 × 10⁻³ mg kg⁻¹ dry weight (mean: 11.70 × 10⁻³ mg kg⁻¹; median: 13.28 × 10⁻³ mg kg⁻¹), which was at a medium level compared with other cities around the world. In general, the levels of PCBs decreased from the center of Beijing city to the suburb, suggesting the increasing PCBs concentrations with the age of the urban area. For different types of land use, the highest level of PCBs was observed in CG soils which have the oldest age, and the homologue profiles were similar, which were predominated by lowly chlorinated congeners including di-, tri- and tetra-CBs. Principal component analysis indicated that local sources such as Aroclor 1016, 1242, and 1248 were important sources in addition to long-range transport of PCBs all over the world. Although the toxic equivalency (TEQ) concentrations of dioxin-like PCBs in all soil samples of Beijing were higher than those in other urban areas of China, they met the Canadian soil quality standard.     

Polychlorinated biphenyls (PCBs) in marine fishes from China: Levels, distribution and risk assessment

Muscle tissues of large yellow croakers (Pseudosciaena crocea) and sliver pomfret (Pampus argenteus) from nine coastal cities of East China including Dalian, Tianjin, Qingdao, Shanghai, Zhoushan, Wenzhou, Fuzhou, Quanzhou and Xiamen were analyzed for polychlorinated biphenyl (PCB) concentrations. Thirty-six PCB congeners were quantified in the fishes, of which 11 congeners were dioxin-like PCBs. The total PCB concentrations of the present study were at the low end of the global range, which may be related to the smaller usage and shorter consumption history of PCBs in China. PCBs 18, 29, 52, 66, 101, 104, 138, 153, 180 and 194 were the major constituents found in the fish samples. Regression analysis showed a strong positive correlation (R² = 0.800; p < 0.001) between total dioxin-like PCBs and total PCB concentrations, and that total PCB concentrations explain 80% of the variability in total dioxin-like PCB concentrations. Among the species investigated, significantly higher concentrations of total PCBs were found in croakers than in pomfrets, which may be attributed to their different feeding and living habits. No significant difference in total PCB concentrations among the cities was observed; principal component analysis (PCA) of PCB profiles indicated that PCB pollution came from similar sources in the sampling areas and that there may be other PCB sources in Dalian and Wenzhou. The calculated carcinogenic risks (CRs) from the two species based on a low consumption group and high consumption group were all greater than 10⁻⁶, suggesting that daily exposure to dioxin-like PCBs via fish consumption results in a lifetime cancer risk of greater than one in one million. In contrast, the hazard quotients (HQs) of noncancer risks were all less than unity.     

Polybrominated diphenyl ethers (PBDEs) and indicator polychlorinated biphenyls (PCBs) in marine fish from four areas of China

The levels of polybrominated diphenyl ethers (PBDEs) and indicator polychlorinated biphenyls (PCBs) were determined in marine fish from four areas of China (South China Sea, Bohai Sea, East China Sea, and Yellow Sea) using GC/NCI-MS and GC/ITMS, respectively. Total concentrations of eight PBDEs (BDE-28, 47, 99, 100, 153, 154, 183 and 209) in all samples ranged from 0.3 ng g⁻¹ ww (wet weight) to 700 ng g⁻¹ ww, with median and mean values of 85 ng g⁻¹ ww and 200 ng g⁻¹ ww, respectively. BDE-209 and BDE-47 were the major congeners in all samples, contributing 54% and 19% to the total concentration, respectively. The sum of seven indicator PCB levels (CB-28, 52, 101, 118, 138, 153, and 180) ranged from 0.3 ng g⁻¹ ww to 3.1 μg g⁻¹ ww, with median and mean values of 6.4 ng g⁻¹ ww and 398 ng g⁻¹ ww, respectively. High contributions of CB-138 (32%) and CB-153 (25%) were found in all samples. In general, pollutants measured in this study were at high levels when compared with previous studies from other regions in the world. The relative abundance of BDE-209 may suggest that deca-BDE sources existed in studied area. And principal component analysis (PCA) showed that there were other PBDE sources in Yellow Sea. The pattern and PCA showed that PCB pollutions came from similar sources in the studied areas. In addition, concentrations of ∑₇PBDEs (u/209) were strongly correlated with those of ∑₇PCBs in all fish (r = 0.907, n = 44).     

Monofluorinated analogues of polychlorinated biphenyls (F-PCBs): synthesis using the Suzuki-coupling, characterization, specific properties and intended use

An improved method, a palladium-catalyzed cross-coupling reaction the so-called Suzuki-coupling, was used to synthesize 19 monofluorinated analogues (F-PCBs) of polychlorinated biphenyls (PCBs), including analogues of PCBs 28, 52 and 81. The coupling of chlorinated and/or fluorinated isomers of aryl boronic acids with bromo- and/or iodobenzenes gave the desired F-PCB congeners in good to excellent yields. The self-coupling product of the aryl boronic acids was the major impurity, but this limitation could be minimized. The influence of ortho-substitution by chlorine on the reaction time was studied in detail. The F-PCBs were characterized by means of ¹H and ¹⁹F NMR and mass spectrometry (MS). F-PCBs show remarkably similar characteristics in many aspects to those of the corresponding non-fluorinated parent PCBs. Since fluorine is generally resistant to degradation, once incorporated into a substrate it functions as an indelible label that can be used to monitor structures and dynamics. F-PCBs may prove their usefulness as markers and tracers in mechanistic and toxicological studies. The aim of further research will be to test the suitability of fluorine as a sensitive probe in a broad range of applications, including synthesis, analytical, mechanistic and toxicological studies.