Co-surfactant of ethoxylated sorbitan ester and sorbitan monooleate for enhanced flushing of tetrachloroethylene

This work evaluated the flushing efficiency of tetrachloroethylene (PCE) using the co-surfactant of non-ionic ethoxylated sorbitan ester (Tween) and oilphilic sorbitan monooleate (Span 80), which formed more hydrophobic micelles than Tween alone. The flushing efficiency was evaluated with laboratory columns filled with silica and aquifer sand. Results from column flushing were also compared to those of batch solubility experiments to study the removal mechanism by the co-surfactant solution. Compared to Tween 80 alone, the molar solubilization ratio and the affinity between the micelles and PCE increased 84% and 90%, respectively, by the co-surfactant solution of Tween 80 and Span 80 mixed at a 4:1 ratio. Flushing with 1% Tween 80 solution yielded a steady PCE recovery of 7% for both silica and aquifer sand in each pore volume (PV). Flushing with co-surfactant of 1% Tween 80 + Span 80 (4:1) further increased PCE recovery to 10% for silica sand and 13% for aquifer sand per PV. A comparison of results from column flushing and batch solubility tests indicated that the primary flushing mechanism of PCE using the co-surfactant solution of Tween 80 + Span 80 (4:1) was micellar solubilization.     

Effects of ethanol addition on micellar solubilization and plume migration during surfactant enhanced recovery of tetrachloroethene

Alcohol addition has been suggested for use in combination with surfactant flushing to enhance solubilization kinetics and permit density control of dense non-aqueous phase liquid (DNAPL)-laden surfactant plumes. This study examined the effects of adding ethanol (EtOH) to a 4% Tween 80 (polyoxyethylene (20) sorbitan monooleate) solution used to flush tetrachloroethene (PCE)-contaminated porous media. The influence of EtOH concentration, subsurface layering and scale on flushing solution delivery and PCE recovery was investigated through a combination of experimental and mathematical modeling studies. Results of batch experiments demonstrated that the addition of 2.5%, 5% and 10% (wt.) EtOH incrementally increased the PCE solubilization capacity and viscosity of the surfactant solution, while reducing solution density from 1.002 to 0.986 g/cm3. Effluent concentration data obtained from one-dimensional (1-D) column experiments were used to characterize rate-limited micellar solubilization of residual PCE, which was strongly dependent upon flow velocity and weakly dependent upon EtOH concentration. Two-dimensional (2-D) box studies illustrated that minor differences (0.008 g/cm3) between flushing and resident solution density can strongly influence surfactant front propagation. A two-dimensional multiphase simulator, MISER, was used to model the influence of EtOH composition on the aqueous flow field and PCE mass recovery. The ability of the numerical simulator to predict effluent concentrations and front propagation was demonstrated for both 1-D columns and 2-D boxes flushed with EtOH-amended Tween 80 solutions. Results of this study quantify the potential influence of alcohol addition on surfactant solution properties and solubilization capacity, and demonstrate the importance of considering small density variations in remedial design.     

Surfactant enhanced recovery of tetrachloroethylene from a porous medium containing low permeability lenses. 1. Experimental studies

A matrix of batch, column and two-dimensional (2-D) box experiments was conducted to investigate the coupled effects of rate-limited solubilization and layering on the entrapment and subsequent recovery of a representative dense NAPL, tetrachloroethylene (PCE), during surfactant flushing. Batch experiments were performed to determine the equilibrium solubilization capacity of the surfactant, polyoxyethylene (20) sorbitan monooleate (Tween 80), and to measure fluid viscosity, density and interfacial tension. Results of one-dimensional column studies indicated that micellar solubilization of residual PCE was rate-limited at Darcy velocities ranging from 0.8 to 8.2 cm/h and during periods of flow interruption. Effluent concentration data were used to develop effective mass transfer coefficient (Ke) expressions that were dependent upon the Darcy velocity and duration of flow interruption. To simulate subsurface heterogeneity, 2-D boxes were packed with layers of F-70 Ottawa sand and Wurtsmith aquifer material within 20-30 mesh Ottawa sand. A 4% Tween 80 solution was then flushed through PCE-contaminated boxes at several flow velocities, with periods of flow interruption. Effluent concentration data and visual observations indicated that both rate-limited solubilization and pooling of PCE above the fine layers reduced PCE recovery to levels below those anticipated from batch and column measurements. These experimental results demonstrate the potential impact of both mass transfer limitations and subsurface layering on the recovery of PCE during surfactant enhanced aquifer remediation.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

表面活性剂在北京碱性土壤中的吸附行为研究

通过静态吸附实验,研究了北京碱性土壤对阴离子表面活性剂SDS、阳离子表面活性剂CTAB和非离子表面活性剂Tween80的吸附行为,考察了温度对表面活性剂吸附的影响.结果表明:7种不同土样对SDS、CTAB和Tween80的吸附等温线均较好地符合Langmuir吸附模式,其吸附能力的大小顺序为2号轻壤土》轻粘土》中壤土》砂壤土》5号轻壤土》重壤土》紧砂土,这主要是由于7种土样的pH、有机质含量和机械组成不同的缘故;同一土壤中,CTAB的吸附量》Tween80的吸附量》SDS的吸附量;温度的升高,不利于SDS和CTAB在土壤中的吸附,而有利于Tween80的吸附.     

Combined effect of nonionic surfactant Tween 80 and DOM on the behaviors of PAHs in soil--water system

Batch experiments were performed to examine the desorption behavior of phenanthrene and pyrene in soil–water system in the presence of nonionic surfactant Tween 80 and dissolved organic matter (DOM) derived from pig manure or pig manure compost. Addition of 150 mg l⁻¹ Tween 80 desorbed 5.8% and 2.1% of phenanthrene and pyrene from soil into aqueous phase, respectively, while the addition of both Tween 80 and DOM derived from pig manure compost and pig manure could further enhance the desorption of phenanthrene to 15.8% and 16.2%, respectively, and 6.4% and 10.9%, respectively, for pyrene. In addition, our finding also suggested that subsequent addition of Tween 80 into the soil–water system could further enhance PAHs desorption. The enhancement effect of the co-existence of Tween 80 and DOM was more than the additive effect of the Tween 80 and DOM individually. It is likely that the formation of DOM–surfactant complex in the soil–water system may be a possible reason to explain such desorption enhancement phenomenon. Therefore, it is anticipated that the coexistence of both Tween 80 and DOM derived from pig manure or pig manure compost in soil environment will enhance the bioavailability of PAHs as well as other hydrophobic organic contaminants (HOCs) by enhancing the desorption during remediation process.     

Effect of Tween 80 and beta-cyclodextrin on degradation of decabromodiphenyl ether (BDE-209) by White rot fungi

The environmental safety of decabromodiphenyl ether (BDE-209), a widely used flame retardant, has been the topic of controversial discussions during the past several years. Degradation of BDE-209 into lower brominated diphenyl ether congeners, exhibiting a higher bioaccumulation potential, has been a critical issue. White rot fungi are known to degrade a wide variety of recalcitrant pollutants. In this work, white rot fungi were used to degrade BDE-209 in liquid culture medium, and the effects of Tween 80 and beta-cyclodextrin on BDE-209 degradation by white rot fungi were evaluated. On the basis of these results, it appears that BDE-209 could be degraded by white rot fungi, and Tween 80 and beta-cyclodextrin can both increase the biodegradation. The best result in Tween 80 experiments was obtained at a Tween 80 concentration of 500mgl(-1) within 10d, which showed 96.5% (w/w) BDE-209 transformed. Tween 80 at a high concentration will restrain the fungal growth and the degradation of BDE-209. However, beta-cyclodextrin had positive effects both on the BDE-209 degradation and the fungal growth.     

Removal of PCB-DNAPL from a rough-walled fracture using alcohol/polymer flooding

Phase behaviour experiments employing PCB (Aroclor 1242)/alcohol/water systems were conducted with ethanol (EtOH) and n-propanol (nPA). Both exhibited an affinity for the aqueous phase within the entire two-phase region. As much as 88% by volume (88% vol.) EtOH and 80% vol. nPA were necessary to achieve full miscibility of the PCB in the aqueous phase. DNAPL-water interfacial tension (IFT) was reduced from 38.9 dyn/cm to 4.7 dyn/cm and 2.4 dyn/cm with 80% vol. EtOH and 76% vol. nPA. The addition of alcohol brought about 41% and 54% reductions in DNAPL viscosity at maximal concentrations of EtOH and nPA. Density of the PCB-DNAPL was relatively unaffected by the presence of alcohol. A series of seven experiments were conducted where successive slugs of nPA and xanthan gum polymer solutions were injected into a fractured shale sample. A 30% vol. nPA solution injected under a hydraulic gradient of 0.36 allowed enhanced PCB removal primarily through reduction of IFT and resulted in 72% DNAPL recovery. Several pore volumes of alcohol solution were necessary to displace all the potentially mobile non-wetting phase since the high-viscosity DNAPL was mobilized at a lower flow rate than the overall fluid velocity, illustrating non-piston displacement. The injection of a 95% vol. nPA alcohol solution, theoretically at a sufficient concentration to produce fully miscible displacement of the residual DNAPL at equilibrium, resulted in non-equilibrium partitioning of the PCB into the flushing solution, likely due to the high fluid velocities in the fracture. The injection of 200 pore volumes of 95% vol. nPA solution resulted in 94% DNAPL recovery. Alcohol floods operated below the miscibility envelope appear to be a valuable source zone remedial alternative where the objective is to reduce DNAPL mobility to zero, but it should be noted that DNAPL mobility is increased during the application of the technology and steps may need to be taken to prevent unwanted vertical mobilization.     

Uptake of polycyclic aromatic hydrocarbons by Trifolium pretense L. from water in the presence of a nonionic surfactant

A greenhouse study examined plant uptake of phenanthrene and pyrene, as representatives of polycyclic aromatic hydrocarbons (PAHs), from an aqueous solution containing a nonionic surfactant Tween 80. The uptake was conducted with 1.0 mg l(-1) phenanthrene and 0.12 mg l(-1) pyrene under a wide range of Tween 80 concentrations (0-105.6 mg l(-1)). Tween 80 at the test concentrations did not show any apparent phytotoxity toward the growth of red clover (Trifolium pretense L.). At concentrations generally lower than 13.2 mg l(-1), Tween 80 enhanced the plant uptake based on the concentrations and PCFs (plant concentration factors) of these two PAHs. When present at higher concentrations, Tween 80 inhibited the uptake of both PAH compounds by the tested plant. The maximal plant uptake was observed at 6.6 mg l(-1) Tween 80, in which PAH concentrations and PCFs were 18-115% higher than those in Tween 80-free controls. The total mass removal (off-take) of phenanthrene and pyrene by root or shoot increased initially and decreased thereafter with the increase in Tween 80 concentrations. Although shoot biomass was evidently larger than root, the off-take was much higher in root than shoot because of the larger root concentrations of these chemicals. Results from this study show promises for the potential efficacy of enhanced phytoremediation in PAH contaminated sites using surfactant amendment.     

Environmental features of two commercial surfactants widely used in soil remediation

One of the main limitations for a wider application of surfactants in soil remediation is the lack of knowledge about environmental fate and toxicity of surfactant itself especially for in situ application. Sorption behaviour, biodegradability, toxicity of parent compound and its metabolites are important processes that affect environmental fate of surfactants in site remediation applications. Tween 80 (poly(oxyethylene)(20)-sorbitane monooleate) and Aerosol MA+80 (dihexyl sodium sulfosuccinate) are surfactants that have been tested in laboratory and field scale remediation of soil and groundwater. In this work, the sorption and biodegradability of these surfactants were assessed to provide conditions and limitations for their use. The soil used in this experimentation was analysed for organic carbon content, soil bacteria, and size fraction and resulted to be a good model because is characterised by mean values for almost all considered parameters. Tween 80 showed high degree of biodegradability but a high affinity for soil matrix. Results suggest that Tween 80 could find its best application in ex situ solid phase remediation like ex situ bioremediation; its high affinity to soil could limit in situ applications. Biodegradation tests for Aerosol MA+80 show low degree of biodegradability and mineralisation. Biodegradation experiments, coupled with analysis of toxicity, could support the hypothesis that degradation of Aerosol MA+80 is not complete and leads to an accumulation of intermediates with at least the same toxicity of the parental compound. Therefore, aquifer remediation application with Aerosol MA+80 has to be conducted with necessary precautions to avoid product loss and excess surfactant should be flushed from the soil.     

吐温80与氢氧化钠耦合强化剩余污泥溶胞效果的研究

利用吐温80的润湿、渗透作用,将其与氢氧化钠耦合应用于剩余污泥的溶胞。结果表明,吐温80的存在能有效提高氢氧化钠对剩余污泥的溶胞效果;而同样的溶胞效果下,吐温80的存在能降低溶胞的环境温度。吐温80与氢氧化钠耦合剩余污泥溶胞工艺的最佳工艺条件为：吐温80投加量100 mg/L、作用时间15 min,先加吐温80再加氢氧...     

Decolorization of mixtures of different reactive textile dyes by the white-rot basidiomycete Phanerochaete sordida and inhibitory effect of polyvinyl alcohol

We tried to decolorize mixtures of four reactive textile dyes, including azo and anthraquinone dyes, by a white-rot basidiomycete Phanerochaete sordida. P. sordida decolorized dye mixtures (200 mg l-1 each) by 90% within 48 h in nitrogen-limited glucose-ammonium media. Decolorization of dye mixtures needed Mn2+ and Tween 80 in the media. Manganese peroxidase (MnP) played a major role in dye decolorization by P. sordida. Decolorization of dye mixtures by P. sordida was partially inhibited by polyvinyl alcohol (PVA) that wastewaters from textile industries often contain. This was caused by an inhibitory effect of PVA on the decolorization of Reactive Red 120 (RR120) with MnP reaction system. Second addition of Tween 80 to the reaction mixtures in the presence of PVA improved the decolorization of RR120. These results suggest that PVA could interfere with lipid peroxidation or subsequent attack to the dye.     

Selection of surfactant in remediation of DDT-contaminated soil by comparison of surfactant effectiveness

With an aim to select the most appropriate surfactant for remediation of DDT-contaminated soil, the performance of nonionic surfactants Tween80, TX-100, and Brij35 and one anionic surfactant sodium dodecyl benzene sulfonate (SDBS) in enhancement of DDT water solubility and desorption of DDT from contaminated soil and their adsorption onto soil and ecotoxicities were investigated in this study. Tween80 had the highest solubilizing and soil-washing ability for DDT among the four experimental surfactants. The adsorption loss of surfactants onto soil followed the order of TX-100 > Tween80 > Brij35 > SDBS. The ecotoxicity of Tween80 to ryegrass (Lolium perenne L.) was lowest. The overall performance considering about the above four aspects suggested that Tween80 should be selected for the remediation of DDT-contaminated soil, because Tween80 had the greatest solubilizing and soil-washing ability for DDT, less adsorption loss onto soil, and the lowest ecotoxicity in this experiment.     

Combined treatment of PAHs contaminated soils using the sequence extraction with surfactant-electrochemical degradation

Polycyclic aromatic hydrocarbons (PAHs) cause a high environmental impact when released into the environment. The objective of this study was to evaluate the capacity of decontamination of polluted soils with PAHs using the sequence extraction-electrochemical treatment: extraction of PAHs from the soil with surfactant followed by electrochemical degradation of the liquid collected. Several PAHs (anthracene, benzo[a]pyrene, and phenanthrene) have been used as model compounds since such PAHs are found in high concentrations in contaminated environmental samples. Due to their hydrophobic nature, soil extraction has been limited. In this work, the use of six surfactants, Brij 35, Merpol, Tergitol, Tween 20, Tween 80 and Tyloxapol, has been evaluated on the PAH extraction from a model soil such as kaolin. Furthermore, the electrochemical degradation of PAHs with the surfactant that gave the best result was investigated working with neat solutions. The electrochemical treatment of these solutions was carried out in two electrochemical cells with different working volumes, 0.4 and 1.5l, and electrode material (graphite or titanium). Near complete degradation was reached for all the experiments in both cells.     

Surfactant-enhanced biodegradation of crude oil by mixed bacterial consortium in contaminated soil

This study evaluated the effects of two surfactants (i.e., Tween 80 and SDS) on biodegradation of crude oil by mixed bacterial consortium in soil-aqueous system. The mixed bacterial consortium was domesticated from the activated sludge of cooking plant through a progressive domestication process. High-throughput sequencing analysis revealed that Rhodanobacter sp. was the dominant bacteria. The higher CMC_eff value for two surfactants was observed in soil-aqueous system compared with that in aqueous system, which was likely due to their adsorption onto soil particles. Either Tween 80 or SDS can be utilized as carbon source and promote the growth of mixed bacterial consortium. Further findings evidenced that the degradation of crude oil can be enhanced by adding either Tween 80 or SDS. The performance of Tween 80 was generally superior to SDS for the crude oil degradation. The highest crude oil degradation efficiency was 42.2 and 31.0% under the conditions of 5 CMC_eff of Tween 80 and 2 CMC_eff of SDS, respectively. Furthermore, the degradation efficiency of crude oil in remediation experiment (i.e., 77%) evidenced that the integration of adding Tween 80 and inoculating mixed bacterial consortium was effective for crude oil-contaminated soil decontamination.     

Effects of pig manure compost and nonionic-surfactant Tween 80 on phenanthrene and pyrene removal from soil vegetated with Agropyron elongatum

This paper evaluates the effects of pig manure compost (PMC) and Tween 80 on the removal of phenanthrene (PHE) and pyrene (PYR) from soil cultivated with Agropyron elongatum. Soils spiked with about 300mgkg(-1) of PHE and PYR were individually amended with 0%, 2.5%, 5% and 7.5% (dry wt) of PMC or 0, 20 and 100mgkg(-1) of Tween 80. Unplanted and sterile microcosms were prepared as the controls. PAH concentration, total organic matter (TOM), dissolved organic carbon (DOC), total heterotrophic and PAH degrading microbial populations in soil were quantified before and after 60d period. The results indicated that A. elongatum could significantly enhance PYR removal (from 46% to 61%) but had less impact on PHE removal (from 96% to 97%). Plant uptake of the PAHs was insignificant. Biodegradation was the key mechanism of PAH removals (<3% losses in the sterile control). Increase in PMC or Tween 80 levels increased the removal of PYR but not of PHE. Maximal PYR removal of 79% and 92% were observed in vegetated soil receiving 100mgkg(-1) Tween 80 and 7.5% PMC, respectively. Enhanced PYR removal in soil receiving PMC could be explained by the elevated levels of DOC, TOM and microbial populations as suggested by Pearson correlation test. While the positive effect of Tween 80 on PYR removal could probably due to its capacities to enhance PYR bioavailability in soil. This paper suggests that the addition of either PMC or nonionic-surfactant Tween 80 could facilitate phytoremediation of PAH contaminated soil.     

The effects of pruning and nodal adventitious roots on polychlorinated biphenyl uptake by Cucurbita pepo grown in field conditions

Two cultivation techniques (i-pruning and ii-nodal adventitious root encouragement) were investigated for their ability to increase PCB phytoextraction by Cucurbita pepo ssp pepo cv. Howden (pumpkin) plants in situ at a contaminated industrial site in Ontario (Aroclor 1248, mean soil [PCB] = 5.6 μg g⁻¹). Pruning was implemented to increase plant biomass close to the root where PCB concentration is known to be highest. This treatment was found to have no effect on final shoot biomass or PCB concentration. However, material pruned from the plant is not included in the final shoot biomass. The encouragement of nodal adventitious roots at stem nodes did significantly increase the PCB concentration in the primary stem, while not affecting shoot biomass. Both techniques are easily applied cultivation practices that may be implemented to decrease phytoextraction treatment time.     

简青霉降解秸秆条件最优化和诱导剂的作用

实验中采用简青霉对稻草秸秆进行降解作用,通过正交实验的极差、三因素三水平作用趋势图和降解选择性分析,对影响简青霉降解稻草秸秆的3种因素进行了优化,得到培养温度40℃、含水率80%、培养pH为8是降解的最佳固态发酵培养条件。并研究了碱木质素对简青霉分泌木质素降解酶的诱导作用,不同浓度的碱木质素对简青霉产酶的诱导作用不同,且对不同酶的诱导效果也不同,最后得到较低浓度0.5和1 g/L是诱导的适宜浓度。对比较适浓度的碱木质素和常用的诱导剂愈创木酚、吐温80的诱导作用,发现在同样的培养条件下,碱木质素的诱导效果比愈创木酚和吐温80效果都好。     

Biodegradation of polychlorinated biphenyls using biofilm grown with biphenyl as carbon source in fluidized bed reactor

This study investigated the use of biofilms in the biodegradation of polychlorinated biphenyls. The biofilm used was developed on modified cement particles using mixed microbial culture isolated from PCB-contaminated soil. The biofilm formed was first acclimatized to PCBs by feeding the reactor alternately with biphenyl and PCBs. The acclimatized biofilm was tested on simulated PCB-contaminated water containing Aroclor 1260 by using a three-phase fluidized-bed reactor operated in batch mode. The initial batch run yielded 80+/-2.38% PCB removal from medium in one day and 91+/-1.34% in 5 days. The percent PCB removal gradually increased in the succeeding runs reaching 92+/-2.48% in one day and a steady state value of 95+/-2.01% in 5 days from batch eight onwards. PCB removal from the medium was highest during the first day reaching 80-92%. The sudden decrease in PCB concentration was attributed to an initial adsorption of the PCB on the biofilm and then the compound was degraded gradually. Yellow intermediates were observed as the pH of the medium decreased. These intermediate products were further metabolized as indicated by the disappearance of the yellow substance.