液相络合脱硝中吸收脱除NO的反应机理

在鼓泡反应器中研究了乙二胺合钴溶液吸收NO的反应机理。实验结果表明:[Co(en)_2(NO)(OH~-)]~+不能被O2直接氧化;[Co_2(en)_4O2(OH~-)]~(3+)基本没有脱除NO的能力;[Co_2(en)_4O_2(OH~-)]~(3+)能够与[Co(en)_2(NO)(OH~-)]~+反应生成NO_3~-和NO_2~-;[Co_2(en)_4O_2(OH~-)]~(3+)与[Co(en)_2(NO)(OH~-)]~+的混合溶液具有脱除NO的能力。     

烟气成分对负载V_2O_5-WO_3/TiO_2聚苯硫醚纤维脱除烟气中Hg~0的影响

通过固定床实验系统模拟烟气脱除Hg0的实验,研究了O2、HCl、NO、SO2、H2O和NH3对滤袋常用的聚苯硫醚(PPS)纤维负载V2O5-WO3/TiO2新型催化剂后脱除烟气中Hg0的影响,并分析其影响机理。结果表明,在温度为200℃、高纯N2气氛下,Hg0的脱除率很低,加入4%O2后,脱除率有所增加;0.05‰HCl条件下Hg0的脱除率仅为5%,而0.01‰HCl与4%O2并存的条件下,脱除率明显提高;NO对Hg0的催化氧化促进作用不是很显著;SO2对Hg0氧化具有毒害作用;H2O和NH3可抑制Hg0的脱除,O2的存在可抵消NH3的部分抑制作用。     

H2O2溶液同时脱硫脱硝实验研究

二氧化硫和氮氧化物是电厂产生的主要大气污染物,研究焦点越来越集中在在一个反应器内实现同时脱硫脱硝。实验以H2O溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,实验结果表明：H2O浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱除率影响显著,pH、氧含量对脱硝率影响不大。在整个实验范围内脱硫效率总是保持在98．5％以上,脱硝效率最高达到67．4％。     

K2Cr2O7溶液同时脱硫脱硝实验研究

采用K2Cr2O7溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,考察多种因素对SO2脱除率(即脱硫率)和NO脱除率(即脱硝率)的影响。实验结果表明:K2Cr2O7浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱硫率、脱硝率影响显著;当烟气流量为0.4L/min,气相中O2体积分数为6%,SO2体积分数为0.09%,NO体积分数为0.100%,K2Cr2O7摩尔浓度为10mmol/L,反应温度为40℃时,脱硫率、脱硝率分别达到100%和64.3%。     

Fenton氧化法同时脱硫脱硝的实验研究

应用Fenton液相氧化吸收法进行同时脱硫脱硝实验。首先,利用单因素实验,分别考察了H2O2浓度、Fe2+投加量、初始pH值、UV照射和温度对脱硫脱硝的影响。结果表明,SO2和NO去除率随着H2O2浓度和Fe2+投加量的增大而提高;初始pH对SO2和NO的去除有较大影响;UV能促进SO2和NO的净化;温度对脱硫效率影响不大,但对NO的去除有显著作用,适当升温可以提高脱硝效率。随后,考察了SO2对NO去除率的影响。通过单独脱硝和同时脱硫脱硝的对比实验发现,SO2的加入对NO的去除有一定的促进作用,Fenton法可同时获得起始约80%的脱硝效率和98%以上的脱硫效率。     

钒硅催化脱硫脱硝的研究

考察了经10% H2-90% Ar(体积分数)还原的钒硅催化剂在固定床石英玻璃反应器中的脱硫脱硝活性,研究了反应温度、SO2/NO摩尔比及O2浓度对SO2和NO脱除率的影响.结果表明,还原后的钒硅催化剂的平均NO脱除率提高了15%左右;反应温度对脱硫脱硝影响较大,当温度为400℃以上时SO2和NO脱除率基本保持稳定;SO2/NO摩尔比为2和5时,钒硅催化剂的NO脱除率较高;模拟烟气中有O2条件下的脱硫脱硝活性明显高于无O2条件,O2体积分数为6.00%时SO2和NO脱除率达到最大.     

催化氧化吸收法去除燃煤电厂烟气中Hg~0的研究

针对燃煤电厂汞污染问题,利用现有污染物设备实现汞的同步脱除是具有经济效益、环境效益与工程实用前景的一种方法。在广泛使用的湿法烟气脱硫(WFGD)系统中,研究过渡金属离子(Mn2+、Co2+、Ni 2+、Cu2+)与H2O2构成的类芬顿体系(简称M2+/H2O2体系)对烟气中Hg0的氧化脱除效果,以及不同H2O2浓度、反应温度、初始pH、SO2浓度对M2+/H2O2体系Hg0脱除效果的影响。结果表明,类芬顿试剂能有效促进烟气中Hg0的脱除,脱汞率随着H2O2浓度和过渡金属阳离子浓度增加而提高,且各过渡金属离子的催化氧化作用为Co2+Mn2+Ni 2+Cu2+。初始pH能促进M2+/H2O2体系Hg0的脱除,SO2的存在会起到一定抑制作用,反应温度会影响该系统对Hg0的脱除效果,脱汞最佳反应温度为55℃,符合工程运行条件。可见,采用直接向脱硫浆液中加入添加剂的方法能有效控制燃煤电厂汞污染,且该方法操作简单,具有很好的工业应用前景。     

Ce-Sn-W-O_x催化剂的配伍优化及脱硝影响因素

采用共混热解法制备系列Ce-Sn-W-Ox复合氧化物,用于NH3选择性催化还原NO。通过正交实验优化CeSn-W-Ox配方,采用环境扫描电镜(ESEM)、X-射线衍射仪(XRD)等表征分析催化剂的微观形貌和固相结构,确立Ce-Sn-WOx最佳配比及结构形貌。结果表明,以粒度为5~8 mm的堇青石瓷片担载分散Ce-Sn-W-Ox,进行NH3-SCR脱除NO,当Ce/Sn/W元素摩尔比为1∶0.8∶0.6时,Ce Sn0.8W0.6Ox/堇青石NH3-SCR脱除NO效果最好。当空速为7 200 h-1,催化剂在252~426℃内脱除NO效率均大于94%。重点考察了反应空速(GHSV)、水蒸气(H2O)、SO2等对Ce Sn0.8W0.6Ox/堇青石NH3-SCR脱除NO活性的影响。研究表明,空速低于10 000 h-1时,催化剂脱硝活性受空速影响小;单独通入5%H2O对催化剂脱硝活性基本没有影响;单独通入429 mg/m3SO2导致催化剂活性略有降低;同时通入429 mg/m3SO2和5%H2O,催化剂脱硝活性下降至85.33%,除去SO2和H2O后,催化剂活性又能明显回升。     

助剂(C_2H_4、NH_3)添加对AC/DC流光放电等离子体脱硝效果的影响

等离子体法脱硝被认为是一种非常环保有效的脱硝技术,为了探究等离子体对NO_x的作用过程,选用AC/DC流光放电等离子体及模拟烟气,考察了烟气流量和NO初始浓度、添加剂的种类与含量以及SO_2对等离子体脱硝的影响。结果表明:NO的脱除过程由氧化过程和还原过程同时作用,在同一功率下,NO_x脱除率随流量的增加而降低,NO初始浓度对NO_x脱除率无直接影响。氨的添加可以促进NO_x的还原脱除,乙烯的添加可以促进NO氧化转化为NO_2。烟气中SO_2存在会导致NO_x脱除效率降低,此时氨助剂的加入可以显著提高NO_x脱除率。当NH3∶SO_2=2∶1时,在15 W下SO_2脱除率可达100%,NO_x脱除率60%。     

聚丙烯腈基活性碳纤维用于烟气脱硫脱硝

应用聚丙烯腈基活性碳纤维(PAN-ACF)对模拟的工业烟气中的SO2和NO在烟气露点温度以上进行吸附脱除实验。通过改变固定床ACF装载量、反应温度、水蒸气体积分数和O2体积分数,研究了ACF脱硫效率和脱硝效率的变化规律,还研究了同时脱硫脱硝时入口SO2或NO浓度对脱除效率的影响。结果表明:PAN-ACF具有良好的脱硫性能和一定的脱硝能力,其脱硫效率和脱硝效率随着ACF装载量和O2体积分数的增大而升高,随着温度的升高而降低,随着水蒸气体积分数的增大先升高后降低;在同时脱硫脱硝时,SO2对ACF的脱硝反应有明显的抑制作用,而NO对ACF的脱硫反应影响不大。     

采用杂多酸化合物溶液同时脱硫脱氮的实验研究

本文对液相催化氧化脱硫脱氮的新方法进行了研究 ,在鼓泡反应发生器内进行了液相催化氧化脱硫脱氮的实验。采用钼硅酸溶液及其还原产物脱除烟气中的SO2 和NOX,分别就吸收液的浓度、pH值、温度、停留时间等因素对SO2 和NOX 去除效率的影响及其变化规律进行了研究。实验结果表明 ,钼硅酸能十分有效地吸收SO2 ,将SO2 氧化成H2 SO4,并使杂多酸还原为杂多蓝。随后又被用于去除NOX,把NOX 还原成N2 ,蓝色溶液再次被氧化成为黄色溶液     

Simultaneous absorption of NO and SO2 into hexamminecobalt(II)/iodide solution

An innovative catalyst system has been developed to simultaneously remove NO and SO2 from combustion flue gas. Such catalyst system may be introduced to the scrubbing solution using ammonia solution to accomplish sequential absorption and catalytic oxidation of both NO and SO2 in the same reactor. When the catalyst system is utilized for removing NO and SO2 from the flue gas, Co(NH3)(6)2+ ions act as the catalyst and I- as the co-catalyst. Dissolved oxygen, in equilibrium with the residual oxygen in the flue gas, is the oxidant. The overall removal process is further enhanced by UV irradiation at 365 nm. More than 95% of NO is removed at a feed concentration of 250-900 ppm, and nearly 100% of SO2 is removed at a feed concentration of 800-2500 ppm. The sulfur dioxide co-existing in the flue gas is beneficial to NO absorption into hexamminecobalt(II)/iodide solution. NO and SO2 can be converted to ammonium sulfate and ammonium nitrate that can be used as fertilizer materials. The process described here demonstrates the feasibility of removing SO2 and NO simultaneously only by retrofitting the existing wet ammonia flue-gas-desulfurization (FGD) scrubbers.     

Electrochemical oxidation of bisphenol A. Application to the removal of bisphenol A using a carbon fiber electrode

Leachate samples with a high strength of ammonium-nitrogen (NH4+-N) were collected from a local landfill site in Hong Kong. Two experiments were carried out to study (1) the inhibition of microbial activity of activated sludge by NH4+-N and (2) the chemical precipitation of NH4+-N from leachate as a preliminary treatment prior to the activated sludge process. The experimental results demonstrated that the efficiency of COD removal decreased from 97.7% to 78.1%, and the dehydrogenase activity of activated sludge decreased from 9.29 to 4.93 microg TF/mg MLSS, respectively, when the NH4+-N concentration increased from 53 to 800 mg/l. The experiment also demonstrated that the NH4+-N in the leachate can be quickly precipitated as MgNH4PO4 x 6H2O after addition of MgCl2 x 6H2O + Na2HPO4 x 12H2O. The NH4+-N concentration was reduced from 5618 to 112 mg/l within 15 min when a molar ratio of Mg2+:NH+:PO4(3-) = 1:1:1 was used. The optimum pH to reach the minimum solubility of MgNH4PO4 x 6H2O was found to be in the range of 8.5-9.0. Attention should be given to the high salinity formed in the treated leachate by using MgCl2 x 6H2O + Na2HPO4 x 12H2O, which may affect microbial activity in the following biological treatment processes. Using two other combinations of chemicals [MgO + 85%H3PO4 and Ca(H2PO4)2 x H2O + MgSO4 x 7H2O] could minimise salinity generation after precipitation, while they were less efficient for NH4+-N removal.     

天然黄铁矿的除磷性能

除磷是控制水体富营养化的重要手段。为了考察黄铁矿的除磷特征,采用序批实验,分别研究了反应时间、初始磷浓度和干扰离子（NH4＋、NO3- 和SO24-）对黄铁矿除磷的影响。动力学表明,黄铁矿的除磷过程符合伪二级动力学模型。pH=6．5时,磷的平衡去除量为6．82mg／kg。Langmuir方程能较好描述黄铁矿除磷的吸附等温过程,其磷的饱和吸附量为11．01mg／kg。NH4＋、NO3-和SO24- 对黄铁矿除磷基本没有影响。磷的去除主要是通过铁磷沉淀和铁氧化物及氢氧化物的吸附,去除的磷主要以可被生物利用的Fe、Al-P形态存在。黄铁矿的这些除磷性能和机制对选取黄铁矿作为人工湿地填料实现同步脱氮除磷具有重要指导作用。     

Atmospheric deposition and ionic interactions within a beech canopy in the Karkonosze Mountains

A method, of artificial foliage placed above rain collectors, which enables to estimate total atmospheric inputs of elements, was employed to study processes related to ionic flow through a tree canopy. The investigations were conducted within a beech forest in the Karkonosze Mountains, in 1996-1997. An analysis of net canopy exchange (throughfall flux-atmospheric input) revealed that NH4+, NO3-, H+ had been retained in the canopy, Ca2+, Na+, Cl-, SO(2-)4, PO(3-)4 flowed passively, whereas K+ and Mg2- had been removed from the tree foliage. Ammonium absorption was more efficient than that of NO3- ions, because NH4+ was taken up from rain-waters and aerosol-gaseous fraction of the atmospheric input, whereas NO3- ions were captured primarily from the latter source. Retention of H+ was also related exclusively to the aerosol-gaseous input. Leaching losses of K+ and Mg2+ did not result from exchange reactions of these ions with retained H+, but from ionic exchange between NH4+ and K+ + Mg2+. At the same time, neutralisation of H+ in the canopy has been attributed to NO3- absorption, resulting most likely from HNO3 vapour penetration into the plants.     

Ti-Ce-Zr-Ox复合脱硝催化剂的制备及其性能研究

采用共混法制备了Ti-Ce-Zr-Ox复合脱硝催化剂TiCe0.1Zr0.1O2.4,运用X射线衍射、氮气物理吸附、扫描电镜等表征手段,分别对该催化剂的晶型、表面积、孔分布及结构形貌进行了分析,同时考察了反应温度、空速、水蒸气和SO2对该催化剂NH3选择性催化还原NO的影响.结果表明,TiCe0.1Zr0.1O2.4催...     

磷酸铵镁沉淀法预处理垃圾渗滤液

探讨了用磷酸铵镁沉淀法预处理垃圾渗滤液时,沉淀剂种类、pH值、物质摩尔配比和反应时间等因素对氨氮去除效果的影响。得出了处理氨氮浓度为2 677.34 mg/L的垃圾渗滤液时,在兼顾所用镁盐量尽量低和处理出水氨氮或磷酸盐的残留量都比较低的较佳实验条件为:沉淀剂种类为:MgSO4.7H2O和Na2HPO4.12H2O,反应时间为20 min,pH=9.5,n(Mg)∶n(P)∶n(N)=1.3∶1.15∶1.0。在较佳实验条件下,垃圾渗滤液的NH3-N去除率为97.05%,处理出水PO34--P含量为8.35 mg/L,NH3-N含量为75.86 mg/L。对所得沉淀物进行了成分分析和X-衍射光谱、扫描电镜表征,表明大部分沉淀物为磷酸铵镁物质。     

电化学法去除SO2/NOX的研究进展

本文对采用电化学方法去除SO2/NOx废气这一新的研究方法进行了综述.在用酞花青钴(CoPc)修饰的碳气体扩散电极上,SO2在空气中的体积百分数在20%以下时可以完全被氧化为硫酸,以连二硫酸盐(S2O2-4)作还原剂,Fe2+-EDTA作络合剂时,NO以90%以上的程度还原为NH+4与NH2(SO3H)等低价含氮化合物,产物中未见N2、N2O与NO2等气体,氧化产物SO2-3(或HSO-3)在Pb阴极上还原再生为S2O2-4.用Ce4+作氧化剂可将SO2/NO2氧化为相应的酸,还原产物Ce3+经电解氧化后循环使用.     

Simultaneous removal of nitrogen oxide/nitrogen dioxide/sulfur dioxide from gas streams by combined plasma scrubbing technology

Oxides of nitrogen (NOx) [nitrogen oxide (NO) + nitrogen dioxide (NO2)] and sulfur dioxide (SO2) are removed individually in traditional air pollution control technologies. This study proposes a combined plasma scrubbing (CPS) system for simultaneous removal of SO2 and NOx. CPS consists of a dielectric barrier discharge (DBD) and wet scrubbing in series. DBD is used to generate nonthermal plasmas for converting NO to NO2. The water-soluble NO2 then can be removed by wet scrubbing accompanied with SO2 removal. In this work, CPS was tested with simulated exhausts in the laboratory and with diesel-generator exhausts in the field. Experimental results indicate that DBD is very efficient in converting NO to NO2. More than 90% removal of NO, NOx, and SO2 can be simultaneously achieved with CPS. Both sodium sulfide (Na2S) and sodium sulfite (Na2SO3) scrubbing solutions are good for NO2 and SO2 absorption. Energy efficiencies for NOx and SO2 removal are 17 and 18 g/kWh, respectively. The technical feasibility of CPS for simultaneous removal of NO, NO2, and SO2 from gas streams is successfully demonstrated in this study. However, production of carbon monoxide as a side-product (approximately 100 ppm) is found and should be considered.     

The utilization of catalyst sorbent in scrubbing acid gases from incineration flue gas

Catalyst sorbents based on alumina-supported CuO, CeO2, and CuO-CeO2 were applied to a dry scrubber to clean up the SO2/HCl/NO simultaneously from pilot-scale fluidized-bed incineration flue gas. In the presence of organic compounds, CO and the submicron particles SO2 and HCI removed by the fresh catalyst sorbents and NO reduced to N2 by NH3 under the catalysis of fresh and spent desulfurization/dechloridization (DeSO2/DeHCl) catalyst sorbents (copper compounds, Cu, CuO, and CuSO4) were evaluated in this paper. The fresh and spent catalyst sorbents were characterized by the Brunner-Emmett-Teller method (BET), X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), inductively coupled plasma-mass spectrometry (ICP-MS), and the elemental analyzer (EA). The study showed that the performances of CuO, CeO2, and CuO-CeO2/gamma-Al2O3 were better than that of Ca(OH)2. The removal efficiency of SO2 and HCl was 80-95% in the dry scrubber system. Under NH3/NO = 1, NO could not be reduced to N2 because it was difficult to control the ratio of air/fuel in the flue gas. For estimating the feasibility of regenerating the spent catalyst sorbents, BET and EA analyses were used. They indicated that the pore structures were nearly maintained and a small amount of carbon accumulated on their surface.