Cloud point extraction of trace cyanide from environmental waters for indirect flame atomic absorption spectrometric determination

A method has been developed for indirect determination of cyanide in environmental waters based on cloud point extraction (CPE), preconcentration and determination by flame atomic absorption spectrometry (FAAS). The method was based on reduction of Cu(II) to Cu(I) in the presence of cyanide and complexation of the produced Cu(I)(CN)₂^? with gallocyanin (GC⁺) as an ion-pairing reagent at pH 4.0, followed by its extraction into polyethyleneglycol mono-p-nonylphenylether (Ponpe 7.5). Selectivity was improved with the use of suitable masking agents. Various factors influencing separation and preconcentration of cyanide have been investigated, and conditions were optimized, allowing determination of cyanide in the range of up to 1.2 mg L^?1 with a detection limit of 0.00045 mg L^?1. The method has been applied to the determination of cyanide in environmental waters, the results being in agreement with those obtained by a reference method.     

Determination of Au(III) and Pd(II) ions by flame atomic absorption spectrometry in some environmental samples after solid phase extraction

A simple and sensitive solid phase extraction method was developed for simultaneous separation and preconcentration of gold and palladium ions with N-(4-methylphenyl)-2-{[(4-phenyl-5-pyridine-4-yl-4H-1,2,4-triazol-3-yl)thio]acetyl}hydrazine carbo thioamide complex on Amberlite XAD-1180 resin before their determination by flame atomic absorption spectrometry. Some analytical parameters such as HNO₃ concentration of the sample solution, amount of complexing agent, sample volume, eluent type and volume, effects of foreign ions and adsorption capacity of the resin were investigated for quantitative recovery of gold and palladium ions. The effects of some anions and cations were also examined. Under optimum conditions, the detection limits for gold and palladium ions were found to be 0.29 and 0.19 μg L^?1, respectively. The preconcentration factor for gold and palladium was 250. After being validated by standard addition and analysis of standard reference material, the procedure was successfully applied to the analysis of sea and stream water, anodic slime, gold ore, soil and electronic waste.     

Cadmium and nickel determinations in some food and water samples by the combination of carrier element-free coprecipitation and flame atomic absorption spectrometry

A procedure for separation and enrichment of Cd(II) and Ni(II) ions based upon carrier element-free coprecipitation by using an organic coprecipitant, 2-{4-[2-(1H-Indol-3-yl)ethyl]-3-(4-methylbenzyl)-5-oxo-4,5-dihydro-1H-1,2,4-triazol-1-yl}-N′-(3-fluoro-phenylmethyliden) acetohydrazide, prior to their flame atomic absorption spectrometric detections has been developed. The effects of varied experimental conditions on the performance of the developed method such as pH, sample volume, amount of coprecipitating agent, etc. were evaluated in detail on the recovery of analyte ions, and the influences of some anions and cations were investigated. The limits of detection for Cd(II) and Ni(II) ions based on three times the standard deviation of the blanks (N: 10) were obtained as 0.70 μg L^?1 and 1.21 μg L^?1, respectively. The accuracy of the method was tested by analyzing a certified reference material and by spike tests. The method was applied to determine the levels of cadmium and nickel in stream and sea water, rice, red lentil, and wheat samples.     

Electrochemical hydride generation of tin(II) and its determination by electrothermal atomic absorption spectrometry with in situ trapping in the graphite tube atomizer

An electrolytic hydride generation system for the determination of tin(II) by means of batch electrochemical hydride generation-electrothermal atomic absorption spectrometry (EcHG-ETAAS) with in situ trapping in a graphite tube atomizer is described. The effects of four permanent chemical modifiers – palladium, tungsten, iridium, and platinum – for graphite tube treatment on analyte absorbance and the effects of four cathode materials, i.e., Pb, Sn, Pb–Sn alloy, and glassy carbon, are checked. Three electrolytes, i.e., nitric acid, sulfuric acid, and hydrochloric acid, are examined as catholyte solutions. The influence of several parameters on EcHG is investigated using multivariate and univariate methods. Interferences of some concomitant ions are evaluated. The calibration curve is linear from 1 to 200?µg?L^?1, with a detection limit of 0.8?µg?L^?1 and a relative standard deviation of 6.2% (n?=?3) for 100?µg?L^?1 Sn(II). The proposed method was successfully applied in the analysis of real environmental water samples and reference materials, and good spiked recoveries over the range of 93.1–115% were obtained. The proposed technique provides a means for developing hydride generation of other elements.     

干法灰化和微波消解-火焰原子吸收法测定铅锌冶炼厂废旧除尘布袋中重金属

采用干法灰化和微波消解两种样品分解方法处理广东省某铅锌冶炼厂布袋试样,用火焰原子吸收光谱法测定样品中Cu、Zn、Pb、Cr、Ni、Cd 6种重金属元素含量.同时用两种前处理方法对国家一级标准物质进行测定,与标准值比对,验证两种方法的准确度和精密度.结果表明,不同的样品分解方法对各重金属元素的测定结果会产生不同程度的影响.微波消解法相对于干法灰化法的准确度高,试剂利用率高,有利于元素的分析.干法灰化和微波消解两种前处理方法的精密度（RSD,n=11）均小于5%.     

Oxidized multiwalled carbon nanotubes modified with 2-(2-hydroxy-5-nitrophenyl)-4,5-diphenyl imidazole for solid phase extraction and preconcentration of some metal ions

In this work, a new procedure for the enrichment of the trace amount of Cu²⁺, Ni²⁺, Co²⁺, Pb²⁺, Fe²⁺, and Zn²⁺ ions based on the utilization of multiwalled carbon nanotubes (MWCNT) modified with 2-(2-hydroxy-5-nitrophenyl)-4,5-diphenyl imidazole as chelating agent prior to their determination by flame atomic absorption spectrometry has been described. The influence of effective parameters including pH, amount of ligand and MWCNT, composition of eluent, and coexisting ions on recoveries of understudy metal ions was examined. At the optimum pH of 5.0, all metal ions were quantitatively sorbed onto the proposed solid phase and completely desorbed with 8?mL of 5.0?mol?L^?1 HNO₃. The detection limit of Cu²⁺, Co²⁺, Ni²⁺, Pb²⁺, Fe²⁺, and Zn²⁺ ions was 1.7, 2.4, 2.3, 2.9, 2.8, and 1.4?µg?L^?1, while the preconcentration factor was 63 for Cu²⁺ and 94 for the other metal ions and relative standard deviations between 1.8 less than 3.0%. The proposed procedure was applied for the analysis of various samples.     

Solid phase extraction of Cu (II), Ni (II), Co (II), and Fe (III) ions in water samples using salicylaldehyde benzoylhydrazone on Amberlite XAD-4 and their determinations by flame atomic absorption spectrometry

A multi element preconcentration procedure for solid phase extraction on Amberlite XAD-4 as their salicylaldehyde benzoylhydrazone chelates and flame atomic absorption spectrometric determination of some trace metal ions in water samples are proposed in this work. The influences of some analytical parameters, including pH of aqueous solution, amounts of reagent, flow rates of sample and eluent solutions, and sample volume on the quantitative recoveries of copper, nickel, cobalt, and iron were investigated. The effects of concomitant ions on the retentions of the analytes were also examined. The developed method has been successfully applied to the determination of metal ions in some real samples, including, tap water, river water, spring water, and waste water.     

Preconcentration of some trace metal ions on coated alumina modified by 1-((6-(-(2-hydroxynaphthalen-1-yl)methyleneamino) hexylimino) methyl) naphthalen-2-ol

A sensitive and efficient method for preconcentration of trace amounts of some metal ions such as Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Pb²⁺, Cd²⁺, Cr³⁺, and Fe³⁺ ions based on modification of sodium-dodecyl-sulphate (SDS) coated alumina with 1-(6-(-(2-hydroxynaphthalen-1-yl) methyleneamino) hexylimino) methyl) naphthalen-2-ol (HNMAHN) is reported. The method is based on the uptake of these ions following their chelation with HNMAHN and their recovery using a suitable eluent. The influence of parameters such as pH, concentration of ligand and amount of coated alumina, SDS concentration, eluent (type and concentrations), and elution volume on metal ion recoveries are investigated. The preconcentration factor is 150 (10?mL elution volume) for a 1500?mL sample volume. The method has been successfully applied for extraction and determination of these ions content in some real samples. Extraction efficiency is generally >95% with low relative standard deviations between 1.8% and 2.4 %.