粉煤灰和纤维陶粒重金属浸出特性研究

以粉煤灰、作物秸秆、外加药剂为试验材料经多重工序制得秸秆-粉煤灰纤维陶粒(简称"纤维陶粒"),为考察其作为水处理滤料的安全性,以原灰作对比,测定了粉煤灰及纤维陶粒中8种重金属(Hg、As、Cd、Cr、Cu、Zn、Pb、Ni)质量比,并通过浸出试验分析其浸出特性。结果表明,纤维陶粒中8种重金属质量比均低于原灰,二者重金属质量比从大到小顺序均为Ni、Cr、Cu、Pb、Zn、As、Cd、Hg。除Zn外,原灰重金属浸出量随浸出时间总体呈增加趋势,浸出量从大到小依次为Pb、Ni、Cu、Zn、Cr、As、Cd、Hg;纤维陶粒重金属浸出量随浸出时间整体呈增大趋势,浸出量从大到小依次为Pb、Ni、Cd、Cu、Zn、Cr、As、Hg,与原灰相比增加量减少。纤维陶粒浸出液中各重金属浸出量均低于原灰,Hg、As、Cd、Cr、Cu、Zn、Pb、Ni平均浸出量分别占原灰的56.14%、55.92%、86.17%、64.17%、47.50%、99.51%、40.74%、58.93%。原灰重金属最大浸出率从大到小为Hg、Cd、Pb、As、Zn、Ni、Cu、Cr;纤维陶粒重金属最大浸出率从大到小为Hg、Cd、Pb、As、Ni、Zn、Cu、Cr,Hg和Cr分别为最易和最难浸出重金属。与原灰相比,纤维陶粒中8种重金属质量比、重金属浸出量和最大浸出率均有所降低,能在一定程度上减少重金属向水溶液中的浸出,提高了其作为水处理滤料的安全性。     

河南省武陟县大田土壤重金属形态分布及潜在生态风险评价

为了解河南省武陟县大田土壤重金属Cr、Cd、Pb、As、Cu、Se、Ni和Co的形态分布和生态风险情况,在该区域采集了12个表层土壤(0～20cm)样品,采用修正的BCR连续提取法进行形态分析,探讨其生物有效性,并采用Hakanson指数法评价了重金属的潜在生态风险.结果表明,土壤中不同重金属的形态分布差异很大,其中,Cr、As、Ni和Co均主要以残渣态存在,分别占其总量的66.6％、61.4％、50.7％和41.8％;Cu和Se主要以可氧化态存在,分别占其总量的43.8％和67.8％;Pb主要以可还原态存在,占总量的61.1％;Cd主要以酸提取态存在,占总量的53.3％.生物有效性分析表明,Cd的可利用态K1为0.933,生物有效性是最大的,对土壤生态系统的潜在危害性较大,其次是Pb和Co;Cu和Se在土壤环境发生变化时,很容易再次释放到外界环境中;Cr、As和Ni不易被外界生物利用.潜在生态风险评价结果显示,以国家土壤环境质量标准二级标准为参比值时,Cr、Cd、Pb、As、Cu和Ni的单项潜在生态风险程度均为轻微,综合潜在生态风险处于轻微等级.     

生活垃圾焚烧飞灰重金属在浸出柱中的浸出规律

通过浸出柱实验,研究生活垃圾焚烧飞灰中重金属的动态浸出规律.结果表明,浸出液中各种重金属的质量浓度均随浸取剂与飞灰比值(L/S)增大而减小,并在L/S＞2后趋于稳定.除Pb外,浸出质量浓度均低于污水综合排放标准(GB 8978-1996)限值.对比原灰与浸出残留物重金属多级提取结果表明,飞灰的重金属在浸出柱实验中释放能力由强到弱依次为:Cd、Ni、Cu、Pb、Zn和Cr.受浸取剂pH值和固液接触方式影响,浸出柱重金属累计浸出量都小于国家标准(GB 5086.2-1997)浸出量(Cd除外),尤其Cr、Hg和Pb的浸出柱累计浸出量分别是国标浸出量的23.25%、1.29%和14.29%     

模拟酸雨对泉州市大气降尘重金属浸出特性的研究

针对福建泉州地区受污染的大气降尘样品,采用模拟酸雨浸泡的试验方法,研究不同酸度模拟酸雨(pH分别为2.5,3.5,4.5和5.6)对大气降尘样品中重金属元素浸出性质的影响。研究结果表明,Cu、Pb、Ni、Zn、Mn、Cr、V、Co、Cd均有不同程度的浸出,随着模拟酸雨pH值的升高重金属浸出率逐渐减小,pH在2.5到3.5范围内浸出率变化最大,Cd、Cu、Pb、Zn、Cr的释放量明显高于其他元素。pH是影响9种重金属元素浸出率大小的主要影响因素,降尘样品本身的酸碱度对其浸出率也有一定的影响。通过实验也让人们了解了大气降尘中重金属的潜在危害。     

两种垃圾焚烧炉灰渣的重金属成分与放射性检测

对8种重金属As、Hg、Mn、Cr、Cu、Cd、Co、Ni和Pb在两种垃圾焚烧炉灰渣中的浓度分布,浸出毒性及放射性进行检测.样品(炉渣和飞灰)分别取自北京(循环流化床焚烧炉CFBI)和深圳(炉排焚烧炉)两台不同燃烧方式的垃圾焚烧炉.研究表明,CFBI炉渣及飞灰中的重金属As、Mn、Cu、Cd、Co含量在炉渣中含量最低,中灰次之,飞灰中含量最高.重金属Hg在炉渣和飞灰中的含量相当,在中灰中的含量最低;Cr和Ni在炉渣中的含量也偏高,在中灰和飞灰中的含量相当Pb含量依中灰、炉渣和飞灰的顺序逐渐升高.浸出毒性检测结果显示,循环流化床垃圾焚烧后炉渣及飞灰中的重金属浸出毒性远低于国家标准1～2个量级,重金属总体排放量较低.炉排炉垃圾焚烧的炉渣及飞灰中的重金属含量却高很多,尤其是Cr、Pb、Cd和Cu.放射性检测结果表明,两种焚烧所产生的灰渣放射性均低于国家标准.在排放时无需作任何放射性方面的处理.最后,对焚烧灰渣的稳定化技术进行了讨论.     

某城区重金属扩散模型研究

以As、Cd、Cr、Cu、Hg、Ni、Pb、Zn为研究对象,探讨了它们在城市土壤的浓度分布特征,并进行了重金属元素的扩散模型研究。分析表明,As、Cd、Hg、Zn存在3个污染源,Cr存在一个污染源,Cu、Ni、Pb存在2个污染源.而且Cr和Ni存在相同的污染源,Hg和Pb,Cr和Cu以及Cu和Cd也存在相同的情况。     

垃圾焚烧飞灰中重金属的分布规律及化学形态分析

研究了重庆市垃圾焚烧发电厂焚烧飞灰的粒径分布,分析了焚烧飞灰中重金属的含量、浸出特性和形态分布特征,讨论了不同粒径飞灰中重金属的分布特性.结果表明,大部分飞灰粒径集中在38～250 μm,其中粒径为38～100μm飞灰占总量的49.49%.飞灰浸出液中Pb和Zn的浓度均超出了<危险废物浸出毒性鉴别标准>(GB5085.3-2007),因此该焚烧飞灰被认定为危险废物.在＜250μm粒径范围内,Cd、Cr、Cu、Mn和Pb普遍表现出向小颗粒富集的趋势;Zn的粒径分布则与上述5种元素表现出相反的趋势;Ni的分布与粒径的相关性不大,在各粒径上的分布较均匀.除Ni元素外,用BCR法分析所得的其他6种重金属形态分析结果和总量测定的结果基本吻合.飞灰中Cr、Ni、Zn和Mn主要以稳定态存在,而Cd、Pb和Cu则主要以不稳定态存在.     

浏阳河底泥中重金属释放污染水体研究

浏阳河底泥中的富集重金属的底泥会以一定形态进行二次释放。主要考察了时间、pH值、温度以及分别固定Cl-、NO-3、SO2-4的条件下常见阳离子Na+和Mg2+等因素对底泥中重金属Cd、Cr、Pb、Ni释放的影响。结果显示:①通过底泥中重金属总含量的测定,发现重金属污染程度为CdPbCuNi;同时Cd对浏阳河的潜在生态危害程度评价等级为强,其他3种重金属则属于轻微生态危害;②重金属Cd和Pb释放比较明显,Ni和Cu释放量未检测出;底泥中重金属的释放量随着时间、温度、阴离子浓度的增加而增大,除pH值在一定范围内对释放量的影响呈凹形趋势;③Cl-、NO-3、SO2-4浓度一定时,Mg2+对重金属释放量的提升作用明显大于Na+;相同浓度时,对Cd和Pb释放影响较大的是Cl-和SO2-4。     

西安市城市道路灰尘重金属污染及健康风险评价

在西安市典型旅游区、居民文教区、商业区和工业区内选择具有不同车流量的12条道路作为路面灰尘采样区域,于2013年10—11月采集路面灰尘样本72个,测试灰尘中重金属Pb、Zn、Cu、V、Ba、Cr、Cd、Ni、As的质量比,统计分析灰尘重金属污染空间分异特征,并应用美国EPA人体暴露风险评价方法评价其健康风险。结果表明:西安市道路灰尘重金属明显富集,除V外,Pb、Zn、Cu、Ba、Cr、Cd、Ni、As质量比分别是陕西土壤背景值的5.59、4.02、2.37、3.64、2.21、93.83、1.08和7.09倍,Pb、Zn、Ni质量比呈工业区最高、旅游区最小、工业区明显高于其他功能区的空间布局,Cr和Cd质量比各功能区差别不大且呈宽幅离散,居民文教区Cu、As质量比较其他功能区高,旅游区V质量比明显高于其他功能区;手-口接触摄入是路面灰尘风险暴露的主要途径,各类重金属非致癌风险从高到低为As、Cr、Pb、Ba、Cd、V、Ni、Cu、Zn,手-口接触摄入、呼吸吸入和皮肤接触3种途径对儿童和成人产生的非致癌总风险分别为2.75和0.372,灰尘暴露导致的儿童非致癌健康风险不容忽视,As、Cr、Pb、Ba是危害最大的污染物;Cr、Cd、Ni、As的致癌暴露风险从高到低为Cr、As、Cd、Ni,单一重金属的致癌风险及4种重金属总致癌风险均低于致癌风险量级水平。     

保定城市土壤重金属污染及潜在生态危害评价

为了解保定城市土壤重金属污染状况及潜在生态危害,以保定城市土壤为研究对象,采用单因子指数法、尼梅罗综合指数法、潜在生态危害指数法对保定城市土壤重金属污染特征及潜在生态危害进行评价。结果表明,保定城市土壤As、Cd、Hg、Pb、Cr、Cu、Zn、Ni的平均值分别为9. 75 mg/kg、0. 18 mg/kg、0. 21 mg/kg、38. 99 mg/kg、66. 30 mg/kg、29. 10mg/kg、122. 36 mg/kg、28. 05 mg/kg。保定城市土壤中重金属元素平均值(除As、Ni、Cr外)均高于河北省土壤背景值,其中Hg、Pb、Zn元素的平均值较大,分别是河北省土壤背景值的5. 28倍、1. 74倍、1. 75倍,表明这些元素受到人为因素及工业活动的影响。保定城市土壤重金属污染程度从大到小依次为Zn、Pb、Hg、Cd、Cu、Cr、Ni、As,其中Cd、Pb、Cu以清洁状态为主,Hg以安全状态为主,As、Cr、Ni元素处于完全清洁状态,Zn元素出现污染,面积达到研究区面积的2. 08%。整体而言,保定城市土壤环境良好,局部污染,清洁、安全、警戒土壤面积比例分别为64. 58%、33. 33%、2. 08%,主要出现在保定市北部地区,其形成可能与工业生产及人类活动有关。保定城市土壤重金属潜在危害程度由大到小依次为Hg、Cd、As、Pb、Cu、Zn、Cr、Ni。各重金属元素中,产生潜在生态危害的重金属主要是Hg,已达到很强潜在生态危害水平,其余重金属均为轻度潜在生态危害;综合潜在生态危害指数(RI)达到中等生态危害程度,达到强生态危害和很强生态危害程度的面积之和占研究区总面积的35. 41%,其形成可能与工业生产有关。     

油浸变压器排油注氮装置在500kV变电站的设计与应用

在分析500kV变电站主变压器消防系统的现状,比较3类消防系统优缺点的基础上,详细论述了主变排油注氮装置的结构组成、工作原理、参数计算、控制系统设计以及需要注意的事项等,为下一步排油注氮装置的推广应用打下基础.     

HAZOP结合What-if方法在某延迟焦化装置除焦中的应用

为克服传统危险与可操作性（HAZOP）定性分析方法在复杂操作、间歇作业等过程中使用的局限性,提出在传统HAZOP定性分析方法的基础上结合What-if（故障假设）方法,对人的不安全行为和操作规程不完备所导致的风险后果分析作出补充。详细说明其技术原理、工作流程等使用细节,系统阐述该方法与传统HAZOP定性分析方法的区别,并在某延迟焦化装置的除焦操作的风险分析中应用。经分析,识别出在“给水-泡焦”节点,有“操作规程错误”场景2项,“操作规程不具体”场景1项,不存在“操作人员未按操作规程执行”场景。研究结果表明:本文方法有效且具有较好效果,可以广泛应用于操作规程/作业指导书审查、作业过程隐患排查等方面,帮助企业开展操作层面的风险识别与管理,提升企业的生产安全水平。     

潞安矿区煤层渗透率的各向异性特征实验研究

为了研究原位煤体渗透性的各向异性特征,以山西潞安常村矿3号煤层圆柱试样为对象,利用TCQT-Ⅲ型低渗煤层气相驱替增产试验装置,对煤样进行加载,并以氮气注入压力2.0 MPa的条件下,分析垂直层理和平行层理2个方向的煤体变形和渗透率变化特征。实验结果表明:煤样在加载过程中,平行和垂直层理煤样渗透率均随着有效应力的增大而减小,平行层理方向的渗透率始终大于垂直层理方向,应力加载初期渗透率急剧下降,最后逐渐趋于平缓;径向应变的增加量与渗透率呈正相关性,且平行层理相关性大于垂直层理;沿平行层理方向的裂隙度大于沿垂直层理方向,沿垂直层理方向的应变量大于沿平行层理方向;应变增加量均随有效应力的增加而逐渐减小。研究结果可为煤层井网布置及优化提供参考。     

Nighttime pedestrian fatalities: A comprehensive examination of infrastructure,user, vehicle,and situational factors

Introduction: Pedestrian fatalities in the United States increased 45.5% between 2009 and 2017. More than 85% of those additional pedestrian fatalities occurred at night. Method: We examine Fatality Analysis Reporting System (FARS) data for fatal pedestrian crashes that occurred in the dark between 2002 and 2017. Within-variable and before/after examinations of crashes in terms of infrastructure, user, vehicle, and situational characteristics are performed with one-way analysis of variance (ANOVA) and two-sample t-tests. We model changes in crash characteristic proportions between 2002–2009 and 2010–2017 using linear regressions and test for autocorrelation with Breusch-Godfrey tests. Results: The increase in fatal nighttime pedestrian crashes is most strongly correlated with infrastructure factors: non-intersection unmarked locations (saw 80.8% of additional fatalities); 40–45 mph roads (54.6%); five-lane roads (40.7%); urban (99.7%); and arterials (81.1%). In addition, SUVs were involved in 39.7% of additional fatalities, overrepresenting their share of the fleet. Increased pedestrian alcohol and drug involvement warrant further investigation. The age of pedestrians killed increased more (18.1%) than the national average (3.2%). Conclusions: By identifying factors related to the increase in nighttime pedestrian fatalities, this work constitutes a vital first step in making our streets safer for pedestrians. Practical Applications: More research is needed to understand the efficacy of different solutions, but this paper provides guidance for such future research. Engineering solutions such as road diets or traffic calming may be used to improve identified infrastructure issues by reducing vehicle speeds and road widths. Rethinking vehicle design, especially high front profiles, may improve vehicle issues. However, the problems giving rise to these pedestrian fatalities are likely a result of not only engineering issues but also interrelated social and political factors. Solutions may be correspondingly comprehensive, employing non-linear, systems-based approaches such as Safe Systems.     

Footedness and Mounting—Short Review and Two Case Studies

Footedness is a personal quality like handedness. Footedness may be associated with moving ability during mounting, dismounting, and jumping movements. Occupational accidents have occurred during movement at different working levels, during the use of access and exit systems, and during the mounting of vehicles. Aging can also affect accident risk and body laterality. For example, falling accidents on stairs are common among the elderly. One reason for accidents may be that the structure of the access system or stair system is unsuitable for individual moving patterns depending partly on body laterality. Footedness and the way the feet are used may be contradictory to the demands of the moving situation, especially during uncommon or rapid situations. This contradiction may trigger disturbance during moving. The aims of this pilot study were (a) to review the literature briefly and (b) to describe the use of the dominant and nondominant foot by farmers and the elderly when mounting a tractor and stairs, respectively. The study also gives ideas for future studies based on both (a) and (b).     

AHP与GA-SVM耦合模型在滑坡预警中的应用*

为了减少滑坡造成的损失,提高滑坡预测的准确性,通过搭建灾害模拟平台获得滑坡的实验数据,在获得多组模拟实验数据后,分析各变量的特性。首先,通过层次分析(Analytic Hierarchy Process,AHP)算法,对滑坡进行危险度划分;然后,通过支持向量机(Support Vector Machine,SVM)建立模型,遗传算法(Genetic Algorithm,GA)再优化SVM参数,提出1种层次分析法与GA-SVM相耦合的模型。研究结果表明:AHP方法划分后的数据,通过GA与SVM结合建立的模型精度较好,实验预测结果与实际结果较为吻合,与单一SVM相比,精度更高,结果更好,更加适用于多变量的复杂非线性滑坡预警。     

Debunking the false dichotomy of leadership idealism and pragmatism: Critical evaluation and support of newer genre leadership theories

Leadership theories have shifted over the last few decades from a focus on managerial functions and economic leader–follower exchanges toward greater focus on the interpersonal dynamics occurring within the leadership process. Theories such as transformational, ethical, authentic, and other “newer genre” theories were created to address neglected topics such as leader vision and inspirational messages, transparency, emotional effects, morality, individualized attention, and intellectual stimulation. Critiques of these theories, however, have been raised. In this paper, we address five of those critiques and argue for the validity and practical effectiveness of the new genre theories. Further, we describe how newer genre leadership research should be viewed as a performative epistemology, entailing a process of co‐creation involving scholars and practitioners. Finally, from this view, we provide general ideas for leader development. Copyright © 2014 John Wiley & Sons, Ltd.     

Occupational Safety and Health in Finland

In Finland, occupational safety is the responsibility of the employer, while the occupational safety and health laws are enforced by the Labour Inspection Service, an organization of the state. The Labour Inspection is divided in 11 administrative districts, and it employs 360 professionals. They are mandated to carry out site visits without prearranged appointments to inspect safe work situations, working hours, construction safety, or any aspect of accident risks. The inspectors are also mandated to verify the existence of sufficient occupational health services as prescribed by the Occupational Health Services Act for all employees. The occupational health services are typically provided by enterprise-owned medical departments, by mutually owned health care centers, by private practitioners, or by municipal health care centers. The latter are required by law to provide all services as prescribed by the legislation to anyone who comes to the facility. This situation is prevalent in the countryside, where there are very few private caregiving centers. Declaring occupational accidents and disease cases is mandatory, and the Inspection districts examine all accidents to establish causes and consequences, and to initiate prosecution in case of criminal negligence. Labour Inspection Districts are also notified of the new occupational disease cases as they are declared to insurance companies. Insurance for occupational disease, accidents, and death is an obligation of the employer, although they can choose the insurance company. The medical confidentiality between the workers and their occupational health care providers is very strict. Official statistics are maintained by the state Statistics Finland organization, and they may be used, for example, for research purposes by scientific institutes like the Finnish Institute of Occupational Health. Construction industry accounts for 25% of all fatal accidents (120 cases per 1 million working hours), followed by mechanical, wood, metal, machinery, and pulp and paper industry (10% each of fatal accidents) with rates ranging from 100–160 cases per 1 million working hours. There are some 5,000 occupational disease cases per year (rate 22/10,000 employed). The major disease categories include repetitive strain injuries (1,300 cases), respiratory allergies (600 cases), occupational skin diseases (1,000 cases), and 900 cases of noise-caused hearing loss. In 1998, 589 cases of asbestos-related diseases were reported.     

森林地表火蔓延模拟方法及其计算机实现

进行了森林火蔓延的研究,对传统的经验公式和模型进行改进,明显发现改进的模型有更好的结果,用计算机巧妙准确地实现了模拟模型,在风力不是特别大,地形变化不是特别剧烈时,该模型有较高精度;并结合火蔓延的主要因素（气象因子、气候、地形等）,进行系统分析,写出算地,编制实现地表火蔓延的预测预报计算机系统软件。这对于有效的组织扑救、减少火灾损失、计算森林火灾的损失评估有重要意义。     

公路隧道火灾逃生疏散研究

以苍岭隧道为背景,首先采用经验计算理论和计算软件building EXODUS相结合的方式,从被困人员的安全疏散时间、高温烟气的影响、隧道横通道的利用率以及人员的疏散行为特性进行了研究。结果表明:中小规模火灾情况下的安全疏散时间控制在8 min之内,高温烟气影响不大,但横通道的利用率不平均,且人员疏散路线相对集中。然后对存在的逃生疏散问题提出针对性建议以及其他相关建议,旨在为更大程度降低事故的严重性和经济财产损失。