Intercomparison of the measurements of oxalic acid in aerosols by gas chromatography and ion chromatography

Oxalate, the anion of oxalic acid, is one of the most abundant measurable organic species in atmospheric aerosols. Traditionally, this bifunctional species has been measured by gas chromatography (GC) after derivatization to butyl ester and by ion chromatography (IC) without derivatization. However, there are few published comparisons of the two techniques. Here, we report the results of an intercomparison study for the measurement of oxalic acid in Arctic aerosols (<2.5 μm, n = 82) collected in 1992 using GC and IC. The concentrations of oxalic acid by GC ranged from 6.5–59.1 ng m^?3 (av. 26.0 ng m^?3, median 26.2 ng m^?3) whereas those by IC ranged from 6.6–52.1 ng m^?3 (av. 26.6 ng m^?3, median 25.4 ng m^?3). They showed a good correlation (r = 0.84) with a slope of 0.96. Thus, observations of oxalate obtained by GC employing dibutyl esters are almost equal to those by IC. Because the accuracy of oxalic acid by GC method largely depends on the method used, it is important to strictly examine the recovery in each study.     

SOA from methylglyoxal in clouds and wet aerosols: Measurement and prediction of key products

Aqueous OH radical oxidation of methylglyoxal in clouds and wet aerosols is a potentially important global and regional source of secondary organic aerosol (SOA). We quantify organic acid products of the aqueous reaction of methylglyoxal (30–3000 μM) and OH radical (approx. 4 × 10^?12 M), model their formation in the reaction vessel and investigate how the starting concentrations of precursors and the presence of acidic sulfate (0–840 μM) affect product formation. Predicted products were observed. The predicted temporal evolution of oxalic acid, pyruvic acid and total organic carbon matched observations at cloud relevant concentrations (30 μM), validating this methylglyoxal cloud chemistry, which is currently being implemented in some atmospheric models of SOA formation. The addition of sulfuric acid at cloud relevant concentrations had little effect on oxalic acid yields. At higher concentrations (3000 μM), predictions deviate from observations. Larger carboxylic acids (≥C₄) and other high molecular weight products become increasingly important as concentration increases, suggesting that small carboxylic acids are the major products in clouds while larger carboxylic acids and oligomers are important products in wet aerosols.     

Determination of primary and secondary sources of organic acids and carbonaceous aerosols using stable carbon isotopes

Stable carbon isotope ratio (δ¹³C) data can provide important information regarding the sources and the processing of atmospheric organic carbon species. Formic, acetic and oxalic acid were collected from Zurich city in August–September 2002 and March 2003 in the gas and aerosol phase, and the corresponding δ¹³C analysis was performed using a wet oxidation method followed by isotope ratio mass spectrometry. In August, the δ¹³C values of gas phase formic acid showed a significant correlation with ozone (coefficient of determination (r²) = 0.63) due to the kinetic isotope effect (KIE). This indicates the presence of secondary sources (i.e. production of organic acids in the atmosphere) in addition to direct emission. In March, both gaseous formic and acetic acid exhibited similar δ¹³C values and did not show any correlation with ozone, indicating a predominantly primary origin. Even though oxalic acid is mainly produced by secondary processes, the δ¹³C value of particulate oxalic acid was not depleted and did not show any correlation with ozone, which may be due to the enrichment of ¹³C during the gas - aerosol partitioning.The concentrations and δ¹³C values of the different aerosol fractions (water soluble organic carbon, water insoluble organic carbon, carbonate and black carbon) collected during the same period were also determined. Water soluble organic carbon (WSOC) contributed about 60% to the total carbon and was enriched in ¹³C compared to other fractions indicating a possible effect of gas - aerosol partitioning on δ¹³C of carbonaceous aerosols. The carbonate fraction in general was very low (3% of the total carbon).     

Chemical characteristics of organic aerosols in Algiers city area: influence of a fat manufacture plant

Total concentrations and homologue distributions of organic fraction constituents have been determined in particulate matter emitted from different units of a fat manufacturer (i.e. oils refining and conditioning plants, and production and conditioning units of a soap industry) located in Algiers area, as well as in atmospheric aerosols. In particular n-alkanes, n-alkanoic and n-alkenoic acids, n-alkan-2-ones and polycyclic aromatic hydrocarbons (PAH) were investigated. Organic aerosol contents varied broadly among the plant units, depending upon nature of the manufactured products. The percent composition of all classes of compounds investigated in ambient atmosphere was similar to those observed indoor at industrial plant units. Organic acids, n-alkanoic as well as n-alkenoic, appeared by far the most abundant organic constituents of aerosols, both indoor and outdoor, ranging from 7.7 to 19.8 and from 12.7 to 17.1 μg m⁻³, respectively. The huge occurrence of acids and n-alkanes in ambient aerosols was consistent with their high levels present in oil and fat materials. Among minor components of aerosols, n-alkan-2-ones and PAH, seemed to be related to thermally induced ageing and direct combustion of raw organic material used for oil and soap production.     

Redox activity of urban quasi-ultrafine particles from primary and secondary sources

To characterize the redox activity profiles of atmospheric aerosols from primary (traffic) and secondary photochemical sources, ambient quasi-ultrafine particles were collected near downtown Los Angeles in two different time periods – morning (6:00–9:00 PDT) and afternoon (11:00–14:00 PDT) in the summer of 2008. Detailed chemical analysis of the collected samples, including water-soluble elements, inorganic ions, organic species and water soluble organic carbon (WSOC) was conducted and redox activity of the samples was measured by two different assays: the dithiothreitol (DTT) and the macrophage reactive oxygen species (ROS) assays. Tracers of secondary photochemical reactions, such as sulfate and organic acids were higher (2.1 ± 0.6 times for sulfate, and up to 3 times for the organic acids) in the afternoon period. WSOC was also elevated by 2.5 ± 0.9 times in the afternoon period due to photo-oxidation of primary particles during atmospheric aging. Redox activity measured by the DTT assay was considerably higher for the samples collected during the afternoon; on the other hand, diurnal trends in the ROS-based activity were not consistent between the morning and afternoon periods. A linear regression between redox activity and various PM chemical constituents showed that the DTT assay was highly correlated with WSOC (R² = 0.80), while ROS activity was associated mostly with water soluble transition metals (Vanadium, Nickel and Cadmium; R² > 0.70). The DTT and ROS assays, which are based on the generation of different oxidizing species by chemical PM constituents, provide important information for elucidating the health risks related to PM exposure from different sources. Thus, both primary and secondary particles possess high redox activity; however, photochemical transformations of primary emissions with atmospheric aging enhance the toxicological potency of primary particles in terms of generating oxidative stress and leading to subsequent damage in cells.     

Characterization and sources assignation of PM2.5 organic aerosol in a rural area of Spain

The results from a year-long study of the organic composition of PM2.5 aerosol collected in a rural area influenced by a highway of Spain are reported. The lack of prior information related to the organic composition of PM2.5 aerosol in Spain, concretely in rural areas, led definition of the goals of this study. As a result, this work has been able to characterize the main organic components of atmospheric aerosols, including several compounds of SOA, and has conducted a multivariate analysis in order to assign sources of particulate matter. A total of 89 samples were taken between April 2004 and April 2005 using a high-volume sampler. Features and abundance of n-alkanes, polycyclic aromatic hydrocarbons (PAHs), alcohols and acids were separately determined using gas chromatography/mass spectrometry and high performance liquid chromatography analysis. The Σn-alkane and ΣPAHs ranged from 3 to 81 ng m^?3 and 0.1 to 6 ng m^?3 respectively, with higher concentrations during colder months. Ambient concentrations of Σalcohols and Σacids ranged from 21 to 184 ng m^?3 and 39 to 733 ng m^?3, respectively. Also, several components of secondary organic aerosol have been quantified, confirming the biogenic contribution to ambient aerosol. In addition, factor analysis was used to reveal origin of organic compounds associated to particulate matter. Eight factors were extracted accounting more than 83% of the variability in the original data. These factors were assigned to a typical high pollution episode by anthropogenic particles, crustal material, plant waxes, fossil fuel combustion, temperature, microbiological emissions, SOA and dispersion of pollutants by wind action. Finally, a cluster analysis was used to compare the organic composition between the four seasons.     

Carbonaceous and inorganic composition in long-range transported aerosols over northern Japan: Implication for aging of water-soluble organic fraction

To better understand the influence of sources and atmospheric processing on aerosol chemical composition, we collected atmospheric particles in Sapporo, northern Japan during spring and early summer 2005 under the air mass transport conditions from Siberia, China and surrounding seas. The aerosols were analyzed for inorganic ions, organic carbon (OC), elemental carbon (EC), water-soluble organic carbon (WSOC), and the major water-soluble organic compound classes (i.e., dicarboxylic acids and sugars). SO₄^2? is the most abundant inorganic constituent (average 44% of the identified inorganic ion mass) followed by NH₄⁺ (21%) and NO₃^? (13%). Concentrations of OC, EC, and WSOC ranged from 2.0–16, 0.24–2.9, and 0.80–7.9 μg m^?3 with a mean of 7.4, 1.0, and 3.1 μg m^?3, respectively. High OC/EC ratios (range: 3.6–19, mean: 8.7) were obtained, however WSOC/OC ratios (0.23–0.69, 0.44) do not show any significant diurnal changes. These results suggest that the Sapporo aerosols were already aged, but were not seriously affected by local photochemical processes. Identified water-soluble organic compounds (diacids + sugars) account for <10% of WSOC. Based on some marker species and air mass back trajectory analyses, and using stable carbon isotopic compositions of shorter-chain diacids (i.e., C₂–C₄) as photochemical aging factor of organic aerosols, the present study suggests that a fraction of WSOC in OC is most likely influenced by aerosol aging, although the OC loading in aerosols may be more influenced by their sources and source regions.     

Carbon content of common airborne fungal species and fungal contribution to aerosol organic carbon in a subtropical city

Interest in the role and contribution of fungi to atmospheric aerosols and processes grows in the past decade. Substantial data or information such as fungal mass or carbon loading to ambient aerosols is however still lacking. This study aimed to quantify the specific organic carbon content (OC per spore) of eleven fungal species commonly found airborne in the subtropics, and estimated their contribution to organic carbon in aerosols. The specific OC contents showed a size-dependent relationship (r = 0.64, p < 0.05) and ranged from 3.6 to 201.0 pg carbon per spore or yeast cell, giving an average of 6.0 pg carbon per spore (RSD 51%) for spore or cell size less than 10 μm. In accounting for natural variations in the composition and abundance of fungal population, weighted-average carbon content for field samples was adopted using the laboratory determined specific OC values. An average of 5.97 pg carbon per spore (RSD 3.8%) was enumerated from 28 field samples collected at the university campus. The mean fungal OC concentration was 3.7, 6.0 and 9.7 ng m^?3 in PM_2.5, PM_2.5–10 and PM₁₀, respectively. These corresponded to 0.1%, 1.2% and 0.2% of the total OC in PM_2.5, PM_2.5–10 and PM₁₀, respectively. In the study period, rain provided periods with low total OC but high fungal prevalence and fungi contributed 7–32% OC in PM_2.5–10 or 2.4–7.1% OC in PM₁₀. More extensive studies are deserved to better understand the spatial-, temporal- and episodic dependency on the fungal OC contribution to the atmospheric aerosols.     

Interaction of nitrogen dioxide (NO2) with a monolayer of oleic acid at the air–water interface – A simple proxy for atmospheric aerosol

The reactions between atmospheric oxidants and organic amphiphiles at the air–water interface of an aerosol droplet may affect the size and critical supersaturation required for cloud droplet formation. We demonstrate that no reaction occurs between gaseous nitrogen dioxide (1000 ppm in air) and a monolayer of an insoluble amphiphile, oleic acid (cis-9-octadecenoic acid), at the air–water interface which removes material from the air–water interface. We present evidence that the NO₂ isomerises the cis-9-octadecenoic (oleic) acid to trans-9-octadecenoic (elaidic) acid. The study presented here is important for future and previous studies of (1) the reaction between the nitrate radical, NO₃, and thin organic films as NO₂ is usually present in high concentrations in these experimental systems and (2) the effect of NO₂ air pollution on the unsaturated fatty acids and lipids found at the air–liquid surface of human lung lining fluid.     

Origin of low-molecular-weight dicarboxylic acids and their concentration and size distribution variation in suburban aerosol

The concentrations and size distributions of low molecular weight dicarboxylic acids in suburban particulate matter collected in early and mid-autumn 2002 and early and mid-summer 2003 in Tainan, Taiwan, were analyzed. PM_2.5 contained, on average, 449.3 ng m⁻³ oxalic acid, 53.0 ng m⁻³ malic acid, 45.5 ng m⁻³ maleic acid, 29.6 ng m⁻³ succinic acid, 20.8 ng m⁻³ malonic acid, and 11.6 ng m⁻³ tartaric acid. Bar tartaric acid, concentrations were higher during the day, indicating that these acids are photochemical products. Furthermore, the malonic acid–succinic acid ratio of 0.79 during daytime and 0.60 during nighttime demonstrates that more succinic acid is converted to malonic acid during daytime, and that aerosol dicarboxylic acids predominantly originate from photochemical oxidation during daytime. The concentration peak of oxalic acid occurred in the condensation and droplet modes (0.32–1.0 μm), as did that of sulfate. In early summer, succinic acid, malonic acid, and oxalic acid major concentration peaks occurred at 0.32–0.54 μm, indicative of the relationship created by photochemical decomposition of succinc acid into malonic acid into oxalic acid. This photochemical decomposition accelerated in mid-summer such that most concentration peaks for succinic and malonic acids also occurred at 0.32–1.0 μm. Mid-summer is also the wettest period of the four in Tainan, with 85% RH. As a result of hygroscopic reactions in mid-summer, malonic acid and oxalic acid major concentration peaks shifted from 0.32–0.54 μm or 0.54–1.0 μm to 1.0–1.8 μm, thus extending the range in which these species were found to larger particle sizes, and this shift was highly correlated with a shift in succinic acid size distribution. This latter observation offers additional evidence that succinic acid is photochemically decomposed into malonic acid and oxalic acid and that the presence of malonic and oxalic acids in the wet mid-summer atmosphere is made more obvious via hygroscopic growth. Close correlation between succinic acid and Na⁺ and succinic acid and NO₃⁻ in the coarse mode is related to sea spray.     

Investigation of the time evolved spatial distribution of urban PM2.5 concentrations and aerosol composition during episodic high PM events in Yuma,AZ

An interdisciplinary field study designed to investigate the spatial and temporal variability of atmospheric aerosols during high particulate matter (PM) events along the US–Mexico border near Yuma, AZ was run during the week of March 18, 2007. The experiments were designed to quantify chemical composition and physical phenomena governing the transport of aerosols generated from episodic high PM events. The field study included two micrometeorological monitoring sites; one rural and one urban, equipped with sonic anemometers, continuous particulate concentration monitors and ambient aerosol collection equipment. In addition to the two main monitoring sites, five additional locations were equipped with optical particle counters to allow for the investigation of the spatial and temporal distribution of PM_2.5 in the urban environment. In this paper, the meteorological and turbulence parameters governing the distribution and concentration of PM_2.5 in the urban environment for two high-wind erosion events and one burning event are compared. The interaction between local atmospheric conditions and the particulate distribution is investigated. Results indicate that a single point measurement in the urban area of Yuma may not be sufficient for determining the ambient PM concentrations that the local population experiences; all three high PM events indicated PM_2.5 varied considerably with maximum urban concentrations 5–10 times greater than the measured minima. A comparison of inorganic and carbonaceous content of the aerosols for the three high PM events is presented. The comparison shows an increase in silicon during crustal dust events and an increase in elemental and organic carbon during the burn event. Additional surface chemistry analysis, using time-of-flight secondary ion mass spectrometry (ToF-SIMS), for aerosols collected at the urban and rural sites during the burn event are discussed. The surface chemistry analysis provides positive ion mass spectra of organic and inorganic species in the ambient aerosol, and can be used to determine the type of combustion process that contributed to an increase in PM concentration during the burn event.     

Identification of dicarboxylic acids and aldehydes of PM10 and PM2.5 aerosols in Nanjing,China

In this study aerosol samples of PM10 and PM2.5 collected from 18 February 2001 to 1 May 2001 in Nanjing, China were analyzed for their water-soluble organic compounds. A series of homologous dicarboxylic acids (C_2–10) and two kinds of aldehydes (methylglyoxal and 2-oxo-malonaldehyde) were detected by GC and GC/MS. Among the identified compounds, the concentration of oxalic acid was the highest at all the five sites, which ranged from 178 to 1423 ng/m³. The second highest concentration of dicarboxylic acids were malonic and succinic acids, which ranged from 26.9 to 243 ng/m³. Higher level of azelaic acid was also observed, of which the maximum was 301 ng/m³. As the highest fraction of dicarboxylic acids, oxalic acid comprised from 28% to 86% of total dicarboxylic acids in PM10 and from 41% to 65% of total dicarboxylic acids in PM2.5. The dicarboxylic acids (C₂, C₃, C₄) together accounted for 38–95% of total dicarboxylic acids in PM10 and 59–87% of dicarboxylic acids in PM2.5. In this study, the total dicarboxylic acids accounted for 2.8–7.9% of total organic carbon (TOC) of water-soluble matters for PM10 and 3.4–11.8% of TOC for PM2.5. All dicarboxylic acids detected in this study together accounted for about 1% of particle mass. The concentration of azelaic acid was higher at one site than others, which may be resulted from higher level of volatile fat used for cooking. The amounts of dicarboxyic acids (C_2,3,4,9) and 2-oxo-malonaldehyde of PM2.5 were higher in winter and lower in spring. Compared with other major metropolitans in the world, the level of oxalic acid concentration of Nanjing is much higher, which may be contributed to higher level of particle loadings, especially for fine particles.     

Comparison of organic compositions in dust storm and normal aerosol samples collected at Gosan,Jeju Island,during spring 2005

To better understand the current physical and chemical properties of East Asian aerosols, an intensive observation of atmospheric particles was conducted at Gosan site, Jeju Island, South Korea during 2005 spring. Total suspended particle (TSP) samples were collected using pre-combusted quartz filters and a high-volume air sampler with the time intervals ranging from 3 h to 48 h. The kinds and amount of various organic compounds were measured in the samples using gas chromatography–mass spectrometry. Among the 99 target compounds detected, saccharides (average, 130 ± 14 ng m^?3), fatty acids (73 ± 7 ng m^?3), alcohols (41 ± 4 ng m^?3), n-alkanes (32 ± 3 ng m^?3), and phthalates (21 ± 2 ng m^?3) were found to be major compound classes with polyols/polyacids, lignin and resin products, PAHs, sterols and aromatic acids being minor. Compared to the previous results reported for 2001 late spring samples, no significant changes were found in the levels of their concentrations and compositions for 4 years, although the economy in East Asia, especially in China, has sharply expanded from 2001 to 2005. During the campaign at Gosan site, we encountered two distinct dust storm episodes with high TSP concentrations. The first dust event occurred on March 28, which was characterized by a predominance of secondary organic aerosols. The second event that occurred on the next day (March 29) was found to be characterized by primary organic aerosols associated with forest fires in Siberia/northeastern China. A significant variation in the molecular compositions, which was found within a day, suggests that the compositions of East Asian aerosols are heterogeneous due to multi-contributions from different source regions together with different pathways of long-range atmospheric transport of particles.     

Contributions of biogenic volatile organic compounds to the formation of secondary organic aerosols over Mt. Tai,Central East China

To better understand the contribution of biogenic volatile organic compounds to the formation of secondary organic aerosol (SOA) in high mountain regions, ambient aerosols were collected at the summit of Mt. Tai (1534 m, a.s.l.), Central East China (CEC) during the Mount Tai Experiment 2006 campaign (MTX2006) in early summer. Biogenic SOA tracers for the oxidation of isoprene, α/β-pinene, and β-caryophyllene were measured using gas chromatography/mass spectrometry. Most of the biogenic SOA tracers did not show clear diurnal variations, suggesting that they are formed during long-range atmospheric transport or over relatively long time scales. Although isoprene- and α/β-pinene-derived SOA tracers did not correlate with levoglucosan (a biomass burning tracer), β-caryophyllinic acid showed a good correlation with levoglucosan, indicating that crop residue burning may be a source for this acid. Total concentrations of isoprene oxidation products are much higher than those of α/β-pinene and β-caryophyllene oxidation products. The averaged ratio of isoprene to α/β-pinene oxidation products (R_iso/pine) was 4.9 and 6.7 for the daytime and nighttime samples, respectively. These values are among the highest in the aerosols reported in different geographical regions, which may be due to the large isoprene fluxes and relatively high levels of oxidants such as OH in CEC. Using a tracer-based method, we estimated the concentrations of secondary organic carbon (SOC) derived from isoprene, α/β-pinene, and β-caryophyllene to be 0.42–3.1 μgC m^?3 (average 1.6 μgC m^?3) during the daytime and 0.11–4.2 μgC m^?3 (1.7 μgC m^?3) during the nighttime. These values correspond to 2.9–23% (10%) and 3.2–28% (9.8%) of the total OC concentrations, in which isoprene-derived SOC accounts for 58% and 63% of total SOC during the daytime and nighttime, respectively. This study suggests that isoprene is a more significant precursor for biogenic SOA than α/β-pinene and β-caryophyllene at high altitudes in CEC.     

Quantification and radiocarbon source apportionment of black carbon in atmospheric aerosols using the CTO-375 method

To make progress towards linking the atmosphere and biogeosphere parts of the black carbon (BC) cycle, a chemothermal oxidation method (CTO-375), commonly applied for isolating BC from complex geomatrices such as soils, sediments and aquatic particles, was applied to investigate the BC also in atmospheric particles. Concentrations and ¹⁴C-based source apportionment of CTO-375 based BC was established for a reference aerosol (NIST RM-8785) and for wintertime aerosols collected in Stockholm and in a Swedish background area. The results were compared with thermal–optical (OC/EC) measurements. For NIST RM-8785, a good agreement was found between the BC_CTO-375 concentration and the reported elemental carbon (EC) concentration measured by the “Speciation Trends Network—National Institute of Occupational Safety and Health” method (EC_NIOSH) with BC_CTO-375 of 0.054±0.002 g g⁻¹ and EC_NIOSH of 0.067±0.008 g g⁻¹. In contrast, there was an average factor of ca. 20 difference between BC_CTO-375 and EC_NIOSH for the ambient Scandinavian wintertime aerosols, presumably reflecting a combination of BC_CTO-375 isolating only the recalcitrant soot-BC portion of the BC continuum and the EC_NIOSH metric inadvertently including some intrinsically non-pyrogenic organic matter. Isolation of BC_CTO-375 with subsequent off-line radiocarbon analysis yielded fraction modern values (fM) for total organic carbon (TOC) of 0.93 (aerosols from a Swedish background area), and 0.58 (aerosols collected in Stockholm); whereas the fM for BC_CTO-375 isolates were 1.08 (aerosols from a Swedish background area), and 0.87 (aerosols collected in Stockholm). This radiocarbon-based source apportionment suggests that contribution from biomass combustion to cold-season atmospheric BC_CTO-375 in Stockholm was 70% and in the background area 88%.     

The continuous field measurements of soluble aerosol compositions at the Taipei Aerosol Supersite,Taiwan

The characteristics of ambient aerosols, affected by solar radiation, relative humidity, wind speed, wind direction, and gas–aerosol interaction, changed rapidly at different spatial and temporal scales. In Taipei Basin, dense traffic emissions and sufficient solar radiation for typical summer days favored the formation of secondary aerosols. In winter, the air quality in Taipei Basin was usually affected by the Asian continental outflows due to the long-range transport of pollutants carried by the winter monsoon. The conventional filter-based method needs a long time for collecting aerosols and analyzing compositions, which cannot provide high time-resolution data to investigate aerosol sources, atmospheric transformation processes, and health effects. In this work, the in situ ion chromatograph (IC) system was developed to provide 15-min time-resolution data of nine soluble inorganic species (Cl⁻, NO₂⁻, NO₃⁻, SO₄²⁻, Na⁺, NH₄⁺, K⁺, Mg²⁺ and Ca²⁺). Over 89% of all particles larger than approximately 0.056 μm were collected by the in situ IC system. The in situ IC system is estimated to have a limit of detection lower than 0.3 μg m⁻³ for the various ambient ionic components. Depending on the hourly measurements, the pollutant events with high aerosol concentrations in Taipei Basin were associated with the local traffic emission in rush hour, the accumulation of pollutants in the stagnant atmosphere, the emission of industrial pollutants from the nearby factories, the photochemical secondary aerosol formation, and the long-range transport of pollutants from Asian outflows.     

Organic Matter of the Troposphere—II.: Natural Background of biogenic lipid matter in aerosols over the rural western United States

Higher plant waxes are the predominant natural components in the lipid fractions (> C₁₅) of aerosols sampled over rural and oceanic regions. Hydrocarbon, fatty acid, ketone and fatty alcohol fractions of the lipids were characterized in terms of their contents of homologous compound series and specific biogenic molecular markers. Particulate samples from the rural western United States have been analyzed and compared with samples from urban Los Angeles and remote areas over the Atlantic Ocean. The samples from rural sites contained predominantly vascular plant wax and lesser amounts of higher plant sterols and resin residues. Urban samples and, to varying degrees, some rural samples contained primarily higher weight residues of petroleum products. The loadings of hydrocarbons derived from higher plant waxes ranged approximately from 10 to 160 ng m⁻³ of air (for fatty acids, 10–100 ng m⁻³ and for fatty alcohols, 10–200 ng m⁻³). Higher molecular weight lipids (i.e. plant epicuticular wax, terpenes, etc.) from flora comprise a significant component of the organic carbon in rural aerosols. Primary biogenic residues are major components of aerosols in all areas and they are important components in the global cycling of organic carbon.     

Photochemical production and loss of organic acids in high Arctic aerosols during long-range transport and polar sunrise ozone depletion events

Unique daily measurements of water-soluble organics in fine (<2 μm) and coarse (>2 μm) aerosols were conducted at Alert in the Canadian Arctic in winter to spring of 1992. They yield insight into photochemical production and loss of organics during long-range transport and ozone depletion events following polar sunrise. Comprehensive analyses of α, ω-dicarboxylic acids (C₂–C₁₂), ω-oxocarboxylic acids (C₂–C₉) and α-dicarbonyls (C₂, C₃) as well as pyruvic acid and aromatic (phthalic) diacid were conducted using GC and GC/MS techniques. Oxalic (C₂) acid was generally the dominant diacid species in both fine and coarse fractions, followed by malonic (C₃) and succinic (C₄) acids. Concentrations of total diacids in the fine aerosol fraction (0.2–64 ng m⁻³) were 5–60 times higher than those in the coarse fraction (0.01–3 ng m⁻³). After polar sunrise in early-March, the total concentration of fine aerosol diacids increased by a factor of 3–5 while the coarse mode did not change significantly. From dark winter to sunlit spring, temporal changes in correlations and ratios of these water-soluble organics to vanadium and sulfate measured simultaneously suggest that atmospheric diacids and related organic compounds are largely controlled by long-range atmospheric transport of polluted air during winter, but they are significantly affected by photochemical production. The latter can occur in sunlight either during transport to the Arctic or during photochemical events associated with surface ozone depletion and bromine chemistry near Alert in spring. Conversion of gaseous precursors to particulate matter via photochemical oxidation was intensified at polar sunrise, resulting in a peak in the ratio of total diacids to V. During ozone depletion events, complex patterns are indicated in photochemical production and loss depending on the diacid compound. Unsaturated (maleic and phthalic) diacids were inversely correlated with particulate Br whereas saturated diacids (C₂–C₄) positively correlated with particulate Br. These results suggest that Br chemistry associated with ozone depletion leads to degradation of unsaturated diacids and to the production of smaller saturated diacids.     

Physicochemical variations in atmospheric aerosols recorded at sea onboard the Atlantic–Mediterranean 2008 Scholar Ship cruise (Part I): Particle mass concentrations,size ratios,and main chemical components

We report on ambient atmospheric aerosols present at sea during the Atlantic–Mediterranean voyage of Oceanic II (The Scholar Ship) in spring 2008. A record was obtained of hourly PM₁₀, PM_2.5, and PM₁ particle size fraction concentrations and 24-h filter samples for chemical analysis which allowed for comparison between levels of crustal particles, sea spray, total carbon, and secondary inorganic aerosols. On-board monitoring was continuous from the equatorial Atlantic to the Straits of Gibraltar, across the Mediterranean to Istanbul, and back via Lisbon to the English Channel. Initially clean air in the open Atlantic registered PM₁₀ levels <10 μg m^?3 but became progressively polluted by increasingly coarse PM as the ship approached land. Away from major port cities, the main sources of atmospheric contamination identified were dust intrusions from North Africa (NAF), smoke plumes from biomass burning in sub-Saharan Africa and Russia, industrial sulphate clouds and other regional pollution sources transported from Europe, sea spray during rough seas, and plumes emanating from islands. Under dry NAF intrusions PM₁₀ daily mean levels averaged 40–60 μg m^?3 (30–40 μg m^?3 PM_2.5; c. 20 μg m^?3 PM₁), peaking briefly to >120 μg m^?3 (hourly mean) when the ship passed through curtains of higher dust concentrations amassed at the frontal edge of the dust cloud. PM₁/PM₁₀ ratios ranged from very low during desert dust intrusions (0.3–0.4) to very high during anthropogenic pollution plume events (0.8–1).     

Secondary organic aerosol formation from the oxidation of aromatic hydrocarbons in the presence of dry submicron ammonium sulfate aerosol

A laboratory study was conducted to examine formation of secondary organic aerosols. A smog chamber system was developed for studying gas–aerosol interactions in a dynamic flow reactor. These experiments were conducted to investigate the fate of gas and aerosol phase compounds generated from hydrocarbon–nitrogen oxide (HC/NO_x) mixtures irradiated in the presence of fine (<2.5 μm) particulate matter. The goal was to determine to what extent photochemical oxidation products of aromatic hydrocarbons contribute to secondary organic aerosol formation through uptake on pre-existing inorganic aerosols in the absence of liquid water films. Irradiations were conducted with toluene, p-xylene, and 1,3,5-trimethylbenzene in the presence of NO_x and ammonium sulfate aerosol, with propylene added to enhance the production of radicals in the system. The secondary organic aerosol yields were determined by dividing the mass concentration of organic fraction of the aerosol collected on quartz filters by the mass concentration of the aromatic hydrocarbon removed by reaction. The mass concentration of the organic fraction was obtained by multiplying the measured organic carbon concentration by 2.0, a correction factor that takes into account the presence of hydrogen, nitrogen, and oxygen atoms in the organic species. The mass concentrations of ammonium, nitrate, and sulfate concentrations as well as the total mass of the aerosols were measured. A reasonable mass balance was found for each of the aerosols. The largest secondary organic aerosol yield of 1.59±0.40% was found for toluene at an organic aerosol concentration of 8.2 μm⁻³, followed by 1.09±0.27% for p-xylene at 6.4 μg m⁻³, and 0.41±0.10% for 1,3,5-trimethylbenzene at 2.0 μg m⁻³. In general, these results agree with those reported by Odum et al. and appear to be consistent with the gas–aerosol partitioning theory developed by Pankow. The presence of organic in the aerosol did not affect significantly the hygroscopic properties of the aerosol.