Petrographic and spectroscopic characterization of phosphate-stabilized mine tailings from Leadville,Colorado

The use of soluble PO4(3-) and lime as a heavy metal chemical stabilization agent was evaluated for mine tailings from Leadville, Colorado. The tailings are from piles associated with the Wolftone and Maid of Erin mines; ore material that was originally mined around 1900, reprocessed in the 1940s, and now requires stabilization. The dominant minerals in the tailings are galena (PbS), cerrusite (PbCO3), pyromorphite (Pb5(PO4)3Cl), plumbojarosite (Pb0.5Fe3(SO4)2(OH)6), and chalcophanites ((Pb,Fe,Zn,Mn)Mn2O5 x 2H2O). The tailings were treated with soluble PO4(3-) and lime to convert soluble heavy metals (principally Pb, Zn, Cu, Cd) into insoluble metal phosphate precipitates. The treatment process caused bulk mineralogical transformations as well as the formation of a reaction rind around the particles dominated by Ca and P. Within the mineral grains, Fe-Pb phosphosulfates, Fe-Pb sulfates (plumbojarosite), and galena convert to Fe-Ca-Pb hydroxides. The Mn-Pb hydroxides and Mn-(+/-Fe)-Pb hydroxides (chalcophanites) undergo chemical alteration throughout the grains during treatment. Bulk and surface spectroscopies showed that the insoluble reaction products in the rind are tertiary metal phosphate (e.g. (Cu,Ca2)(PO4)2) and apatite (e.g. Pb5(PO4)3Cl) family minerals. pH-dependent leaching (pH 4,6,8) showed that the treatment was able to reduce equilibrium concentrations by factors of 3 to 150 for many metals; particularly Pb2+, Zn2+, Cd2+, and Cu2+. Geochemical thermodynamic equilibrium modeling showed that apatite family and tertiary metal phosphate phases act as controlling solids for the equilibrium concentrations of Ca2+, PO4(3-) Pb2+, Zn2+, Cd2+, and Cu2+ in the leachates during pH-dependent leaching. Both end members and ideal solid solutions were seen to be controlling solids.     

Hydrothermal solidification behavior of municipal solid waste incineration bottom ash without any additives

Municipal solid waste incineration (MSWI) bottom ash could be solidified with and without slaked lime (calcium hydroxide) addition by a hydrothermal method under steam pressure of 1.56 MPa at 200 °C for up to 72 h. Experimental results showed that CSH gel or tobermorite exerted a main influence on strength development, and without any additives CSH gel was easy to form, while slaked lime addition favored to form tobermorite. Tobermorite seemed to exert a larger effect on the strength development than CSH gel. Leaching results showed that the concentrations of heavy metals dissolved from the solidified specimens were effectively reduced after hydrothermal processing. The immobilization was mainly due to the tobermorite or CSH gel formation, and Pb²⁺ and Zn²⁺ seemed to be fixed more readily than Cr⁶⁺, which might be the reason that the structural Ca²⁺ within tobermorite or CSH gel was exchanged by Pb²⁺ and Zn²⁺ more easily than Cr⁶⁺. In addition, there existed a close relationship between leaching concentration and strength enhancement, and a higher strength seemed to exert a larger effect on immobilization of heavy metals.     

Synthesis,Characterization and Environmental Applications of a New Bio-Composite Gelatin-Zr(IV) Phosphate

Gelatin-Zr(IV) phosphate composite (GT/ZPC) was synthesized by sol–gel method. Different techniques viz. Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray powdered diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used for the characterisation of GT/ZPC composite ion exchanger. The ion exchange capacity (IEC) of GT/ZPC was observed to be better (1.04 meq g^?1) than its inorganic counterpart (0.64 meq g^?1). The pH studies revealed the monofunctional nature of GT/ZPC with one inflection point. The distribution studies showed that the GT/ZPC was highly selective for Cd²⁺ as compare to other metal ions. The environmental applicability of ion exchanger has been analysed for binary separations of metal ions using column method. Cd²⁺ was effectively removed from synthetic mixture of metal ions (Zn²⁺, Pb²⁺, Ni²⁺, Co²⁺ and Cu²⁺).     

Itaconic Acid Grafted Starch Hydrogels as Metal Remover: Capacity,Selectivity and Adsorption Kinetics

Hydrogels were synthesized by free radical graft copolymerization of itaconic acid (IA) onto corn starch (S-g-IA). For this purpose, potassium permanganate (KMnO₄)-sodium bisulfite (NaHSO₃) was used as redox initiation system. The formation of grafted starches was confirmed by Fourier transform infrared spectroscopy, wide angle X-ray scattering, thermogravimetric analysis and scanning electron microscopy. The effect of monomer concentration, neutralization, addition of crosslinking agent, N,N-bismetilenacrilamide (MBAm), and initiator concentration on grafting efficiency and adsorption capacity of the starch hydrogels was investigated. It was demonstrated that the introduction of carboxyl and carbonyl groups promoted starch hydration and swelling. Grafting degree increased with the decrease of monomer concentration, increase of initiator concentration, grade of neutralization and the addition of MBAm without neutralization. Remarkably the resulting materials exhibited water absorption capacities between 258 and 1878% and the ability to adsorb metal ions. It was experimentally confirmed the metal uptake, obtaining the higher adsorption capacity (q _e  = 35 mg/g) for the product prepared with the pre-oxidation and lower initiator concentration. The removal capacity order was Pb²⁺>Ni²⁺>Zn²⁺>Cd²⁺. Moreover, the experimental kinetic and the equilibrium adsorption data for Ni²⁺ and Pb²⁺ were best fitted to the pseudo-second order and Freundlich isotherm models, respectively. This work describes for the first time the preparation of metal removal hydrogels based on starch and itaconic acid using the pair redox system KMnO₄/NaHSO₃, which avoids the starch hydrolysis and allows itaconic acid grafting incorporation without the requirement of more reactive comonomers.     

Poultry litter-based activated carbon for removing heavy metal ions in water

Utilization of poultry litter as a precursor material to manufacture activated carbon for treating heavy metal-contaminated water is a value-added strategy for recycling the organic waste. Batch adsorption experiments were conducted to investigate kinetics, isotherms, and capacity of poultry litter-based activated carbon for removing heavy metal ions in water. It was revealed that poultry litter-based activated carbon possessed significantly higher adsorption affinity and capacity for heavy metals than commercial activated carbons derived from bituminous coal and coconut shell. Adsorption of metal ions onto poultry litter-based carbon was rapid and followed Sigmoidal Chapman patterns as a function of contact time. Adsorption isotherms could be described by different models such as Langmuir and Freundlich equations, depending on the metal species and the coexistence of other metal ions. Potentially 404 mmol of Cu²⁺, 945 mmol of Pb²⁺, 236 mmol of Zn²⁺, and 250–300 mmol of Cd²⁺ would be adsorbed per kg of poultry litter-derived activated carbon. Releases of nutrients and metal ions from litter-derived carbon did not pose secondary water contamination risks. The study suggests that poultry litter can be utilized as a precursor material for economically manufacturing granular activated carbon that is to be used in wastewater treatment for removing heavy metals.     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

Synthesis of mesoporous silica materials from municipal solid waste incinerator bottom ash

Incinerator bottom ash contains a large amount of silica and can hence be used as a silica source for the synthesis of mesoporous silica materials. In this study, the conditions for alkaline fusion to extract silica from incinerator bottom ash were investigated, and the resulting supernatant solution was used as the silica source for synthesizing mesoporous silica materials. The physical and chemical characteristics of the mesoporous silica materials were analyzed using BET, XRD, FTIR, SEM, and solid-state NMR. The results indicated that the BET surface area and pore size distribution of the synthesized silica materials were 992 m²/g and 2–3.8 nm, respectively. The XRD patterns showed that the synthesized materials exhibited a hexagonal pore structure with a smaller order. The NMR spectra of the synthesized materials exhibited three peaks, corresponding to Q² [Si(OSi)₂(OH)₂], Q³ [Si(OSi)₃(OH)], and Q⁴ [Si(OSi)₄]. The FTIR spectra confirmed the existence of a surface hydroxyl group and the occurrence of symmetric Si–O stretching. Thus, mesoporous silica was successfully synthesized from incinerator bottom ash. Finally, the effectiveness of the synthesized silica in removing heavy metals (Pb²⁺, Cu²⁺, Cd²⁺, and Cr²⁺) from aqueous solutions was also determined. The results showed that the silica materials synthesized from incinerator bottom ash have potential for use as an adsorbent for the removal of heavy metals from aqueous solutions.     

Adsorption characteristics of Cu2+ and Zn2+ from aqueous solution using carbonized food waste

The aim of the present study was to analytically provide adsorption characteristics of Cu²⁺ and Zn²⁺ using carbonized food waste (CFW); more specifically, batch tests were conducted using various concentrations of metal ions, contact times, and initial pH levels in an attempt to understand the adsorption removal of heavy metal ions in aqueous solution at concentrations ranging between 50 and 800 mg/l. The results confirmed that the adsorption equilibrium was established within a maximum of 80 min, and the maximum concentrations for adsorption of Cu²⁺ and Zn²⁺ were 28.3 and 23.5 mg/g, respectively. These adsorption levels indicate that CFW has better performance than many other adsorbents. In experiments using different pH conditions, the applicability to acid wastewater was found to be high, and an excellent adsorption removal ratio of 75%–90% was observed under acid conditions at pH 2–4. Furthermore, as the adsorption time increased, the calcium component in the CFW began to leach into the aqueous solution and raise the pH, accordingly causing the removal of heavy metal ions partially as a result of precipitation. When our results were analyzed using the Langmuir model and the Freundlich model for isothermal adsorptivity, the activity of CFW in this study was shown to be more consistent with the former; the adsorption speed of Cu²⁺ and Zn²⁺ according to a pseudosecond-order reaction model was found to be very fast for an initial concentration of not more than 100 mg/l. In a test in which an attempt was made to compare adsorption capacity values obtained from the experiments in this study with the aforementioned three models, the pseudosecond-order reaction model was found to provide results closest to the actual values.     

A case study of microwave processing of metal hydroxide sediment sludge from printed circuit board manufacturing wash water

The large quantity of wash water used in the electroplating and etching process in the manufacturing of printed circuit boards (PCBs) contains a high level of heavy metal ions (Cu⁺⁺, Zn⁺⁺, Ni⁺⁺, Cr⁺⁺⁺, Pb⁺⁺). These potentially toxic ions are removed from the wash water effluent through a polyelectrolyte flocculation and hydroxide precipitation process during which a hydroxide sediment sludge rich in metal ions and polymers is generated. This sediment sludge possesses some unique characteristics and properties in terms of composition, fine particle size distribution, high specific surface area, and a tendency to agglomerate after drying. Direct disposal of this classified “special waste” (Department of Environment of Northern Ireland, The Special Waste Regulations, Northern Ireland, 1998) at landfill sites may cause serious soil and underground water pollution through a gradual ionic leaching process. This paper describes an experimental investigation, exploratory in nature, which employs microwave radiation for detoxification of the sediment sludge through microwave heating, drying and metal ion immobilization within the sediment solids. The effectiveness of microwave assisted binding and immobilization of the metal ions within the sediment solids was studied in conjunction with an evaluation of microwave energy efficiency in comparison to the more conventional convective heating and drying processes. Given a sufficient amount of microwave radiation, leaching of Cu²⁺ and Pb²⁺ was reduced by 2700% and 1080%, respectively, over a period of 12 weeks, and further leaching was not detectable within six months at simulated local landfill aqueous conditions. This paper also attempts, through experimental observation, to add to the very limited understanding of the complex interactions and binding of free metal ions with the polymeric materials and metal hydroxides under the influence of an electromagnetic field. The high specific surface of the sediment solids and their adsorption properties were further explored and characterized in a study of adsorption of reactive dyes by the microwave processed solids.     

Polymer Supported Calix[4]Arene Derivatives for the Extraction of Metals and Dichromate Anions

Three newly synthesized polymer supported calix[4]arene ionophores (7–9) were synthesized, and their ion binding properties toward selected alkali (Li⁺, Na⁺, K⁺, Cs⁺) and transition metal (Hg²⁺, Ni²⁺, Cu²⁺, Co²⁺, Cd²⁺, and Pb²⁺) cations were investigated. It has been observed that these ionophores are not selective toward a particular metal cation but show better ion binding property as compared to monomeric calixarene derivatives (2 and 6). Ionophore 6 and its supported polymer were also employed in dichromate anion extraction experiments. The polymeric ionophore (9) was found an effective extractant for dichromate anion even at pH 7.     

Design parameters for fixed bed reactors of activated carbon developed from fertilizer waste for the removal of some heavy metal ions

Activated carbon, developed from fertilizer waste, has been used for the removal of Hg²⁺, Cr⁶⁺, Pb²⁺, and Cu²⁺. Mass transfer kinetic approach has been successfully applied for the determination of various parameters necessary for designing a fixed-bed absorber. Parameters selected are the length of the (PAZ) primary adsorption zone (δ), total time involved for the establishment of primary adsorption zone (t_x), mass rate of flow to the absorber (F_m), time for primary adsorption zone to move down its length (t_δ), amount of adsorbate adsorbed in PAZ from breakpoint to exhaustion (M_s), fractional capacity (f), time of initial formation of PAZ (t_f) and per cent saturation of column at break point. Chemical regeneration has been achieved with 1 M HNO₃.     

Ammonium removal from landfill leachate by chemical precipitation

The landfill leachate in Hong Kong usually contains quite high NH₄⁺–N concentration, which is well known to inhibit nitrification in biological treatment processes. A common pre-treatment for reducing high strength of ammonium (NH₄⁺–N) is by an air-stripping process. However, there are some operational problems such as carbonate scaling in the process of stripping. For this reason, some technical alternatives for NH₄⁺–N removal from leachate need to be studied. In this study, a bench-scale experiment was initiated to investigate the feasibility of selectively precipitating NH₄⁺–N in the leachate collected from a local landfill in Hong Kong as magnesium ammonium phosphate (MAP). In the experiment, three combinations of chemicals, MgCl₂·6H₂O+Na₂HPO₄·12H₂O, MgO+85% H₃PO₄, and Ca(H₂PO₄)₂·H₂O+MgSO₄·7H₂O, were used with the different stoichiometric ratios to generate the MAP precipitate effectively. The results indicated that NH₄⁺–N contained in the leachate could be quickly reduced from 5618 to 112 mg/l within 15 min, when MgCl₂·6H₂O and Na₂HPO₄·12H₂O were applied with a Mg²⁺:NH₄⁺:PO₄³⁻ mol ratio of 1:1:1. The pH range of the minimum MAP solubility was discovered to be between 8.5 and 9.0. Attention should be given to the high salinity formed in the treated leachate by using MgCl₂·6H₂O and Na₂HPO₄·12H₂O, which may affect microbial activity in the following biological treatment processes. The other two combinations of chemicals [MgO+85% H₃PO₄ and Ca(H₂PO₄)2·H₂O+MgSO₄·7H₂O] could minimise salinity after precipitation, but they were less efficient for NH₄⁺–N removal, compared with MgCl₂·6H₂O and Na₂HPO₄·12H₂O. COD had no significant reduction during this precipitation. It was found that the sludge of MAP generated was easily settled within 10 min to reach its solids content up to 27%. The other characteristics including capillary suction time (CST) and dry density (DD) of the MAP sludge were also tested. The experimental results indicate that the settled sludge is quite solid and can be directly dumped at a landfill site even without any further dewatering treatment.     

Adsorption of Pb2+ and Cd2+ on the l-cysteine-functionalized graphene oxide/chitosan/polyvinyl alcohol hydrogel: Kinetic,isotherm, and thermodynamic study

In this study, polyvinyl alcohol-chitosan-cysteine-functionalized graphene oxide (PCCFG) hydrogel was synthesized from l -cysteine-functionalized graphene oxide (CFG), chitosan (CS), and polyvinyl alcohol (PVA). The hydrogel was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy and employed for removing lead ion (Pb²⁺) and cadmium ion (Cd²⁺) from aqueous solution. The effects of initial metal ion concentration, hydrogel dose, pH, time, and temperature were studied. The experimental data were well described by a pseudo-second-order kinetic model and Langmuir isotherm with maximum adsorption capacities of 250 and 192 mg g⁻¹ at 25°C for Pb²⁺ and Cd²⁺, respectively. The adsorption capacity of the PCCFG hydrogel increased with an increase in temperature. The value of ∆G° was negative, which shows the spontaneity of the reaction (electron exchange or ion exchange) between the metal ion and electron-rich atoms (–N, –S, –O). The positive ∆H° shows that the adsorption reaction consumes energy and the positive ∆S° shows the strong affinity of PCCFG toward the Pb²⁺ and Cd²⁺ ions. Pb²⁺ had better affinity and less spontaneity than Cd²⁺. The results show that the coexistence of Pb²⁺, Cd²⁺, and Cu²⁺ in the solution inhibits the adsorption capacity of PCCFG.     

Trends in Water Chemistry in a Maple Forest on a Steep Slope

Year-to-year variation in SO₄ ^2-,NO₃ ^-, Ca²⁺, K⁺, and Mg²⁺concentrations in forest floor and mineral soil percolatefrom a forested, podzolic soil at the Turkey Lakes Watershedon the Precambrian Shield was assessed for monotonic trendsbetween 1986 and 1995. Our objective was to examine howrapidly ion concentrations in soil percolate equilibratedafter stabilization of SO₄ ^2- concentrations inprecipitation. Significant negative trends were detected inmonthly Ca²⁺, and Mg²⁺ concentrations in forestfloor and SO₄ ^2-, Ca²⁺, and Mg²⁺ inmineral soil percolate during the 10-year-period. Thedecline in Ca²⁺ and Mg²⁺ was greater than annualdecreases in SO₄ ^2- and NO₃ ^- in forestfloor percolate and proportional to the reduction inSO₄ ^2- in mineral soil percolate. Response ofmineral soil percolate to a 15 mol_c L^-1SO₄ ^2- decrease in wet-only precipitation between1985 and 1986 was a gradual decline in SO₄ ^2-concentration through 1995. The five-year meanSO₄ ^2- concentration in bulk precipitation, forestfloor percolate, and mineral soil percolate decreased 8, 9and 18 mol_c L^-1 from 1986–90 to 1991–95.Microbial (mineralization of organic S) and sorption(release from and/or retention in the pool of insolubleSO₄ ^2-) processes in the soil were logicalexplanations for the observed changes in SO₄ ^2- inmineral soil percolate.     

Accumulation of Heavy Metals by in vitro cultures of plants

The aim of the project is to study heavy metals accumulation by the selected plants in both laboratory and field conditions. Within the experiments the aspen (Populus tremula × tremuloides), sunflower (Helianthus annuus) and corn (Zea mays) plants were studied. The reasons for this selection were: a fast growth of these plants, an accumulation capacity and an ability to survive in different types of soils. The study was carried out on the aspen plantlets grown in vitro. The plants were exposed to the aqueous solutions having concentrations 0.1 mM, 0.5 mM of Pb²⁺ or Ni²⁺, respectively. The accumulation capacityfor aspen, was about 70% of Pb²⁺ originally present in the solution. The starting concentration of Pb²⁺ (0.5 mM) exhibited no negative impact on the growth. Besides in vitro expositions, a pilot-scale phytoremediation experiment was carried out at the polluted industrial area (Zn – 75000 mg/kg), (Pb – 16000 mg/kg), (Cr – 590 mg/kg), (Cd – 90 mg/kg) and (Cu – 1700 mg/kg).     

Effects of Acid Rain on Competitive Releases of Cd, Cu, and Zn from Two Natural Soils and Two Contaminated Soils in Hunan, China

Leaching experiments of rebuilt soil columns with two simulated acid rain solutions (pH 4.6–3.8) were conducted for two natural soils and two artificial contaminated soils from Hunan, south-central China, to study effects of acid rain on competitive releases of soil Cd, Cu, and Zn. Distilled water was used in comparison. The results showed that the total releases were Zn>Cu>Cd for the natural soils and Cd>Zn≫Cu for the contaminated soils, which reflected sensitivity of these metals to acid rain. Leached with different acid rain, about 26–76% of external Cd and 11–68% external Zn were released, but more than 99% of external Cu was adsorbed by the soils, and therefore Cu had a different sorption and desorption pattern from Cd and Zn. Metal releases were obviously correlated with releases of TOC in the leachates, which could be described as an exponential equation. Compared with the natural soils, acid rain not only led to changes in total metal contents, but also in metal fraction distributions in the contaminated soils. More acidified soils had a lower sorption capacity to metals, mostly related to soil properties such as pH, organic matter, soil particles, adsorbed SO₄ ²⁻, exchangeable Al³⁺ and H⁺, and contents of Fe₂O₃ and Al₂O₃.     

Concentrations of heavy metals in fly ash from a coal-fired power plant with respect to the new Finnish limit values

In Finland, the new limit values for heavy metals in fertilizers used in agriculture and in forestry came into force in March 2007, and for materials used as earth construction agents, in June 2006. From the utilization point of view, it was notable that the total heavy metal concentrations (Cd, Cu, Pb, Cr, Mo, Zn, As, Ni, Ba, and Hg) in fly ash from a coal-fired power plant were lower than those limit values. The concentrations of the easily soluble elements Ca, Mg, Na, P, and Zn in the fly ash were between 3.5 and 35 times higher than those found in the coarse mineral soils of Finland. Fly ash is a potential agent for soil remediation and for improving soil fertility. If inorganic materials and by-products are utilized in earthworks, the content of harmful compounds must be low and the harmful components must be tightly bound to the matrix. Therefore, a five-stage sequential extraction procedure was used to evaluate the extractability of different elements in fly ash into the following fractions: (1) the water-soluble fraction, (2) the exchangeable fraction (CH₃COOH), (3) the easily reduced fraction (NH₂OH-HCl), (4) the oxidizable fraction (H₂O₂ + CH₃COONH₄), and (5) the residual fraction (HF + HNO₃ + HCl).     

Study of Bulk and Sub-Event Wet Deposition in Gebze,Turkey

This study presents the chemical composition of bulk deposition during the period of February 1996–May 1997 and the chemical composition of sub-event wet deposition on 13 August 1997 in Gebze. Samples were analyzed for SO₄ ^2-, NO₃ ^-, Cl^-,Ca²⁺, Mg²⁺, K⁺, Na⁺, and NH₄ ⁺ in addition to pH. The source of some ionic components in the bulk deposition such as K⁺ and Ca²⁺ were found to be the terrestrial regions, as expected. The (non-sea Cl^-)/Cl^- ratio of 0.05 suggests that the very large portion of Cl^- in the bulkdeposition was of marine origin. The ratio of (non-sea SO₄ ^2-)/SO₄ ^2- varied between 0.86 and 0.99,indicating that the main source of sulfate was not the sea. It is found that the sulfate and calcium concentrations were highest in summer and lowest in fall. The analysis of bulk deposition also indicated that nearly 24% of the events were acidic (pH < 5.6). During sub-event wet deposition collectedon the same site pH decreased continually, and during the passageof cold front concentrations of Cl^-, SO₄ ^2- and NO₃ ^- increased.     

Development of Stream Water Chemistry during Spring Melt in a Northern Hardwood Forest

The role of snowmelt and subsurface hydrology in determiningthe chemistry of a small headwater stream in the TurkeyLakes Watershed (TLW) was evaluated for the spring meltperiods 1992 to 1996. Spring runoff is the dominanthydrological event at the TLW each year. Processesoccurring within the snowpack during snowmelt wereprincipally responsible for the above-ground changes inchemical fluxes relative to bulk deposition (the effect ofwinter throughfall was minimal). Large changes in chemicalfluxes occurred below ground. Organic matter decomposition,weathering, nitrification, and element cycling are some ofthe more important below-ground processes that operateduring the snow accumulation and ablation season and controlthe composition of the water ultimately appearing in thestream. Maximum stream discharge was accompanied byelevated concentrations of H⁺, NO₃ ^-, K⁺,NH₄ ⁺, DOC, Al and Mn, but reduced levels ofCa²⁺, Mg²⁺, SO₄ ^2- and SiO₂. Theconcentration-discharge relationships were consistent withwater movement through and above the forest floor duringpeak discharge, a flowpath facilitated by rapid infiltrationof meltwater and the existence of a relatively impermeablelayer in the mineral soil creating a perched water table. Averaged over the five periods of snow accumulation andablation, it was estimated that pre-melt stream flow, andwater routed through the forest floor and through the uppermineral soil contributed 9, 28 and 63%, respectively, ofthe discharge measured at the outlet of the catchment. Theforest floor contribution would be greater at peak dischargeand at higher elevations. An end-member mixing modelestimated concentrations of SO₄ ^2-, NO₃ ^-,Cl^-, Ca²⁺, Mg²⁺, Na⁺ and Al that werecomparable to average values measured in the stream. Othervariables (NH₄ ⁺, H⁺, K⁺ and DOC) wereover-estimated implying retention mechanisms operatingoutside the model assumptions.     

Insight into the Adsorption Properties of Chitosan/Zeolite-A Hybrid Structure for Effective Decontamination of Toxic Cd (II) and As (V) Ions from the Aqueous Environments

Chitosan/zeolite-A hybrid structure (CS/Z.A) was synthesized and characterized as a multifunctional and environmental adsorbent for the Cd (II) and As (V) ions. The adsorption capacities of CS/ZA for Cd (II) and AS (V) are 170 mg/g and 125 mg/g, respectively which are higher values than several adsorbents in literature. The kinetic study demonstrates Pseudo-First-order behavior for the Cd (II) adsorption process and Pseudo-second order for the As (V) uptake reactions. The Cd (II) and As (V) uptake reactions follow the Freundlich equilibrium behavior with heterogeneous and multilayer adsorption properties. The kinetic and equilibrium studies in addition to the Gaussian energy {6.35 kJ/mol [Cd (II)] and 9.44 kJ/mol [As (V)]} demonstrate physical properties for the Cd (II) adsorption mechanism and more chemical behavior for the As (V) adsorption mechanism. The thermodynamic study declares exothermic, spontaneous, and favorable adsorption reactions for Cd (II) and As (V) by CS/Z.A composite. The CS/Z.A is of significant capacity for Cd (II) and As (V) ions in the existence of other competitive dissolved anions (PO₄^3?, NO₃^?, and SO₄^2?) and other metals [Zn (II), Co (II), and Pb (II)]. Finally, the CS/Z.A composite is a recyclable product and can be applied in effective Cd (II) and As (V) decontamination processes for five runs.