Measurements of ultrafine particles and other vehicular pollutants inside a mobile exposure system on Los Angeles freeways

A mobile exposure and air pollution measurement system was developed and used for on-freeway ultrafine particle health effects studies. A nine-passenger van was modified with a high-efficiency particulate air (HEPA) filtration system that can deliver filtered or unfiltered air to an exposure chamber inside the van. State-of-the-art instruments were used to measure concentration and size distribution of fine and ultrafine particles and the concentration of carbon monoxide (CO), black carbon (BC), particle-bound polycyclic aromatic hydrocarbons (PAHs), fine particulate matter (PM2.5) mass, and oxides of nitrogen (NOx) inside the exposure chamber. This paper presents the construction and technical details of the van and air pollutant concentrations collected in 32 2-hr runs on two major Los Angeles freeways, Interstate 405 (1-405; mostly gasoline traffic) and Interstate 710 (1-710; large proportion of heavy-duty diesel traffic). More than 97% of particles were removed when the flow through the filter box was switched from bypass mode to filter mode while the vehicle was driving on both freeways. The filtration system thus provides a great particulate matter exposure contrast while keeping gas-phase pollutant concentrations the same. Under bypass mode, average total particle number concentration observed inside the exposure chamber was around 8.4 x 10(4) and 1.3 x 10(5) particles cm(-3) on the I-405 and the I-710 freeways, respectively. Bimodal size distributions were consistent and similar for both freeways with the first mode around 16-20 nm and the second mode around 50-55 nm. BC and particle-bound PAH concentrations were more than two times greater on the I-710 than on the I-405 freeway. Very weak correlations were observed between total particle number concentrations and other vehicular pollutants on the freeways.     

Monitoring cellular responses of engine-emitted particles by using a direct air-cell interface deposition technique

The impacts of ultrafine airborne particles generated by diesel or gasoline engines on human lung cells have been investigated using a new in vitro cellular exposure technique. This technique enables direct deposition of the gasoline engine exhaust particles (GEP) and diesel engine exhaust particles (DEP) on human lung cells located at the air-cell interface on a transwell membrane in an exposure apparatus. The cellular responses to particle exposure were measured by the levels of IL-8 chemokines produced as a function of exposure time. The findings suggest that GEP and high-sulfur DEP induced the production of similar levels of IL-8 by unprimed A549 cells. The level of IL-8 produced by unprimed A549 cells in response to low-sulfur DEP was found lower than that produced in response to high-sulfur DEP and GEP. When cells were primed, simulating predisposed conditions, significant levels of IL-8 were produced. GEP triggered a much higher level of IL-8 production than DEP did. Furthermore, the time profile of IL-8 production induced by GEP was markedly different from that induced by DEP. The findings indicate that GEP could induce the production of higher levels of chemokines (i.e., IL-8) than DEP did, implying that exposure to GEP could be a greater health risk than exposure to DEP.     

Design and assessment of a chamber to expose plants to simulated aerosol and rain

Increased reports of contaminants in atmospheric aerosols necessitate the development of exposure systems that can accurately simulate aerosols for research purposes. This study outlines the design, construction, cost, and performance of a simple plexiglass chamber equipped with nozzles for rain and aerosol generation. The chamber occupies approximately 152 cm x 125 cm (height x width) space and can be used to expose six large (625 cm2) plants or twelve smaller (144 cm2) ones. The total cost of the materials used in construction, including nozzles, was less than 700 dollars. Repeated analysis of the quantity and particle size distribution of the simulated aerosol and rain showed them to be highly predictable. By adjusting the volume and/or concentration of the spray, and the position of plants within the chamber, particle sizes typical of environmental aerosols (< or = 20 microm) and rains (0.7 to 1.2 mm) could be applied to experimental plants. This sample, economical system will allow for precise simulations of important aerosols and rain events in the study of their impingement on plants.     

Overall dry deposition velocities of trace elements measured at harbor and traffic site in central Taiwan

For reasonable and convenient assessments of the characteristics of the dry deposition velocities between Taichung harbor site and Wuchi town site in central Taiwan, the overall dry deposition velocities of several metallic elements were calculated as the particulate diameter (D(p)) distributions of large particles (D(p) > 10 microm), coarse particles (10 microm < D(p) < 2.5 microm), and fine particles (D(p) < 2.5 microm) based on the ambient measurements during March-December of 2004. In this work, the dry deposition fluxes showed the higher correlation with coarse particle concentrations than large particle concentrations; however, the least well correlation was observed between the dry deposition fluxes and the fine particle concentrations. The calculated best-fit overall dry deposition velocities obtained using coarse particle concentrations varied from approximately 0.2 cm s(-1) for Cr to 1.5 cm s(-1) for Pb and 0.2 cm s(-1) for Fe to 2.6 cm s(-1) for Pb at Taichung harbor and Wuchi town site, respectively. In general, the crustal elements had higher deposition velocities than anthropogenic elements. In addition, overall dry deposition velocities for crustal elements were higher in Wuchi town site than in Taichung harbor site. The results identified the dry deposition flux was mainly contributed from large and coarse particles due to their high deposition velocities. The results also indicated that the best approach to estimate overall dry deposition was by depending on the characteristics of particles with diameters larger than 2.5 microm.     

Ultrafine particle emission from incinerators: the role of the fabric filter

Incinerators are claimed to be responsible of particle and gaseous emissions: to this purpose Best Available Techniques (BAT) are used in the flue-gas treatment sections leading to pollutant emission lower than established threshold limit values. As regard particle emission, only a mass-based threshold limit is required by the regulatory authorities. However; in the last years the attention of medical experts moved from coarse and fine particles towards ultrafine particles (UFPs; diameter less than 0.1 microm), mainly emitted by combustion processes. According to toxicological and epidemiological studies, ultrafine particles could represent a risk for health and environment. Therefore, it is necessary to quantify particle emissions from incinerators also to perform an exposure assessment for the human populations living in their surrounding areas. A further topic to be stressed in the UFP emission from incinerators is the particle filtration efficiency as function of different flue-gas treatment sections. In fact, it could be somehow important to know which particle filtration method is able to assure high abatement efficiency also in terms of UFPs. To this purpose, in the present work experimental results in terms of ultrafine particle emissions from several incineration plants are reported. Experimental campaigns were carried out in the period 2007-2010 by measuring UFP number distributions and total concentrations at the stack of five plants through condensation particle counters and mobility particle sizer spectrometers. Average total particle number concentrations ranging from 0.4 x 10(3) to 6.0 x 10(3) particles cm(-3) were measured at the stack of the analyzed plants. Further experimental campaigns were performed to characterize particle levels before the fabric filters in two of the analyzed plants in order to deepen their particle reduction effect; particle concentrations higher than 1 x 10(7) particles cm(-3) were measured, leading to filtration efficiency greater than 99.99%.     

Typical household vacuum cleaners: the collection efficiency and emissions characteristics for fine particles

The issue of fine particle (PM2.5) exposures and their potential health effects is a focus of scientific research because of the recently promulgated National Ambient Air Quality Standard for PM2.5. Before final implementation, the health and exposure basis for the standard will be reviewed by the U.S. Environmental Protection Agency within the next five years. As part of this process, it is necessary to understand total particle exposure issues and to determine the relative importance of the origin of PM2.5 exposure in various micro-environments. The results presented in this study examine emissions of fine particles from a previously uncharacterized indoor source: the residential vacuum cleaner. Eleven standard vacuum cleaners were tested for the emission rate of fine particles by their individual motors and for their efficiency in collecting laboratory-generated fine particles. An aerosol generator was used to introduce fine potassium chloride (KCl) particles into the vacuum cleaner inlet for the collection efficiency tests. Measurements of the motor emissions, which include carbon, and the KCl aerosol were made using a continuous HIAC/Royco 5130 A light-scattering particle detector. All tests were conducted in a metal chamber specifically designed to completely contain the vacuum cleaner and operate it in a stationary position. For the tested vacuum cleaners, fine particle motor emissions ranged from 9.6 x 10(4) to 3.34 x 10(8) particles/min, which were estimated to be 0.028 to 176 micrograms/min for mass emissions, respectively. The vast majority of particles released were in the range of 0.3-0.5 micron in diameter. The lowest particle emission rate was obtained for a vacuum cleaner that had a high efficiency (HEPA) filter placed after the vacuum cleaner bag and the motor within a sealed exhaust system. This vacuum cleaner removed the KCl particles that escaped the vacuum cleaner bag and the particles emitted by the motor. Results obtained for the KCl collection efficiency tests show > 99% of the fine particles were captured by the two vacuum cleaners that used a HEPA filter. A series of tests conducted on two vacuum cleaners found that the motors also emitted ultra-fine particles above 0.01 micron in diameter at rates of greater than 10(8) ultra-fine particles/CF of air. The model that had the best collection efficiency for fine particles also reduced the ultra-fine particle emissions by a factor of 1 x 10(3).     

An Analysis of Visual Range in the Eastern United States Under Different Meteorological Regimes

ABSTRACT

The issue of fine particle (PM₂₅) exposures and their potential health effects is a focus of scientific research because of the recently promulgated National Ambient Air Quality Standard for PM_{2 5}. Before final implementation, the health and exposure basis for the standard will be reviewed by the U.S. Environmental Protection Agency within the next five years. As part of this process, it is necessary to understand total particle exposure issues and to determine the relative importance of the origin of PM_{2 5} exposure in various micro-environments. The results presented in this study examine emissions of fine particles from a previously uncharacterized indoor source: the residential vacuum cleaner. Eleven standard vacuum cleaners were tested for the emission rate of fine particles by their individual motors and for their efficiency in collecting laboratory-generated fine particles. An aerosol generator was used to introduce fine potassium chloride (KC1) particles into the vacuum cleaner inlet for the collection efficiency tests. Measurements of the motor emissions, which include carbon, and the KCl aerosol were made using a continuous HIAC/Royco 5130A light-scattering particle detector. All tests were conducted in a metal chamber specifically designed to completely contain the vacuum cleaner and operate it in a stationary position. For the tested vacuum cleaners, fine particle motor emissions ranged from 9.6 x 10⁴ to 3.34 x 10⁸ particles/min, which were estimated to be 0.028 to 176 mg/min for mass emissions, respectively. The vast majority of particles released were in the range of 0.3-0.5 mm in diameter. The lowest particle emission rate was obtained for a vacuum cleaner that had a high efficiency (HEPA) filter placed after the vacuum cleaner bag and the motor within a sealed exhaust system. This vacuum cleaner removed the KC1particles that escaped the vacuum cleaner bag and the particles emitted by the motor. Results obtained for the KC1 collection efficiency tests show >99% of the fine particles were captured by the two vacuum cleaners that used a HEPA filter. A series of tests conducted on two vacuum cleaners found that the motors also emitted ultra-fine particles above 0.01 mm in diameter at rates of greater than 10⁸ ultra-fine particles/CF of air. The model that had the best collection efficiency for fine particles also reduced the ultra-fine particle emissions by a factor of 1 x 10³.     

Proinflammatory effect of fine and ultrafine particulate matter using size-resolved urban aerosols from Paris

Epidemiological and experimental studies have underlined that exposure to particulate matter (PM) leads mainly to airway inflammation, but the roles of particle size and chemical composition associated to such adverse health outcomes need to be better investigated. This study was performed to validate novel strategies of particle sampling, recovery and cell exposure in order to evaluate the pro-inflammatory potential of fine and ultrafine particles from a fractionated aerosol. Samplings of Paris background aerosols using 13-stage low pressure impactors (0.03-10 microm) gave bimodal mass distributions with an accumulation mode centered on a median diameter of 0.42 microm and a coarse one on 3.25 microm. PM 1 accounted for 70% and PM 0.1 for 12% of PM 10. The latter mainly comprised carbon-chained aggregates. The development of an efficient and reproducible method to recover fine (PM 1-0.1) and ultrafine (PM 0.1-0.03) particulate matter has permitted experimental comparison of the impact of such particles on human bronchial epithelial cells (HBECs). In this study we have compared the relative effects of fine and ultrafine particles at non-cytotoxic concentrations over 24h on the production of the pro-inflammatory cytokine GM-CSF by HBECs. Combining two cell exposure strategies to the size-fraction particles according to either their proportion (isovolume exposure) or their quantity in the aerosol (isomass exposure), we showed that both ultrafine and fine particles induced a concentration-dependent GM-CSF release by HBECs which is significant from 1 microg cm(-2). In conclusion, short duration samplings using 13-stage impactors enable to obtain size-resolved PM in sufficient quantities to carry out toxicological investigations. These findings are promising in view to conduct a more intensive study joining chemical and toxicological assays.     

Influence of atmospheric dispersion and new particle formation events on ambient particle number concentration in Rochester, United States, and Toronto, Canada

Continuous measurements of particle number concentrations were performed in Rochester, NY, and Toronto, Ontario, Canada during the 2003 calendar year. Strong seasonal dependency in particle number concentration was observed at two sites. The average number concentration of ambient particles was 9670 +/- 6960 cm(-3) in Rochester, whereas in Toronto the average number of particles was 28,010 +/- 13,350 cm(-3). The particle number concentrations were higher in winter months than in summer months by a factor of 1.5 in Rochester and 1.6 in Toronto. In general, there were also distinct diurnal variations of aerosol number concentration. The highest weekdays/weekends ratio of number concentration was typically observed during the rush-hour period in winter months with a ratio of 2.1 in Rochester and 2.0 in Toronto. The correlation in the total particle number concentrations between the two urban sites was stronger in winter because of the common urban traffic patterns, but weaker in summer because of local sulfur dioxide (SO2)-related particle formation events in Rochester in the summer. Strong morning particle formation events were frequently observed during colder winter months. Good correlations between particle number and carbon monoxide (CO) as well as temperature suggested that motorvehicle emissions lead to the formation of new particles as the exhaust mixes with the cold air. Regional nucleation and growth events frequently occurred in April. Local SO2-related particle formation events most frequently occurred in August. SO2 and UV-B were highly correlated with particle concentration, suggesting a high association of photochemical processes with these local events. A high directionality in a northerly direction was observed for particle number and SO2, indicating the influence of point sources located north of Rochester.     

Concentration and size distribution of ultrafine particles near a major highway

Motor vehicle emissions usually constitute the most significant source of ultrafine particles (diameter <0.1 microm) in an urban environment, yet little is known about the concentration and size distribution of ultrafine particles in the vicinity of major highways. In the present study, particle number concentration and size distribution in the size range from 6 to 220 nm were measured by a condensation particle counter (CPC) and a scanning mobility particle sizer (SMPS), respectively. Measurements were taken 30, 60, 90, 150, and 300 m downwind, and 300 m upwind, from Interstate 405 at the Los Angeles National Cemetery. At each sampling location, concentrations of CO, black carbon (BC), and particle mass were also measured by a Dasibi CO monitor, an aethalometer, and a DataRam, respectively. The range of average concentration of CO, BC, total particle number, and mass concentration at 30 m was 1.7-2.2 ppm, 3.4-10.0 microg/m3, 1.3-2.0 x 10(5)/cm3, and 30.2-64.6 microg/m3, respectively. For the conditions of these measurements, relative concentrations of CO, BC, and particle number tracked each other well as distance from the freeway increased. Particle number concentration (6-220 nm) decreased exponentially with downwind distance from the freeway. Data showed that both atmospheric dispersion and coagulation contributed to the rapid decrease in particle number concentration and change in particle size distribution with increasing distance from the freeway. Average traffic flow during the sampling periods was 13,900 vehicles/hr. Ninety-three percent of vehicles were gasoline-powered cars or light trucks. The measured number concentration tracked traffic flow well. Thirty meters downwind from the freeway, three distinct ultrafine modes were observed with geometric mean diameters of 13, 27, and 65 nm. The smallest mode, with a peak concentration of 1.6 x 10(5)/cm3, disappeared at distances greater than 90 m from the freeway. Ultrafine particle number concentration measured 300 m downwind from the freeway was indistinguishable from upwind background concentration. These data may be used to estimate exposure to ultrafine particles in the vicinity of major highways.     

Estimating the resuspension rate and residence time of indoor particles

Resuspension experiments were performed in a single-family residence. Resuspension by human activity was found to elevate the mass concentration of indoor particulate matter with an aerodynamic diameter less than 10 microm (PM10) an average of 2.5 times as high as the background level. As summarized from 14 experiments, the average estimated PM10 resuspension rate by a person walking on a carpeted floor was (1.4 +/- 0.6) x 10(-4) hr(-1). The estimated residence time for PM in the indoor air following resuspension was less than 2 hr for PM10 and less than 3 hr for 2-microm tracer particles. However, experimental results show that the 2-microm tracer particles stayed in the combined indoor air and surface compartments much longer (>19 days). Using a two-compartment model to simulate a regular deposition and resuspension cycle by normal human activity (e.g., walking and sitting on furniture), we estimated residence time for 2-microm conservative particulate pollutants to be more than 7 decades without vacuum cleaning, and months if vacuum cleaning was done once per week. This finding supports the observed long residence time of persistent organic pollutants in indoor environments. This study introduces a method to evaluate the particle resuspension rate from semicontinuous concentration data of particulate matter (PM). It reveals that resuspension and subsequent exfiltration does not strongly affect the overall residence time of PM pollutants when compared with surface cleaning. However, resuspension substantially increases PM concentration, and thus increases short-term inhalation exposure to indoor PM pollutants.     

Excimer laser fragmentation-fluorescence spectroscopy as a method for monitoring ammonium nitrate and ammonium sulfate particles

Excimer laser fragmentation-fluorescence spectroscopy (ELFFS) is shown to be an effective detection strategy for ammonium nitrate and ammonium sulfate particles at atmospheric pressure and room temperature. Following photofragmentation of the ammonium salt particle, fluorescence of the NH fragment is observed at 336 nm. The fluorescence signal is shown to depend linearly on particle surface area for laser intensities varying from 1.2 x 10(8) to 6 x 10(8) W/cm2. The 100 shot (1 s) detection limits for ammonium nitrate range from 20 ppb for 0.2 microm particles to 125 ppb for 0.8 microm particles, where these concentrations are expressed as moles of ammonium ion per mole of air. For ammonium sulfate, the 100 shot (1 s) detection limits vary from 60 ppb for 0.2 microm particles to 500 ppb for 1 microm particles. These detection limits are low enough to measure ammonium salt particles that form in the exhaust of combustion processes utilizing ammonia injection as a nitric oxide control strategy.     

The transformation of outdoor ammonium nitrate aerosols in the indoor environment

Recent studies associate particulate air pollution with adverse health effects; however, the exposure to indoor particles of outdoor origin is not well characterized, particularly for individual chemical species. We conducted a field study in an unoccupied, single-story residence in Clovis, California to provide data and analyses to address issues important for assessing exposure. We used real-time particle monitors both outdoors and indoors to quantify nitrate, sulfate, and carbon particulate matter of particle size 2.5 μm or less in diameter (PM-2.5). The results show that measured indoor ammonium nitrate concentrations were significantly lower than would be expected based solely on penetration and deposition losses. The additional reduction can be attributed to the transformation indoors of ammonium nitrate into ammonia and nitric acid gases, which are subsequently lost by deposition and sorption to indoor surfaces. A mass balance model that accounts for the kinetics of ammonium nitrate evaporation was able to reproduce measured indoor ammonium nitrate and nitric acid concentrations, resulting in a fitted value of the deposition velocity for nitric acid of 0.56 cm s⁻¹. The results indicate that indoor exposure to outdoor ammonium nitrate in Central Valley of California are small, and suggest that exposure assessments based on total particle mass measured outdoors may obscure the actual causal relationships for indoor exposure to particles of outdoor origin.     

The impact of particulates on the aqueous sonication of bromobenzene.

Sonodegradation of bromobenzene, bromophenolate ion, and 2,4,5-trichlorobiphenyl was studied in the presence of various types of solid particles suspended in water. Three particle diameters (10 nm, 15 microm, and 35 microm) and two particle types (silica particles and organic resin) were investigated over a range of particle concentrations (0.05-10 g l(-1)). The sonochemical decomposition rate constant for bromobenzene (k = 0.044 +/- 7.50 x 10(-4) min(-1) at 20 kHz) was not significantly impacted by very fine silica particles (10 nm). The presence of 15 microm silica decreased sonication rates slightly (<7%) even at a concentration of 10 g l(-1). Organic resin particles demonstrated a more significant impact, particularly at higher concentration and with very hydrophobic compounds. These findings are significant for the application of ultrasound to treatment streams containing solid particles.     

The interfacial mass transfer resistances of the ozone dry deposition over the field soil of Taichung County in Taiwan

This study aims to design a dry deposition chamber and to measure ozone depletion over the Taichung field soil. This study seeks to verify the phenomena by an experimental and mathematical model. It is demonstrated that interfacial mass transfer resistances of ozone dry deposition involve reactive resistance (R(sr)) and kinetic resistance (R(sk)). It reveals the chemical reaction (O3 + NO --> NO2) to produce the reactive resistance, and verifies that the interfacial mass transfer resistances depend on nitrogen oxide emission and soil temperature. It shows that the interfacial mass transfer resistances are reduced with increasing soil temperature (T(S)). The model profiles are smaller than the observed data within a relative error of 15%. The reactive resistance decreases exponentially with increasing soil temperature; R(sr)(-1) (cm x sec(-1)) = 0.0001 exp (0.1455T(S)). The kinetic resistance decreases linearly with increasing soil temperature; R(sk)(-1)(cm x sec(-1)) = 0.0108T(S) + 1.4012. This model is more accurate with higher soil temperature and larger ozone concentration. Results are consistent with thermodynamics and reaction kinetics. Ozone dry deposition over agricultural soil causes conversion of nitrogen oxide (NO) to nitrogen dioxide (NO2).     

Deposition rates on smooth surfaces and coagulation of aerosol particles inside a test chamber

Because aerosol particle deposition is an important factor in indoor air quality, many empirical and theoretical studies have attempted to understand the process. In this study, we estimated the deposition rate of aerosol particles on smooth aluminum surfaces inside a test chamber. We investigated the influence of turbulent intensity due to ventilation and fan operation. We also investigated two important processes in particle deposition: turbophoresis, which is significant for micron particles, and coagulation, which is relevant to ultrafine particles (UFP diameter <0.1 μm) at high particle concentrations. Our analysis included semi-empirical estimates of the deposition rates that were compared to available deposition models and verified with simulations of an aerosol dynamics model. In agreement with previous studies, this study found that induced turbulent intensity greatly enhanced deposition rates of fine particles (FP diameter <1 μm). The deposition rate of FP was proportional to the ventilation rate, and it increased monotonically with fan speed. With our setup, turbophoresis was very important for coarse particles larger than 5 μm. The coagulation of aerosol particles was insignificant when the particle concentration was less than 10⁴ cm^?3 during fan operation. The model simulation results verified that the aerosol dynamics module incorporated in our Multi-Compartment and Size-Resolved Indoor Aerosol Model (MC-SIAM) was valid. The behavior of aerosol particles inside our chamber was similar to that found in real-life conditions with the same ventilation rates (0.018–0.39 h^?1) and similar air mixing modes. Therefore, our findings provide insight into indoor particle behavior.     

Atmospheric dry deposition fluxes of trace elements measured in Bursa, Turkey

Trace element dry deposition fluxes were measured using a smooth, greased, knife-edge surrogate surface (KSS) holding greased Mylar strips in Bursa, Turkey. Sampling program was conducted between October 2002 and June 2003 and 46 dry deposition samples were collected. The average fluxes of crustal metals (Mg, Ca, and Fe) were one to four orders of magnitude higher than the fluxes of anthropogenic metals. Trace element fluxes ranged from 3 (Cd) to 24,230 (Ca) microg m(-2) d(-1). The average trace element dry deposition fluxes measured in this study were similar to those measured in other urban areas. In addition, ambient air samples were also collected simultaneously with flux samples and concentrations of trace elements, collected with a TSP sampler, were between 0.7 and 4900 ng m(-3) for Cd and Ca, respectively. The overall trace element dry deposition velocities, calculated by dividing the fluxes to the particle phase concentrations ranged from 2.3+/-1.7 cm s(-1) (Pb) to 11.1+/-6.4 cm s(-1) (Ni). These values are in good agreement with the values calculated using similar techniques. The anthropogenic and crustal contributions were estimated by employing enrichment factors (EFs) calculated relative to the average crustal composition. Low EFs for dry deposition samples were calculated. This is probably due to contamination of local dust and its important contribution to the collected samples.     

The influence of feeding, photoperiod and selected solvents on the reproductive strategies of the water flea, Daphnia magna

The influence of different feeding rates, reduced photoperiod and ethanol and acetone exposure on male production in Daphnia magna was investigated. Male production was observed under reduced photoperiod (8-h light:16-h dark) in all food levels. However, the sex ratio of daphnids fed 1x10(6) algae cells increased significantly from that of daphnids fed 15x10(6) algae cells (0.486+/-0.059 and 0.271+/-0.027, respectively). Under normal photoperiod (16-h light:8-h dark) and low food conditions (3.75x10(6) algae cells), a statistically significant increase in the sex ratio was observed in daphnids exposed to acetone at EPA acceptable solvent limits (0.1 ml/l). A shift back to parthenogenetic reproduction was observed in acetone-exposed daphnids at high food levels (15x10(6) algae cells). The results indicate that the reproductive strategies of females are influenced by phenological (i.e. reduced photoperiod), dietary and exogenous chemical cues.     

Environmental tobacco smoke particles in multizone indoor environments

Environmental tobacco smoke (ETS) is a major source of human exposure to airborne particles. To better understand the factors that affect exposure, and to investigate the potential effectiveness of technical control measures, a series of experiments was conducted in a two-room test facility. Particle concentrations, size distributions, and airflow rates were measured during and after combustion of a cigarette. Experiments were varied to obtain information about the effects on exposure of smoker segregation, ventilation modification, and air filtration. The experimental data were used to test the performance of an analytical model of the two-zone environment and a numerical multizone aerosol dynamics model. A respiratory tract particle deposition model was also applied to the results to estimate the mass of ETS particles that would be deposited in the lungs of a nonsmoker exposed in either the smoking or nonsmoking room. Comparisons between the experimental data and model predictions showed good agreement. For time-averaged particle mass concentration, the average bias between model and experiments was less than 10%. The average absolute error was typically 35%, probably because of variability in particle emission rates from cigarettes. For the conditions tested, the use of a portable air filtration unit yielded 65–90% reductions in predicted lung deposition relative to the baseline scenario. The use of exhaust ventilation in the smoking room reduced predicted lung deposition in the nonsmoking room by more than 80%, as did segregating the smoker from nonsmokers with a closed door.     

Measurements of Ultrafine Particles and Other Vehicular Pollutants inside a Mobile Exposure System on Los Angeles Freeways

Abstract

A mobile exposure and air pollution measurement system was developed and used for on-freeway ultrafine particle health effects studies. A nine-passenger van was modified with a high-efficiency particulate air (HEPA) filtration system that can deliver filtered or unfiltered air to an exposure chamber inside the van. State-of-the-art instruments were used to measure concentration and size distribution of fine and ultrafine particles and the concentration of carbon monoxide (CO), black carbon (BC), particle-bound polycyclic aromatic hydrocarbons (PAHs), fine particulate matter (PM_2.5) mass, and oxides of nitrogen (NO_x) inside the exposure chamber. This paper presents the construction and technical details of the van and air pollutant concentrations collected in 32 2-hr runs on two major Los Angeles freeways, Interstate 405 (I-405; mostly gasoline traffic) and Interstate 710 (I-710; large proportion of heavy-duty diesel traffic). More than 97% of particles were removed when the flow through the filter box was switched from bypass mode to filter mode while the vehicle was driving on both freeways. The filtration system thus provides a great particulate matter exposure contrast while keeping gas-phase pollutant concentrations the same. Under bypass mode, average total particle number concentration observed inside the exposure chamber was around 8.4 × 10⁴ and 1.3 × 10⁵ particles cm^-3 on the I-405 and the I-710 freeways, respectively. Bimodal size distributions were consistent and similar for both freeways with the first mode around 16–20 nm and the second mode around 50–55 nm. BC and particle-bound PAH concentrations were more than two times greater on the I-710 than on the I-405 freeway. Very weak correlations were observed between total particle number concentrations and other vehicular pollutants on the freeways.