Precious Metals in Municipal Solid Waste Incineration Bottom Ash

Municipal solid waste incineration (MSWI) bottom ash contains economically significant levels of silver and gold. Bottom ashes from incinerators at Amsterdam and Ludwigshafen were sampled, processed, and analyzed to determine the composition, size, and mass distribution of the precious metals. In order to establish accurate statistics of the gold particles, a sample of heavy non-ferrous metals produced from 15 tons of wet processed Amsterdam ash was analyzed by a new technology called magnetic density separation (MDS). Amsterdam’s bottom ash contains approximately 10 ppm of silver and 0.4 ppm of gold, which was found in particulate form in all size fractions below 20 mm. The sample from Ludwigshafen was too small to give accurate values on the gold content, but the silver content was found to be identical to the value measured for the Amsterdam ash. Precious metal value in particles smaller than 2 mm seems to derive mainly from waste of electrical and electronic equipment (WEEE), whereas larger precious metal particles are from jewelry and constitute the major part of the economic value. Economical analysis shows that separation of precious metals from the ash may be viable with the presently high prices of non-ferrous metals. In order to recover the precious metals, bottom ash must first be classified into different size fractions. Then, the heavy non-ferrous (HNF) metals should be concentrated by physical separation (eddy current separation, density separation, etc.). Finally, MDS can separate gold from the other HNF metals (copper, zinc). Gold-enriched concentrates can be sold to the precious metal smelter and the copper-zinc fraction to a brass or copper smelter.     

Mechanical properties of Municipal Solid Waste by SDMT

In the paper the results of a geotechnical investigation carried on Municipal Solid Waste (MSW) materials retrieved from the “Cozzo Vuturo” landfill in the Enna area (Sicily, Italy) are reported and analyzed. Mechanical properties were determined both by in situ and laboratory large-scale one dimensional compression tests.While among in situ tests, Dilatomer Marchetti Tests (DMT) is used widely in measuring soil properties, the adoption of the DMT for the measurements of MSW properties has not often been documented in literature. To validate its applicability for the estimation of MSW properties, a comparison between the seismic dilatometer (SDMT) results and the waste properties evaluated by laboratory tests was carried out.Parameters for “fresh” and “degraded waste” have been evaluated. These preliminary results seems to be promising as concerns the assessment of the friction angle of waste and the evaluation of the S-wave in terms of shear wave velocity. Further studies are certainly required to obtain more representative values of the elastic parameters according to the SDMT measurements.     

A historical perspective of Global Warming Potential from Municipal Solid Waste Management

The Municipal Solid Waste Management (MSWM) sector has developed considerably during the past century, paving the way for maximum resource (materials and energy) recovery and minimising environmental impacts such as global warming associated with it. The current study is assessing the historical development of MSWM in the municipality of Aalborg, Denmark throughout the period of 1970 to 2010, and its implications regarding Global Warming Potential (GWP₁₀₀), using the Life Cycle Assessment (LCA) approach. Historical data regarding MSW composition, and different treatment technologies such as incineration, recycling and composting has been used in order to perform the analysis. The LCA results show a continuous improvement in environmental performance of MSWM from 1970 to 2010 mainly due to the changes in treatment options, improved efficiency of various treatment technologies and increasing focus on recycling, resulting in a shift from net emission of 618 kg CO₂-eq. tonne^?1 to net saving of 670 kg CO₂-eq. tonne^?1 of MSWM.     

Policy Barriers To 50% Diversion Of Municipal Solid Waste

A number of policy barriers must be addressed by the governments in Europe and North America which have adopted objectives of diverting from disposal something like 50% of the solid waste stream by means of reduction, re-use and recycling. These include: the need for clarification of responsibilities of all levels of government and of private sector product manufacturers and waste disposers; putting in place incentives for source separation; ensuring markets for recyclables; and allocating the increased cost of waste management. This paper reports on findings of a research project undertaken in 1991-92 on steps being taken by different jurisdictions to overcome such barriers.     

Composting Of <100 mm Fraction Of Municipal Solid Waste

A low cost solution for management of municipal solid waste in small municipalities was investigated; composting experiments were done using domestic waste. Particles >100 mm were removed, the screened substrate (<100 mm) was used for composting experiments on static piles. The results have shown that the size of waste does not affect composting. Though the inert material left greatly adds to the porosity, rainfall does not markedly affect the process; in fact excessive dryness gave the least stable end product, and total nitrogen, ammoniacal nitrogen and phosphorus content were the best pointers to the instability.     

The Origins Of Municipal Solid Waste: II. Policy Options For Plastics Waste Management

Plastic items in some portions of municipal solid waste (MSW), particularly from households and restaurants, have long been viewed as a disposal problem and a symbol of a "throwaway society". There is no question that the amount of plastics in solid waste is growing. However, this observation alone should not cause an hysteria of public policies for the separate management of the plastics or any other portion of the waste. The amount of plastics, and the contribution of the items discarded, must be viewed holistically in setting a solid waste management policy. This paper questions the basis for some U.S. plastics waste policy proposals by reviewing recent U.S. data on the effect of plastics on waste reduction, and the fate of discarded plastics products. Some alternative future policy directions are also discussed.     

Combined Municipal Solid Waste and biomass system optimization for district energy applications

Municipal Solid Waste (MSW) disposal has been a controversial issue in many countries over the past years, due to disagreement among the various stakeholders on the waste management policies and technologies to be adopted. One of the ways of treating/disposing MSW is energy recovery, as waste is considered to contain a considerable amount of bio-waste and therefore can lead to renewable energy production. The overall efficiency can be very high in the cases of co-generation or tri-generation. In this paper a model is presented, aiming to support decision makers in issues relating to Municipal Solid Waste energy recovery. The idea of using more fuel sources, including MSW and agricultural residue biomass that may exist in a rural area, is explored. The model aims at optimizing the system specifications, such as the capacity of the base-load Waste-to-Energy facility, the capacity of the peak-load biomass boiler and the location of the facility. Furthermore, it defines the quantity of each potential fuel source that should be used annually, in order to maximize the financial yield of the investment. The results of an energy tri-generation case study application at a rural area of Greece, using mixed MSW and biomass, indicate positive financial yield of investment. In addition, a sensitivity analysis is performed on the effect of the most important parameters of the model on the optimum solution, pinpointing the parameters of interest rate, investment cost and heating oil price, as those requiring the attention of the decision makers. Finally, the sensitivity analysis is enhanced by a stochastic analysis to determine the effect of the volatility of parameters on the robustness of the model and the solution obtained.     

The Origin And Fate Of Volatile Trace Components In Municipal Solid Waste Landfills

The content of readily volatile halogenated hydrocarbons (chlorinated and chlorinated, fluorinated hydrocarbons (VCCs/CFCs)) and the BTEX aromatic substances (benzene, toluene, ethylbenzene and xylene) in municipal solid waste (MSW) was determined by two different methods. Moreover, the emission potential of these substances via the gas and leachate phase was investigated during the different biological degradation phases in the landfill. Trichlorofluoromethane (R11), dichlorodifluoromethane (R12) and dichloromethane (R30) were the dominating halogenated trace substances detected in the MSW. In the acid phase, with some VCCs/CFCs the emittance may take place up to 30% via the water phase. Hexane, benzene, and toluene could be detected in all tests. Toluene often occurred in relatively high concentrations in MSW. It could be shown that R11 degraded into dichlorofluoromethane (R21).     

胶布热空气连续硫化废气的焚烧处理

比较了胶布热空气连续硫化废气的几种处理方法，认为焚烧法是最有效的处理方法，并对应用该法处理废气的工艺原理、主要设备、余热回收是焚烧过程中诮注意的事项作了较详尽的阐述。     

7-氨基-3-脱乙酰氧基头孢烷酸生产固体废物的处理

采用活性炭脱色—蒸馏—萃取—氯气置换的新工艺处理7-氨基-3-脱乙酰氧基头孢烷酸(7-ADCA)生产固体废物.实验结果表明:适宜的活性炭与7-ADCA生产固体废物的质量比为0.8％;以二氯甲烷作为溶剂萃取吡啶,萃取效率较高;在n(氯)∶n(溴)为1.2时,溴回收率为86.3％;在真空度为0.04 MPa、蒸馏温度为95℃的条件下,对釜底液进一步蒸馏浓缩,最终得到尿素和氯化铵混合固体肥料.与传统方法相比,该工艺不仅提高了经济效益,而且实现了7-ADCA生产固体废物的综合利用.     

Characterization of Compost from a Pilot Plant-scale Composter Utilizing Simulated Solid Waste

A pilot plant-scale composter using simulated solid waste was developed to test the fate of consumer products such as disposable diapers. The simulated waste consisted of a mixture of rabbit chow (which included alfalfa), shredded newspaper, sand, and composted cow manure. The compost mass self-heated from an ambient temperature of 27°C to about 55°C in the first 24 h. Dissolved ammonia levels, high in the early stages of the process, began to decrease after about 4 weeks as nitrate concentration began to increase. Both volatile solids and carbon:nitrogen ratios exhibited gradual decreases with time. Microbial biomass, esterase activity, cellulose mineralization, direct microscopic counts (AODC), and relative APIZYM enzyme activity increased significantly in the first several days, and maintained higher levels than initial measurements throughout the 22-week testing period. We concluded that the simulated solid waste underwent physical, chemical, and microbiological changes that would be expected to occur in municipal solid waste in a full-scale composting system. The pilot plant-scale composter should prove to be a valuable tool in assessing the fate of products and materials under simulated compost conditions.     

Environmental impacts of residual Municipal Solid Waste incineration: A comparison of 110 French incinerators using a life cycle approach

Incineration is the main option for residual Municipal Solid Waste treatment in France. This study compares the environmental performances of 110 French incinerators (i.e. 85% of the total number of plants currently in activity in France) in a Life Cycle Assessment perspective, considering 5 non-toxic impact categories: climate change, photochemical oxidant formation, particulate matter formation, terrestrial acidification and marine eutrophication. Mean, median and lower/upper impact potentials are determined considering the incineration of 1 tonne of French residual Municipal Solid Waste. The results highlight the relatively large variability of the impact potentials as a function of the plant technical performances. In particular, the climate change impact potential of the incineration of 1 tonne of waste ranges from a benefit of ?58 kg CO₂-eq to a relatively large burden of 408 kg CO₂-eq, with 294 kg CO₂-eq as the average impact. Two main plant-specific parameters drive the impact potentials regarding the 5 non-toxic impact categories under study: the energy recovery and delivery rate and the NO_x process-specific emissions. The variability of the impact potentials as a function of incinerator characteristics therefore calls for the use of site-specific data when required by the LCA goal and scope definition phase, in particular when the study focuses on a specific incinerator or on a local waste management plan, and when these data are available.     

利用废旧塑料和粉煤灰制建筑用瓦

探讨了利用废旧塑料和粉煤灰制建筑用瓦的工艺方法及条件,并与瓦的密度,吸水性、抗冻性、抗化性和抗折强度进行了检测。     

粉煤灰催化热裂解聚丙烯废塑料

在自制的废塑料催化热裂解装置和液体蒸馏装置上,研究了聚丙烯(PP)在粉煤灰催化作用下的热裂解特性。实验结果表明:随粉煤灰与PP的质量比增加,液体产物收率下降、气体产物收率增加,产物更加趋向于轻质化;残渣收率先降低后增加,但残渣收率总体偏低,不超过3%;液体产物中的汽油馏分收率先增加后下降,热裂解温度为460℃、粉煤灰与PP的质量比为0.2时汽油馏分收率为40.4%,热裂解温度为440℃、粉煤灰与PP的质量比为0.3时汽油馏分收率为37.9%;柴油馏分收率变化不明显;重油馏分收率下降,但当粉煤灰与PP的质量比超过0.3以后,重油馏分收率下降不再明显。     

A New and Sound Technology for Biogas from Solid Waste and Biomass

Organic waste, as a main constituent of municipal solid waste, has as well as solid biomass a high potential for biogas generation. Despite the importance of biogas generation from these materials, the availability of large-scale biogas processes lacks behind the demand. A newly developed double-stage solid–liquid biogas process, consisting of an open hydrolysis stage and a fixed-bed methane reactor, allows the biogas production from almost all biodegradable solid waste and renewable resources like maize, grass, sugar cane, etc. Furthermore, residues from industrial processes, like the glycerine waste water from biodiesel production, can also be converted into biogas successfully. Due to the strong separation of hydrolysis and methanation, the process is extremely stable. No malfunction has been detected so far. The open hydrolysis releases CO₂ and allows oxidation of sulfur. Consequently, the biogas has a high methane (>72%) and low H₂S concentration (<100 ppm). Stirrers or other agitation equipment are not necessary; only liquids are pumped. The biogas generation becomes controllable for the first time; thus, the actual generation can be easily adapted to the consumption.     

纯碱生产废水的综合治理

介绍了纯碱生产过程中产生的蒸氨废清液和生产下水的综合治理情况。将废清液晒盐回收ＮａＣｌ,然后从母液中回收ＣａＣｌ２。在雨季等情况下对废清液的治理措施是,将其两次兑海水,使其各项指标达到国家排放标准。     

Solid waste characterization and recycling potential for a university campus

Integrated waste management systems are one of the greatest challenges for sustainable development. For these systems to be successful, the first step is to carry out waste characterization studies. In this paper are reported the results of a waste characterization study performed in the Campus Mexicali I of the Autonomous University of Baja California (UABC). The aim of this study was to set the basis for implementation of a recovery, reduction and recycling waste management program at the campus. It was found that the campus Mexicali I produces 1ton of solid wastes per day; more than 65% of these wastes are recyclable or potentially recyclable. These results showed that a program for segregation and recycling is feasible on a University Campus. The study also showed that the local market for recyclable waste, under present conditions - number of recycling companies and amounts of recyclables accepted - can absorb all of these wastes. Some alternatives for the potentially recyclables wastes are discussed. Finally some strategies that could be used to reduce waste at the source are discussed as well.     

An Overview of Solid Waste Management and Plastic Recycling in Qatar

Municipal solid waste management (MSWM) constitutes one of the most crucial health and environmental problems facing authorities in the Arabian Gulf. Recent literature on current solid waste management (SWM) in Qatar has been reviewed in this paper, and a focused study has been carried out to provide a review on the total amount of municipal solid waste generated, stored, collected, disposed as well as the constituents of the waste. The analysis showed that Qatar produced around 2,000,000 tons of solid municipal waste annually, corresponding to a daily generation rate per capita of about 2.5 kg. About 60% of MSW is organic material and about 300 kg is composed daily. Landfill and composting is considered the most appropriate waste disposal techniques in Qatar. Um-Al-Afai landfill has nearly 80% of MSW. Because of the increased migration in Qatar, there is a sharp rise in the volume and also in the variety of solid waste. It is important to alleviate societal concerns over the increased rate of resource consumption and waste production; thus, policy makers have encouraged recycling and reuse strategies to reduce the demand for raw materials and to decrease the quantity of waste going to landfill. An example of the benefit of mechanical recycling of plastics compared to land filling and composting was conducted by GaBi 4 life cycle analysis tool which showed the benefits to the global warming and human toxicity. Recycling is the favored solution for plastic waste management, because it has a lower environmental impact on the defined impact categories, from Global Warming Potential (GWP) and Human Toxicity Potentials (HTP) indicators.